Schaltplan - EINSTELLUNG DER AUSSENSPIEGEL - Fiat ULYSSE 2.0 16v da 04/03
Bauteile - EINSTELLUNG DER AUSSENSPIEGEL - Fiat ULYSSE 2.0 16v da 04/03
Bauteil-Nr. | Bezeichnung | Bezug zur Baugruppe |
B001 | Verteiler im Motorraum | 5505A |
C020 | Masse Armaturenbrett Beifahrerseite | - |
C031 | Masse hinten rechts | - |
D030 | Verbindung Vordertur links | - |
D031 | Verbindung Vordertur rechts | - |
D042 | Verbindung Deckenleuchten | - |
D070 | Verbindung Fahrersitz | - |
H051 | Bediengruppe Fensterheber und Au?enspiegel auf der Fahrertur | 7005M |
M001 | Body Computer | 5505A |
M066 | Turbedienelektronik Fahrerseite (NPG) | 5505A |
M067 | Turbedienelektronik Beifahrerseite (NPP) | - |
P060 | Linker Au?enspiegel | 7005R |
P061 | Rechter Au?enspiegel | 7005R |
P065 | Elektrochromatischer Innenruckspiegel | 7065C |
Einbaulage Bauteile - EINSTELLUNG DER AUSSENSPIEGEL - Fiat ULYSSE 2.0 16v da 04/03
Bauteile - EINSTELLUNG DER AUSSENSPIEGEL - Fiat ULYSSE 2.0 16v da 04/03
Bauteil-Nr. | Bezeichnung | Bezug zur Baugruppe |
B001 | Verteiler im Motorraum | 5505A |
C020 | Masse Armaturenbrett Beifahrerseite | - |
C031 | Masse hinten rechts | - |
D030 | Verbindung Vordertur links | - |
D031 | Verbindung Vordertur rechts | - |
D042 | Verbindung Deckenleuchten | - |
D070 | Verbindung Fahrersitz | - |
H051 | Bediengruppe Fensterheber und Au?enspiegel auf der Fahrertur | 7005M |
M001 | Body Computer | 5505A |
M066 | Turbedienelektronik Fahrerseite (NPG) | 5505A |
M067 | Turbedienelektronik Beifahrerseite (NPP) | - |
P060 | Linker Au?enspiegel | 7005R |
P061 | Rechter Au?enspiegel | 7005R |
P065 | Elektrochromatischer Innenruckspiegel | 7065C |
Beschreibung - EINSTELLUNG DER AUSSENSPIEGEL - Fiat ULYSSE 2.0 16v da 04/03
Die Au?enspiegel konnen uber einen Joystick, der sich im Bedienfeld auf der Fahrertur befindet, elektrisch in die beiden Richtungen verstellt werden.Das Ausrichten beider Spiegel erfolgt uber einen "Joystick", der in vier Richtungen bewegt werden kann: zuerst wird der zu verstellende Spiegel (rechts oder links) gewahlt, anschlie?end wird mit den nachfolgenden Drehungen der gewahlte Spiegel eingestellt.Wird der Joystick um etwa 120° zuruckgedreht, dann werden die Au?enspiegel eingeklappt. Durch Drehen in die andere Richtung werden die Spiegel ausgeklappt.Der Joystick betatigt drei E-Motoren in den zwei Spiegeln: ein Motor erlaubt die Drehung des Spiegels um die waagerechte Achse, der andere um die senkrechte Achse, der dritte steuert das Einklappen.Die Au?enspiegel werden durch die Turelektroniken gem. der uber CAN-Netz vom Body Computer ubertragenen Kontrolllogik.Das Einstellen der Au?enspiegel ist nur mit dem Zundschalter auf M moglich.Der Innenruckspiegel ist elektrochromatisch: er enthalt eine elektronische Einrichtung, die das automatische Abblenden des Spiegels steuert.Den Automatikbetrieb erhalt man, wenn die Taste am Spiegel gedruckt wird. Eine LED zeigt das erfolgte Einschalten an.Um bei Fahrmanovern die beste Sicht zu gewahrleisten, schaltet der Innenspiegel auf Automatik, wenn der RG eingelegt wird.Bei den Versionen "Sitze mit Speicher" konnen zusatzlich zu manuellen Verstellung der Au?enspiegel 4 Stellungen gespeichert werden:Diese komplexe Logik wird von der Elektronik Sitze/Spiegel mit Speicher verwaltet, die uber das CAN-Netz mit dem Body Computer kommuniziert [EL3076].
Funktionsbeschreibung - EINSTELLUNG DER AUSSENSPIEGEL - Fiat ULYSSE 2.0 16v da 04/03
Die Turknoten M066 und M067 werden vom Knoten Body Computer an Pin 16 des Steckers A uber die Leitung mit der Sicherung F09 mit Strom versorgt.Die Turknoten M066 und M067 erhalten die Stromversorgung uber CAN (Pin 1 des Steckers A) von der durch die Sicherung F04 im Body Computer geschutzte Leitung.Der Knoten Body Computer kommuniziert auch uber das CAN-Netz mit den Turknoten M066 und M067, und zwar von den Pins 21, 23 und 24, 26 des Steckers L zu den Pins 14 und 3 des Steckers A des Knoten Fahrertur M066 und des Knoten Beifahrertur M067.Die beiden Turknoten M066 und M067 steuern direkt die E-Motoren der entsprechenden Au?enspiegel P060 und P061 an.Der Befehl zum Verstellen kommt von der Baugruppe H051, wo sich die drei speziellen Schalter befinden: einer zur Auswahl des Au?enspiegels (rechts oder links), einer zur Spiegeleinstellung und einer zum Einklappen des Spiegels.Von Pin 15 des Steckers A versorgt der Turknoten M066 die Schaltergruppe H051. Die Auswahl des Au?enspiegels wird an Pin 10 des Steckers A von M066 gemeldet, die Einstellung wird durch das Signal gesteuert, das an Pin 6 des Steckers A von M066 gesendet wird.Zur Einstellung des rechten Spiegels kommuniziert der Turknoten M066 uber das CAN-Netz mit dem Knoten Beifahrertur M067.Die Turknoten M066 und M067 betatigen uber den Stecker B die Verstellmotoren der jeweiligen Au?enspiegel P060 und P061 an, wahrend von Stecker C die Einklappmotoren der Spiegel betatigt werden - Pin 2 und 3. Das Ruckmeldesignal der tatsachlichen Spiegelstellung wird an den Pins 1, 4, 5 und 6 empfangen.Immer wenn der RG eingelegt wird, schaltet sich der Innenspiegel P065 auf Automatikbetrieb um. Der RG-Schalter I020 - wenn eingeschaltet - liefert die Stromversorgung zum Spiegel P065 uber die mit der Sicherung F01 im Verteiler im Motorraum B001 abgesicherte Leitung.Der Spiegel P065 kann durch Drucken des entsprechenden Schalters am Spiegel selbst auch manuell aktiviert werden. In diesem Fall erfolgt die Stromversorgung vom Knoten Body Computer (Pin 12 des Steckers H) uber die Leitung mit der Sicherung F07 im Body Computer.Bei Versionen mit "Sitze mit Speicher" erfolgt die Verstellung der Spiegel hinsichtlich einer der 4 gespeicherten Stellungen mit den Informationen, die von der Elektronik Sitze/Spiegel mit Speicher M076 uber das CAN-Netz ubertragen werden.