DescriptionThe rear door electrically-operated windows can be operated by switches on the front driver's door or switches located on each of the rear doors.Operation of the rear electrically-operated windows is manual (the window is raised/lowered only when the switch is pressed).For safety reasons, a special lock switch on the driver's door cuts off power to all switches to prevent accidental activation from the rear seats, e.g. when children are present.The seat heating circuit is protected by a special fuse and is controlled by a relay which supplies other services controlled by the ignition. The fuse is located on the fuse and relay box located in the luggage compartment, while the relay is located in the junction unit.The rear electrically-operated windows will work only when the key is turned to MAR.The control switch symbols are lit when the key is turned to MAR.
Functional description The control unit M82 manages the operation of the electric rear windows. The direct supply for the control unit M82 comes in through special fuse B17 . The ignition-dependent supply (INT/A) reaches pin 4 of connector B of relay R1 , from the line protected by fuse F9 , both contained in the junction unit B1 . The ignition-dependent supply (INT/A) of the line protected by fuse F5 of the junction unit B1 supplies the electric window control unit on the driver's door H44 and the switches H53 and H54 (on rear right and rear left doors respectively). Pins 3 of connector B and 1 of connector E supply the earth, C31 . When the switches are operated, they send command signals (positive and negative) to the rear electric windows control unit M82 , but only if the safety switch in unit H44 is set to enabled posiion. If it is not, it cuts off the supply to both the switches on the driver's door and the switches on the rear doors. With the safety switch in the enablement position, the switches are illuminated when the ignition is on (MAR). The block switch is also illuminated when the ignition is on, by a specific LED supplied by the line protected by fuse F5 of junction unit B1 : The above signals arrive:at pins 3 and 4 of connector A from switch H53 or from the switch H44 , to control the left electric windowat pins 1 and 2 of connector C from switch H54 , to control the right electric windowat pins 5 and 6 of connector A from switch H44 , to control the right electric window.The control unit M82 controls the electric windows as described above:from pins 1 and 2 of connector D it sends commands to the rear left motor N65 ;from pins 3 and 4 of connector D it sends commands to the rear right motor N66 .When the positive and negative signals are reversed, the motor direction of rotation is also reversed.
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314824-5505A18multi-function controlunit - r r . 1. Undo the bolt (1a) and push back the junction unit as far asnecessary to disconnect the electrical connections (1b).767For precise identification ofthe electrical connections, see Wiring Diagrams Section.2. Remove the junction unit.2010592
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Unscrew bolt (1a) and open fuse access cover (1b).2. Undo the bolt (2a) and remove the integrated multiservices unit(2b) after having disconnected the electrical connections (2c),(2d), (2e), (2f) and (2g).2010595
5505A29
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b) for theadditional junction unit.2071293
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314864-5530B54battery cover - r+r . Make sure that the ignition key is in theOFF position.1. Disconnect the battery negative and positive terminals.2. Undo the bolt (2a) fixing the battery retaining bracket (2b).3. Remove the battery.2010647
5530B40
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314864-5530B54battery cover - r+r1. Press and release the retainers (1a), then remove the cover (1b)for the supply box on the battery. 2071303
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Working in the luggage compartment, undo the knob for the batterycover.2. Remove the battery cover.2010650
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213315016-7005E38front side door interiorhandle-r r1. Unscrew retaining bolts (1a) and remove switch unit protectivecover (1b).2. Apply slight pressure to switches (2a) and push sideways usingtool (2b) to separate the printed circuit complete with switches(2c) from the three retaining pins on the grip and from the retainersinside the switch unit.2010790
7005M12
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213315016-7005E38front side door interiorhandle-r r1. Prise the switch out of its housing and press the switch in fromthe outside to remove.2010791
7005M20
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21- 7005A04 front side door waterguard protection - r r or replace with door panel removed 1. With the window fully raised, arrange a device to support thewindow in raised position.2. Unscrew the nuts retaining the window bracket.3. Unscrew the nuts retaining the slide bracket.4. Unscrew the window motor retaining bolts.5. Adjust the electrically-operated window until the window isclosed, disconnect the window motor electrical connection.6. Remove the electrically-operated window from the door compartment.2010792
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21- 7005A04 front side door waterguard protection - r r or replace with door panel removed Open and close the windows a few timesto check for adjustment defects (window does not quite reach the topor the rear door pillar).1. With the window fully raised, loosen both nuts retaining theelectrically-operated window device to the window.2. Place the window in the correct closure position by hand (windowreaches top and rear edges).3. Operate the window device electrically, fit it against the glassand tighten the retaining bolts.2010793
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition keyis in tthe OFF position, then disconnect the battery negative terminal.1. Undo the bolts (1a) and remove the right and left trims (1b).2010794
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213315088-7010E38rear side door interiorhandle-r r1. Prise the electrically-operated window switch out of the grab handle.2010836
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213315044-7010A04rear side door waterguard protection - r r or arrange with door panel removed1. Unscrew the nuts retaining the electrically-operated windowdevice to the door.2. Undo the clip retaining the window to to the electrically-operatedwindow device and remove the plastic pin.3. With the window fully raised, position a support hook to preventaccidental lowering of the window.4. Disconnect the electrical connection.4. Lower the device manually until it can be removed from the doorcompartment.2010837
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213315044-7010A04rear side door waterguard protection - r r or arrange with door panel removed1. Check the electrically-operated window device nuts are tightenedto the specified torque.2. Check the fastening anchorage clip and plastic pin are properlypositioned and secured.Check the device is working properlyby raising and lowering the window. 2010838
