DescriptionThe engine radiator and air conditioner condenser cooling system consists of one fan operated at two different speeds:the first speed is activated at a first coolant temperature level or at a certain air conditioner coolant pressure.The second speed cuts in at a higher temperature or pressure threshold.The fan is operated by two specific relays located in the engine compartment unit. The fan supply line is protected by two specific fuses, located in the engine compartment unit.
Functional description The relays T6 and T7 in the engine compartment unit B1 manage the switching on of the fan N11 at two speeds: their coils are supplied by the ignition-controlled line (15/54), while the power lines are protected by the fuses F6 and F7, of the engine compartment unit B1 . Both are energized by a control signal - earth - coming from the engine control unit M10, pins 14 and 30 of connector A, respectively. If the engine coolant reaches a first temperature level, or the linear sensor K120 indicates to the control unit M10 - pin 54 of connector B - that a certain pressure level has been reached, the control unit M10 sends a signal - from pin 14 of connector A which energizes the fan 1st speed relay T6, which then sends the supply to the fan N11 via the additional resistor O10: the fan thus turns at the first speed (slow). Linear sensor K120 receives a power supply and reference earth from the engine management control unit M10 , pins 53 and 5 of connector A. If the coolant reaches a higher temperature level, or the linear sensor K120 indicates to the control unit M10 that a higher pressure has been reached, the control unit M10 sends a signal - from pin 30 of connector A - to the fan 2nd speed relay T7, which sends the supply directly to the fan N11: the fan then turns at the maximum speed.
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid and disconnectthe battery.1. Undo the nut.2. Move aside the retainer.3. Remove the battery carefully.2050795
5530B22
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212400577-5530B10battery - r+r2400580-5530B52Battery DRIP TRAY/SUPPORT - R.R.Open the bonnet lid.1. Disconnect the electrical connection (1a) from the negative batteryterminal (1b).2. Disconnect the electrical connection from the bodyshell3. Disconnect the electrical connection from the gearbox casing.4. Keep the battery earth lead.2050796
5530B36
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Place the vehicle on a lift.Raise the car.1. Undo the nut (1a) and disconnect the electrical connections (1b,1c) from the starter motor.2050797
5530B52
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212400577-5530B10battery - r+r1. Open the retaining bands and release the wiring.2. Remove the battery support tray (2a), releasing the dischargepipe (2b) from the passage hole (2c). 3. Undo the bolts.4. Remove the battery cage.2050799
5530B60
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Undo the nut.2. Undo the retaining buttons using the special tool3. Remove the belt.2050800
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b).2050746
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212400802-7040A37fuse box cover - r r1. Disconnect the electrical connections (1a, 1b, 1c, 1d, 1e, 1f).2. Undo the bracket retaining bolt.3. Slightly move the bracket (3a) for the dashboard trim and undothe bolt (3b).4. Undo the other bolts securing the body computer/junction unit.5. Slightly move the body computer/junction unit assembly.6. Disconnect the electrical connections (6a, 6b, 6c).7. Recover the body computer/junction unit.2050752
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect electronic control unit electrical connections (1a),(1b), (1c).2. Undo the bolts.3. Recover the control unit.2050753
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect electronic control unit electrical connections (1a),(1b), (1c).2. Undo the bolts.3. Recover the control unit.2050754
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). Proceed with removal 2400123-1048A32sleeve from air cleanerto intake manifold - r + r1. Disconnect the electrical connection from the throtle body integratedwith the M.D.S.2. Undo the bolts (2a) and move the mounting bracket (2b) aside,complete with injection-ignition system control unit (2c). 3. Undo the remaining bolt (3a) and remove throttle body with integralMDS (3b) 2049708
1056B50
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). Proceed with removal 2400123-1048A32sleeve from air cleanerto intake manifold - r + r1. Disconnect the electrical connection from the engine coolanttemperature sensor.2. Undo and remove the engine coolant temperature sensor.2049709
1056B51
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). Proceed with removal 2400120-1048A10air cleaner filtering element- replace1. Disconnect the electrical connection from the cam angle sensor. 2. Undo the bolt (2a) and remove the cam angle sensor (2b). 2049710
1056B54
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). 1. Disconnect the electrical connection from the intake air temperature/pressuresensor.2. Undo the bolts (2a) and remove the intake air temperature/pressuresensor (2b).2049711
1056B60
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). Proceed with removal 2400120-1048A10air cleaner filtering element- replace1. Undo the fuel manifold pipe protective plug (1a) and use tool(1b) to drain fuel system pressure. 23Recover the fuel which comes outin a suitable container. 2. Disconnect the rapid attachment for the fuel supply pipe fromthe fuel manifold pipe.3. Disconnect the electrical connections from the injectors.Release the injector electrical wiringfrom the fixings and move it aside. 2049712
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Remove the safety clip.2. Remove the injector.2049714
1056B78
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). 1. Disconnect the electrical connection from the switch on the clutchpedal. 2. Rotate and remove the switch on the clutch pedal.2049715
1056B82
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). 1. Disconnect the electrical connections (1a) and (1b) from theinjection/ignition system control unit. 2. Undo nut (2a) and disconnect earth lead (2b) from the injection-ignitionsystem control unit. 3. Undo the remaining nuts (3a) and remove injection/ignition controlunit (3b) from the bracket. 2049716
1056B87
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). Proceed with removal 2400134-1056B82injection/ignition systeme.c.u. (one) - r + r1. Undo the bolts (1a) and remove the injection/ignition controlunit mounting (1b).2049717
1056B90
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on the ramp Proceed with removal 2400577-5530B10battery - r+r Proceed with removal 2400580-5530B52Battery DRIP TRAY/SUPPORT- R.R. Proceed with removal 2400120-1048A10air cleaner filtering element- replace1. Loosen the band and disconnect the engine oil vapour intake pipeand the side of the sleeve from the air cleaner to the intake manifold2. Loosen the band, disconnect the hose from the air filter to theintake manifold, intake manifold side and remove it.2049718
pressure pump electric control
1060G10
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). 1. Disconnect the electrical connection from the air flow meter. 2. Loosen the band and disconnect the the turbocharger air inletsleeve from the rigid pipe, air flow meter side.3. Undo the bolts (3a) and remove the air flow meter (3b).2050095
1060G14
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on the ramp Proceed with removal 1. Loosen the band and disconnect the lower radiator coolant outlethose from the radiator, radiator side.23Collect the engine coolant ina suitable container.2050096
1060G16
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). 1. Disconnect the electrical connection from the air flow meter. 2. Loosen the band and disconnect the the turbocharger air inletsleeve from the rigid pipe, air flow meter side.2050099
1060G20
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). 1. Disconnect the electrical connection for the rpm sensor.2. Undo the bolt (2a) and remove the engine rpm sensor (2b). 2050102
1060G22
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on the rampEnsure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). 1. Disconnect the electrical connection from the air flow meter. 2. Loosen the band and disconnect the the turbocharger air inletsleeve from the rigid pipe, air flow meter side.2050104
1060G28
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). 1. Disconnect the electrical connection from the air flow meter. 2. Loosen the band and disconnect the the turbocharger air inletsleeve from the rigid pipe, air flow meter side.2050107
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). 1. Disconnect the electrical connection from the air flow meter. 2. Loosen the band and disconnect the the turbocharger air inletsleeve from the rigid pipe, air flow meter side.2050115
1060G90
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on the ramp Proceed with removal 2400577-5530B10battery - r+r Proceed with removal 2400580-5530B52Battery DRIP TRAY/SUPPORT- R.R.1. Disconnect the electrical connection from the air flow meter. 2. Loosen the band and disconnect the the turbocharger air inletsleeve from the rigid pipe, air flow meter side.2050119
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on the rampEnsure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). Proceed with removal 2400120-1048A10air cleaner filtering element- replace Proceed with removal 2400972-7210E10R.R. FRONT BUMPER1. Disconnect the electrical connections from the engine coolingfan resistor.2. Disconnect the electrical connection for the radiator coolingfan and move the electrical wiring to the side.2049796
1088E20
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). 1. Disconnect the electrical connection from the air flow meter. 2. Loosen the band and disconnect the the turbocharger air inletsleeve from the rigid pipe, air flow meter side.2050242
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Čeština
Dansk
Deutsch
Ελληνικά
English
English
Suomi
Français
Français
עברית
Hrvatski
Magyar
Italiano
日本語
한국어
Nederlands
Polski
Português
Português
Română
Русский
Slovenčina
Slovenščina
Svenska
Türkçe
中文 (中国)
