Schema elettrico - REGOLATORE ASSETTO FARI - Fiat MULTIPLA 1.6 16v fino a 05/99
COMPONENTI - REGOLATORE ASSETTO FARI - Fiat MULTIPLA 1.6 16v fino a 05/99
Codice componente | Denominazione | Riferimento al complessivo |
B1 | Centralina di derivazione | |
B5 | Scatola MAXI FUSE | |
C10 | Massa ant. sinistra | - |
C11 | Massa ant. destra | - |
C15 | Massa plancia lato guida | - |
C20 | Massa plancia lato passeggero | - |
D1 | Giunzione ant./plancia | - |
H1 | Commutatore di accensione | |
H5 | Devioguida | |
H15 | Comando assetto proiettori | |
J45 | Teleruttore mantenimento anabbaglianti | - |
F10 | Proiettore sinistro | |
F11 | Proiettore destro |
Localizzazione componenti - REGOLATORE ASSETTO FARI - Fiat MULTIPLA 1.6 16v fino a 05/99
COMPONENTI - REGOLATORE ASSETTO FARI - Fiat MULTIPLA 1.6 16v fino a 05/99
Codice componente | Denominazione | Riferimento al complessivo |
B1 | Centralina di derivazione | |
B5 | Scatola MAXI FUSE | |
C10 | Massa ant. sinistra | - |
C11 | Massa ant. destra | - |
C15 | Massa plancia lato guida | - |
C20 | Massa plancia lato passeggero | - |
D1 | Giunzione ant./plancia | - |
H1 | Commutatore di accensione | |
H5 | Devioguida | |
H15 | Comando assetto proiettori | |
J45 | Teleruttore mantenimento anabbaglianti | - |
F10 | Proiettore sinistro | |
F11 | Proiettore destro |
Descrizione - REGOLATORE ASSETTO FARI - Fiat MULTIPLA 1.6 16v fino a 05/99
La vettura permette di regolare direttamente dal posto guida l'orientamento del fascio luminoso dei proiettori in base al carico. In questo modo si ottiene rapidamente il corretto orientamento dei fari. Il dispositivo di regolazione consiste in un motorino montato su ciascuno dei due proiettori anabbaglianti che li inclina opportunamente, in modo da abbassare il fascio luminoso nel caso di vettura particolarmente carica, e di alzarlo invece quando il carico diminuisce.
Descrizione funzionale - REGOLATORE ASSETTO FARI - Fiat MULTIPLA 1.6 16v fino a 05/99
Il dispositivo comando assetto fari H15 e alimentato al pin 2 - a luci anabbaglianti inserite - da una linea proveniente dal devioguida H5 : si tratta di una alimentazione sotto chiave (INT/A) della linea protetta dal fusibile F5 della centralina di derivazione B1 , tramite il teleruttore apposito J45 . Il pin 4 del dispositivo H15 e a massa, mentre dal pin 1 esce il segnale che giunge ai pin 7 dei proiettori F10 (sinistro) e F11 (destro, ottenuto attraverso un partitore resistivo che fa variare la tensione in uscita a seconda delle quattro posizioni selezionabili. I motorini collocati nei dei proiettori F10 (sinistro) e F11 (destro) sono alimentati, ai pin 3, ai pin 6 di F10 e F11 dalla stessa linea del circuito delle luci anabbaglianti, linea protetta dal fusibile F5 della centralina di derivazione B1 . Il dispositivo funziona pertanto solo ad anabbaglianti inseriti.