BeschreibungDie Fahrtrichtungsleuchten rechts und links werden durch Hoch- oder Herunterstellen des entsprechenden Hebels am linken Lenksaulenschalter eingeschaltet. Die Funktion ist mit dem Zundschlussel auf MAR aktiv.Die Warnblinkleuchten (Fahrtrichtungsleuchten rechts und links gleichzeitig eingeschaltet) werden durch eine Taste im mittleren Bedienfeld eingeschaltet. -- Au?erdem wird eine LED hinter dem Druckknopf synchron zu den Blinkern eingeschaltet. Die Funktion ist immer aktiv.Die Einschaltung von Warnlicht und Fahrtrichtungsanzeiger wird vom Body Computer auch mit der Blinkfrequenz gesteuert und durch die serielle CAN-Leitung an die anderen Knoten mitgeteilt.Auf diese Weise werden auch die zwei Kontrollleuchten fur Fahrtrichtung in der Instrumententafel eingeschaltet. Zusammen mit dem Blinken der Kontrollleuchten ertont ein niederfrequentes akustisches Zeichendurch das Relais im Body Computer.Die korrekte Funktion der Leuchten wird vom 'Check'-Gerat fur die Fahrtrichtungsanzeiger rechts und links kontrolliert:Unterbrechung, Lampe fehlt, Lampenleistung 21 W (vorne und hinten rechts bzw. vorne und hinten links),Masseschluss (Lampe oder Verkabelung),Kurzschl. gegen Vbatt (Kurzschlu? Verkabelung gegen Vbatt),falsche Lampe: 5 W statt 21 W.Bei einer der obigen Storungen zeigt der Body Computer diese uber das CAN-Netz an: In der Instrumententafel wird die Kontrollleuchte 'Storung Beleuchtung' eingeschaltet und eine Meldung am Display angezeigt. Auch das Fehlen einer Lampe von 21 W hinten oder vorne wird durch Erhohung der Blinkfrequenz und ein akustisches Zeichen (Summer) angezeigt. Die Fahrtrichtungslampen werden auch zur Anzeige des Befehls fur Offnung/Schlie?ung der Turen durch die Fernbedienung eingeschaltet. 3038900SieheE3040ZENTRALVERRIEGELUNG3039177SieheE7015ALARM
Funktionsbeschreibung Die Signale der Fahrichtungsanzeiger werden zu Pin 7 des Steckers D und 30 des Steckers B vom Body Computer M1 durch den Lenksaulenschalter H5 geleitet. Das Signal 'Schlussel auf MAR' (INT) vom Umschalter H1 erreicht den Verteiler im Armaturenbrett B2 , Pin 11 des Steckers H, und von hier den Body Computer M1 (Pin 9 des Steckers F). Das Signal Warnblinken EIN erreicht Pin 34 des Steckers B von M1 aus dem Druckknopf im mittleren Bedienfeld H12 . Wenn dieses Signal anliegt, schaltet der Body Computer M1 die Stromversorgung der seitlichen Fahrtrichtungsanzeiger F20 (links) und F2 (rechts) durch Pin 2 und 22 des Steckers A, der Leuchten vorne F18 (links) und F19 (rechts) durch Pin 38 und 39 des Steckers A sowie der Leuchten hinten F30 (links) und F31 (rechts) durch Pin 12 und 3 des Steckers E. Der Body Computer M1 schaltet seinerseits uber die CAN-Leitung die Kontrollleuchte 'Fahrtrichtungsanzeiger', Summer und bei Storung die Leuchte 'Storung der Beleuchtung' in der Instrumententafel E50 ein. Von Pin 29 des Steckers B von M1 wird ein Signal gegeben, damit die LED im Druckknopf H12 angeht.
0Ausbau201Wiedereinbau213041404-7040A37Sicherungen - Kastendeckelauf dem Armaturenbrett a.u.e.1. Die elektrischen vorderseitigen Anschlusse (1a, 1b, 1c, 1d,1e, 1f) abklemmen.2. Befestigungsschrauben der Elektronik losen.3. Die angegebenen Befestigungsschrauben der Armaturenverkleidungabschrauben.2004865
0Ausbau201Wiedereinbau211. Prufen, ober Zundschlussel auf 'STOP' steht, dann Minuskabel(-) von der Batterie abklemmen.2. Den Deckel des Sicherungskastens 'Maxi-Fuse' offnen.3. Befestigungsschrauben des 'Maxi-Fuse'-Sicherungskastens herausschrauben.4. Schraubenbolzen am Pluspol (+) der Batterie lockern.5. Sicherungskasten 'Maxi-Fuse' von der Batterie trennen und seitlichverschieben.2004975
5530B14
Vorsichtma?nahmenbeachten:769768768
5530B18
Folgende Hinweisebeachten769Bei Batterien mit optischem Standmesserist es moglich, den Stand des Elektrolyts und den Ladezustand derBatterie je nach Farbe des optischen Anzeigers zu ermitteln. eine klare und weisse Farbe zeigt einenunausreichenden Elektrolytstand an: mit destilliertem Wasser auffulleneine dunkle Farbe ohne grunes Feld zeigteinen korrekten Elektrolytstand mit niedriger Batterieladung an:die Batterie muss geladen werden. eine dunkle Farbe mit grunem Bereich inder Mitte zeigt einen korrekten Elektrolyt- und Ladezustand der Batteriean: es muss keinerlei Eingriff durchgefuhrt werden. Fur weitere Einzelheiten siehe BESCHREIBUNG UNDFUNKTIONSWEISE 5530.768Wie folgt vorgehen:Leerlaufspannung der Batterie mit dem vomKD empfohlenen Me?gerat 'MICRO 360' messen. Je nach gemessenem Spannungswert, der denLadezustand anzeigt, wie folgt vorgehen:Bei Leerlaufspannung unter 12,10 V dieBatterie ersetzen (siehe Arbeit 5530B10).Bei Leerlaufspannung uber 12,10 V, aberunter 12,50 V die Batterie nachladen (siehe Arbeit 5530B14).Bei Leerlaufspannung uber 12,50 V istdie Batterie geladen.Ggf. den Saurestand wie folgt erganzen:Band mit den Verschlussen abziehen.Destilliertes, entionisiertes Wasser nachfullen.Vorsicht, da? keine Spritzer nach au?en verursacht werden.768
0Ausbau201Wiedereinbau21Das Fahrzeug auf die Hebebuhne fahren.Motorhaube offnen.1. Halterungen (1a) offnen und den Deckel (1b) abnehmen2004980
5530B40
0Ausbau201Wiedereinbau21Motorhaube offnen.1. Halterungen (1a) offnen und den Deckel (1b) abnehmen2004986
5530B52
0Ausbau201Wiedereinbau21Mit dem Ausbau fortfahren 3041136-5530B10Batterie a.u.e. .1. Deckel vom Sicherungs- und Relaiskastengehause entfernen.2. Mutter (2a) herausschrauben und Massekabel (2b) des Sicherungs-und Relaiskastens trennen.2004990
5530B60
0Ausbau201Wiedereinbau213041136-5530B10Batterie a.u.e.1. Batterieablage entfernen.2. Die Schrauben (2a) abschrauben und die Schraube (2b) zur Befestigungdes Batteriekorbes lockern.3. Leicht den Batteriekorb verschieben.4. Halteknopf des Riemens losen.5. Riemen entfernen.2005002
0Ausbau201Wiedereinbau211. Halter der Schalterblende von der Armaturenbrettverkleidung losen.2. Elektrischen Anschluss abziehen.3. Schalterblende abnehmen.2005045
0Ausbau201Wiedereinbau211. Seitliche Fahrtrichtungsleuchte von der angegebenen Seite auslosen.2. Elektrischen Anschluss abklemmen und seitliche Fahrtrichtungsleuchteabnehmen.2005030
0Ausbau201Wiedereinbau213041222-5580E08Antenne fur Wegfahrsperrea.u.e.1. Elektrische Anschlusse (1a, 1b) vom Anlasserschalter abklemmen.2. Eine Plombe und die kopflosen Schrauben (2a) abschrauben. Anlasserschalter(2b) entfernen.7682004913
5520A14
769
5520A16
769
5520A18
0Ausbau201Wiedereinbau211. Ggf. Lenkradverstellhebel benutzen.2. Befestigungsschrauben der unteren Abdeckung losen.3. Untere Abdeckung von den Innenhalterungen und dem Lenkrad losen.2004920
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.