WIRING DIAGRAM - COMPRESSOR ENGAGEMENT - Fiat BRAVO 1.4 16v
COMPONENTS - COMPRESSOR ENGAGEMENT - Fiat BRAVO 1.4 16v
Component code | Description | Reference to the operation |
B001 | JUNCTION UNIT | |
B002 | JUNCTION UNIT UNDER DASHBOARD | |
B099 | MAXI FUSE BOX ON BATTERY | - |
C010 | LEFT FRONT EARTH | - |
C016 | AIR CONDITIONING UNIT EARTH | - |
C038 | EARTH ON CENTRE TUNNEL | - |
C039 | COMPRESSOR EARTH | - |
D004 | FRONT/ENGINE COUPLING | - |
D008 | AIR CONDITIONING-HEATER FRONT COUPLING | - |
H001 | IGNITION SWITCH | |
H080 | AIR CONDITIONING CONTROLS | |
H081 | CLIMATE CONTROL FAN CONTROL | |
J034 | PASSENGER COMPARTMENT AIR FAN SPEED RELAY 1 | - |
K086 | FROST SENSOR | - |
K120 | LINEAR SENSOR FOR FANS | |
L020 | AIR CONDITIONING COMPRESSOR ENGAGEMENT ELECTRO-MAGNET | |
M001 | BODY COMPUTER | |
M010 | ENGINE MANAGEMENT ECU | |
M070 | CLIMATE CONTROL SYSTEM CONTROL UNIT | |
N085 | PASSENGER COMPARTMENT AIR FAN | |
O030 | PASSENGER COMPARTMENT AIR FAN ADJUSTMENT RESISTOR |
COMPONENT LOCATION - COMPRESSOR ENGAGEMENT - Fiat BRAVO 1.4 16v
Component code | Description | Reference to the operation |
B001 | JUNCTION UNIT | |
B002 | JUNCTION UNIT UNDER DASHBOARD | |
B099 | MAXI FUSE BOX ON BATTERY | - |
C010 | LEFT FRONT EARTH | - |
C016 | AIR CONDITIONING UNIT EARTH | - |
C038 | EARTH ON CENTRE TUNNEL | - |
C039 | COMPRESSOR EARTH | - |
D004 | FRONT/ENGINE COUPLING | - |
D008 | AIR CONDITIONING-HEATER FRONT COUPLING | - |
H001 | IGNITION SWITCH | |
H080 | AIR CONDITIONING CONTROLS | |
H081 | CLIMATE CONTROL FAN CONTROL | |
J034 | PASSENGER COMPARTMENT AIR FAN SPEED RELAY 1 | - |
K086 | FROST SENSOR | - |
K120 | LINEAR SENSOR FOR FANS | |
L020 | AIR CONDITIONING COMPRESSOR ENGAGEMENT ELECTRO-MAGNET | |
M001 | BODY COMPUTER | |
M010 | ENGINE MANAGEMENT ECU | |
M070 | CLIMATE CONTROL SYSTEM CONTROL UNIT | |
N085 | PASSENGER COMPARTMENT AIR FAN | |
O030 | PASSENGER COMPARTMENT AIR FAN ADJUSTMENT RESISTOR |
DESCRIPTION - COMPRESSOR ENGAGEMENT - Fiat BRAVO 1.4 16v
The special button (ice symbol) on the climate control system control unit switches on the air cooling and dehumidification circuit, activating the air conditioning compressor.The above button enables the operation of the air cooling circuit, but the actual compressor activation is also dependent upon the activation of:- the fan linear sensor, located on the coolant circuit that locks air conditioner activation if coolant pressure is too low or high;- the frost thermostat sensor, located near the evaporator, which stops the engagement of the air conditioning if the temperature of the evaporator is too low;- the engine control unit that excludes compressor operation in accordance with engine management mode; e.g. in the case of high engine temperatures or high engine load (sudden acceleration);Automatic climate control: If the compressor is enabled and the engine started, the control unit that controls the manual ventilation does not go below a minimum value.Manual climate control: when the compressor is activated, the fan is also driven at first speed via a relay located inside the unit.For more detailsThe supply circuit for the compressor is controlled by a specific relay and protected by a special fuse, both located in the engine compartment junction unit.The fan receives a power supply from a line protected by a special fuse and operated by a specific relay in the engine compartment junction unit.The controls receive a power supply from an ignition-controlled line protected by a fuse in the junction unit under the dashboard.
FUNCTIONAL DESCRIPTION - COMPRESSOR ENGAGEMENT - Fiat BRAVO 1.4 16v
The relay T5 for the engine compartment junction unit B1 controls the compressor engagement circuit.The supply for the relay via the line for specific fuse F19 of the engine compartment junction unit B1.The power supply for the coil for relay T5 arrives from the main injection relay T9 and from the ignition-operated line (15/54) protected by fuse F16, both located in the engine compartment junction unit B1.Automatic climate control:The climate control system control unit M70 - from pin 4 of connector C - sends the enablement signal for the engagement of the compressor to the engine management control unit M10, pin 40 of connector A.Manual climate control:When the unit button H80 is pressed, two signals are sent:- one signal to the frost electronic thermostat K86 which, if the temperature of the evaporator is not too low, "resends" it to the engine management control unit M10, pin 40 of connector A.- a second signal excites the coil of relay J34, which controls activation of the first speed of air fan N85, as describedFan N85 - supplied by the ignition-operated line (INT/A) of relay T8 and specific fuse F8 of engine compartment control unit B1 is operated at first speed if the compressor activation request button is pressed, even if control knob H81 is in position "0".On the basis of its internal control logic, the control unit M10 sends the command - from pin 46 of connector A - to engage the compressor which energizes the relay T5 so that the air conditioning compressor engagement solenoid L20 is operated at a voltage of 12 V.If the linear sensor for the fans K120 signal to the control unit M10 - pin 54 of connector B - that the pressure value is too high or too low, then the control unit M10 excludes the engagement of the compressor.The linear sensor K120 receives a power supply and reference earth from the engine management control unit M10, pin 53 and 3 of connector A.