Componenti - LUCI FENDINEBBIA - Fiat ULYSSE 2.0 16V JTD da 04/03
Codice componente | Denominazione | Riferimento al complessivo |
A001 | BATTERIA | - |
B001 | CENTRALINA DI DERIVAZIONE VANO MOTORE | |
C010 | MASSA ANTERIORE SINISTRA | - |
C011 | MASSA ANTERIORE DESTRA | - |
C015 | MASSA PLANCIA LATO GUIDA | - |
C020 | MASSA PLANCIA LATO PASSEGGERO | - |
D006 | GIUNZIONE ANTERIORE/POSTERIORE | - |
D020 | GIUNZIONE PLANCIA / POSTERIORE | - |
E050 | QUADRO STRUMENTI | |
F010 | PROIETTORE SINISTRO | |
F011 | PROIETTORE DESTRO | |
H001 | COMMUTATORE DI ACCENSIONE | |
M001 | BODY COMPUTER | |
M093 | CENTRALINA NODO VOLANTE (NVO) | |
M140 | CENTRALINA SPIE E ODOMETRO (NSO) | - |
Codice componente | Denominazione | Riferimento al complessivo |
A001 | BATTERIA | - |
B001 | CENTRALINA DI DERIVAZIONE VANO MOTORE | |
C010 | MASSA ANTERIORE SINISTRA | - |
C011 | MASSA ANTERIORE DESTRA | - |
C015 | MASSA PLANCIA LATO GUIDA | - |
C020 | MASSA PLANCIA LATO PASSEGGERO | - |
D006 | GIUNZIONE ANTERIORE/POSTERIORE | - |
D020 | GIUNZIONE PLANCIA / POSTERIORE | - |
E050 | QUADRO STRUMENTI | |
F010 | PROIETTORE SINISTRO | |
F011 | PROIETTORE DESTRO | |
H001 | COMMUTATORE DI ACCENSIONE | |
M001 | BODY COMPUTER | |
M093 | CENTRALINA NODO VOLANTE (NVO) | |
M140 | CENTRALINA SPIE E ODOMETRO (NSO) | - |
La vettura puo essere dotata di due luci supplementari “fendinebbia” posizionate nei proiettori anteriori.Le luci fendinebbia sono attivate attraverso il relativo comando a ghiera sul devioguida (centralina nodo volante): a luci inserite e prevista l’accensione della spia relativa sul quadro strumenti.L’attivazione delle luci fendinebbia viene gestita dal Body Computer mentre il comando viene realizzato dalla centralina di derivazione vano motore.Affinche le luci fendinebbia siano attivate, il Body computer deve ricevere come input i seguenti segnali:- consenso di chiave su M;- comando dalla ghiera del devioguida;- luci di posizione inserite.Se le luci di posizione vengono disattivate, verranno disinseriti anche i fendinebbia: questa operazione viene effettuata anche se la ghiera e gia ruotata. Viceversa, se le luci di posizione vengono nuovamente inserite, anche i fendinebbia si riattiveranno.Se al chiave viene portata nella posizione S e successivamente riportata su M, per inserire le luci fendinebbia, si dovra nuovamente azionare la ghiera sul devioguida.
Il comando di inserimento luci fendinebbia viene fornito dalla centralina Nodo volante M093 tramite linea CAN (pin 1 e 3 del connettore A) al Nodo body computer M001 (sui pin 5 e 3 del connettore G rispettivamente).La centralina Nodo volante M093 e collegata alla massa C015 (connettore A) tramite il pin 4 del connettore A, ed e alimentata da due linee: una, dal pin 11 del connettore B del Nodo body computer M001 al pin 5 del connettore A; l’altra, dal pin 1 del connettore G di M001 al pin 4 del connettore D, protetta dal fusibile F04.A sua volta, il Nodo body computer M001 informa, attraverso linea CAN (pin 25 e 27 del connettore E), la centralina di derivazione vano motore B001 (pin 12 e 11 rispettivamente del connettore F) dell’avvenuta richiesta di inserimento luci fendinebbia.La centralina di derivazione vano motore B001, tramite i pin 24 e 13 del connettore G, va ad alimentare (rispettivamente) i pin 6 dei proiettori anteriori sinistro F010 e destro F011.L’accensione delle apposite spie viene gestita dal Nodo spie odometro M140, che comunica tramite rete CAN (pin 2 e 5) con il quadro strumenti E050 (pin 6 e 12) e il Nodo body computer M001 (pin 8 e 10 connettore D).Il Nodo body computer M001, tramite il pin 6 del connettore D, alimenta il Nodo spie odometro M140 sul pin 4 e il quadro strumenti E050 sul pin 13. Questa linea e protetta dal fusibile F14.