DescrizioneLa climatizzazione della vettura viene realizzata attraverso il gruppo convogliatore/distributore con riscaldatore.La climatizzazione viene controllata agendo sulle tre manopole di comando poste sulla plancia:la manopola di sinistra comanda lo sportello di miscelazione tra aria calda e fredda;la manopola di destra comanda l'apertura degli sportelli che regolano la distribuzione dei flussi di aria;la manopola centrale regola la ventilazione dell'aria a quattro differenti velocita;iIl pulsante di destra inserisce il lunotto termico ed accende il relativo led.3015487VedereE3030SBRINAMENTO LUNOTTO E SPECCHI RETROVISORI.Il pulsante centrale premuto inserisce la funzione di ricircolo dell'aria; a pulsante premuto si accende il relativo led. Se il pulsante non e premuto affluisce invece aria "dinamica" dall'esterno.Un'apposita centralina elettronica gestisce il funzionamento del sistema controllando:distribuzione aria alle bocchette;velocita ventilatore (a variazione continua);inserimento del ricircolo dell'aria;La centralina imposta i suddetti parametri in modo da ottenere l'adeguamento della temperatura dell'abitacolo a quella richiesta. In base alla richiesta impostata, la centralina stabilisce la velocita di entrata dell'aria nell'abitacolo tramite il motore ventilatore e la temperatura della stessa tramite un attuatore di miscelazione; imposta inoltre la distribuzione dei flussi con un altro attuatore ed infine con un ultimo attuatore la funzione di ricircolo dell'aria interna /aria esterna. Per maggiori dettagli 3014704Descrizioni e Funzionamento5020RISCALDATORE . Il Body Computer acquisisce continuamente il segnale "tensione batteria' per confrontarlo con un proprio valore limite: se il livello di tensione batteria rilevato e inferiore alla soglia, interviene tramite rete CAN inviando un segnale per disabilitare una serie di carichi: tra questi disattiva il comando del ventilatore.La centralina di climatizzazione e alimentata da una linea "sottochiave' protetta da un fusibile della centralina sottoplancia; il ventilatore e alimentato da una linea protetta da uno specifico fusibile della centralina vano motore.
Descrizione funzionale La centralina di climatizzazione M70 e alimentata sotto chiave (INT/A) al pin 3 dalla linea protetta dal fusibile F31 della centralina sottoplancia B2 .; e alimentata direttamente al pin 2 dalla linea protetta dal fusibile F39 della centralina sottoplancia B2 . Il pin 1 di M70 e a massa. L'attuatore il ricircolo N82 e comandato dalla centralina M70 dai pin 14, 15, 16 e 17. L'attuatore di miscelazione N81 e comandato dalla centralina M70 dai pin 23, 24, 25 e 26. L'attuatore di distribuzione N80 e comandato dalla centralina M70 dai pin 19, 20, 21 e 22. Un regolatore elettronico M72 aziona con un comando di massa l'elettroventilatore N85 a diverse velocita: esso e alimentato "sotto chiave' (INT/A) dalla linea protetta dal fusibile F31 della centralina sottoplancia B2 ..riceve in ingresso dalla centralina un segnale di controllo dal pin 10 e restituisce un segnale di feedback al pin 18 di M70 . L'elettroventilatore N85 e alimentato direttamente dalla linea protetta dal fusibile F5 della centralina vano motore B1 - Tramite la linea CAN, la centralina M70 si collega - dai pin 12 e 13 - al Body Computer M1 e al nodo H44 [EL1050], scambiando tra gli altri i seguenti segnali:segnale "tensione batteria;segnale inserimento lunotto.
0Stacco201Riattacco211. Svitare le viti di fissaggio del motorino.2. Scollegare la connessione elettrica del motorino.3. Rimuovere il motorino (3a) disimpegnando la sua ruota dentata(3b) dalla cremagliera della camma.2004835
0Stacco201Riattacco211. Svitare le viti di fissaggio del motorino.2. Scollegare la connessione elettrica del motorino (2a, 2b, 2c,2d).3. Rimuovere il motorino (3a) disimpegnando il suo collegamento(3b).2004840
0Stacco201Riattacco211. Operando sotto il lato destro del rivestimento plancia, svitarei dadi di fissaggio della paratia.2. Rimuovere la paratia.2004805
5040C34
0Stacco201Riattacco211. Scollegare la connessione elettrica.2. Svitare la vite di fissaggio dell'elettroventilatore.3. Ruotare ed estrarre l'elettroventilatore.2004807
5040C44
0Stacco201Riattacco211. Operando sotto il lato destro del rivestimento plancia, svitarei dadi di fissaggio della paratia.2. Rimuovere la paratia.2004808
0Stacco201Riattacco211. Svitare le viti di fissaggio del riparo per la valvola di espansione.2. Rimuovere il riparo.2004815
5040C80
0Stacco201Riattacco211. Scollegare la connessione elettrica del motorino di immissionee ricircolo aria.2. Svitare la vite.3. Ruotare il gruppo di immissione e ricircolo aria e rimuoverlo.2004824
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.