SCHEMA ELETTRICO - TRIP COMPUTER - Fiat BRAVO 1.9 JTD 16v
COMPONENTI - TRIP COMPUTER - Fiat BRAVO 1.9 JTD 16v
Codice componenti | Denominazione | Riferimento all’operazione |
B002 | CENTRALINA DI DERIVAZIONE SOTTO PLANCIA | |
B099 | SCATOLA MAXI FUSE SU BATTERIA | - |
C038 | MASSA SU TUNNEL CENTRALE | - |
E050 | QUADRO STRUMENTI | |
H001 | COMMUTATORE DI ACCENSIONE | |
H005 | DEVIOGUIDA | |
H090 | GRUPPO COMANDI INTERRUTTORI | |
M001 | BODY COMPUTER | |
M050 | CENTRALINA ABS | |
N040 | ELETTROPOMPA COMBUSTIBILE E MISURATORE DI LIVELLO |
LOCALIZZAZIONE COMPONENTI - TRIP COMPUTER - Fiat BRAVO 1.9 JTD 16v
Codice componenti | Denominazione | Riferimento all’operazione |
B002 | CENTRALINA DI DERIVAZIONE SOTTO PLANCIA | |
B099 | SCATOLA MAXI FUSE SU BATTERIA | - |
C038 | MASSA SU TUNNEL CENTRALE | - |
E050 | QUADRO STRUMENTI | |
H001 | COMMUTATORE DI ACCENSIONE | |
H005 | DEVIOGUIDA | |
H090 | GRUPPO COMANDI INTERRUTTORI | |
M001 | BODY COMPUTER | |
M050 | CENTRALINA ABS | |
N040 | ELETTROPOMPA COMBUSTIBILE E MISURATORE DI LIVELLO |
DESCRIZIONE - TRIP COMPUTER - Fiat BRAVO 1.9 JTD 16v
Il Trip Computer permette di visualizzare sul display del quadro di bordo le grandezze relative al tragitto, al consumo e alle percorrenze dalla vettura.Sono previste due modalita di Trip Computer (A e B) completamente indipendenti tra loro, la cui visualizzazione su display e attivabile tramite la pressione del pulsante “TRIP, posto sulla leva destra del devioguida.La modalita di visualizzazione su display dei dati segue un ordine prefissato:TRIP A:- Autonomia- Distanza percorsa- Consumo medio- Consumo istantaneo- Velocita media- Tempo di viaggioTRIP B:- Distanza percorsa- Consumo medio- Velocita media- Tempo di percorrenzaEntrambe le funzioni sono azzerabili (reset - inizio di una nuova missione).Il “Trip B” e una funzione escludibile, tramite il "Menu di Setup" del quadro strumenti.Per maggiori dettagliIl calcolo dei dati del Trip Computer viene effettuato all''interno del quadro strumenti.Il quadro strumenti e un nodo della rete CAN attraverso la quale scambia informazioni con il Body Computer e le altre unita elettroniche.Nel presente schema viene illustrato il funzionamento di quelle funzioni relative al quadro strumenti che hanno influenza anche sul Trip Computer.
DESCRIZIONE FUNZIONALE - TRIP COMPUTER - Fiat BRAVO 1.9 JTD 16v
L''alimentazione sotto chiave (INT) del quadro strumenti E50 giunge al pin 3 dal Body Computer M1 attraverso la linea fusibile F37 della centralina sottoplancia B2.L''alimentazione diretta giunge al pin 2 dal Body Computer M1 attraverso la linea fusibile F53 della centralina sottoplancia B2.Il pin 1 e a massa.Il Body Computer M1 e alimentato direttamente dalla batteria dalla linea protetta dal maxifuse d B99 al pin 18 del connettore F di interfaccia con la centralina sottoplancia B2; la alimentazione sotto chiave (INT) giunge al pin 9 del connettore F di interfaccia con la centralina B2.Il quadro strumenti E50 si collega dai pin 5 e 6 con il Body Computer M1 e tramite questo con tutta le rete CAN: via CAN giunge - tra gli altri - il segnale per il tachimetro elettronico (proveniente dalla centralina ABS M50).La centralina ABS M50 invia ianche un segnale tachimetrico discreto (VSO) al pin 10 del connettore A di M1Il contagiri elettronico riceve invece il segnale di giri motore proveniente via CAN dalla centralina di gestione del motore M10.L''indicatore livello carburante viene comandato secondo i segnali provenienti dal misuratore di livello collocato nel gruppo dell''elettropompa combustibile N40 - ai pin 7 (segnale) e 21 (massa) del connettore D del Body Computer M1, e da qui via CAN al quadro strumenti E50.Attraverso questi segnali il modulo elettronico TRIP elabora le informazioni di consumo istantaneo e medio, autonomia, velocita media, Km percorsi, durata ecc.Il pulsante "TRIP" di azzeramento del Trip Computer, collocato nel devioguida H5, invia un segnale di massa al pin 9 di E50.I comandi "MODE" "+" e "-" sono collocati sul gruppo di comandi al centro della plancia, lato sinistro H90B.Al pin 1 di H90B giunge dal pin 36 del connettore G di M1 la massa di riferimento.; dai comandi sono inviati segnali analogici al quadro strumenti, ai pin 13 e 16 di E50.