All Wiring Diagrams for Chevrolet Corvette 2008 model

AIR CONDITIONING

Automatic A/C Wiring Diagram (1 of 2) for Chevrolet Corvette 2008

List of elements for Automatic A/C Wiring Diagram (1 of 2) for Chevrolet Corvette 2008:

• (i/p harness, 39 cm from the hvac control module connector)
• A/c comp fuse 15 10a
• A/c comp relay 35
• A/c compressor clutch (right front of engine block)
• A/c off switch
• Bat
• Blower ctrl
• Blower speed switch
• Body control module (bcm) (mounted on toe board, in right footwell)
• Coolfan fuse 25 60a
• Defog rly ctrl
• Defogger system
• Defrost frost
• Defrost switch
• Dr ctrl a
• Dr ctrl b
• Drv htd st sig
• E1 x2
• F13
• F14
• G102 (on top of right frame rail, ground for sp102)
• G202 (at base of right "a" pillar)
• Gnd
• H13
• H14
• Hot at all times
• Hot w/ run/ crank relay energized
• Hvac control module (center of dash, under radio)
• Hvac fuse 28 40a
• Hvac/ pwr snd fuse 10a
• Ign
• Ign 1 voltage
• Interior lights system
• Isrvm/ hvac fuse 10a
• J102
• J216
• J231
• Lamp ctrl
• Left air temperature switch
• Light sens sig
• Logic
• Low ref
• Mirrors & shift interlock systems
• Mode ctrl
• Mode switch
• Mtr spd ctrl
• Off ctrl
• Pass htd st sig
• Pnk
• Powertrain ign 1 relay 44
• Recirc ctrl
• Recirculation switch
• Red
• Right air temperature switch
• Seats system
• Sens sig
• Serial data
• Speed ctrl
• Sply voltage
• Sply voltage 4
• Sunload sig
• Tan
• Temp ctrl
• Temp ctrl sig
• Underhood fuse block (on right side of engine compt)
• X1 c10
• X4 d8 pnk

Automatic A/C Wiring Diagram (2 of 2) for Chevrolet Corvette 2008

List of elements for Automatic A/C Wiring Diagram (2 of 2) for Chevrolet Corvette 2008:

• (behind right front fender, between wheelhouse & dash panel) engine control module (ecm)
• (front of engine compt, rear of radiator) fan control module
• (i/p harness, 35 cm from hvac control module connector)
• (rear of radiator)
• (top left side of dash) head up display (hud)
• 5v ref
• A/c refrigerant pressure sensor (on a/c high pressure line)
• Ambient air temperature sensor (on radiator support, at right front of engine)
• Aspirator blower motor
• Bat
• Blower motor control module
• Check gages
• Computer data lines system
• Coolant over temp engine hot/stop engine low coolant
• Engine coolant temperature (ect) sensor (in front left side of left cylinder head)
• Engine cooling fan
• G102 (on top of right frame rail, ground for sp102)
• G202 (at base of right "a" pillar)
• Gnd
• Hot engine-a/c off service a/c
• Hud class 2 serial data
• Hud message center
• Ign
• Ignition 1
• Inside air temperature sensor (right of steering column)
• Instrument panel cluster (ipc)
• Ipc class 2 serial data
• J242
• Left air temperature actuator (on left side of hvac module assembly)
• Logic
• Low ref
• Low ref x2 tan
• Lower left air temperature sensor (in left middle of hvac module)
• Lower right air temperature sensor (in right middle of hvac module)
• Message center
• Message request
• Mode actuator (right side of hvac module)
• Pnk
• Recirculation actuator (mounted to right side of blower motor assembly)
• Red
• Right air temperature actuator (on right side of hvac module assembly)
• Rly ctrl
• Sens sig
• Serial data +
• Serial data - x1 tan
• Speed ctrl
• Sunload sensor assembly (on top left center of dash)
• Tan
• Upper left air temperature sensor (in left center of dash, in hvac air flow duct)
• Upper right air temperature sensor (in upper right of dash, in hvac air flow duct)

Compressor Wiring Diagram for Chevrolet Corvette 2008

List of elements for Compressor Wiring Diagram for Chevrolet Corvette 2008:

• A/c comp fuse 15 10a
• A/c comp relay 35
• A/c compressor clutch (right front of engine block)
• E1 x2
• Engine control module (ecm) (behind right front fender, between wheelhouse & dash panel)
• F13
• F14
• G102 (on top of right frame rail, ground for sp102)
• H13
• H14
• Hot at all times
• J102
• Powertrain ign 1 relay 44
• Rly ctrl
• Underhood fuse block (on right side of engine compt)
• X1 c10

ANTI-LOCK BRAKES

Anti-lock Brakes Wiring Diagram (1 of 2) for Chevrolet Corvette 2008

List of elements for Anti-lock Brakes Wiring Diagram (1 of 2) for Chevrolet Corvette 2008:

• A10
• A11
• A12
• A13
• A14
• A4 x3
• Abs fuse 27 60a
• Abs/mrrtd fuse 3 10a
• B10
• B11
• B12
• B13
• B14
• Battery
• Brake pressure mod vlv
• Brake pressure modulator valve (bpmv) (left side of engine compt, mounted on frame rail)
• C10
• C11
• C12
• C13
• C14
• Computer data lines system
• E11
• Electronic brake control module (ebcm) (at left front side of engine compt, on frame rail)
• Electronic suspension system
• Engine control module (ecm) (behind right front fender, between wheelhouse & dash panel)
• G105 (on front left side of engine, above generator)
• Ground
• Hi spd gmlan ser data +
• Hi spd gmlan ser data -
• Hot at all times
• Hot in run or start
• Ign 1
• J195
• Lateral accelerometer sig
• Lf wheel speed sens low ref
• Lf wheel speed sens sig
• Lr wheel speed sens low ref
• Lr wheel speed sens sig
• Motor control
• Pnk
• Red
• Rf wheel speed sens low ref
• Rf wheel speed sens sig
• Rr wheel speed sens low ref
• Rr wheel speed sens sig
• Steering wheel position sig a
• Steering wheel position sig b
• Stop lmp sw sig
• Str whl pos sen 5-volt ref
• Str whl pos sen low ref
• Tan
• Transmissions system
• Underhood fuse block (on right side of engine compt)
• Var efrt str actu ctrl
• Var efrt str actu sply
• Variable effort steering actuator (on left side of steering rack assembly)
• W/ active brake control
• X4 b1
• Yaw rate sensor signal

Anti-lock Brakes Wiring Diagram (2 of 2) for Chevrolet Corvette 2008

List of elements for Anti-lock Brakes Wiring Diagram (2 of 2) for Chevrolet Corvette 2008:

• 5 volt reference
• 5v ref
• 5v reference
• Abs ind
• Body control module (bcm) (mounted on toe board, in right footwell)
• Brake fluid pressure sensor (w/ active brake control) (on left side of brake pressure modulator valve)
• Brake pedal position sensor (mounted on brake pedal bracket)
• Class 2 ser data
• Computer data lines system
• Ctrl switch signal
• Driver information center (dic)
• Ebcm gmlan
• G202 (at base of right "a" pillar)
• Hi spd gmlan ser data +
• Hi spd gmlan ser data -
• Ign
• Instrument panel cluster (ipc)
• Interior lights system
• J246
• Lateral accelerometer sig
• Left front wheel speed sensor (wss) (left front wheel)
• Left rear wheel
• Logic
• Low ref
• Low reference
• Position sw signal
• Right front wheel speed sensor (wss) (right front wheel)
• Right rear wheel speed sensor (wss) (right rear wheel)
• Speed sensor (wss) (left rear wheel)
• Steer wheel pos sig a
• Steer wheel pos sig b
• Steering angle sensor (w/ active brake control) (base of steering column, under dash)
• Stop lamp switch sig
• Tan
• Traction control off ind
• Traction control switch
• Underhood fuse block (on right side of engine compt)
• Yaw & lateral accelerometer sensor (w/ active brake control) (under hvac control head)
• Yaw rate sens signal

ANTI-THEFT

Forced Entry Wiring Diagram (1 of 2) for Chevrolet Corvette 2008

List of elements for Forced Entry Wiring Diagram (1 of 2) for Chevrolet Corvette 2008:

• (in i/p harness, left of audio amplifier) jx208
• (in i/p harness, left of steering column) jx205
• A/t shft lk ctrl
• Ajar
• Backup keyless entry antenna (right side of dash)
• Battery
• Closed
• D11
• Data link connector (dlc) (under dash, below steering column)
• Door ajar sw
• Door latch
• Door open sw
• Dr lk act ctrl
• Driver door latch (in rear of driver door)
• Dvr dr lk act
• Ecm/tcm/ easy key fuse 11 15a
• Exterior lights system
• Front passenger door latch (in rear of passenger door)
• G104 (on right frame rail, below battery tray)
• G301 (at left "b" pillar, behind trim panel)
• G302 (at right "b" pillar, behind trim panel)
• Ground
• Hot at all times
• Ign 1 volt
• Ign mod data
• Ignition mode switch
• J232
• J301
• J302
• K/e ant b-u sig
• K/e b-u low ref
• K/e left low ref
• K/e left sig
• K/e rear compt sig
• K/e right sig
• K/e rt low ref
• Left frnt int dr
• Left keyless entry antenna (top of left "b" pillar)
• Lf frt ext dr
• Open
• Pnk
• Rear compartment keyless entry antenna (below rear compt pull down actuator)
• Rear compt lo ref
• Remote control door lock receiver (rcdlr) (right side of dash)
• Rfa class 2 data
• Right keyless entry antenna (top of right "b" pillar)
• Rt frnt int dr
• Rt frt ext dr
• Shift interlock system
• Tan
• Trunk rel sw sig
• Trunk, tailgate, fuel doors system
• Underhood fuse block (on right side of engine compt)
• X2 a

Forced Entry Wiring Diagram (2 of 2) for Chevrolet Corvette 2008

List of elements for Forced Entry Wiring Diagram (2 of 2) for Chevrolet Corvette 2008:

• Battery
• Body control module (bcm) (mounted on toe board, in right footwell)
• Class 2 (bcm)
• Class 2 data
• Convertible
• Coupe
• Door latch ctrl
• Dr ajar sw sig
• Dr lck fuse 15a
• Dr lock ind
• Dr open sw sig
• Driv dr switch fuse 10a
• Driver door control module (ddm) (bottom center of driver door)
• Driver door lock indicator (in upper rear of driver door trim panel)
• Driver door lock switch
• Driver door unlatch pcb relay
• Driver exterior door handle switch (in upper rear of driver door)
• Driver interior door handle switch (in center of driver door panel)
• Driver window switch
• Front passenger door lock switch
• G201 (at base of left "a" pillar)
• G202 (at base of right "a" pillar)
• Ground
• Handle sw sig
• Headlights system
• Horn rel cntrl
• Horns system
• Hot at all times
• Ign
• Ign 1 volt
• Ign switch/ intr snsr fuse 10a
• Instrument panel cluster (ipc)
• Interior lights system
• Ipc class 2 serial data
• J539
• J579
• J640
• J680
• Lcd lamp
• Lock
• Lock cntrl
• Lock sig
• Logic
• Memory 1
• Memory 2
• Memory systems
• Nca
• Passenger door control module (fpdm) (bottom center of passenger door)
• Passenger door lock indicator (in upper rear of passenger door trim panel)
• Passenger door unlatch pcb relay
• Passenger exterior door handle switch (in upper rear of passenger door)
• Passenger interior door handle switch (in center of passenger door panel)
• Pk lamp rel
• Pnk
• Rear compartment lid latch assembly
• Rear compartment lid pulldown actuator
• Security ind
• Serial data
• Tan
• Trk ajar sw sig
• Un- lock
• Unlock cntrl
• Unlock sig

Steering Lock Wiring Diagram for Chevrolet Corvette 2008

List of elements for Steering Lock Wiring Diagram for Chevrolet Corvette 2008:

• (or 1932)
• (right side of dash) remote control door lock receiver (rcdlr)
• A lock ctrl
• A/t
• Automatic transmission shift lever (closed in park)
• B ground
• Backup lamp switch 1 (right side of manual transmission)
• Backup lamp switch 2 (right side of manual transmission)
• Batt
• Batt positive
• Body control module (bcm) (mounted on toe board, in right footwell)
• Btsi sol/str whl lck fuse 10a
• C unlock
• Clstr/ hud fuse 15a
• Computer data lines system
• D lock
• D10
• G201 (at base of left "a" pillar)
• Ground
• Hot at all times
• Hot w/ run crank relay energized
• Ign 1 voltage
• Instrument panel cluster (ipc)
• Ipc class 2
• Isrvm/hvac fuse 10a
• J100
• J218
• J231
• J251 (i/p harness, 6.5 cm from x150 breakout)
• J303
• Lock
• Lock ctrl
• Locked
• Logic
• M/t
• Message request
• Pnk
• Power distribution system
• Serial data
• Shift select sw sig (a/t) reverse lamp relay ctrl (m/t)
• Steering column lock control module (right side of steering column)
• Steering column lock ctrl
• Steering wheel theft deterrent lock
• Switch sig
• Unlock
• Unlocked

BODY CONTROL MODULES

Body Control Modules Wiring Diagram (1 of 4) for Chevrolet Corvette 2008

List of elements for Body Control Modules Wiring Diagram (1 of 4) for Chevrolet Corvette 2008:

• (not used)
• Accessory voltage
• Accy voltage sig
• Anti-theft system
• Bcm class 2 serial data
• Body control module (bcm) (mounted on toe board, in right footwell)
• Computer data lines system
• Conv top rly cvr rel ctrl
• Door locks system
• Electronic suspension system
• Exterior lights system
• Fog lamp rly ctrl
• Folding top cover pull down ajar sig
• Folding top cover rel sw
• G104 (on right frame rail, below battery tray)
• Headlamp hi beam rly ctrl
• Headlamp washer rly ctrl
• Headlights system
• Hood ajar switch signal
• Horn rly ctrl
• Horns system
• Ign mode sw pwr
• Ignition mode sw ctrl
• Ignition mode sw start led sig
• Intrusion sensor alarm on sig
• Intrusion sns alarm on sig
• J232
• Lf door ajar sw sig
• Lf door open sw sig
• Lf turn sig lamp pwr
• Logic
• Park lamp relay ctrl
• Pnk
• Power distribution system
• Power sounder enable signal
• Power tops system
• Rf door ajar sw sig
• Rf door open sw sig
• Rf turn sig lamp pwr
• Selective ride ctrl sw sig
• Shift interlock system
• Signal ground
• Steering column lock control
• Tan
• Trunk ajar sw sig
• Trunk key sw sig
• Trunk release rly ctrl
• Trunk, tailgate, fuel doors system
• W/w mtr park sw sig
• Windshield wiper sw sig 2
• Wiper/washer system

Body Control Modules Wiring Diagram (2 of 4) for Chevrolet Corvette 2008

List of elements for Body Control Modules Wiring Diagram (2 of 4) for Chevrolet Corvette 2008:

• A10
• A11
• A12
• B10
• B11
• B12
• B3 b3
• Backup lamp pwr
• Batt 3 fuse 26 60a
• Batt 5 fuse 7 30a
• Battery
• Battery voltage +
• Body control module (bcm) (mounted on toe board, in right footwell)
• C10
• C11
• C12
• Computer data lines system
• Courtesy lamp ctrl
• D10
• D11
• D12
• Door lock actuator unlock ctrl
• Door locks system
• Drvr dr lock actuator unlock ctrl
• Exterior lights system
• Hot at all times
• Ign 1 voltage
• Ign mode sw led pwr
• Inside logic
• Interior lights system
• J208
• Logic
• Pnk
• Power distribution system
• Power tops system
• Seats system
• Sound systems
• Stop/b/u/ lamps fuse 5 15a
• Tan
• Underhood fuse block (on right side of engine compt)
• Windshield washer sw sig
• Wiper/washer system

Body Control Modules Wiring Diagram (3 of 4) for Chevrolet Corvette 2008

List of elements for Body Control Modules Wiring Diagram (3 of 4) for Chevrolet Corvette 2008:

• (not used)
• A10
• A11
• A12
• Accessory voltage
• Air conditioning system
• B10
• B11
• B12
• Batt
• Battery
• Body control module (bcm) (mounted on toe board, in right footwell)
• C10
• C11
• C12
• Courtesy lamp sw sig
• D10
• D11
• D12
• E10
• E11
• E12
• Exterior lights system
• F10
• F11
• F12
• G202 (at base of right "a" pillar)
• Ground
• Headlights system
• Ign 1 voltage
• Inside logic
• Instrument cluster system
• Interior lights system
• J216
• Logic
• Mirrors system
• Pnk
• Power distribution system
• Power tops system
• Power windows system
• Reverse lamp
• Sound systems
• Stop lamp sw sig
• Stop lamp voltage
• Windshield washer sw sig
• Wiper/washer system

Body Control Modules Wiring Diagram (4 of 4) for Chevrolet Corvette 2008

List of elements for Body Control Modules Wiring Diagram (4 of 4) for Chevrolet Corvette 2008:

• (not used)
• Anti-lock brakes system
• Anti-theft system
• Body control module (bcm) (mounted on toe board, in right footwell)
• Brake pedal pos sen sig
• Brake pos sens 5v ref
• Brake pos sens low ref
• Computer data lines system
• Crs ctrl set/cst/res/accl sw sig
• Cruise control system
• Exterior lights system
• Flash to pass sig
• Fog lamp rly ctrl
• Front fog lamp sw sig
• Hard top connected sig
• Hazard switch sig
• Headlamp dimmer sw hi beam sig
• Headlamp low beam rly ctrl
• Headlamps sw on sig
• Headlights system
• High speed gmlan ser bus +
• High speed gmlan ser bus -
• Horn rly ctrl
• Horns system
• Ign mode sw accy led sig
• Ign mode sw off led sig
• Intrusion sns sw disable sig
• Lf turn sig sw sig
• Logic
• Park lamp sw off sig (2)
• Park lamp sw sig
• Pnk
• Power distribution system
• Power tops system
• Rear fog lamp relay switch
• Rear fog lamp switch signal
• Rf turn sig sw sig
• Shift interlock system
• Shift sel sw park sig
• Signal ground
• Tan
• Traction ctrl sw sig
• Windshield wiper sw low sig
• Wiper/washer system

COMPUTER DATA LINES

Computer Data Lines Wiring Diagram, A/T for Chevrolet Corvette 2008

List of elements for Computer Data Lines Wiring Diagram, A/T for Chevrolet Corvette 2008:

• (not used)
• Automatic transmission
• B10
• B11
• B12
• B15
• Body control module (bcm) (mounted on toe board in right footwell)
• Center of drivers seat)
• Class 2 serial data
• Class serial data
• D14
• Data link connector (dlc) (under dash, below steering column)
• Digital radio receiver (if equipped) (coupe: behind left rear driver seat, in left rear compt) (convertible: between driver & passenger seat, mounted on bracket, below tonneau)
• Driver door module (ddm) (bottom center of driver door)
• Driver memory seat module (under
• Driver window switch
• Electronic brake control module (ebcm) (at left front side of engine compt, on frame rail)
• Electronic suspension control (esc) module (w/ magnetic ride control) (behind the right front fender, above ecm)
• Engine control module (ecm) (behind right front fender, between wheelhouse & dash panel)
• Exhaust tail pipe flow valve control module (7.0l) (right side of rear compt, behind wheelwell)
• Folding top control module (if equipped) (between driver & passenger seat, mounted on bracket below tonneau latch actuator)
• Front passenger door module (fpdm) (bottom center of passenger door)
• G104 (on right frame rail, below battery tray)
• G201 (at base of left "a" pillar)
• Gmlan data bus +
• Gmlan data bus -
• Head up display (hud) (if equipped) (top left side of dash)
• High speed gmlan serial data bus +
• High speed gmlan serial data bus -
• Hot at all times
• Hvac control module (center of dash, under radio)
• Inflatable restraint sensing & diagnostic module (sdm) (behind center of dash, under hvac control head)
• Instrument panel cluster (ipc)
• J200
• J232
• Jx205 (in i/p harness, left of steering column)
• Jx208 (in i/p harness, left of audio amplifier)
• Logic
• Pnk
• Radio
• Rear fog/ aldl top swtch fuse 10a
• Remote control door lock receiver (rcdlr) (right side of dash)
• Tan
• Transmission control module (tcm)
• Vehicle communication interface module (vcim) (w/ onstar) (in right rear compt)
• W/ onstar
• W/o onstar

Computer Data Lines Wiring Diagram, M/T for Chevrolet Corvette 2008

List of elements for Computer Data Lines Wiring Diagram, M/T for Chevrolet Corvette 2008:

• (not used)
• B10
• B11
• B12
• B14
• B15
• Body control module (bcm) (mounted on toe board in right footwell)
• Center of drivers seat)
• Class 2
• Class 2 serial data
• Class serial data
• Data link connector (dlc) (under dash, below steering column)
• Digital radio receiver (if equipped) (coupe: behind left rear driver seat, in left rear compt) (convertible: between driver & passenger seat, mounted on bracket, below tonneau)
• Driver door module (ddm) (bottom center of driver door)
• Driver memory seat module (under
• Driver window switch
• Electronic brake control module (ebcm) (at left front side of engine compt, on frame rail)
• Electronic suspension control (esc) module (behind the right front fender, above ecm)
• Engine control module (ecm) (behind right front fender, between wheelhouse & dash panel)
• Exhaust tail pipe flow valve control module (7.0l) (right side of rear compt, behind wheelwell)
• Folding top control module (if equipped) (between driver & passenger seat, mounted on bracket below tonneau latch actuator)
• Front passenger door module (fpdm) (bottom center of passenger door)
• G104 (on right frame rail, below battery tray)
• G201 (at base of left "a" pillar)
• Gmlan data bus +
• Gmlan data bus -
• Head up display (hud) (if equipped) (top left side of dash)
• High speed gmlan serial data bus +
• High speed gmlan serial data bus -
• Hot at all times
• Hvac control module (center of dash, under radio)
• Inflatable restraint sensing & diagnostic module (sdm) (behind center of dash, under hvac control head)
• Instrument panel cluster (ipc)
• J200
• J232
• Jx205 (in i/p harness, left of steering column)
• Jx208 (in i/p harness, left of audio amplifier)
• Logic
• Pnk
• Radio
• Rear fog/ aldl top swtch fuse 10a
• Remote control door lock receiver (rcdlr) (right side of dash)
• Serial data x1
• Steering column lock control module (right side of steering column)
• Tan
• Vehicle communication interface module (vcim) (w/ onstar) (in right rear compt)
• W/ magnetic ride control
• W/ onstar
• W/o magnetic ride control
• W/o onstar

COOLING FAN

Cooling Fan Wiring Diagram for Chevrolet Corvette 2008

List of elements for Cooling Fan Wiring Diagram for Chevrolet Corvette 2008:

• (behind right front fender, between wheelhouse & dash panel)
• (front of engine compt, rear of radiator) fan control module
• (top left side of dash) head up display (hud)
• Bat
• Check gages
• Computer data lines system
• Coolant over temp engine hot/stop engine low coolant
• Coolfan fuse 25 60a
• Engine control module (ecm)
• Engine coolant temperature (ect) sensor (in front left side of left cylinder head)
• Engine cooling fan (rear of radiator)
• G102 (on top of right frame rail, ground for sp102)
• Gnd
• Hot at all times
• Hud class 2 serial data
• Hud message center
• Hvac control module (center of dash, under radio)
• Ign
• Instrument panel cluster (ipc)
• Ipc class 2 serial data
• Logic
• Low ref
• Message center
• Message request
• Red
• Sens sig
• Serial data
• Serial data +
• Serial data -
• Spd ctrl
• Speed ctrl
• Tan
• Underhood fuse block (on right side of engine compt)

CRUISE CONTROL

Cruise Control Wiring Diagram, A/T for Chevrolet Corvette 2008

List of elements for Cruise Control Wiring Diagram, A/T for Chevrolet Corvette 2008:

• 5 volt reference
• 5-volt reference 1
• 5-volt reference 2
• 5v ref
• Accelerator pedal position sensor (app) (on top of accelerator pedal, part of mounting bracket)
• App sensor 1 signal
• App sensor 2 signal
• Body control module (bcm) (mounted on toe board, in right footwell)
• Brake pedal pos sw sig
• Brake pedal position sensor (mounted on brake pedal bracket)
• C4 x4
• Computer
• Computer data lines system
• Control (tac) motor
• Cruise control switch
• Cruise ctrl set/coast & resume/ acc sw signal
• Cruise switch fuse 2a
• Data lines
• Distribution
• Driver information center
• E8 x4
• Engine control module (ecm) (behind right front fender, between wheelhouse & dash panel)
• Head up display (hud) (if equipped)
• High speed gmlan serial data bus +
• High speed gmlan serial data bus -
• Hot w/ run/crank relay energized
• Hud class 2 serial data
• Instrument panel cluster (ipc)
• Ipc class 2 serial data
• J211 (right ignition control module jumper, 4.0 cm from breakout to ignition coil/module 4)
• Logic
• Low ref
• Low reference
• Message request
• Nca
• Off
• Pnk
• Power
• Radio
• Res+
• Serial data bus +
• Serial data bus -
• Set-
• Stop lamp sw sig
• System
• Tac motor ctrl 1
• Tac motor ctrl 2
• Tan
• Throttle actuator m
• Throttle body assembly (upper front center of engine, forward of intake manifold)
• Throttle position (tp) sensor
• Tp sensor 1 signal
• Tp sensor 2 signal
• Transmission control module (tcm) (in engine compt)
• Turn signal/multi-function switch
• Underhood fuse block (on right side of engine compt)
• Vehicle speed sig
• X400

Cruise Control Wiring Diagram, M/T for Chevrolet Corvette 2008

List of elements for Cruise Control Wiring Diagram, M/T for Chevrolet Corvette 2008:

• (tac) motor
• (tp) sensor
• 5 volt reference
• 5-volt reference 1
• 5-volt reference 2
• 5v ref
• Accelerator pedal position sensor (app) (on top of accelerator pedal, part of mounting bracket)
• App sensor 1 signal
• App sensor 2 signal
• Body control module (bcm) (mounted on toe board, in right footwell)
• Brake pedal pos sw sig
• Brake pedal position sensor (mounted on brake pedal bracket)
• C4 x4
• Clutch pedal position (cpp) sensor
• Clutch pedal sen sig
• Clutch sen ctrl
• Computer
• Computer data lines system
• Control
• Cruise control switch
• Cruise ctrl set/coast & resume/ acc sw signal
• Cruise switch fuse 2a
• Data lines
• Driver information center
• Engine control module (ecm) (behind right front fender, between wheelhouse & dash panel)
• Head up display (hud) (if equipped)
• High speed gmlan serial data bus +
• High speed gmlan serial data bus -
• Hot w/ run/crank relay energized
• Hud class 2 serial data
• Instrument panel cluster (ipc)
• Ipc class 2 serial data
• J211 (right ignition control module jumper, 4.0 cm from breakout to ignition coil/module 4)
• Logic
• Low ref
• Low reference
• Message request
• Nca
• Off
• Pnk
• Radio
• Res+
• Serial data bus +
• Serial data bus -
• Set-
• Stop lamp sw sig
• System
• Tac motor ctrl 1
• Tac motor ctrl 2
• Tan
• Throttle actuator
• Throttle body (upper front center of engine)
• Throttle position
• Tp sensor 1 signal
• Tp sensor 2 signal
• Turn signal/multi-function switch
• Underhood fuse block (on right side of engine compt)
• Vehicle speed sensor (vss) (on top right side of differential)
• Vehicle speed sig
• Vss high sig
• Vss low sig

DEFOGGERS

Defoggers Wiring Diagram for Chevrolet Corvette 2008

List of elements for Defoggers Wiring Diagram for Chevrolet Corvette 2008:

• A18
• A19
• Batt 2 fuse 29 30a
• C18
• C19
• Class 2 ser data
• Computer data lines system
• D10 x3
• Defog ctrl
• Defog rly ctrl
• Defogger switch
• Driver door control module (bottom center of driver door)
• Driver outside rearview mirror
• Driver outside rearview mirror glass
• E10
• G201 (at base of left "a" pillar)
• G202 (at base of right "a" pillar)
• G301 (at left "b" pillar, behind trim panel)
• Hot at all times
• Htd mirror elmnt sply
• Hvac control module (center of dash, under radio)
• Ign
• J301
• J539
• J640
• Logic
• Nca
• Passenger control door module (bottom center of passenger door)
• Passenger outside rearview mirror
• Rear defog relay 40
• Rear window defogger grid
• Tan
• Under- hood fuse block (on right side of engine compt)

ELECTRONIC MUFFLER

Electronic Muffler Wiring Diagram for Chevrolet Corvette 2008

List of elements for Electronic Muffler Wiring Diagram for Chevrolet Corvette 2008:

• (bottom left of vehicle, on right rear impact bar assembly)
• Battery
• Body control module (bcm) (mounted on toe board, in right footwell)
• Computer data lines system
• Exh mdl fuse 10a
• Exhaust tail pipe flow control valve solenoid
• Exhaust tail pipe flow valve control module (right side of rear compt, behind wheelwell)
• G302 (at right "b" pillar, behind trim panel)
• Ground
• Hot at all times
• J302
• Serial data
• Tan
• X3 d4

ELECTRONIC POWER STEERING

Electronic Power Steering Wiring Diagram for Chevrolet Corvette 2008

List of elements for Electronic Power Steering Wiring Diagram for Chevrolet Corvette 2008:

• (on left side of steering rack assembly) variable effort steering actuator
• 5-volt ref
• 5v ref
• 5v reference
• Abs fuse 27 60a
• Abs/mrrtd fuse 3 10a
• B10
• B11
• B12
• B13
• B14
• Battery
• Brake fluid pressure sens sig
• Brake fluid pressure sensor (on left side of brake pressure modulator valve)
• C10
• Computer data lines system
• E11
• Electronic brake control module (ebcm) (at left front side of engine compt, on frame rail)
• G105 (on front left side of engine, above generator)
• Ground
• Hi spd gmlan ser data +
• Hi spd gmlan ser data -
• Hot at all times
• Hot w/ run crank relay energized
• Ign 1 volt
• J195
• Lateral accelerometer sig
• Low ref
• Low reference
• Pnk
• Power distribution system
• Red
• Steer wheel pos sig a
• Steer wheel pos sig b
• Steering angle sensor (base of steering column, under dash)
• Steering wheel position sig a
• Steering wheel position sig b
• Tan
• Underhood fuse block (on right side of engine compt)
• Var efrt str actuator sply ctrl
• Var efrt str actuator sply volt
• X4 b1
• Yaw & lateral acceleration sensor (under hvac control head)
• Yaw rate sens signal
• Yaw rate sensor sig

ELECTRONIC SUSPENSION

Electronic Suspension Wiring Diagram for Chevrolet Corvette 2008

List of elements for Electronic Suspension Wiring Diagram for Chevrolet Corvette 2008:

• (at rear of vehicle, on inner side of right frame rail) g402
• Abs/ mrrtd fuse 3 10a
• Batt
• Battery voltage
• Body control module (bcm) (mounted on toe board, in right footwell)
• Clstr/ hud fuse 15a
• Computer data lines system
• D10
• E11
• Electronic suspension control (esc) module (behind the right front fender, above ecm)
• G202 (at base of right "a" pillar)
• Gmlan ser data
• Ground
• Hot at all times
• Hot w/ run crank relay energized
• Ignition 1 voltage
• Instrument panel cluster (ipc)
• Interior lights system
• Ipc class 2
• J246
• J420
• Left front suspension damper solenoid (left front shock absorber)
• Left front suspension position sensor (w/ magnetic ride control) (left front suspension shock absorber)
• Left rear suspension damper solenoid (left rear shock absorber)
• Left rear suspension position sensor (w/ magnetic ride control) (left rear suspension control arm)
• Lf damper ctrl
• Lf damper low ref
• Lf position sens
• Logic
• Lr damper ctrl
• Lr damper low ref
• Lr position sens
• Message center
• Message request
• Mrrtd fuse 13 25a
• Nca
• Pnk
• Power distribution system
• Rf damper ctrl
• Rf damper low ref
• Rf position sens
• Ride control switch signal x1
• Right front suspension damper solenoid (right front shock absorber)
• Right front suspension position sensor (w/ magnetic ride control) (right front suspension shock absorber)
• Right rear suspension damper solenoid (right rear shock absorber)
• Right rear suspension position sensor (w/ magnetic ride control) (right rear suspension control arm)
• Rr damper ctrl
• Rr damper low ref
• Rr position sens
• Sensor low ref
• Service ride control
• Suspension control switch
• Tan
• Underhood fuse block (on right side of engine compt)
• Voltage reference

ENGINE PERFORMANCE

6.2L VIN W

6.2L VIN W, Engine Performance Wiring Diagram (1 of 4) for Chevrolet Corvette 2008

List of elements for 6.2L VIN W, Engine Performance Wiring Diagram (1 of 4) for Chevrolet Corvette 2008:

• (m/t) reverse lockout solenoid
• 5v reference 1
• 5v reference 2
• B9 x2
• C10
• Ckp sensor
• Cmp sensor
• Duty cycle sig
• Ect sensor sig
• Engine control module (ecm) (behind right front fender, between wheelhouse & dash panel)
• Evap canister purge
• Even inj fuse 16 20a
• From inj a fuses (diagram 2 of 4)
• Fuel injector 1
• Fuel injector 2
• Fuel injector 3
• Fuel injector 4
• Fuel injector 5
• Fuel injector 6
• Fuel injector 7
• Fuel injector 8
• Fuel injectors (1, 3, 5 & 7: top left side of engine, below fuel rail) (2, 4, 6 & 8: top right side of engine, below fuel rail)
• Hi sig
• Ic 1 ctrl
• Ic 2 ctrl
• Ic 3 ctrl
• Ic 4 ctrl
• Ic 5 ctrl
• Ic 6 ctrl
• Ic 7 ctrl
• Ic 8 ctrl
• Ks low ref
• Ks sig
• Ks signal
• Low ctrl
• Low ref
• Low reference
• Low sig
• Map sensor signal
• Odd inj fuse 12 20a
• Oil level sw sig
• Oil pressure sens sig
• Park/neu sig
• Pnk
• Red
• Reverse lockout
• Starting/ charging system
• Tac motor ctrl 1
• Tac motor ctrl 2
• Tan
• Tft sns sig
• Throttle body assembly (upper front center of engine, forward of intake manifold)
• Tp sns 1 sig
• Tp sns 2 sig
• Transmission fluid temperature (tft) sensor (m/t) (inside transmission)
• Turn on sig
• Underhood fuse block (on right side of engine compt)
• W/ cooling system

6.2L VIN W, Engine Performance Wiring Diagram (2 of 4) for Chevrolet Corvette 2008

List of elements for 6.2L VIN W, Engine Performance Wiring Diagram (2 of 4) for Chevrolet Corvette 2008:

• (12.5 cm from connector x140 breakout) j146
• (6.0 cm from connector x140 breakout)
• (a/t) automatic transmission
• (on left exhaust pipe, forward of catalytic converter) heated oxygen sensor (ho2s) bank 1 sensor 1
• (on right exhaust pipe, forward of catalytic converter) heated oxygen sensor (ho2s) bank 2 sensor 1
• (on valve cover, top of 1, 3, 5 & 7 cylinders)
• (on valve cover, top of 2, 4, 6 & 8 cylinders)
• A/c comp relay
• C10 x1
• D10
• E10
• Emission fuse 14 15a
• F13
• F14
• Fuel pump fuse 20 20a
• Fuel pump relay
• G102 (on top of right frame rail, ground for sp102)
• G107 (left side of engine, middle of block)
• H13
• H14
• Hot at all times
• Ignition coil 1
• Ignition coil 2
• Ignition coil 3
• Ignition coil 4
• Ignition coil 5
• Ignition coil 6
• Ignition coil 7
• Ignition coil 8
• J102
• J131
• J133
• J135 (12.5 cm from connector x140 breakout)
• J142
• J144
• J420
• Man tran sol fuse 10 10a
• Mrrtd fuse 13 25a
• Nca
• O2 sen fuse 6 15a
• Park/ neutral sig
• Pnk
• Pnk d
• Power- train ign 1 relay
• Pt input/ etc fuse 9 10a
• Red
• Red c
• Spark plug
• Tan
• To inj fuses (diagram 1 of 4)
• Transmission control module (tcm)
• Underhood fuse block (on right side of engine compt)
• X2 a6
• X2 b6

6.2L VIN W, Engine Performance Wiring Diagram (3 of 4) for Chevrolet Corvette 2008

List of elements for 6.2L VIN W, Engine Performance Wiring Diagram (3 of 4) for Chevrolet Corvette 2008:

• (back of throttle body, right front of engine) evaporative emission (evap) canister purge solenoid valve
• (on air intake assembly) intake air temperature (iat)/ mass air flow (maf) sensor
• (on left exhaust pipe, rearward of catalytic converter) heated oxygen sensor (ho2s) bank 1 sensor 2
• (on right exhaust pipe, rearward of catalytic converter)
• (on right rear side of engine, above starter solenoid)
• (right rear side of underbody) evaporative emission (evap) canister vent solenoid valve
• (under vehicle, on left side of transmission) (m/t) skip shift solenoid
• Accelerator pedal position (app) sensor (on top of accelerator pedal, part of mounting bracket)
• Accy volt sig
• B10
• Body control module (mounted on toe board, in right footwell)
• Camshaft position (cmp) sensor (lower left front of engine)
• Crankshaft position (ckp) sensor (on lower right side of engine, behind starter)
• Ecm fuse 15a
• Engine coolant temperature (ect) sensor (in front left side of left cylinder head)
• Engine oil level/ temperature sensor (on bottom right center of engine oil pan)
• Engine oil pressure (eop) sensor (on top center rear of engine)
• G106
• Gnd
• Heated oxygen sensor (ho2s) bank 2 sensor 2
• Hot w/ run crank relay energized
• Ign 1
• Knock sensor bank 1 (on center left side of engine)
• Knock sensor bank 2 (on lower center right side of engine)
• Logic
• Maf
• Manifold absolute pressure (map) sensor (front center of engine, behind throttle body)
• Nca
• Pnk
• Starting/ charging system
• Stop lamp sig
• Tan
• W/ first to fourth gear skip shift

6.2L VIN W, Engine Performance Wiring Diagram (4 of 4) for Chevrolet Corvette 2008

List of elements for 6.2L VIN W, Engine Performance Wiring Diagram (4 of 4) for Chevrolet Corvette 2008:

• (20 cm from connector x420 breakout)
• (20 cm from connector x460 breakout)
• (right ignition control module jumper, 4.0 cm from breakout to ignition coil/ module 4)
• (top left side of dash) (if equipped) head up display (hud)
• 1 to 4 shift ind
• 5v ref 2
• 5v reference 1
• A/c com clutch rly
• A/c refrigerant
• A/c refrigerant pressure sensor (on a/c high pressure line)
• Accessory voltage
• Air conditioning system
• App sensor 1 sig
• App sensor 2 sig
• Battery pos volt
• Computer data lines system
• Cooling fan rly
• Cooling fans system
• Cruise control system
• D11
• Data
• Driver information center (dic)
• Ecm/tcm/ easy key fuse 11 15a
• Engine control module (ecm) (behind right front fender, between wheelhouse & dash panel)
• Engine speed sig
• Ess
• Evap canister vent
• Fuel level sens sig
• Fuel pump & sender assembly (in left fuel pump assembly)
• Fuel pump relay
• Fuel tank pressure
• Fuel tank pressure (ftp) sensor (in right fuel tank)
• G106 (on right rear side of engine, above starter solenoid)
• G401 (at rear of vehicle, on inner side of left frame rail)
• Gnd
• Ground
• Hi sig
• Hot at all times
• Iat sens sig
• Ignition 1 relay ctrl
• Ignition 1 voltage
• Instrument panel cluster (ipc)
• J106
• J211
• J400
• J460
• J462
• Logic
• Low ctrl
• Low ref
• Low reference
• Low sig
• Low signal
• Maf sensor sig
• Mil control
• Mil ind
• Navigation & sound systems
• Pnk
• Pos sen sig
• Radio
• Secondary (right) fuel level sensor (in right fuel tank)
• Serial data bus +
• Serial data bus -
• Skip/shift
• Sns sig
• Start rly ctrl
• Starting/charging system
• Stop lamp sw sig
• Tan
• Transmissions system
• Underhood fuse block (on right side of engine compt)
• Vehicle speed sensor (vss) (m/t) (on top right side of differential)
• Vehicle speed sig
• Vss
• Vss high sig
• Vss low sig

7.0L VIN E

7.0L VIN E, Engine Performance Wiring Diagram (1 of 4) for Chevrolet Corvette 2008

List of elements for 7.0L VIN E, Engine Performance Wiring Diagram (1 of 4) for Chevrolet Corvette 2008:

• (m/t) reverse lockout solenoid
• 5v reference
• 5v reference 1
• 5v1
• 5v2
• B9 x2
• C10
• Ckp sensor
• Cmp sensor
• Duty cycle sig
• Ect sens sig
• Engine control module (ecm) (behind right front fender, between wheelhouse & dash panel)
• Evap canister purge
• Even inj fuse 16 20a
• From 02 a sens fuse (diagram 2 of 4)
• Fuel injector 1
• Fuel injector 2
• Fuel injector 3
• Fuel injector 4
• Fuel injector 5
• Fuel injector 6
• Fuel injector 7
• Fuel injector 8
• Fuel injectors (1, 3, 5 & 7: left side of engine) (2, 4, 6 & 8: right side of engine)
• Hi sig
• Ic 1 ctrl
• Ic 2 ctrl
• Ic 3 ctrl
• Ic 4 ctrl
• Ic 5 ctrl
• Ic 6 ctrl
• Ic 7 ctrl
• Ic 8 ctrl
• Ks low ref
• Ks sig
• Ks signal
• Low crtl
• Low ctrl
• Low ref
• Low reference
• Low sig
• Odd inj fuse 12 20a
• Oil pressure sens sig
• Park/neu sig
• Pnk
• Red
• Reverse lockout
• Starting/ charging system
• Tac motor ctrl 1
• Tac motor ctrl 2
• Tan
• Tft sns sig
• Throttle body (upper front center of engine)
• Tp sns 1 sig
• Tp sns 2 sig
• Transmission fluid temperature (tft) sensor (m/t) (inside transmission)
• Turn on sig
• Underhood fuse block (on right side of engine compt)
• W/ cooling system

7.0L VIN E, Engine Performance Wiring Diagram (2 of 4) for Chevrolet Corvette 2008

List of elements for 7.0L VIN E, Engine Performance Wiring Diagram (2 of 4) for Chevrolet Corvette 2008:

• (12.5 cm from connector x140 breakout) j146
• (6.0 cm from connector x140 breakout)
• (6.0 cm from connector x140 breakout) j131
• (a/t) automatic transmission
• (in left exhaust pipe before catalytic converter)
• (in right exhaust pipe, before
• (left side of engine)
• (right side of engine)
• A/c comp relay
• A6 x2
• C10 x1
• Catalytic converter)
• D10
• E10
• Emission fuse 14 15a
• F13
• F14
• Fuel pump fuse 20 20a
• Fuel pump relay
• G102 (on top of right frame rail, ground for sp102)
• G107 (left side of engine, middle of block)
• H13
• H14
• Heated oxygen sensor (ho2s) bank 1 sensor 1
• Heated oxygen sensor (ho2s) bank 2 sensor 1
• Hot at all times
• Ignition coil 1
• Ignition coil 2
• Ignition coil 3
• Ignition coil 4
• Ignition coil 5
• Ignition coil 6
• Ignition coil 7
• Ignition coil 8
• J102
• J133
• J135 (12.5 cm from connector x140 breakout)
• J142
• J144
• J420
• Man tran sol fuse 10 10a
• Mrrtd fuse 13 25a
• Nca
• O2 sen fuse 6 15a
• Park/ neutral sig
• Plug spark
• Pnk
• Power- train ign 1 relay
• Pt input/ etc fuse 9 10a
• Red
• Spark plug
• Tan
• To inj fuses (diagram 1 of 4)
• Transmission control module (tcm)
• Underhood fuse block (on right side of engine compt)
• X2 b6

7.0L VIN E, Engine Performance Wiring Diagram (3 of 4) for Chevrolet Corvette 2008

List of elements for 7.0L VIN E, Engine Performance Wiring Diagram (3 of 4) for Chevrolet Corvette 2008:

• (in exhaust pipe, rear of catalytic converter) heated oxygen sensor (ho2s) bank 1 sensor 2
• (in right exhaust pipe after catalytic converter) heated oxygen sensor (ho2s) bank 2 sensor 2
• (on air intake assembly) intake air temperature (iat)/ mass air flow (maf) sensor
• (right front of engine) evaporative emission (evap) canister
• (right rear side of underbody) evaporative emission (evap) canister
• (under vehicle, on left side of transmission) (m/t) skip shift solenoid
• Accelerator pedal position (app) sensor (on top of accelerator pedal, part of mounting bracket)
• Accy volt sig
• B10
• Body control module (mounted on toe board, in right footwell)
• Camshaft position (cmp) sensor (on front of engine)
• Crankshaft position (ckp) sensor (on right side of engine above starter)
• Ecm fuse 15a
• Engine coolant temperature (ect) sensor (in front left side of left cylinder head)
• Engine oil pressure (eop) sensor (on top rear of engine)
• Engine oil temperature (eot) sensor (on bottom of oil tank)
• G106 (on right rear side of engine, above starter solenoid)
• Gnd
• Hot w/ run crank relay energized
• Ign 1
• Knock sensor (ks) bank 1 (left side of engine)
• Knock sensor (ks) bank 2 (on right side of engine)
• Logic
• Maf
• Manifold absolute pressure (map) sensor (top front of engine)
• Nca
• Pnk
• Purge solenoid valve
• Red
• Stop lamp sig
• Tan
• Vent solenoid valve
• W/ first to fourth gear skip shift

7.0L VIN E, Engine Performance Wiring Diagram (4 of 4) for Chevrolet Corvette 2008

List of elements for 7.0L VIN E, Engine Performance Wiring Diagram (4 of 4) for Chevrolet Corvette 2008:

• (20 cm from connector x420 breakout)
• (20 cm from connector x460 breakout)
• (right ignition control module jumper, 4.0 cm from breakout to ignition coil/module 4)
• (top left side of dash) (if equipped) head up display (hud)
• 1 to 4 shift ind
• 5v1
• 5v2
• A/c com clutch rly
• A/c refrigerant
• A/c refrigerant pressure sensor (on a/c high pressure line)
• Accessory voltage
• Air conditioning system
• App sensor 1 sig
• App sensor 2 sig
• Battery pos volt
• Computer data lines system
• Cooling fan rly
• Cooling fans system
• Cruise control system
• D11
• Data
• Driver information center (dic)
• Ecm/tcm/ easy key fuse 11 15a
• Engine control module (ecm) (behind right front fender, between wheelhouse & dash panel)
• Engine speed sig
• Ess
• Evap canister vent
• Fuel level sens sig
• Fuel pump & sender assembly (in left fuel pump assembly)
• Fuel pump relay
• Fuel tank pressure
• Fuel tank pressure (ftp) sensor (in right fuel tank)
• G106 (on right rear side of engine, above starter solenoid)
• G401 (at rear of vehicle, on inner side of left frame rail)
• Gnd
• Ground
• Hi sig
• Ho2s low signal
• Hot at all times
• Iat sens sig
• Ignition 1 relay ctrl
• Ignition 1 voltage
• Instrument panel cluster (ipc)
• J106
• J211
• J400
• J460
• J462
• Logic
• Low ctrl
• Low ref
• Low reference
• Low sig
• Maf sensor sig
• Mil control
• Mil ind
• Pnk
• Pos sens ctrl
• Pos sens sig
• Radio
• Secondary (right) fuel level sensor (in right fuel tank)
• Serial data bus +
• Serial data bus -
• Skip/shift
• Sns sig
• Starter rly ctrl
• Starting/charging system
• Stop lamp sw sig
• Tan
• Underhood fuse block (on right side of engine compt)
• Vehicle speed sensor (m/t) (on top right side of differential)
• Vehicle speed sig
• Vss
• Vss high sig
• Vss low sig

EXTERIOR LIGHTS

Backup Lamps Wiring Diagram for Chevrolet Corvette 2008

List of elements for Backup Lamps Wiring Diagram for Chevrolet Corvette 2008:

• Automatic transmission (if equipped)
• Automatic transmission internal mode switch
• B11
• Backup lamp rly ctrl
• Backup lamp switch 2 (right side of manual transmission)
• Bck/up lamp relay
• Body control module (bcm) (mounted on toe board, in right footwell)
• Class 2 ser data
• Computer data lines system
• D10
• Door locks system
• Electronic power steering system
• G106 (on right rear side of engine, above starter solenoid)
• G302 (at right "b" pillar, behind trim panel)
• Gm lan ser data bus +
• Gm lan ser data bus -
• Ground
• Hi spd ser data +
• Hi spd ser data -
• Hot at all times
• J100
• J106
• J218
• J900
• J931
• Left backup lamp
• Logic
• M/t
• Red
• Reverse lamp relay control
• Reverse lamps fuse 10a
• Right backup lamp
• Stop/ b/u/lamps fuse 5 15a
• Tan
• Transmission control module (tcm)
• Trs a sig
• Trs b sig
• Underhood fuse block (on right side of engine compt)

Exterior Lamps Wiring Diagram (1 of 2) for Chevrolet Corvette 2008

List of elements for Exterior Lamps Wiring Diagram (1 of 2) for Chevrolet Corvette 2008:

• (behind right front fender, between wheelhouse & dash panel) engine control module (ecm)
• (if equipped) automatic transmission
• (in forward lamp harness, 26 cm from horn assembly breakout) j105
• 5v ref
• A12
• Auto
• B11
• Body control module (bcm) (mounted on toe board, in right footwell)
• Brake pedal position sensor (mounted on brake pedal bracket)
• Brk pos sens sig
• C11
• C12
• Center high mounted stop lamp (chmsl)
• Class 2 ser data
• Computer data lines system
• F10
• F11
• G101 (on left frame rail)
• G102 (on top of right frame rail, ground for sp102)
• G201 (at base of left "a" pillar)
• G302 (at right "b" pillar, behind trim panel)
• Hazard sw sig
• Head
• Hot at all times
• Instrument cluster system
• J101
• J102
• J119
• J120
• J275
• J931
• Left front marker lamp
• Left park/ turn signal lamp
• Lf trn sig vlt
• Logic
• Low ref
• Lt trn sig sw
• Off
• Park
• Park lamp relay 37
• Pk lamps fuse 8 10a
• Prk lmp rly cntl
• Prk lmp sw on sig
• Rf trn sig vlt
• Right front marker lamp
• Right park/ turn signal lamp
• Rt trn sig sw
• Stop/ b/u/ lamps fuse 5 15a
• Stp lmp sw sig
• Tan
• Transmission control module (tcm)
• Turn
• Turn signal/ multi-function switch
• Under- hood fuse block (on right side of engine compt)
• Underhood fuse block (on right side of engine compt)
• Underhood fuse block (on right side of engine compt) x3

Exterior Lamps Wiring Diagram (2 of 2) for Chevrolet Corvette 2008

List of elements for Exterior Lamps Wiring Diagram (2 of 2) for Chevrolet Corvette 2008:

• (rear body harness, 11 cm from connector x455 breakout) j459
• (rear body harness, 6.5 cm from connector x455 breakout) j455
• (w/ rear fog lamp)
• Body control module (bcm) (mounted on toe board, in right footwell)
• Cluster/ hud fuse 15a
• Computer data lines system
• D10
• G201 (at base of left "a" pillar)
• G302 (at right "b" pillar, behind trim panel)
• Hazard switch
• Hot at all times
• Hzrd flash sig
• Instrument panel cluster
• Interior lights system
• Ipc
• Ipc class 2 data
• J200
• J457 (rear body harn, 15 cm from conn x455 breakout)
• J931
• Left inner tail/ stop & turn signal lamp (w/o rear fog lamp)
• Left license lamp
• Left outer tail/ stop & turn signal lamp (w/o rear fog lamp)
• Left rear marker lamp
• Left rear turn signal lamp
• Left tail/ stop lamp
• Left turn sig ind
• Logic
• Off
• Power distribution system
• Right inner tail/ stop & turn signal lamp (w/o rear fog lamp)
• Right license lamp
• Right outer tail/ stop & turn signal lamp (w/o rear fog lamp)
• Right rear marker lamp
• Right rear turn signal lamp (w/ rear fog lamp)
• Right tail/ stop lamp (w/ rear fog lamp)
• Right turn sig ind
• Stop lamp relay
• Stp lmp rly ctrl
• Stp lmp sw sig
• Tan
• W/ rear fog lamp
• W/o rear fog lamp

GROUND DISTRIBUTION

Ground Distribution Wiring Diagram (1 of 4) for Chevrolet Corvette 2008

List of elements for Ground Distribution Wiring Diagram (1 of 4) for Chevrolet Corvette 2008:

• (7- speaker system) audio amplifier
• (7- speaker system) left front speaker
• (7- speaker system) right front speaker
• (a/t) automatic transmission
• (if equipped) traffic information receiver
• (not used)
• (w/ digital audio system s-band) digital radio receiver
• (w/ high pressure headlamp washer) hdlp wash relay 46
• (w/ high pressure headlamp washer) headlamp washer fluid pump
• (w/ onstar) vehicle communication interface module (vcim)
• A x1
• A/c compressor clutch
• A12 x1
• Battery
• Body control module (bcm)
• Brake fluid level switch
• C10
• Coupe/ convertible
• Data link connector (dlc)
• Electronic brake control module (ebcm)
• Engine control module (ecm)
• Fan control module
• Front fog lamp relay 38
• Fuel pump relay 55
• G101 (on left frame rail)
• G102 (on top of right frame rail, ground for sp102)
• G104 (on right frame rail, below battery tray)
• G105 (on front left side of engine, above generator)
• G106 (on right rear side of engine, above starter solenoid)
• G107 (left side of engine, middle of block)
• G303 (right "b" pillar)
• Horn assembly
• Ignition coil/ module 1
• Ignition coil/ module 2
• Ignition coil/ module 3
• Ignition coil/ module 4
• Ignition coil/ module 5
• Ignition coil/ module 6
• Ignition coil/ module 7
• Ignition coil/ module 8
• Intake air temperature (iat)/ mass air flow (maf) sensor
• J101 (in forward lamp harness, 10 cm from g101 breakout)
• J102 (in forward lamp harness, 10 cm from horn assembly breakout to cooling fan)
• J106
• J217
• J230 (forward lamp harness, 10 cm from a/c compressor clutch connector breakout)
• J232 (in i/p harness, 3 cm from bcm breakout to sp208)
• Left front fog lamp
• Left front marker lamp
• Left headlamp ballast
• Left headlamp high beam
• Left park/ turn signal lamp
• M14
• Radio
• Remote control door lock receiver (rcdlr)
• Right front fog lamp
• Right front marker lamp
• Right headlamp ballast
• Right headlamp high beam
• Right park/ turn signal lamp
• S x1
• Underhood fuse block (on right side of engine compt)
• Windshield washer fluid level switch
• Windshield washer fluid pump
• Wiper run/acc relay 42
• X400
• Z06 model

Ground Distribution Wiring Diagram (2 of 4) for Chevrolet Corvette 2008

List of elements for Ground Distribution Wiring Diagram (2 of 4) for Chevrolet Corvette 2008:

• (convertible w/o power folding roof) folding top release switch
• (convertible) folding top stowage compartment lid latch release actuator
• (convertible) rear compartment lid lock cylinder key switch
• (coupe) rear compartment lid pulldown actuator
• (w/ accessory, steering wheel control) right steering wheel control switch
• (w/ front seat heater) driver heated seat control module
• (w/ head up display) head up display (hud)
• (w/ memory) driver memory seat adjuster switch
• (w/ memory) driver memory seat module
• (w/ power folding roof- convertible) folding top control switch
• A x2
• B x1
• B x2
• Base
• Coil
• Convertible
• Coupe
• Data link connector (dlc)
• Driver door control module
• Driver door latch
• Driver door lock indicator
• Driver door lock switch
• Driver exterior door handle switch
• Driver interior door handle switch
• Driver outside rearview mirror
• Driver seat adjuster switch
• Driver seat lumbar pump/ control module
• Driver window switch
• Folding top pump/ motor assembly
• Fuel door release actuator
• Fuel door release switch
• G x4
• G201 (at base of left "a" pillar)
• G301 (at left "b" pillar, behind trim panel)
• Hazard warning switch
• Head up display (hud) switch
• Horn switch
• I/p dimmer switch
• Ignition mode switch
• Inflatable restraint steering
• Instrument panel cluster (ipc)
• Interior rear compartment lid release switch
• J200
• J275 (steering column harness, near turn signal/ multifunction switch)
• J301
• J303
• J339 (folding top harness, 7 cm from x431)
• J379 (driver seat harness, 21 cm from x375)
• J539 (drivers door harness, 6.5 cm from connector x555 breakout)
• J579 (driver door harness, 10 cm from door lock switch breakout)
• K x1
• K x3
• Nca
• Rear compartment lid latch
• Rear window defogger grid
• Steering column lock control module
• Turn signal/ multifunction switch
• Uplevel
• Valve 1
• Valve 2
• Valve 3
• W/ head up display
• Wheel module
• Windshield wiper motor
• X1 b
• X276 b
• X277

Ground Distribution Wiring Diagram (3 of 4) for Chevrolet Corvette 2008

List of elements for Ground Distribution Wiring Diagram (3 of 4) for Chevrolet Corvette 2008:

• (convertible) tonneau release relay
• (in right front footwell, mounted to toe board) i/p relay block
• (on right side of engine compt) underhood fuse block
• (w/ magnetic ride control) electronic suspension control (esc) module
• Accessory power outlet
• B x1
• Blower motor control module
• Body control module (bcm)
• Center console flood lamp
• Cigar lighter
• D1 x3
• Driver heated seat switch
• Fuel pump & sender assembly
• G202 (at base of right "a" pillar)
• G401 (at rear of vehicle, on inner side of left frame rail)
• G402 (at rear of vehicle, on inner side of right frame rail)
• Garage door opener
• Hvac control module
• I/p compartment lamp
• Inflatable restraint passenger presence system (pps) module
• Inflatable restraint sensing & diagnostic module (sdm)
• Inside rearview mirror
• J202 (right ignition control module jumper harness, 5.0 cm from connector x110 breakout)
• J216
• J246 (i/p harness, 39.5 cm from inside rearview mirror breakout)
• J400
• J640
• Left vanity mirror lamp
• M10
• M18
• Nca
• Passenger door lock indicator
• Passenger door lock switch
• Passenger door module (pdm)
• Passenger exterior door handle switch
• Passenger heated seat switch
• Passenger interior door handle switch
• Passenger outside rearview mirror
• Passenger window switch
• Right vanity mirror lamp
• Secondary fuel level sensor
• Suspension control switch
• Traction control switch
• W/s wash relay 36
• Wiper hi/lo relay 41
• Wiper on/off relay 45
• X1 a1
• X311 b
• X4 e12

Ground Distribution Wiring Diagram (4 of 4) for Chevrolet Corvette 2008

List of elements for Ground Distribution Wiring Diagram (4 of 4) for Chevrolet Corvette 2008:

• (w/ front seat heater) passenger heated seat module
• (w/ power folding roof- convertible) folding top control module (ftm)
• (w/ power folding roof- convertible) folding top cover pulldown actuator
• (z06 model) exhaust tail pipe flow valve control module
• Center high mounted stop lamp (chmsl)
• Exterior rear compartment lid release switch
• G302 (at right "b" pillar, behind trim panel)
• J302 (i/p harness, 10 cm from passenger door latch breakout)
• J382
• Left back up lamp
• Left inner tail/stop & turn signal lamp
• Left license lamp
• Left outer tail/stop & turn signal lamp
• Left rear marker lamp
• Left rear turn signal lamp
• Left tail/stop lamp
• Nca
• Passenger door latch
• Passenger seat adjuster switch
• Passenger seat lumbar pump/control module
• Right back up lamp
• Right inner tail/stop & turn signal lamp
• Right license lamp
• Right outer tail/stop & turn signal lamp
• Right rear marker lamp
• Right rear turn signal lamp
• X1 b
• X1 k

HEADLIGHTS

Headlights Wiring Diagram for Chevrolet Corvette 2008

List of elements for Headlights Wiring Diagram for Chevrolet Corvette 2008:

• (in right front footwell, mounted to toe board) i/p relay block
• (not used)
• (rear body harness, 6.5 cm from left backup lamp connector breakout) j960
• Air conditioning system
• Auto
• Body control module (bcm) (mounted on toe board, in right footwell)
• C10
• Class 2 (bcm)
• Class 2 ser data
• Computer data lines system
• D10
• F11
• Fog lamp ind
• Fog lmp rly ctrl
• Front fog
• Front fog lmp sw sig
• Frt fog lp fuse 22 15a
• Frt fog lp relay 38
• Ftp
• Ftp sw sig
• G101 (on left frame rail)
• G102 (on top of right frame rail, ground for sp102)
• G201 (at base of left "a" pillar)
• G302 (at right "b" pillar, behind trim panel)
• Head
• Head- lamps on ind
• Headlamp on sig
• Headlamp sw off sig
• Hi beam sig
• Hi bm rly ctrl
• High
• High beam ind
• High beam relay
• Hot at all times
• Hvac control module (center of dash, under radio)
• Instrument panel cluster (ipc)
• J101
• J102
• J119
• J120
• J242 (i/p harness, 35 cm from hvac control module connector)
• J275
• J931
• Lamp switch
• Left front fog lamp
• Left headlamp assembly
• Left headlamp ballast
• Left high beam headlight
• Left rear fog lamp
• Logic
• Low
• Low beam relay
• Low bm rly ctrl
• Low ref
• Lt hi bm fuse 24 10a
• Lt lo bm fuse 21 20a
• Nca
• Off
• Park
• Prk lmp sw on sig
• Rear fog lamp switch
• Rear fog lmp rly ctrl
• Rear fog lmp sw sig
• Rear fog/ aldl/top switch fuse 10a
• Rear/fog relay (if equipped)
• Right front fog lamp
• Right headlamp assembly
• Right headlamp ballast
• Right high beam headlight
• Right rear fog lamp
• Rt hi bm fuse 23 10a
• Rt lo bm fuse 19 20a
• Sen sig
• Ser data
• Ser data class 2
• Sunload sensor assembly (on top left center of dash)
• Turn signal/ multifunction switch
• Underhood fuse block (on right side of engine compt)

HORN

Horn Wiring Diagram for Chevrolet Corvette 2008

List of elements for Horn Wiring Diagram for Chevrolet Corvette 2008:

• A x276
• A10 x1
• A12 x3
• Body control module (bcm) (mounted on toe board, in right footwell)
• G102 (on top of right frame rail, ground for sp102)
• G201 (at base of left "a" pillar)
• Horn assembly (lower right front of vehicle)
• Horn relay 34
• Horn rly ctrl
• Horn switch
• Horn/alt sense fuse 2 15a
• Hot at all times
• Inflatable restraint steering wheel module (center of steering wheel)
• Inflatable restraint steering wheel module coil (center of steering column)
• J102
• Logic
• Tan
• Underhood fuse block (on right side of engine compt)
• X277

INSTRUMENT CLUSTER

Instrument Cluster Wiring Diagram (1 of 2) for Chevrolet Corvette 2008

List of elements for Instrument Cluster Wiring Diagram (1 of 2) for Chevrolet Corvette 2008:

• (left side of dash) head up display (hud) switch
• A12
• A13
• A14
• A16
• Abs ind
• Air bag ind
• B14
• B15
• B16
• Bat + voltage
• Brake fluid level switch (in master cylinder reservoir)
• Brake ind
• Brk fluid lvl sens sig
• Charging gauge
• Class 2 (bcm)
• Class 2 (ecm)
• Class 2 (sdm)
• Computer data lines system
• Coolant temp gauge
• Dic fuel sw sig
• Dic gauges sw sig
• Dic option sw sig
• Dic reset sw sig
• Dic trip sw sig
• Dome lmp sw sig
• Driver information center (dic)
• Driver information center (dic) switch
• Eng spd sig
• Engine speed sig
• Exterior lights system
• Fog lamp ind
• Fuel level gauge
• Fuel switch
• G101 (on left frame rail)
• G201 (at base of left "a" pillar)
• Gauges switch
• Gmlan (ebcm)
• Gmlan (ecm)
• Gnd
• Haz flasher sig
• High beam ind
• Hud dim dn
• Hud dim up
• Hud dn
• Hud up
• I/p dim sw dn sig
• I/p dim sw up sig
• I/p lmp dim ctrl
• I/p lmp sply voltage 2
• Ign
• Illum
• Illumination (3 bulbs)
• Inst panel lmp sply volt
• Instrument panel cluster (ipc)
• Interior lights system
• Ipc
• Ipc class 2 serial data
• J101
• J303
• Km/h ind
• Lamp outage ind
• Left turn ind
• Logic
• Low ref
• Low tire pressure ind
• Malfunction ind
• Mode
• Mph ind
• Oil level gauge
• Oil temp sens sig
• Option switch
• Page
• Park brake switch (lower front of park brake handle)
• Pnk
• Prk brk sw sig
• Prk lmp sply voltage
• Reset switch
• Right turn ind
• Rpm x 1000 gauge
• Seat belt ind
• Security ind
• Speedometer
• Tan
• Traction off ind
• Trip switch
• Turn signal audible ind
• Underhood fuse block (on right side of engine compt) x1
• Upshift ind
• Veh spd sig
• Vehicle speed sig
• W/w fluid lvl sens sig
• Wiper/washer system
• X1 (conn a)
• X2 (conn b)

Instrument Cluster Wiring Diagram (2 of 2) for Chevrolet Corvette 2008

List of elements for Instrument Cluster Wiring Diagram (2 of 2) for Chevrolet Corvette 2008:

• (driver seat harness, 10 cm from seat belt switch)
• (fuel level sensor right harness, 20 cm from connector x460 breakout) j462
• (right ignition control module jumper, 4.0 cm from breakout to ignition coil/module 4)
• (transmission harness, 20 cm from connector x420 breakout) j460
• 5v ref 1
• Bat pos voltage
• Belt switch
• Body control module (bcm) (mounted on toe board, in right footwell)
• Class 2 ser data
• Clstr/ hud fuse 15a
• Computer data lines system
• D10
• Data sig
• Dim up sig
• Driver seat belt switch (in driver's seat belt buckle assembly)
• Ect sig
• Eng speed
• Engine control module (ecm) (behind right front fender, between wheelhouse & dash panel)
• Engine controls system
• Engine coolant temperature (ect) sensor (in front left side of left cylinder head)
• Engine oil level/ temperature sensor (6.2l) (on bottom right center of engine oil pan)
• Engine oil pressure (eop) sensor (6.2l: on top center rear of engine) (7.0l: on top rear of engine)
• Engine oil temperature sensor (7.0l) (on bottom of oil tank)
• Engine spd sig
• From data link connector breakout)
• Fuel level sensor (left)
• Fuel lvl 2
• Fuel lvl sig
• Fuel pump & sender assembly (in left fuel pump assembly)
• G201 (at base of left "a" pillar)
• G401 (at rear of vehicle, on inner side of left frame rail)
• Gnd
• Head up display (hud) (if equipped) (top left side of dash)
• Hot at all times
• Image dn sig
• Image down
• Image up
• Inflatable restraint sensing & diagnostic module (sdm) (behind center of dash, under hvac control head)
• J211
• J221 (i/p harness, 8 cm pnk
• J303
• J391
• J400
• Low ref
• Lvl sw sig
• Mil ctrl
• Nca
• Oil press
• Page sig
• Pnk
• Radio
• Secondary fuel level sensor (in right fuel tank)
• Serial data
• Serial data+
• Serial data-
• Sig dim dn
• Sig image up
• Tan
• Underhood fuse block (on right side of engine compt)
• Vehicle spd sig
• Vss

INTERIOR LIGHTS

Courtesy Lamps Wiring Diagram for Chevrolet Corvette 2008

List of elements for Courtesy Lamps Wiring Diagram for Chevrolet Corvette 2008:

• (i/p harness, 10 cm from blower motor control module breakout) j310
• (i/p harness, 10 cm from flood lamp breakout) j351
• (not used)
• (transmission harness, 11 cm from yaw rate connector) j422
• A10
• Ajar
• Battery+
• Body control module (bcm) (mounted on toe board, in right footwell)
• Computer data lines system
• Convertible
• Coupe
• Courtesy low
• Courtesy v+
• Ctsy lamps +v
• Ctsy/ lamp fuse 10a
• Dome
• Dome switch
• Driver door close latch (in rear of driver door)
• Front passenger close door latch (in rear of passenger door)
• G201 (at base of
• G202 (at base of
• G301 (at left "b" pillar, behind trim panel)
• G302 (at right "b" pillar, behind trim panel)
• Garage door opener (gdo)
• Gnd
• Ground
• Hot at all times
• I/p comp- artment lamp
• I/p dimmer switch
• Inside rearview mirror
• Instrument panel cluster (ipc)
• J301
• J302
• J303
• J312
• J314
• Left "a" pillar)
• Left i/p courtesy lamp
• Left rear compart- ment courtesy lamp
• Left vanity mirror lamp
• Lf door ajar
• Logic
• Open
• Rear compartment lid ajar switch
• Rear compartment lid latch
• Rear compartment lid pull down actuator
• Rf door ajar
• Right "a" pillar)
• Right i/p courtesy lamp
• Right rear compartment courtesy lamp
• Right vanity mirror lamp
• Serial data
• Trunk ajar
• Trunk ajar sw sig
• Trunk lamp ctrl
• Underhood fuse block (on right side of engine compt)
• X1 d2
• X131
• X3 b1

Instrument Illumination Wiring Diagram for Chevrolet Corvette 2008

List of elements for Instrument Illumination Wiring Diagram for Chevrolet Corvette 2008:

• (center of steering column) inflatable restraint steering wheel module coil
• (driver door harness, 10 cm from door lock indicator breakout) j559
• (i/p harness, 22.5 cm from inside rearview mirror breakout) j237
• (i/p harness, 5 cm from blower motor control module connector breakout) j255
• (if equipped) folding top control switch
• (if equipped) head up display (hud) switch
• (in i/p harness, 25 cm from dimmer switch breakout)
• (left side of dash)
• (passenger door harness, 10 cm from door lock indicator) j660
• Auto
• Automatic transmission shift lever (a/t)
• Battery
• Battery+
• Body control module (bcm) (mounted on toe board, in right footwell)
• Btsi sol/str whl lck fuse 10a
• C11
• C11 x4
• C12
• Center console flood lamp
• Clstr/ hud fuse 15a
• Computer data lines system
• Ctsy/ lamp fuse 10a
• D10
• Dic ground
• Dic sw illum
• Dim down switch
• Dim up switch
• Dimmer down
• Dimmer up
• Dome sw
• Dome switch
• Driver door control module (bottom center of driver door)
• Driver door handle switch (interior)
• Driver door lock switch
• Driver heated seat switch
• Driver information center (dic) switch
• Driver memory seat adjuster switch
• Driver window switch
• Fuel door release switch
• G201 (at base of left "a" pillar)
• G202 (at base of right "a" pillar)
• Ground
• Hazard warning switch
• Head
• Horns system
• Hot at all times
• Hvac control module (center of dash, under radio)
• I/p dimmer switch
• Ignition mode switch
• Illum
• Illum (3 bulbs)
• Instrument panel cluster (ipc)
• J200
• J201
• J275
• J303
• J312
• J579
• J680
• Lcd backlight
• Logic
• Nca
• Off
• Panel lamps
• Panel lmp ctrl
• Panel lmps
• Park
• Park lamp
• Park lamp relay 37
• Park lamps
• Park sig
• Passenger door control module (bottom center of passenger door)
• Passenger door handle switch (interior)
• Passenger door lock switch
• Passenger heated seat switch
• Passenger window switch
• Pk lamp fuse 8 10a
• Power distribution system
• Radio
• Rear comp- artment release switch (interior)
• Right steering wheel control switch
• Serial data
• Suspension control switch
• Swc dm fuse 2a
• Tan
• Traction control switch
• Turn signal/ multi-function switch
• Underhood fuse block (on right side of engine compt)
• X276
• X277

MEMORY SYSTEMS

Driver"s Memory Seat Wiring Diagram (1 of 2) for Chevrolet Corvette 2008

List of elements for Driver"s Memory Seat Wiring Diagram (1 of 2) for Chevrolet Corvette 2008:

• 5 volt reference
• A10
• A11
• A12
• A13
• A14
• A15
• A16
• B10
• B11
• B12
• B13
• B14
• B15
• B16
• Battery positive voltage
• Body control module (bcm) (mounted on toe board, in right footwell)
• Class 2 serial data
• Column telescope forward control
• Column telescope forward sw
• Column telescope reverse control
• Column telescope reverse sw
• Column telescope sensor sig
• Computer data lines system
• Driver 1
• Driver 2
• Driver memory seat adjuster switch
• Driver memory seat module (under center of drivers seat)
• Driver window switch
• Exit switch
• Front vertical down switch signal
• Front vertical motor down control
• Front vertical motor up control
• Front vertical position sens
• Front vertical up switch signal
• G201 (at base of left "a" pillar)
• G301 (at left "b" pillar, behind trim panel)
• Ground
• Horizontal forward switch signal
• Horizontal motor forward ctrl
• Horizontal motor rearward control
• Horizontal position sens
• Horizontal rearward switch signal
• Hot at all times
• I/p fuse block (in right front footwell, mounted to toe board)
• Illum
• Interior lights system
• J379 (uplevel)
• J393
• J579
• Logic
• Low reference
• Memory 1 switch sig
• Memory 2 switch sig
• Pnk
• Power distribution system
• Pwr seats msm circuit breaker 30a
• Rear vertical down switch signal
• Rear vertical motor down control
• Rear vertical motor up control
• Rear vertical position sens
• Rear vertical up switch signal
• Steering column memory circuit
• Tan
• Tele swtch/ msm fuse 10a

Driver"s Memory Seat Wiring Diagram (2 of 2) for Chevrolet Corvette 2008

List of elements for Driver"s Memory Seat Wiring Diagram (2 of 2) for Chevrolet Corvette 2008:

• Driver seat adjuster motor assembly
• Driver seat adjuster switch
• Front down
• Front up
• Front vertical motor
• Front vertical position sensor
• Horizontal forward
• Horizontal motor
• Horizontal position sensor
• Horizontal rearward
• J395 (driver seat harness, 4 cm from lumbar pump/control module assembly breakout)
• J397 (driver seat harness, 5 cm from seat adjuster motor assembly breakout)
• Nca
• Rear down
• Rear up
• Rear vertical motor
• Rear vertical position sensor
• Steering column telescope actuator (left side of steering column, behind knee bolster)
• Tan

Memory Mirrors Wiring Diagram for Chevrolet Corvette 2008

List of elements for Memory Mirrors Wiring Diagram for Chevrolet Corvette 2008:

• 5v reference
• Battery b+
• Class 2 serial data
• Computer data lines system
• Down directional sw
• Driver 1
• Driver 2
• Driver door control module (ddm) (bottom center of driver door)
• Driver memory seat adjuster switch
• Driver outside rearview mirror
• Driver window switch
• Exit switch
• Front passenger door control module (fpdm) (bottom center of passenger door)
• G201 (at base of left "a" pillar)
• G202 (at base of right "a" pillar)
• Ground
• Horiz posit sensor
• Horizontal motor
• Horizontal position sensor
• Hot at all times
• I/p fuse block (in right front footwell, mounted to toe board)
• Illum
• Interior lights system
• J234
• J579
• Left directional sw
• Left mirror select
• Logic
• Low reference
• Memory 1 sw sig
• Memory 2 sw sig
• Mirror mtr down ctrl
• Mirror mtr left ctrl
• Mirror mtr right ctrl
• Mirror mtr up ctrl
• Nca
• Passenger outside rearview mirror
• Pwr/wndws trunk/fuel relse circuit breaker 30a
• Right directional sw
• Right mirror select
• Tan
• Up directional sw
• Vertical motor
• Vertical posit sensor
• Vertical position sensor

Steering Column Memory Wiring Diagram for Chevrolet Corvette 2008

List of elements for Steering Column Memory Wiring Diagram for Chevrolet Corvette 2008:

• (driver seat harness, 4 cm from lumbar pump/control module assembly breakout)
• 5 volt reference
• A10
• A13
• A15
• B15
• Battery b+
• Body control module (bcm) (mounted on toe board, in right footwell)
• Class 2 serial data
• Computer data lines system
• Driver 1
• Driver 2
• Driver memory seat adjuster switch
• Driver memory seat module (under center of drivers seat)
• Driver window switch
• Exit switch
• G201 (at base of left "a" pillar)
• G301 (at left "b" pillar, behind trim panel)
• Ground
• Hot at all times
• I/p fuse block (in right front footwell, mounted to toe board)
• Illum
• Interior lights system
• J379 (uplevel)
• J395
• J397 (driver seat harness, 5 cm from seat adjuster motor assembly breakout)
• J579
• Logic
• Low reference
• Memory 1 switch sig
• Memory 2 switch sig
• Memory seats circuit
• Nca
• Pnk
• Power distribution system
• Pwr seats msm circuit breaker 30a
• Red
• Steering column telescope actuator (left side of steering column, behind knee bolster)
• Steering column telescope switch (right side of steering column)
• Tan
• Tele sw/msm fuse 10a
• Telescope forward ctrl
• Telescope forward sig
• Telescope in
• Telescope out
• Telescope reverse ctrl
• Telescope reverse sig
• Telescope sensor sig

NAVIGATION

Navigation Wiring Diagram for Chevrolet Corvette 2008

List of elements for Navigation Wiring Diagram for Chevrolet Corvette 2008:

• (in instrument panel harness, 7.5 cm (6.9 in) front folding top 5 bow switches breakout)
• (or nca)
• A12
• Battery
• Body control module (bcm) (mounted on toe board, in right footwell)
• Cellular telephone microphone (upper left ``a" pillar)
• Class 2 serial data
• Coax
• Common sig
• Computer data lines system
• Drain
• Drain wire
• G104 (on right frame rail, below battery tray)
• Ground
• Hot at all times
• J217
• J308 (in instrument panel harness, approxi- mately 24 cm (9 in) from center console flood lamp breakout)
• J309
• J311
• J316 (in instrument panel harness)
• J317
• Low ref drain
• Navigation antenna
• Nca
• Pnk
• Radio
• Rdo/ s-band/ vics fuse 15a
• Rec aud sig
• Rec low ref
• Signal
• Vehicle communication interface module (vcim) (if equipped) (in right rear compt)
• Voice rec aud sig
• W/ communication system
• W/o communication system

POWER DISTRIBUTION

Power Distribution Wiring Diagram (1 of 4) for Chevrolet Corvette 2008

List of elements for Power Distribution Wiring Diagram (1 of 4) for Chevrolet Corvette 2008:

• (6 cm from ebcm breakout)
• (on right side of engine compt) underhood fuse block
• A x1
• A/c comp fuse 15 10a
• A/c comp relay 35
• A18
• A19
• A2 x2
• Abs fuse 27 60a
• Amp fuse 31 30a
• Audio amplifier
• Automatic transmission (a/t)
• Batt 1 fuse 33 60a
• Batt 2 fuse 29 30a
• Battery
• Blower motor control module
• Bose
• C14
• Coolfan fuse 25 60a
• Crank relay 43
• D11
• Delphi
• Driver door control module
• Driver heated seat module (w/ front heated seats)
• Driver memory seat module (w/ memory)
• Driver seat adjuster switch (w/o memory)
• Driver seat lumbar pump/ control module
• Driver seat lumbar switch
• Drvr htd seat fuse 20a
• E x1
• Ecm/tcm/easy key fuse 11 15a
• Electronic brake control module (ebcm)
• Electronic suspension control (esc) module (w/ magnetic ride control)
• Engine control module (ecm)
• Evaporative emission (evap) canister vent solenoid valve
• F12 x3
• Fan control module
• Folding top module (ftm) (w/ power folding roof)
• Frt fog lp fuse 22 15a
• Frt fog lp relay 38
• Fuel door relse relay
• Fuel pump fuse 20 20a
• Fuel pump relay 55
• Generator
• H x1
• H13
• H14
• Hdlp wash fuse 18 20a
• Hdlp wash relay 46
• High beam relay 39
• Horn relay 34
• Horn/ alt sense fuse 2 15a
• Hvac fuse 28 40a
• I/p fuse block (in right front footwell, mounted to toe board)
• I/p relay block (in right front footwell, mounted to toe board)
• J203
• J234 (11.5 cm from the main harn, leading to pcm)
• J380
• J399
• K10
• K14
• Left front speaker
• Low beam relay 47
• Mrrtd fuse 13 25a
• Nca
• Park/pos lamp relay 37
• Pass htd seat fuse 20a
• Passenger door control module
• Passenger heated seat module (w/ front heated seats)
• Passenger seat adjuster switch (if equipped)
• Passenger seat lumbar pump/ control module
• Passenger seat lumbar switch
• Pk lamps fuse 8 10a
• Powertrain ign 1 relay 44
• Prw/wndws trunk/fuel relse circuit breaker 30a
• Pwr seats msm circuit breaker 30a
• Rear defog relay 40
• Red
• Red j195
• Remote control door lock receiver (rcdlr)
• Reverse lockout solenoid (m/t)
• Right front speaker
• Starter
• Starter fuse 30 40a
• To batt 3 fuse 26 (diagram 2 of 4)
• To i/p fuse block (diagram 3 of 4)
• W/s wash fuse 17 15a
• W/s wash relay 36
• Wiper fuse 4 30a
• Wiper on/off relay 45
• Wiper run/acc relay 42
• X3 d11
• X4 a2
• X4 b1

Power Distribution Wiring Diagram (2 of 4) for Chevrolet Corvette 2008

List of elements for Power Distribution Wiring Diagram (2 of 4) for Chevrolet Corvette 2008:

• (39 cm from the hvac control module connector) j231
• (5.0 cm from connector x109 breakout) j208
• (a/t)
• (mounted on toe board, in right footwell) body control module (bcm)
• A6 x3
• A7 x2
• A8 x2
• A8 x3
• Automatic transmission shift lever (a/t)
• B x1
• B1 x1
• B11 x3
• Batt 3 fuse 26 60a
• Bck/up lamp relay
• Btsi sol/str whl lck fuse 10a
• C1 x4
• Clstr/hud fuse 15a
• Cruise switch fuse 2a
• Ctsy/ lamp fuse 10a
• D1 x3
• D10
• D4 x3
• D8 x4
• Data link connector
• Digital radio receiver
• Diode
• Dr lck fuse 15a
• Driver door unlatch pcb relay
• Driver heated seat control module (w/ front heated seats)
• E10 x4
• E11 x3
• Exh mdl fuse 10a
• Exhaust tail pipe flow valve control module (z06 model)
• F19
• F4 (not used)
• F6 x4
• Folding top control switch (w/ power folding roof)
• From batt 1 fuse (diagram 1 of 4)
• G19
• Head up display (hud) (if equipped)
• Htd seat/ wpr rly fuse 10a
• Hvac control module
• Hvac/ pwr snd fuse 10a
• I/p relay block (in right front footwell, mounted to toe board)
• Inadvertent load control pcb relay
• Inflatable restraint steering wheel module coil
• Inside air temperature sensor
• Inside rearview mirror
• Instrument panel cluster (ipc)
• Isrvm/ hvac fuse 10a
• K15
• Left automatic transmission manual shift switch
• Logic
• Nca
• Passenger door unlatch pcb relay
• Passenger heated seat control module (w/ front heated seats)
• Pnk
• Radio
• Radio/s-band/ vics fuse 15a
• Rear fog/ aldl/top switch fuse 10a
• Rly ctrl
• Run crnk relay
• Steering column lock control module (if equipped)
• Steering column lock control module (m/t)
• Stop lamp relay
• Stop/b/u/ lamps fuse 5 15a
• To batt 5 fuse 7 (diagram 3 of 4)
• To gmlan run/crnk fuse (diagram 3 of 4)
• Tonneau release fuse 10a
• Tonneau release relay
• Traffic information receiver
• Turn signal/ multi-function switch
• Underhood fuse block (on right side of engine compt)
• W/ digital radio
• W/o digital radio
• Wiper run/ acc relay 42
• Wiper/ washer system
• X276 c
• X277
• X3 c3

Power Distribution Wiring Diagram (3 of 4) for Chevrolet Corvette 2008

List of elements for Power Distribution Wiring Diagram (3 of 4) for Chevrolet Corvette 2008:

• (in right front footwell, mounted to toe board) i/p fuse block
• (mounted on toe board, in right footwell) body control module (bcm)
• (not used)
• A1 x4
• Abs/mrrtd fuse 3 10a
• Automatic transmission (a/t)
• Aux pwr fuse 20a
• Auxiliary power outlet (left front of center console)
• B10
• B11 x2
• B12 x3
• B5 x3
• Batt 5 fuse 7 30a
• C10
• C5 x3
• C5 x4
• Cigar lighter
• Coupe
• D11 x3
• D12
• Driv dr switch fuse 10a
• Driver memory seat module (w/ memory)
• Driver seat adjuster switch
• Driver window switch
• E11
• Ecm fuse 15a
• Electronic brake control module (ebcm)
• Electronic suspension control (esc) module (w/ magnetic ride control)
• Engine control module (ecm)
• Except coupe
• F11
• Folding top cover pulldown actuator (w/ power folding roof)
• From batt 1 fuse 33 (diagram 1 of 4)
• From htd seat/ d wpr rly fuse (diagram 2 of 4)
• From stop/ b/u/lamps fuse 5 (diagram 2 of 4)
• G202 (at base of right "a" pillar)
• Gmlan run/crnk fuse 20a
• I/p relay block (in right front footwell, mounted to toe board)
• Ignition sw/ intr sens fuse 10a
• Inflatable restraint front passenger presence system (pps) module
• Inflatable restraint sensing & diagnostic module (sdm)
• J246
• J393
• Logic
• Ltr fuse 20a
• Nca
• Onstar fuse 10a
• Pnk
• Rear compartment lid pulldown actuator
• Sdm/aos switch air bag fuse 10a
• Steering column telescope switch (if equipped)
• Tcm/trans fuse 1 10a
• Tele switch/msm fuse 10a
• To ignition mode switch (diagram 4 of 4)
• Tpa fuse 20a
• Trunk relse fuse 15a
• Trunk relse relay
• Underhood fuse block (on right side of engine compt)
• Vehicle communication interface module (vcim) (w/ onstar)

Power Distribution Wiring Diagram (4 of 4) for Chevrolet Corvette 2008

List of elements for Power Distribution Wiring Diagram (4 of 4) for Chevrolet Corvette 2008:

• Acc ind
• Acc ind ctrl
• Back up keyless entry antenna
• Back up sig
• Body control module (bcm) (mounted on toe board, in right footwell)
• From body control module (diagram 3 of 4)
• Gnd
• Ign 1 volt
• Ign 1 voltage
• Ign data sig
• Ignition mode switch
• Interior lights system
• Left keyless entry antenna
• Left sig
• Logic
• Low ref
• Off
• Off ind
• Off ind ctrl
• Pnk
• Rear compartment keyless entry antenna
• Remote control door lock receiver (rcdlr) (right side of dash)
• Right keyless entry antenna
• Right sig
• Sig
• Start
• Start ind
• Start ind ctrl
• Tan

POWER DOOR LOCKS

Power Door Locks Wiring Diagram (1 of 2) for Chevrolet Corvette 2008

List of elements for Power Door Locks Wiring Diagram (1 of 2) for Chevrolet Corvette 2008:

• (in i/p harness, left of audio amplifier) jx208
• (in i/p harness, left of steering column) jx205
• A/t shft lk ctrl
• Ajar
• Backup keyless entry antenna (right side of dash)
• Battery
• Closed
• D11
• Data link connector (dlc) (under dash, below steering column)
• Door ajar sw
• Door latch
• Door open sw
• Dr lk act ctrl
• Driver door latch (in rear of driver door)
• Dvr dr lk act
• Ecm/tcm/ easy key fuse 11 15a
• Exterior lights system
• Front passenger door latch (in rear of passenger door)
• G104 (on right frame rail, below battery tray)
• G301 (at left "b" pillar, behind trim panel)
• G302 (at right "b" pillar, behind trim panel)
• Ground
• Hot at all times
• Ign 1 volt
• Ign mod data
• Ignition mode switch
• J232
• J301
• J302
• K/e ant b-u sig
• K/e b-u low ref
• K/e left low ref
• K/e left sig
• K/e rear compt sig
• K/e right sig
• K/e rt low ref
• Left frnt int dr
• Left keyless entry antenna (top of left "b" pillar)
• Lf frt ext dr
• Open
• Pnk
• Rear compartment keyless entry antenna (below rear compt pull down actuator)
• Rear compt lo ref
• Remote control door lock receiver (rcdlr) (right side of dash)
• Rfa class 2 data
• Right keyless entry antenna (top of right "b" pillar)
• Rt frnt int dr
• Rt frt ext dr
• Shift interlock system
• Tan
• Trunk rel sw sig
• Trunk, tailgate, fuel doors system
• Underhood fuse block (on right side of engine compt)
• X2 a

Power Door Locks Wiring Diagram (2 of 2) for Chevrolet Corvette 2008

List of elements for Power Door Locks Wiring Diagram (2 of 2) for Chevrolet Corvette 2008:

• Battery
• Body control module (bcm) (mounted on toe board, in right footwell)
• Class 2 (bcm)
• Class 2 data
• Convertible
• Coupe
• Door latch ctrl
• Dr ajar sw sig
• Dr lck fuse 15a
• Dr lock ind
• Dr open sw sig
• Driv dr switch fuse 10a
• Driver door control module (ddm) (bottom center of driver door)
• Driver door lock indicator (in upper rear of driver door trim panel)
• Driver door lock switch
• Driver door unlatch pcb relay
• Driver exterior door handle switch (in upper rear of driver door)
• Driver interior door handle switch (in center of driver door panel)
• Driver window switch
• Front passenger door lock switch
• G201 (at base of left "a" pillar)
• G202 (at base of right "a" pillar)
• Ground
• Handle sw sig
• Headlights system
• Horn rel cntrl
• Horns system
• Hot at all times
• Ign
• Ign 1 volt
• Ign switch/ intr snsr fuse 10a
• Instrument panel cluster (ipc)
• Interior lights system
• Ipc class 2 serial data
• J539
• J579
• J640
• J680
• Lcd lamp
• Lock
• Lock cntrl
• Lock sig
• Logic
• Memory 1
• Memory 2
• Memory systems
• Nca
• Passenger door control module (fpdm) (bottom center of passenger door)
• Passenger door lock indicator (in upper rear of passenger door trim panel)
• Passenger door unlatch pcb relay
• Passenger exterior door handle switch (in upper rear of passenger door)
• Passenger interior door handle switch (in center of passenger door panel)
• Pk lamp rel
• Pnk
• Rear compartment lid latch assembly
• Rear compartment lid pulldown actuator
• Security ind
• Serial data
• Tan
• Trk ajar sw sig
• Un- lock
• Unlock cntrl
• Unlock sig

POWER MIRRORS

Automatic Day/Night Mirror Wiring Diagram for Chevrolet Corvette 2008

List of elements for Automatic Day/Night Mirror Wiring Diagram for Chevrolet Corvette 2008:

• (at base of right "a" pillar) g202
• Ambient light sensor ind
• Automatic day/night mirror
• Back-up lamp pwr
• Bck/up lamp relay
• Body control module (bcm) (mounted on toe board, in right footwell)
• Button back lighting
• Day/night mirror low ref
• Day/night mirror sig
• Driver outside rearview mirror
• Driver outside rearview mirror glass
• Emergency ind
• Emergency switch
• Gnd
• Headlight sensor ind
• Hot at all times
• Ign 1 volt
• Inside rearview mirror
• Interior lights system
• Isrvm/ hvac fuse 10a
• J231
• J312
• Keypad green led ind
• Keypad green led sig
• Keypad red led ind
• Keypad red led sig
• Keypad sig
• Keypad sply volt
• Left
• Logic
• Nca
• Onstar button assembly
• Onstar ind
• Onstar switch
• Passenger air bag off ind
• Passenger air bag on ind
• Phone ind
• Phone switch
• Pnk
• Reverse lamp rly ctrl
• Reverse lamps fuse 10a
• Right
• Run/ crank rly ctrl
• Run/ crnk relay
• Vehicle communication interface module (vcim) (w/ onstar) (in right rear compt)

Power Mirror Wiring Diagram for Chevrolet Corvette 2008

List of elements for Power Mirror Wiring Diagram for Chevrolet Corvette 2008:

• 5v reference
• Automatic day/night mirror circuit
• Battery b+
• Class 2 serial data
• Computer data lines system
• Defogger system
• Down directional sw
• Driver door control module (ddm) (bottom center of driver door)
• Driver outside rearview mirror
• Driver outside rearview mirror glass
• Driver window switch
• Front passenger door module (fpdm) (bottom center of passenger door)
• G201 (at base of left "a" pillar)
• G202 (at base of right "a" pillar)
• Ground
• Horiz posit sensor
• Horizontal motor
• Horizontal position sensor
• Hot at all times
• I/p fuse block (in right front footwell, mounted to toe board)
• J234
• Left directional sw
• Left mirror select
• Logic
• Low reference
• Mirror mtr down ctrl
• Mirror mtr left ctrl
• Mirror mtr right ctrl
• Mirror mtr up ctrl
• Nca
• Passenger outside rearview mirror
• Passenger outside rearview mirror glass
• Pnk
• Pwr/wndws trunk/fuel relse circuit breaker 30a
• Right directional sw
• Right mirror select
• Tan
• Up directional sw
• Vertical motor
• Vertical posit sensor
• Vertical position sensor

POWER SEATS

Driver Seat Wiring Diagram for Chevrolet Corvette 2008

List of elements for Driver Seat Wiring Diagram for Chevrolet Corvette 2008:

• Driver seat adjuster motor assembly
• Driver seat adjuster switch
• Dwn
• Front vertical motor
• Frt dn
• Frt up
• Fwd
• G301 (at left "b" pillar, behind trim panel)
• Horizontal motor
• Hot at all times
• I/p fuse block (in right front footwell, mounted to toe board)
• J379 (uplevel)
• Nca
• Pwr seats msm circuit breaker 30a
• Rear vertical motor
• Rr dn
• Rr up
• Rwd
• Tan

Heated Seats Wiring Diagram for Chevrolet Corvette 2008

List of elements for Heated Seats Wiring Diagram for Chevrolet Corvette 2008:

• (at base of right "a" pillar) g202
• Battery
• Body control module (bcm) (mounted on toe board, in right footwell)
• Driver heated seat back element (under center of driver seat back)
• Driver heated seat cushion element (under the center of driver seat cushion)
• Driver heated seat module (under center of driver seat)
• Driver heated seat switch
• Drvr htd seat fuse 20a
• Element ctrl
• G202 (at base of right "a" pillar)
• G301 (at left "b" pillar, behind trim panel)
• G302 (at right "b" pillar, behind trim panel)
• Ground
• Hi temp ind
• Hi/lo
• Hi/low sig
• High
• Hot at all times
• Htd seat/ wpr rly fuse 10a
• Hvac control module (center of dash, under radio)
• I/p fuse block (in right front footwell, mounted to toe board)
• Ign 1 volt
• Illum
• Inhibit sig
• Interior lights system
• J246
• J304
• J305
• J306
• J307
• J379 (up level)
• J380
• J382
• J399
• Logic
• Low
• Low temp ind
• Nca
• Off
• Off sig
• Pass htd seat fuse 20a
• Passenger heated seat back element (under center of passenger seat back)
• Passenger heated seat cushion element (under center of passenger seat cushion)
• Passenger heated seat module (under center of passenger seat)
• Passenger heated seat switch
• Pnk
• Run crnk relay
• Sens low ref
• Sply volt
• Status sig
• Temp ctrl sig
• Temp sens sig

Lumbar Wiring Diagram for Chevrolet Corvette 2008

List of elements for Lumbar Wiring Diagram for Chevrolet Corvette 2008:

• Batt
• Bolster deflate ctrl
• Bolster inflate ctrl
• Driver seat lumbar pump/ control module (under center of passenger seat)
• Driver seat lumbar switch (front left side of driver seat)
• Drvr htd seat fuse 20a
• G301 (at left "b" pillar, behind trim panel)
• G302 (at right "b" pillar, behind trim panel)
• Ground
• Hot at all times
• I/p fuse block (in right front footwell, mounted to toe board)
• J379 (up level)
• J380
• J382
• J399
• Lumbar deflate ctrl
• Lumbar inflate ctrl
• Nca
• Pass htd seat fuse 20a
• Passenger seat lumbar pump/ control module (under center of passenger seat)
• Passenger seat lumbar switch (front left side of passenger seat)
• Pnk

Passenger Seat Wiring Diagram for Chevrolet Corvette 2008

List of elements for Passenger Seat Wiring Diagram for Chevrolet Corvette 2008:

• Dwn
• Front vertical motor
• Frt dn
• Frt up
• Fwd
• G302 (at right "b" pillar, behind trim panel)
• Horizontal motor
• Hot at all times
• I/p fuse block (in right front footwell, mounted to toe board)
• J382
• Nca
• Passenger seat adjuster motor assembly
• Passenger seat adjuster switch
• Pwr seats msm circuit breaker 30a
• Rear vertical motor
• Rr dn
• Rr up
• Rwd
• Tan

POWER TOP/SUNROOF

Convertible Top Wiring Diagram, with Manual Top for Chevrolet Corvette 2008

List of elements for Convertible Top Wiring Diagram, with Manual Top for Chevrolet Corvette 2008:

• (at left "b" pillar, behind trim panel)
• (not used)
• 10a
• Acc voltage
• Batt 3 fuse 26 60a
• Bcm class 2 serial data
• Body control module (bcm) (mounted on toe board, in right footwell)
• Computer data lines system
• Connected signal
• Driver information center
• Folding top front latch switch (in upper windshield frame support)
• Folding top release switch
• Folding top stowage compartment lid latch release actuator
• G202 (at base of right "a" pillar)
• G301
• Hot at all times
• I/p relay block (in right front footwell, mounted to toe board)
• Instrument panel cluster (ipc)
• J208
• J216
• J301
• Logic
• Nca
• Release fuse
• Release sw sply volt
• Serial data
• Tonneau
• Tonneau release relay
• Top cover ajar switch
• Top cover release relay
• Underhood fuse block (on right side of engine compartment)

Convertible Top Wiring Diagram, with Power Top (1 of 2) for Chevrolet Corvette 2008

List of elements for Convertible Top Wiring Diagram, with Power Top (1 of 2) for Chevrolet Corvette 2008:

• (not used) x433
• 5 bow lowered sw sig
• 5 bow raised sw sig
• 5v low reference
• A10
• A11
• A12
• A13
• A14
• A15
• A16
• Accessory voltage
• B10
• B11
• B12
• B13
• B14
• B15
• B16
• Batt 2 fuse 29 30a
• Battery positive voltage
• Class 2 serial data
• Close
• Computer data lines system
• Driver information center (dic)
• Fold top control switch close signal
• Fold top control switch open signal
• Folding top connected signal
• Folding top control module (ftm) (between driver & passenger seat, mounted on bracket below tonneau latch actuator)
• Folding top control switch (left side of dash)
• Folding top cover open sw sig
• G302 (at right "b" pillar, behind trim panel)
• Ground
• Hot at all times
• Instrument panel cluster (ipc)
• Interior lights system
• Ipc class 2 serial data
• J302
• Logic
• Luggage barrier switch sig
• Open
• Pump direction a
• Pump direction b
• Tan
• Thermal sensor signal
• Top closed switch
• Top open switch
• Underhood fuse block (on right side of engine compartment)
• Valve 1 control
• Valve 2 control
• Valve 3 control

Convertible Top Wiring Diagram, with Power Top (2 of 2) for Chevrolet Corvette 2008

List of elements for Convertible Top Wiring Diagram, with Power Top (2 of 2) for Chevrolet Corvette 2008:

• (at left "b" pillar, behind trim panel) g301
• (folding top harness, 17.5 cm from 5 bow switches breakout) j333
• (i/p harness, 16 cm from folding top cover latch actuator breakout) j355
• (not used)
• Acc volt
• Body control module (bcm) (mounted on toe board, in right footwell)
• Down
• Extend up
• F9 x4
• Folding top 5 bow lowered switch (under headliner, on folding top hinge)
• Folding top 5 bow raised switch (under headliner, on folding top hinge)
• Folding top closed position switch (under center of folding top cover)
• Folding top connected signal
• Folding top cover ajar switch
• Folding top cover release relay control
• Folding top front latch switch (in upper windshield frame support)
• Folding top luggage barrier switch (right rear of rear compt lid, near right hinge)
• Folding top open position switch (under center of folding top cover on pulldown actuator)
• Folding top pump/motor
• Folding top pump/motor assembly
• Folding top stowage compartment lid latch pulldown actuator
• Folding top stowage compartment lid latch release actuator
• Folding top stowage compartment lid release switch
• G202 (at base of right "a" pillar)
• G301 (at left "b" pillar, behind trim panel)
• G302 (at right "b" pillar, behind trim panel)
• Hot at all times
• I/p relay block (in right front footwell, mounted to toe board)
• J216
• J301
• J302
• J339
• Logic
• Nca
• Pull down ajar sig
• Rear fog/ aldl/top swtch fuse 10a
• Retract down
• S334
• Sound systems
• Tan
• Thermal
• Tonneau release relay
• Tonneau relse fuse 10a
• Tpa fuse 20a
• Valve 1
• Valve 2
• Valve 3
• X3 d11

POWER WINDOWS

Power Windows Wiring Diagram for Chevrolet Corvette 2008

List of elements for Power Windows Wiring Diagram for Chevrolet Corvette 2008:

• (bottom center of driver door) driver door control module
• Body control module (bcm) (mounted on toe board, in right footwell)
• Computer data lines system
• Ddm class 2 ser data
• Driv dr swtch fuse 10a
• Driver window motor (lower section of door)
• Driver window switch
• Driver wndo down signal
• Driver wndo express sig
• Driver wndo up signal
• Express up/down
• G201 (at base of left "a" pillar)
• G202 (at base of right "a" pillar)
• Ground
• Hot at all times
• I/p fuse block (in right front footwell, mounted to toe board)
• Interior lights system
• J234
• J579
• J680
• Logic
• Pass wndo down signal
• Pass wndo express sig
• Pass wndo up signal
• Passenger door control module (bottom center of passenger door)
• Passenger window motor (lower section of door)
• Passenger window switch
• Pdm class 2 ser data
• Power window motor fr passenger down sig
• Power window motor front passenger up sig
• Power window motor lt front down control
• Power window motor lt front up control
• Power window motor rt front down control
• Power window motor rt front up control
• Power window switch rt front express sig
• Prw/wndws trunk/fuel relse circuit breaker 30a
• Serial data
• Tan

RADIO

Base Radio Wiring Diagram for Chevrolet Corvette 2008

List of elements for Base Radio Wiring Diagram for Chevrolet Corvette 2008:

• (or 9705)
• (w/ onstar)
• (w/o onstar)
• A10
• A11
• A12
• Amp fuse 31 30a
• Amp mute sig
• Amplifier mute sig
• Ant enable sig
• Ant enbl sig
• Antenna sig
• Audio amplifier (right footwell, mounted on toe board)
• Audio common
• Audio common sig
• B10
• B11
• B12
• Battery
• Body control module (bcm) (mounted on toe board, in right footwell)
• Center i/p speaker
• Class 2 serial data
• Coax
• Computer data lines system
• Drain wire
• F center out (+)
• F center out (-)
• Fm composite sig
• G104 (on right frame rail, below battery tray)
• Ground
• Hot at all times
• Inflatable restraint steering wheel module coil (center of steering column)
• J204
• J205
• J217
• J313
• L audio sig
• L audio sig (+)
• Left front speaker
• Left front subwoofer speaker
• Left radio antenna
• Left radio antenna module (left side of rear compt)
• Left rear speaker
• Lf low level sig (+)
• Lf low level sig (-)
• Lf mid spkr out (+)
• Lf mid spkr out (-)
• Lf sbwfr spkr out (+)
• Lf sbwfr spkr out (-)
• Low ref
• Lr low level sig (+)
• Lr low level sig (-)
• Lr mid spkr out (+)
• Lr mid spkr out (-)
• Lt antenna sig am
• Lt antenna sig fm1
• Mute
• Navigation antenna
• Navigation system
• Nca
• Pnk
• R audio sig (+)
• Radio
• Radio ant mod
• Radio ctrl sply vol
• Radio mod sig
• Rdo/ s-band/ vics fuse 15a
• Red
• Rf low level sig (+)
• Rf low level sig (-)
• Rf mid spkr out (+)
• Rf mid spkr out (-)
• Rf sbwfr spkr out (+)
• Rf sbwfr spkr out (-)
• Right front speaker
• Right front subwoofer speaker
• Right radio antenna
• Right radio antenna module (right side of rear compt)
• Right rear speaker
• Right steering wheel control switch
• Rr low lev aud sig (-)
• Rr low level sig (+)
• Rr low level sig (-)
• Rr mid spkr out (+)
• Rr mid spkr out (-)
• Satellite radio circuit
• Strg wheel ctrl sig
• Tan
• Underhood fuse block (on right side of engine compt)
• Vehicle communication interface module (vcim) (if equipped) (in right rear compt)
• Voice rec aud sig
• Vol dn
• Vol up
• X276
• X277

Premium Sound Radio Wiring Diagram for Chevrolet Corvette 2008

List of elements for Premium Sound Radio Wiring Diagram for Chevrolet Corvette 2008:

• (coupe)
• (left side of dash, right of steering column) noise compensation microphone
• (or 9705)
• (w/ onstar)
• (w/o onstar)
• A10
• A11
• A12
• Amp fuse 31 30a
• Amp mute sig
• Ant enable sig
• Ant enbl sig
• Ant sig
• Antenna sig
• Audio amplifier (right footwell, mounted on toe board)
• Audio common
• Audio common sig
• B10
• B11
• B12
• Battery
• Body control module (bcm) (mounted on toe board, in right footwell)
• Center i/p speaker
• Class 2 serial data
• Coax
• Computer data lines system
• Convertible
• Drain
• Drain wire
• E (convertible)
• Fm composite sig
• Frt cntr spkr out (+)
• Frt cntr spkr out (-)
• G104 (on right frame rail, below battery tray)
• Gnd
• Ground
• Hot at all times
• Inflatable restraint steering wheel module coil (center of steering column)
• Instrument cluster system
• J203
• J204
• J205
• J206
• J207 nca
• J209
• J210
• J217
• J230
• J313
• L audio sig
• L audio sig (+)
• Left front speaker
• Left radio antenna
• Left radio antenna module (left side of rear compt)
• Left rear speaker
• Left speaker
• Lf low level sig (+)
• Lf low level sig (-)
• Lf mid spkr out (+)
• Lf mid spkr out (-)
• Lf sbwfr spkr out (+)
• Lf sbwfr spkr out (-)
• Low ref
• Lr low level sig (+)
• Lr low level sig (-)
• Lt antenna sig am
• Lt antenna sig fm1
• Mute
• Navigation antenna
• Navigation system
• Nca
• Noise comp enbl sig
• Noise comp mic pwr
• Out +
• Out -
• Pnk
• Power tops system
• R audio sig (+)
• Radio
• Radio ant mod
• Radio ctrl sply vol
• Radio mod sig
• Rdo/ s-band/ vics fuse 15a
• Rear spkr out (+)
• Rear spkr out (-)
• Red
• Rf low level sig (+)
• Rf low level sig (-)
• Rf mid spkr out (+)
• Rf mid spkr out (-)
• Rf sbwfr spkr out (+)
• Rf sbwfr spkr out (-)
• Right front speaker
• Right radio antenna
• Right radio antenna module (right side of rear compt)
• Right rear speaker
• Right speaker
• Right steering wheel control switch
• Rr low level sig (+)
• Rr low level sig (-)
• Satellite radio circuit
• Strg wheel ctrl sig
• Tan
• Underhood fuse block (on right side of engine compt)
• Vehicle communication interface module (vcim) (if equipped) (in right rear compt)
• Voice rec aud sig
• Vol dn
• Vol up
• Vss
• X276
• X277

Satellite Radio Wiring Diagram for Chevrolet Corvette 2008

List of elements for Satellite Radio Wiring Diagram for Chevrolet Corvette 2008:

• (coupe: behind left rear driver seat, in left rear compt) (convertible: between driver & passenger seat, mounted on bracket, below tonneau)
• Antenna sig
• Aud common
• Audio common
• Battery
• Body control module (bcm) (mounted on toe board, in right footwell)
• Coax
• Computer data lines system
• Digital radio receiver
• Drain
• Driver outside rearview mirror
• G104 (on right frame rail, below battery tray)
• Ground
• Hot at all times
• J217
• J300
• Lt aud sig
• Nca
• Passenger outside rearview mirror
• Radio
• Rdo/s- band/vics fuse 15a
• Rt aud sig
• Serial data
• X3 a6

SHIFT INTERLOCK

Shift Interlock Wiring Diagram for Chevrolet Corvette 2008

List of elements for Shift Interlock Wiring Diagram for Chevrolet Corvette 2008:

• 5 volt reference
• A/t shift lock control solenoid
• Automatic transmission shift lever
• Body control module (bcm) (mounted on toe board, in right footwell)
• Brake pedal position sensor
• Brake pedal position sensor (mounted on brake pedal bracket)
• Btsi sol/str whl lck fuse 10a
• Class 2 serial data
• Computer data lines system
• Hot at all times
• L x1
• Logic
• Low reference
• Park switch
• Pnk
• Power distribution system
• Remote control door lock receiver (rcdlr) (right side of dash)
• Tan

STARTING/CHARGING

Charging Wiring Diagram for Chevrolet Corvette 2008

List of elements for Charging Wiring Diagram for Chevrolet Corvette 2008:

• (not used) a
• Battery
• Battery positive voltage
• Body control module (bcm) (mounted on toe board, in right footwell)
• Charging gauge
• Class 2 (bcm)
• Class 2 serial data
• Clstr/hud fuse 15a
• Computer
• Coupe/ convertible
• D10
• Data lines
• Engine control module (ecm) (behind right front fender, between wheelhouse & dash panel)
• G104 (on right frame rail, below battery tray)
• G106 (on right rear side of engine, above starter solenoid)
• G201 (at base of left "a" pillar)
• G303 (right "b" pillar)
• Generator
• Generator field duty cycle signal
• Generator turn on signal
• Ground
• Hi speed gmlan serial data +
• Hi speed gmlan serial data -
• Hi speed gmlan serial data bus +
• Hi speed gmlan serial data bus -
• Horn/ alt sense fuse 2 15a
• Hot at all times
• Ign
• Instrument panel cluster
• J303
• Jx205 (in i/p harness, left of steering column)
• Jx208 (in i/p harness, left of audio amplifier)
• Logic
• Message center
• Power distribution system
• Red
• Starter motor
• System
• Tan
• Underhood fuse block (on right side of engine compt)
• Z06 model

Starting Wiring Diagram for Chevrolet Corvette 2008

List of elements for Starting Wiring Diagram for Chevrolet Corvette 2008:

• (not used)
• A/t
• A13
• A14
• Automatic transmission
• Battery
• Bcm class 2 serial data
• Body control module (bcm) (mounted on toe board, in right footwell)
• C10
• C13
• C14
• Charging circuit
• Computer data lines system
• Crank relay
• Driver information center (dic)
• E12
• Engine control module (ecm) (behind right front fender, between wheelhouse & dash panel)
• F12
• G102 (on top of right frame rail, ground for sp102)
• G104 (on right frame rail, below battery tray)
• G106 (on right rear side of engine, above starter solenoid)
• Gnd
• Hi speed gmlan serial data bus +
• Hi speed gmlan serial data bus -
• High speed gmlan serial data +
• High speed gmlan serial data -
• Ignition mode switch
• Ignition mode switch mode control
• Ignition mode switch mode voltage
• Instrument panel cluster (ipc)
• Ipc class 2 serial data
• J102
• J106
• Logic
• Off
• Park/ neutral sig
• Park/neutral sig
• Red
• Start
• Starter
• Starter enable relay control
• Starter fuse 30 40a
• Tan
• Transmission control module (tcm)
• Underhood fuse block (on right side of engine compt)
• X400

SUPPLEMENTAL RESTRAINTS

Supplemental Restraints Wiring Diagram (1 of 2) for Chevrolet Corvette 2008

List of elements for Supplemental Restraints Wiring Diagram (1 of 2) for Chevrolet Corvette 2008:

• (at base of right "a" pillar)
• Air bag ind
• Body control module (bcm) (mounted on toe board, in right footwell)
• C10
• Case ground
• Class 2 serial data
• Data link connector (dlc) (under dash, below steering column)
• Drvr seat belt sw sig
• G202
• Hot w/ run crank relay energized
• Ign
• Inflatable restraint ip module (at right side of dash)
• Inflatable restraint sensing & diagnostic module (sdm) (behind center of dash, under hvac control head)
• Inflatable restraint steering wheel module (center of steering wheel)
• Inflatable restraint steering wheel module coil (center of steering column)
• Instrument panel cluster (ipc)
• Jx205 (in i/p harness, left of steering column)
• L front end sens sig
• L pretensioner high
• L pretensioner low
• L seat position sw
• L side impact mod high
• L side impact mod low
• Left seat belt pretensioner (part of driver seat belt buckle)
• Lf side impact sig
• Logic
• Low ref
• Nca
• Pass i/p stage 1 high
• Pass i/p stage 1 low
• Pass i/p stage 2 high
• Pass i/p stage 2 low
• Pass seat belt sw sig
• Pnk
• R front end sens sig
• R pretensioner high
• R pretensioner low
• R seat position sw
• R side impact mod high
• R side impact mod low
• Rf side impact sig
• Right seat belt pretensioner (part of passenger seat belt buckle)
• Sdm class2 serial data
• Sdm/aos switch air bag fuse 10a
• Seat belt ind
• Sens sig (1)
• Sens sig (2)
• Serial data
• Shorting bar
• Signal ground
• Stage 1
• Stage 2
• Steer whl stage 1 high
• Steer whl stage 1 low
• Steer whl stage 2 high
• Steer whl stage 2 low
• Tan

Supplemental Restraints Wiring Diagram (2 of 2) for Chevrolet Corvette 2008

List of elements for Supplemental Restraints Wiring Diagram (2 of 2) for Chevrolet Corvette 2008:

• (at base of right "a" pillar)
• (under passenger seat) inflatable restraint front passenger presence system module
• Air bag off ind
• Air bag on ind
• Driver inflatable restraint seat position sensor
• Driver seat belt switch (in driver's seat belt buckle assembly)
• G202
• Gnd
• Ign
• Ind ctrl
• Inflatable restraint front passenger presence system (pps) sensor (inside passenger seat cushion)
• Inside rear view mirror
• J221 (i/p harness, 8 cm from data link connector breakout)
• J391 (driver seat harness, 10 cm from seat belt switch)
• J392
• Left inflatable restraint front end sensor (left front of engine compt, behind front fascia support)
• Left inflatable restraint side impact module (in driver seat back, toward door)
• Left inflatable restraint side impact sensor (if equipped) (inside driver door)
• Logic
• Low ref
• Nca
• Passenger inflatable restraint seat belt tension sensor
• Passenger inflatable restraint seat position sensor
• Passenger seat belt switch (in passenger's seat belt buckle assembly)
• Pnk
• Right inflatable restraint front end sensor (right front of engine compt, behind front fascia support)
• Right inflatable restraint side impact module (in passenger seat back, toward the door)
• Right inflatable restraint side impact sensor (if equipped) (inside passenger door)
• Sens sig
• Serial data
• Shorting bar
• Tan
• Volt ref

TRANSMISSION

Transmission Wiring Diagram for Chevrolet Corvette 2008

List of elements for Transmission Wiring Diagram for Chevrolet Corvette 2008:

• Accessory volt
• Accy volt sig
• Automatic transmission
• Automatic transmission input shaft spped (iss) sensor
• Automatic transmission internal mode switch (ims)
• Battery
• Battery pos volt
• Battery positive volt
• Body control module (mounted on toe board, in right footwell)
• Cluster/ hud fuse 15a
• Computer data lines system
• Cruise switch fuse 2a
• D10
• D11
• Data
• Data bus +
• Data bus -
• Driver information center (dic)
• Ecm/tcm/ easy key fuse 11 15a
• Engine control module (ecm) (behind right front fender, between wheelhouse & dash panel)
• Engine controls system
• F11
• G106 (on right rear side of engine, above starter solenoid)
• G201 (at base of left "a" pillar)
• Ground
• Hot at all times
• Hot in on or start
• Ignition 1
• In speed sensor sig
• Inflatable restraint steering wheel module coil (center of steering column)
• Instrument panel cluster
• Iss signal
• J106
• J303
• Left automatic transmission manual shift switch
• Logic
• Navigation & sound systems
• Nca
• Oss signal
• Out speed sensor sig
• Park/neutral sig
• Pnk
• Power distribution system
• Range signal a
• Range signal b
• Range signal c
• Range signal p
• Red
• Right automatic transmission manual shift switch
• Selector sig
• Serial data bus +
• Serial data bus -
• Stop lamp sig
• Stop lamp sw sig
• Tan
• Tcm/trans fuse 1 10a
• Transmission control module (tcm)
• Underhood fuse block (on right side of engine compt)
• X276
• X277

TRUNK, TAILGATE, FUEL DOOR

Trunk & Fuel Door Release Wiring Diagram, Convertible for Chevrolet Corvette 2008

List of elements for Trunk & Fuel Door Release Wiring Diagram, Convertible for Chevrolet Corvette 2008:

• Batt 1 fuse 33 60a
• Body control module (bcm) (mounted on toe board, in right footwell)
• Class 2 ser data
• Computer data lines system
• Driver information center (dic)
• Exterior rear compartment lid release switch
• Fuel door release actuator (on left side of cargo compt, behind fuel filler door)
• Fuel door release switch
• Fuel dr relse relay
• G201 (at base of left "a" pillar)
• G301 (at left "b" pillar, behind trim panel)
• G302 (at right "b" pillar, behind trim panel)
• Hot at all times
• I/p fuse block (in right front footwell, mounted to toe board)
• I/p relay block (in right front footwell, mounted to toe board)
• Instrument panel cluster (ipc)
• Interior lights system
• Interior rear compartment lid release switch
• J200
• J222
• J234
• J301
• J303
• J931
• Logic
• Pnk
• Prw/wndws trunk/fuel relse circuit breaker 30a
• Rear compartment lid latch
• Rear compartment lid lock cylinder key switch
• Remote control door lock receiver (rcdlr) (right side of dash)
• Rfa class 2 ser data
• Tan
• Trnk ajar sw sig
• Trnk key sw sig
• Trnk rel rly ctrl
• Trnk rel sw sig
• Trunk rel sw sig
• Trunk release relay
• Trunk relse fuse 15a
• Underhood fuse block (on right side of engine compt)

Trunk & Fuel Door Release Wiring Diagram, Coupe for Chevrolet Corvette 2008

List of elements for Trunk & Fuel Door Release Wiring Diagram, Coupe for Chevrolet Corvette 2008:

• Batt + voltage
• Batt 1 fuse 33 60a
• Body control module (bcm) (mounted on toe board, in right footwell)
• Cargo lmp sw sig
• Class 2 ser data
• Computer data lines system
• Driver information center (dic)
• Exterior rear compartment lid release switch
• Fuel door release actuator (on left side of cargo compt, behind fuel filler door)
• Fuel door release switch
• Fuel dr relse relay
• G201 (at base of left "a" pillar)
• G301 (at left "b" pillar, behind trim panel)
• G302 (at right "b" pillar, behind trim panel)
• Ground
• Hot at all times
• I/p fuse block (in right front footwell, mounted to toe board)
• I/p relay block (in right front footwell, mounted to toe board)
• Instrument panel cluster (ipc)
• Interior lights system
• Interior rear compartment lid release switch
• J200
• J222
• J234
• J301
• J303
• J931
• Logic
• Pnk
• Prw/wndws trunk/fuel relse circuit breaker 30a
• Rear compartment lid pull down actuator
• Remote control door lock receiver (rcdlr) (right side of dash)
• Rfa class 2 ser data
• Tan
• Trnk ajar sw sig
• Trnk key sw sig
• Trnk rel rly ctrl
• Trnk rel sw sig
• Trunk rel sw sig
• Trunk relse fuse 15a
• Underhood fuse block (on right side of engine compt)

WARNING SYSTEMS

Warning Systems Wiring Diagram for Chevrolet Corvette 2008

List of elements for Warning Systems Wiring Diagram for Chevrolet Corvette 2008:

• (i/p harness, 8 cm from data link connector breakout) pnk j221
• Ajar
• Auto
• Body control module (bcm) (mounted on toe board, in right footwell)
• Brake fluid level switch (in master cylinder reservoir)
• Brake ind
• Brk fluid lvl sens sig
• Class 2 (sdm)
• Class 2 serial data
• Closed
• Computer data lines system
• Driver door latch (in rear of driver door)
• Driver information center (dic)
• Driver seat belt switch (in driver's seat belt buckle assembly)
• Ecm high spd gmlan serial data bus +
• Ecm high spd gmlan serial data bus -
• Engine control module (ecm) (behind right front fender, between wheelhouse & dash panel)
• G101 (on left frame rail)
• G201 (at base of left "a" pillar)
• G301 (at left "b" pillar, behind trim panel)
• Gmlan (ebcm)
• Head
• High spd gmlan serial data bus +
• High spd gmlan serial data bus -
• Ign
• Inflatable restraint sensing & diagnostic module (sdm) (below center of dash, under hvac control head)
• Instrument panel cluster (ipc)
• Internal antenna
• Ipc
• Ipc class 2 serial data
• J101
• J275
• J301
• J391 (driver seat harness, 10 cm from pnk seat belt switch) b
• Left
• Left seat belt sw
• Left turn ind
• Lf dr open sw sig
• Lf turn sig sw
• Logic
• Low ref
• Low tire pressure ind
• Nca
• Off
• Open
• Park
• Park brake switch (lower front of park brake handle)
• Park brk sw sig
• Pk lmp sw on sig
• Pnk
• Radio
• Radio class 2 serial data
• Remote control door lock receiver (rcdlr) (right side of dash)
• Rf turn sig sw
• Rfa class 2 serial data
• Right
• Right turn ind
• Seat belt ind
• Tan
• Traction off ind
• Turn signal/ multi-function switch
• Underhood fuse block (on right side of engine compt) x1

WIPER/WASHER

Wiper/Washer Wiring Diagram (1 of 2) for Chevrolet Corvette 2008

List of elements for Wiper/Washer Wiring Diagram (1 of 2) for Chevrolet Corvette 2008:

• (not used)
• Accessory voltage signal
• Body control module (mounted on toe board, in right footwell)
• Diode 1
• Diode 2
• F16
• F19
• G102 (on top of right frame rail, ground for sp102)
• G16
• G19
• G201 (at base of left "a" pillar)
• G202 (at base of right "a' pillar)
• Gnd
• High
• Hot at all times
• Htd seat/ wpr rly fuse 10a
• I/p fuse block (in right front footwell, mounted to toe board)
• J102
• J216
• K10
• K11
• K14
• K15
• K18
• K19
• L10
• L18
• Logic
• Low
• M10
• M11
• M14
• M15
• M18
• M19
• Navigation system
• Park switch
• Pnk
• Run/ crank relay
• Run/ crank relay control
• To w/s wash relay 36 (diagram 2 of 2)
• Under- hood fuse block (on right side of engine compt)
• Windshield wiper motor (on left side of firewall)
• Wiper diode
• Wiper fuse 4 30a
• Wiper hi/lo relay 41
• Wiper on/off relay 45
• Wiper run/acc relay 42
• Wpr dwell fuse 10a
• Wpr/ washer fuse 10a
• X3 c3
• X3 d1
• X3 e11

Wiper/Washer Wiring Diagram (2 of 2) for Chevrolet Corvette 2008

List of elements for Wiper/Washer Wiring Diagram (2 of 2) for Chevrolet Corvette 2008:

• Body control module (mounted on toe board, in right footwell)
• Delay switch
• From wiper hi/lo relay (diagram 1 of 2)
• G101 (on left frame rail)
• G102 (on top of right frame rail, ground for sp102)
• Hdlp wash fuse 18 20a
• Hdlp wash relay 46
• Headlamp washer fluid pump (w/ washer headlamp) (rear of left wheel well, mounted in bottom of washer reservoir)
• Headlamp washer relay control
• High
• Hot at all times
• Instrument cluster panel
• Int
• J101
• Logic
• Low
• Mist
• Off
• Pnk
• Under- hood fuse block (on right side of engine compt)
• W/ washer headlamp
• W/s wash fuse 17 15a
• W/s wash relay 36
• Washer switch
• Windshield washer fluid level switch (at bottom of washer fluid reservoir)
• Windshield washer fluid pump (on left rear of engine compt, in washer fluid reservoir)
• Windshield washer relay control
• Windshield washer switch signal
• Windshield wiper switch low signal
• Windshield wiper switch signal 2
• Windshield wiper/washer switch
• Wiper motor park switch signal
• Wiper switch
• X3 c12
• X3 f2 pnk
• X4 b1 pnk