DescriptionThe car is equipped with two supplementary front foglamps for use in poor visibility.The rear fog lamps are activated by a button on the central console; the ideogram is lit up when the ignition is switched ON.The front fog lamp circuit is protected by a special fuse and controlled by a specific relay located in the relay control unit on the left side of the engine bay.An LED in the on button signals that the lights are on.The foglamps are enabled under the following conditions:with the key in the ON positionside lights on
Functional description The front fog lamps F15 (left) and F16 (right) are supplied through the front fog lamps relay R5 located in the relay unit B3 . The relay is supplied directly from the battery through the fuse line F3 of the relay unit B3 . The operation of the front fog lamps is also controlled by the electronic Check device M45 , which receives the control signal from the switch and controls the bulbs. The supply for the Check device M45 arrives directly from the battery (maxifuse CENTR of B5 ) at pins 1 and 6 of connector C, via fuse F11 of junction unit B1 . The supply controlled by the ignition (INT/A) arrives via fuse F1 of junction unit B1 at pin 9 of connector C: pin 7 of connector C is earhed. The device M45 receives as an input the signal for fog lights switched on by the button located in unit H35 - pin 10 of connector A; this signal only arrives if the side lights are on. in response to this signal, device M45 sends the command to the fog lights relay R5 of B3 from pin 1 of connector D. At the same time a signal is sent to unit H35 , from pin 7 of connector B, so as to light up the LED near the button which indicates the 'front fog lamps on' function. The supply for this LED for H35 is controlled by the ignition (INT/A) via fuse F5 of junction unit B1 ; this line allows the lighting of the control panel H35 controlled by the ignition (INT/A).
0Removing201Refitting213314824-5505A18multi-function controlunit - r r . 1. Undo the bolt (1a) and push back the junction unit as far asnecessary to disconnect the electrical connections (1b).767For precise identification ofthe electrical connections, see Wiring Diagrams Section.2. Remove the junction unit.2010592
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Unscrew bolt (1a) and open fuse access cover (1b).2. Undo the bolt (2a) and remove the integrated multiservices unit(2b) after having disconnected the electrical connections (2c),(2d), (2e), (2f) and (2g).2010595
5505A29
0Removing201Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b) for theadditional junction unit.2071293
0Removing201Refitting213314864-5530B54battery cover - r+r . Make sure that the ignition key is in theOFF position.1. Disconnect the battery negative and positive terminals.2. Undo the bolt (2a) fixing the battery retaining bracket (2b).3. Remove the battery.2010647
5530B40
0Removing201Refitting213314864-5530B54battery cover - r+r1. Press and release the retainers (1a), then remove the cover (1b)for the supply box on the battery. 2071303
0Removing201Refitting211. Rotate the fog light cover in an anti-clockwise direction, thenextract it.2071327
5540D38
Prepare the vehicle complete with sparewheel, tools, fluids, fuel reserve and driver on board.Check that the tyre inflation pressureis correct.Position the vehicle on a flat surface,perpendicular to a screen or an opaque surface, 10 metres away,which contains a line corresponding to the height from the ground(A) of the centre of the fog lamps. 1. Switch on the fog lights and regulate the adjustment screw (1a)so that the demarcation line between the dark area and the areathat is lit by the light beam is at height B = (2/3 A - 8) cm 2071330
0Removing201Refitting21Ensure that the ignition keyis in stop position, then disconnect the battery negative terminal1. Undo the bolt (1b) and open the fuse access cover (1b).2. Remove the complete exterior light switch (2a) from its housingusing the tool (2b).767Exert pressure inside the exteriorlights switch to facilitate its removal.3. Disconnect the electrical connections (3a), (3b) and (3c) andremove the exterior lights switch (3d).2010651
5540A56
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Undo the knob (1b) and open the protective cover (1a).2010652
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Undo the fixing knob (1b) and open the access cover (1a) .2. Disconnect the electrical connection from the inner rear lightcluster.3. Undo the nuts (3a) and remove the inner rear light cluster (3b).2010654
5540A74
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Open the access cover after having undone the fixing knob.2. Release the retaining tabs (2a) and extract the bulb holder (2b)from its housing.3. Replace the rear fog lamps bulb (3a) or the reversing lightsbulb (3b) or the side lights bulb (3c).2010655
5540A80
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Undo the knob (1b) and open the protective cover (1a).2010656
5540A94
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Using the tool (1a), remove the complete number plate light (1b).2. Disconnect the electrical connection and remove the number platelight.2010658
0Removing201Refitting21With the ignition key in the stop position,disconnect the battery negative terminal.1. Release the gear lever boot from its seat on the console.2. Undo the handbrake lever boot stud from its seat on the consoleand release from the lever.3. Unscrew the console retaining bolts. 4. Disconnect the cigar lighter and ashtray light electrical connection.5. Remove the trim by withdrawing from the handbrake lever.2010988
7040L40
0Removing201Refitting211. Unscrew the retaining bolt in the upper corner of the sill plate.2. Use tool (2a) to prise sill plate (2b) up from the underlyingretainers.2010989
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.