DescriptionThe Cruise Control function - constant speed regulator - allows the car to be driven at a constant speed without pressing the accelerator pedal. The function is managed by the engine control unit which receives the commands from the special Cruise Control lever on the left of the steering wheel, under the steering column switch unit.The function is switched on by turning the ring nut (ON).When a speed is set (SET +, SET -) it remains memorized and can be recalled at any time (RCL).The function is automatically switched off:by pressing the brake pedal;by pressing the clutch pedal;by turning the ring nut to OFF;by turning off the engine;In these cases the last speed reached is memorized, and can be recalled by pressing the RCL button.The system also switches off at vehicle speeds below the permitted minimum (about 30 km/h)When the function is switched on, the relevant warning light on the instrument panel, connected via the CAN network to the engine management control unit, comes on. For more details Characteristic of working principle 5580A cruise control system
Functional description The Cruise Control function is controlled by engine management unit M10 upon a command from the Cruise Control switch H7 located to the left of the steering wheel. The switch H7 is supplied when the ignition is switched on (INT) - pin 2 - from the line protected by the fuse F35 of the unit under the dashboard B2 . Control H7 is connected to management unit M10:to pin 58 of connector A, with the ON/OFF signalto pin 41 of connector A, with the RESUME signalto pin 8 of connector A, with the SET + signalto pin 9 of connector A, with the SET - signal To control the Cruise Control function, control unit M10 also uses 'pedal released' signals (N.C. contact) coming from the second contact for the brake lights switch I30 and a signal from clutch switch I31. 3360979SeeE5030PETROL ENGINE ELECTRONIC MANAGEMENT Via the CAN line, the engine control unit M10 is connected to the Body Computer M1 and the instrument panel E50 , to manage the 'Cruise Control on' warning light.
0Removing201Refitting21Disconnect the negative battery terminal.1. Remove the junction unit protective cover.192009560
5505A35
0Removing201Refitting213363098-5530B56BATTERY DRIP TRAY COVER- R.R.Disconnect the battery negative terminal.3363361-7040A44facia lh side cover - r r1. Disconnect the front electrical connectors of the junction unitcomplete with body computer.2. Unscrew the retaining bolts.3. Remove from its seating the junction unit complete with bodycomputer.4. Disconnect the rear electrical connectors of the junction unitcomplete with body computer.2027438
5505A36
0Removing201Refitting211. Separate the junction unit (1a) from the body computer (1b),by releasing the retaining lugs (1c).2027440
5505A41
0Removing201Refitting213363098-5530B56BATTERY DRIP TRAY COVER- R.R.Disconnect the battery negative terminal.3363151-5580C18air bag module - r+r . 769- 4110A16 steering wheel - r r for replacement or checks forversions with airbag and manual gearbox with hydraulic selection . 1. Disconnect the electrical connectors (1a) and remove the controlunit (1b) from its seating.2027441
0Removing201Refitting213363098-5530B56BATTERY DRIP TRAY COVER- R.R.1. Release the clips and remove the protective cover for the uniton the battery.2. Undo the bolts (2a) and remove the battery fixing bracket (2b).3. Slacken the nut and disconnect the battery's negative terminal.2027495
5530B52
0Removing201Refitting21Op. 5530B56 BATTERY DRIP TRAY COVER - R.R.3363098Op. 5530B10 BATTERY - R+R3363096- Disconnect the engine management unit electrical connections.Release the wiring from the retaining bands.1. Undo the rear fixing bolt (1a), release the front fastenings (1b) and place the engine compartment junction unit (1c) at the side.192008351
5530B56
0Removing201Refitting211. Undo the fixing bolts (1a) and remove the battery cover (1b).2027502
0Removing201Refitting213363098-5530B56BATTERY DRIP TRAY COVER- R.R.Disconnect the battery negative terminal.3363357-7040A26steering column trim - r+r1. Undo the bolts fixing the analogue instrument panel trim.2. Remove the trim under the instrument panel.3. Undo the upper bolts fixing the instrument panel to the dashboard;then partly release the panel.2027547
767 It is not possible toorder a single lock barrel or to order barrels using a single partcode. When ordering barrels, observe the special procedure illustrated 3363161See assembly5580E anti-theft device .
0Removing201Refitting21Disconnect the negative battery terminal.1. Disconnect the electrical connection for the PDA electropneumatic valve.2. Disconnect the two vacuum pipes from the PDA electropneumatic valve.3. Remove the PDA electropneumatic valve.192007968
1056B33
0Removing201Refitting21Disconnect the negative battery terminal.1. Disconnect the electrical connection for the PDA position sensor.2. Undo the retaining bolts (2a) and remove the PDA position sensor (2b).192007970
0Removing201Refitting213363098-5530B56BATTERY DRIP TRAY COVER - R.R. . Disconnect the battery negative terminal.Remove the injection wiring from the area.1. Disconnect the electrical connector for the sender unit.2. Undo and remove the sender unit.2024995
0Removing201Refitting21Op. 5530B56 BATTERY DRIP TRAY COVER - R.R.3363098.Disconnect the negative battery terminal.1. Disconnect the electrical connection for the sensor.2. Undo the fixing bolt (2a) and remove the sensor (2b).192007915
1056B56
0Removing201Refitting21Disconnect the battery negative terminal.1. Disconnect the electrical connection from the engine idle speedself-adjustment motor.2. Undo the bolts (2a) and remove the engine idle speed self-adjustmentmotor (2b).2025359
0Removing201Refitting21Discharge the fuel pressure using the toolconnected to the valve on the fuel manifold pipe.1. Disconnect the rapid attachment for the fuel supply pipe andrelease the latter from the fixing band.2025196
0Removing201Refitting213363098-5530B56BATTERY DRIP TRAY COVER - R.R.Disconnect the battery negative terminal.1. Remove the clip securing the injector to the fuel manifold.2. Remove the injector from its seat.3. Remove the injector seals2025001
The manual procedure and the teser procedurefor re-initalising the electronic ignition/injection control unit isshown below.767When the car is first started,carry out the following operations whenever the throttle body or enginemanagement unit is replaced.769Procedure using testerMake sure that the ignition key is in theOFF position.Connect the tool to the tester input andplace the knob in position 3.Connect the Examiner diagnostic equipment.Turn the ignition key to ON position (engineoff).Wait for the test to be run on the throttlebody, when the tester will confirm that Turn the ignition key to the OFF position.Using the Examiner, check that the self-learningof idle speed has finished correctly ( LOWER THROTTLE BED SELFLEARNING-completed)767If the self-learning procedureis not correct, turn the ignition off (STOP position) and repeatthe above procecure. If the incorrectness continues, check thatthe diagnostic cable connection is secure and that the instrumentis working.Manual procedureTurn the ignition key to ON position (engineoff)Wait 60 seconds, the time required forthe control unit to check the throttle body's internal spring andthe butterfly's maximum/minimum angles.Turn the ignition key to the OFF positionWait 10 seconds, the time required forthe control unit to save the learnt values in EPROM.767After carrying out initialisation,the engine control unit may be deactivated (battery disconnection)without losing data.
1056B82
0Removing201Refitting213363098-5530B56BATTERY DRIP TRAY COVER - R.R. . Disconnect the battery negative terminal.1. Disconnect the electrical connections (1a) for the injectioncontrol unit (1b) using the lever (1c).2. Undo the fixing bolt (2a) and disconnect the control unit earthlead (2b).3. Undo the fixing nuts (3a) and remove the injection control unit(3b) from support (3b).2025002
0Removing201Refitting21Position the vehicle on a lift. 1016A10 COPERCHIO INSONORIZZANTE - S.R.3355014Op. 5530B56 BATTERY DRIP TRAY COVER - R.R.3363098Disconnect the negative battery terminal.Op. 7055B54 UNDER ENGINE PROTECTION/GUARD - R.R.33634881. Undo the nuts (1a) and move the cable duct protection (1b).2. Disconnect the electrical connection for the rpm sensor.3. Disconnect the electrical connection for the detonation sensor.4. Disconnect the electrical connection for the engine oil pressure warning light switch.5. Disconnect the electrical connection for the starter motor.6. Disconnect the electrical connection for the alternator.192007933
0Removing201Refitting213363098-5530B56BATTERY DRIP TRAY COVER - R.R.Disconnect the battery negative terminal.1. Disconnect the water temperature sensor electrical connection.2. Undo the thermostat water temperatur sensor and remove.2025763
0Removing201Refitting21Place the car on a ramp.3363098-5530B56BATTERY DRIP TRAY COVER - R.R.Disconnect the battery negative terminal.1. Disconnect the electrical connection for the rpm sensor.2. Undo bolts (2a) and remove rpm and timing sensor (2b).2025765
0Removing201Refitting213362539-1016A10sound-proofing cover - r + r1. Disconnect the solenoid electrical connection on the vacuum tankfor the throttle body pneumatic valve.2. Disconnect the vacuum pipe from the solenoid on the vacuum tankfor the throttle body pneumatic valve.3. Unscrew the bolt securing the pneumatic valve4. Remove the solenoid for the pneumatic valve on the vacuum tank.2025773
0Removing201Refitting213363098-5530B56BATTERY DRIP TRAY COVER - R.R.Disconnect the battery negative terminal.1. Disconnect the electrical connection from the injection electroniccontrol unit.2. Undo nut (2a) and release earth lead (2b).3. Undo the retaining bolts.4. Remove the engine management control unit from its housing.2025774
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.