BeschreibungDas Fahrzeug ist mit mehreren Leuchten fur die optimale Beleuchtung von Instrumenten und Bedienungen ausgestattet.Einige Bedienungen werden erst mit dem Zundschlussel auf MAR, andere bei eingeschaltetem Standlicht und andere mit unterschiedlicher Helligkeit beleuchtet, die uber den Body Computer durch das Potentiometer geregelt wird.Bei Drehen des Zundschlussels auf MAR leuchten auf:Schalter Fensterheber an der Vordertur Beifahrerseite,Betatigung Warnblinkanlage, Nebelscheinwerfer, Nebelschlussleuchte,Leuchtweitenregelung, Helligkeitsregelung, Ruckstellung des km-Zahlers,Autoradio,Schaltergruppe am Tunnel.Der Body Computer verwaltet die Freigabesignale mit dem Zundschlussel auf MAR (INT) und fur das Standlicht fur die Belechtung von:Zigarettenanzunder und Aschenbecher,Verbindung mit Funktelefon.Alle Instrumente leuchten auf, wenn der Zundschlussel in Fahrstellung MAR gedreht wird.Die Helligkeit wird in 11 Stufen mit der externen Taste auf dem Bedienfeld neben dem Lenkrad eingestellt. (von 0 bis 10).Die mit den Tasten 'MODE +' und 'MODE -' eingestellte Helligkeit wird an der Instrumententafel angezeigt. Die Einstellung wird auch gespeichert und spater eingesetzt.767Die Helligkeit kann jedoch nicht bis auf Null reduziert werden.Der Helligkeitswert wird durch das CAN-Netz zu den Knoten Radio (oder integriertem Radio-Telefon-Navigator) und zur Klimaelektronik geleitet, damit die Hintergrundbeleuchtung der Displays gedampft wird: Von der max. Beleuchtung (Tag) schaltet das System auf die geregelte Nachtbeleuchtung um. Die gleiche Logik gilt auch fur die Bedienungstasten.Die Beleuchtung der Instrumententafel, ausgenommen Tacho, kann durch langeren Druck (4 - 10 s) auf die Taste 'MODE' deaktiviert werden.Falls eine nicht beleuchtete Anzeige eine Warnung erhalt (z.B. Kraftstoffreserve, zu hohe Kuhlflussigkeitstemperatur usw.), wird stets die Beleuchtung aller Instrumente eingeschaltet.In der Instrumententafel 'GRUNDVERSION': Wenn das Standlicht ausgeschaltet ist, werden die Displays stets mit 100% Helligkeit beleuchtet.Wenn das Standlicht eingeschaltet ist, werden Grafik und Display mit dem eingestellten Helligkeitswert beleuchtet.In der Instrumententafel 'GEHOBENE VERSION': Die Beleuchtung der Displays kann immer geregelt werden (mit oder ohne Standlicht).
Funktionsbeschreibung Die Stromleitung 'Zundschlussel auf MAR' (INT) mit der Sicherung F39 im Verteiler unter dem Armaturenbrett B2 beleuchtet den Schalter des Scheibenhebers in der Vordertur Beifahrerseite H50 , die Schalter fur Warnblink, Nebelscheinwerfer, Nebelschlussleuchte H12 , die Leuchtweitenregelung, die Helligkeitsregelung, die Ruckstellung des km-Zahlers H10, den Vorbereitungsstecker fur Telefon D75, den Schalterblock auf dem Mitteltunnel H35 und das Radio P20 in der GRUNDVERSION (ohne Display). Bei eingeschaltetem Standlicht wird der Strom indessen vom Body Computer M1 , Pin 18 des Steckers C, an den Zigarettenanzunder P50 und an den Vorbereitungsstecker fur das Telefon D75 geliefert. Die Bedienungen 'MODE' und 'KM' in der Gruppe H10 erhalten ebenfalls Strom von der Leitung (INT) mit der Sicherung F39 im Verteiler B2 und leiten den Befehl zur Instrumententafel E50 , Pin 16 des Steckers B und Pin 9 des Steckers A. Uber die CAN-Leitung steht der Body Computer M1 mit der Instrumententafel E50 in Verbindung, die das Signal 'Helligkeitsregelung' zum Knoten Radio (oder integriertem Radio-Telefon-Navigator) und zur Klimaelektronik 3038761SieheE1050CAN-VERBINDUNGSLEITUNGEN leitet.
0Ausbau201Wiedereinbau213041404-7040A37Sicherungen - Kastendeckelauf dem Armaturenbrett a.u.e.1. Die elektrischen vorderseitigen Anschlusse (1a, 1b, 1c, 1d,1e, 1f) abklemmen.2. Befestigungsschrauben der Elektronik losen.3. Die angegebenen Befestigungsschrauben der Armaturenverkleidungabschrauben.2004865
0Ausbau201Wiedereinbau211. Prufen, ober Zundschlussel auf 'STOP' steht, dann Minuskabel(-) von der Batterie abklemmen.2. Den Deckel des Sicherungskastens 'Maxi-Fuse' offnen.3. Befestigungsschrauben des 'Maxi-Fuse'-Sicherungskastens herausschrauben.4. Schraubenbolzen am Pluspol (+) der Batterie lockern.5. Sicherungskasten 'Maxi-Fuse' von der Batterie trennen und seitlichverschieben.2004975
5530B14
Vorsichtma?nahmenbeachten:769768768
5530B18
Folgende Hinweisebeachten769Bei Batterien mit optischem Standmesserist es moglich, den Stand des Elektrolyts und den Ladezustand derBatterie je nach Farbe des optischen Anzeigers zu ermitteln. eine klare und weisse Farbe zeigt einenunausreichenden Elektrolytstand an: mit destilliertem Wasser auffulleneine dunkle Farbe ohne grunes Feld zeigteinen korrekten Elektrolytstand mit niedriger Batterieladung an:die Batterie muss geladen werden. eine dunkle Farbe mit grunem Bereich inder Mitte zeigt einen korrekten Elektrolyt- und Ladezustand der Batteriean: es muss keinerlei Eingriff durchgefuhrt werden. Fur weitere Einzelheiten siehe BESCHREIBUNG UNDFUNKTIONSWEISE 5530.768Wie folgt vorgehen:Leerlaufspannung der Batterie mit dem vomKD empfohlenen Me?gerat 'MICRO 360' messen. Je nach gemessenem Spannungswert, der denLadezustand anzeigt, wie folgt vorgehen:Bei Leerlaufspannung unter 12,10 V dieBatterie ersetzen (siehe Arbeit 5530B10).Bei Leerlaufspannung uber 12,10 V, aberunter 12,50 V die Batterie nachladen (siehe Arbeit 5530B14).Bei Leerlaufspannung uber 12,50 V istdie Batterie geladen.Ggf. den Saurestand wie folgt erganzen:Band mit den Verschlussen abziehen.Destilliertes, entionisiertes Wasser nachfullen.Vorsicht, da? keine Spritzer nach au?en verursacht werden.768
0Ausbau201Wiedereinbau21Das Fahrzeug auf die Hebebuhne fahren.Motorhaube offnen.1. Halterungen (1a) offnen und den Deckel (1b) abnehmen2004980
5530B40
0Ausbau201Wiedereinbau21Motorhaube offnen.1. Halterungen (1a) offnen und den Deckel (1b) abnehmen2004986
5530B52
0Ausbau201Wiedereinbau21Mit dem Ausbau fortfahren 3041136-5530B10Batterie a.u.e. .1. Deckel vom Sicherungs- und Relaiskastengehause entfernen.2. Mutter (2a) herausschrauben und Massekabel (2b) des Sicherungs-und Relaiskastens trennen.2004990
5530B60
0Ausbau201Wiedereinbau213041136-5530B10Batterie a.u.e.1. Batterieablage entfernen.2. Die Schrauben (2a) abschrauben und die Schraube (2b) zur Befestigungdes Batteriekorbes lockern.3. Leicht den Batteriekorb verschieben.4. Halteknopf des Riemens losen.5. Riemen entfernen.2005002
0Ausbau201Wiedereinbau211. Halter der Schalterblende von der Armaturenbrettverkleidung losen.2. Elektrischen Anschluss abziehen.3. Schalterblende abnehmen.2005045
0Ausbau201Wiedereinbau213041222-5580E08Antenne fur Wegfahrsperrea.u.e.1. Elektrische Anschlusse (1a, 1b) vom Anlasserschalter abklemmen.2. Eine Plombe und die kopflosen Schrauben (2a) abschrauben. Anlasserschalter(2b) entfernen.7682004913
5520A14
769
5520A16
769
5520A18
0Ausbau201Wiedereinbau211. Ggf. Lenkradverstellhebel benutzen.2. Befestigungsschrauben der unteren Abdeckung losen.3. Untere Abdeckung von den Innenhalterungen und dem Lenkrad losen.2004920
0Ausbau201Wiedereinbau211. Schalterbrett (1a) von den Halterungen (1b) ziehen.2. Elektrische Verbindung abklemmen.3. Schalterbrett abnehmen.2005348
7040L35
0Ausbau201Wiedereinbau211. Armlehne hochklappen.2. Abdeckblende in Pfeilrichtung abnehmen.3. Befestigungsschraube der Armlehne herausschrauben.4. Armlehne ausbauen.2005349
7040L40
0Ausbau201Wiedereinbau211. Schrauben herausschrauben2. Turdichtung im Bereich der Fu?leiste abnehmen.3. Fu?leiste (3a) mit entsprechendem Werkzeug von den Innenhalterungen(3b) entfernen.2005350
7040L44
0Ausbau201Wiedereinbau211. Rucksitzpolster anheben.2. Befestigungsschrauben der Fussleiste ausschrauben.3. Fussleiste entfernen.2005351
Schalter Fensterheber vorne an der Beifahrerseite.
0Ausbau201Wiedereinbau213041197-5570T61Multifunktionsantennea.u.e.1. Elektrischen Anschluss abklemmen.2. Anschluss des Antennenkabels abziehen.3. Spezialmutter abschrauben.4. Antennenhalterung mit Kabeln entfernen.2005046
5570T61
0Ausbau201Wiedereinbau211. Die Antenne abschrauben.2005048
5570T66
0Ausbau201Wiedereinbau213041213-5580C18Fahrer-Airbag kompletta.u.e.7681. Elektrischen Anschluss abklemmen.2. Schalterblende (2a) trennen und von den Halterungen losen.2005049
5570T80
0Ausbau201Wiedereinbau21Mit dem Fahrzeug mitgelieferteWerkzeuge zum Ausbau des Autoradios holen.1. Die beiden Werkzeuge in die entsprechenden Offnungen an derFrontblende des Autoradios einsetzen und bis zum Ausrasten der Verankerungeindrucken. 2005050
5570T85
0Ausbau201Wiedereinbau21Die Hecktur offnen.1. Die Befestigungsschrauben des CD-Lesers der Audioanlage losen.2005053
0Ausbau201Wiedereinbau211. Blenden abhebeln.2. Schrauben herausschrauben3. Den Haltegriff entfernen.2005492
7065C33
0Ausbau201Wiedereinbau211. Befestigungsschraube der Sonnenblende herausschrauben.2. Die Sonnenblende leicht zur Seite schieben.3. Elektrische Verbindung abklemmen.2005493
7065C42
0Ausbau201Wiedereinbau211. Deckel des Aschenbechers offnen.2. Aschenbecher herausnehmen.2005495
7065C68
0Ausbau201Wiedereinbau211. Spiegelhalterung (1a) anheben und nach oben vom Halteblock (1b)abziehen, der an der Scheibe befestigt ist.2005496
7065C69
0Ausbau201Wiedereinbau21Beschrieben wird der Wiedereinbaudes Plattchens, weil es, wenn es richtig sitzt, nicht von der Scheibe getrenntwerden kann. 769
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.