Functional description The ignition-operated power supply (INT) of the instrument panel E50 reachespin 1 of connector A through the line of fuse F37 of the unit underthe dashboard B2 ; the direct supply reaches pin 2 of connectorA through the line of fuse F53 of the unit under the dashboard B2 ;pin 7 of connector A is earthed (earth controlled by the Body Computer M1 ). The instrument panel E50 is connectedfrom pins 3 and 4 of connector A to the Body Computer M1 and viathe latter to the whole CAN network: via CAN the signal for the electronicspeedometer arrives (coming from the ABS control unit M50): thissignal is replicated from pin 16 of M50 to pin 7 of connector Aof the Body Computer M1. The electronic rev counter receives therpm signal coming via CAN from the engine management control unit M10 . The fuel gauge is controlled in accordancewith the signals coming from the fuel gauge sender unit locatedin the fuel pump assembly N40 - at pins 4 and 15 of connectorD of the Body Computer M1, and from here via CAN to the instrumentpanel E50. The low brake fluid/handbrake applied warninglight comes on through a signal from the handbrake switch I40 ,which reaches pin 24 of connector E of the Body Computer M1 ,or from the signal from the low brake fluid level sensor K25 ,which reaches pin 18 of connector A of M1 . All these signals are transferred via CANto the instrument panel E50 . Instrument panel E50 also contains electronicmodules that control panel dimmed lighting and other controls SeeE2530 INSTRUMENT LIGHTING ,headlamp alignment adjustment and the robotized gearbox SeeE3080 HEADLAMP AGLINMENT CORRECTOR buzzer SeeE7051 ROBOTIZED GEARBOX . The TRIP function is shown in the relevantdiagram 2428031SeeE4080TRIP COMPUTER .
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b).2044997
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212429579-7040A30Left instrument panellower TRIM - R.R.1. Disconnect the electrical connections (1a, 1b, 1c, 1d, 1e, 1f).2. Undo the left-threaded bolt securing the facia trim mount beam.3. Undo the bolts securing the body computer/junction unit.4. Move facia trim (4a) slightly and move body computer/junctionunit (4b) downwards.5. Disconnect the electrical connections (5a, 5b, 5c).6. Recover the body computer/junction unit.2045005
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect electronic control unit electrical connections (1a),(1b), (1c).2. Undo the bolts.3. Recover the control unit2045007
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect electronic control unit electrical connections (1a),(1b), (1c).2. Undo the bolts.3. Recover the control unit2045008
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition key is in OFFposition, then disconnect the battery negative terminal (-).1. Disconnect the brake light switch electrical connection.2. Turn and remove the brake light switch.2045071
5550D16
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the tailgate.1. Prise up the rubber pads.2. Press the tail-light retainers in the arrowed direction and releasefrom the seat.2045072
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition key is in OFFposition, then disconnect the battery negative terminal (-).1. Disconnect the electrical connection from the reversing lightsswitch.2. Undo and remove the reversing lights switch.2045076
brake pump, reservoir and load proportioning valve
3330C30
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on theramp. Proceed with removal 2429398-5530B10battery - r+r . Proceed with removal 2429401-5530B52Battery DRIP TRAY/SUPPORT- R.R. . 1. Remove the protective cap on the brake caliper bleed valve.2. Connect the collection system (pipe and reservoir) to the bleedvalve on the brake caliper.3. Loosen the bleed valve on the brake caliperWait for the brake-clutch reservoir todrain.2044743
3330C40
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Undo the remove the brake fluid reservoir cap.2044745
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Proceed with removal 2429398-5530B10battery - r+r . Proceed with removal 2429401-5530B52Battery DRIP TRAY/SUPPORT- R.R. . 1. Remove the protective cap on the brake caliper bleed valve.2. Connect the collection system (pipe and reservoir) to the bleedvalve on the brake caliper.3. Loosen the bleed valve on the brake caliperWait for the brake-clutch reservoir todrain.2044760
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21.767The following procedure describesremoval/refitting of the left rear wheel rpm sensor; proceed asfor the right rear wheel rpm sensor.Position the vehicle on the ramp.Ensure that the ignition key is in OFFposition, then disconnect the battery negative terminal (-).1. Undo the bolt (1a) and remove the rear wheel rpm sensor (1b).2. Release the rear wheel rpm sensor electrical wiring from theattachments on the rear suspension.2044773
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on the ramp.Ensure that the ignition key is in OFFposition, then disconnect the battery negative terminal (-). Proceed with removal 2428909-1040A70submerged pump assemblycomplete with level guage control - r + r . Drain the fuel from the tank using suitableequipment and appropriate protection to meet current safety requirements. Proceed with removal 2429602-7040L22REAR TRIM on TUNNEL-R.R. . 1. Slacken the handbrake cable adjustment nut.2043722
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on the ramp. Proceed with removal 2429260-4450B08right rear wheel r r . Proceed with removal 2429680-7055B45right hand rear supplementarywheel arch - r+r . 1. Undo the bolt securing the fuel filler pipe to the body.2. Loosen the band (2a) and disconnect the fuel filler pipe (2b)from the tank.3. Loosen the band (3a) and disconnect return pipe (3b).4. Remove the sleeve joining the fuel filler pipe to the tank.2043732
1040A40
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Open the access flap to the fuel filler pipe cap.2. Remove pin (2a) and disconnect safety cable (2b) from the body.3. Undo and remove the fuel filler pipe cap.2043733
1040A70
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition key is in OFFposition, then disconnect the battery negative terminal (-).Lift the rear seat cushion lift the floorcovering to gain access to the fuel pump flap.1. Undo the bolts (1a) and remove the protective cover (1b).2. Disconnect the electrical connection from the fuel pump and level gauge.3. Disconnect the rapid attachment for the fuel supply pipe.4. Unscrew the ring nut (4a) using tool (4b).5. Remove the immersed pump assembly complete with gauge.2043736
1040A74
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition key is in OFFposition, then disconnect the battery negative terminal (-).1. Remove upper part of floor covering next to facia.2. Disconnect the electrical connection from the inertia switch.3. Undo retaining nuts (3a) and remove inertia switch (3b)2043737
Русский
