All Wiring Diagrams for Jeep Grand Cherokee Laredo X 2013 model

AIR CONDITIONING

Automatic A/C Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for Automatic A/C Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013:

• (left side of engine compt) integrated power module
• (not used)
• 3.6l
• A/c clutch coil
• A/c clutch fd
• A/c heater control
• A417
• A924
• Abmt temp/ fcm ssr rtn 1
• Ac press sens fd
• Ac press sens rtn
• Ac press sig
• Act com
• Act com 2
• Act temp (driv)
• Auto hdlp sig
• Batt feed
• Blower motor relay
• Bus bar
• C121
• C13
• C139
• C18
• C200
• C202
• C21
• C32
• C33
• C34
• C35
• C56
• C61
• C807
• C818
• C918
• Can c (+)
• Can c (-)
• Can ihs (+)
• Can ihs (-)
• Circuit board
• Coil sig
• Computer data lines system
• D264
• D265
• D64
• D65
• Evap sig
• Evap snse rtn
• Except 3.6l
• F921
• Ft blw pwm ctrl
• Ft mode act drv
• Fuse 100a
• Fuse block
• Fuse j15 40a
• Fuse j19 60a
• Fuse m11 10a
• Fuse m15 20a
• Fuse m34 10a
• G139
• G31
• G39
• G906a (right front of engine compt)
• G912a (under front of center console)
• G931
• G939
• Gnd
• Hot at all times
• Hot w/ run relay energized
• Hot w/ run/ start relay energized
• Ign r
• Iod fd
• K175
• L24
• Nca
• Pass temp dr act
• Power distribution system
• Rad fan low spd sig
• Rad fan rly
• Rad fan rly col sig
• Radiator cooling fan module (behind radiator)
• Radiator fan low relay
• Rcrc act dr
• Red
• Rr ctrl blw sw fd
• S258
• Snsr abmt temp sig
• Snsr sunld rtn
• Ssr sunld sig
• Ssr sunld sig 2
• Z906
• Z912

Automatic A/C Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for Automatic A/C Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013:

• (5.7l: top front of engine) (3.6l: rear of left cylinder bank) engine coolant temperature sensor
• (above center of radiator grille) hood ajar switch
• (behind radiator) (3.6l) radiator cooling fan module
• (left front of engine compt) a/c pressure transducer
• (left front of engine compt, in fluid reservoir) washer fluid level sensor
• (left side of front grille) ambient air temperature sensor
• (right front of engine compt) (3.6l) radiator fan high relay
• (right front of engine compt) powertrain control module
• 6.4l
• A/c clutch coil
• A/c compressor clutch
• A/c press sig
• A/c press snse rtn
• A/c press snsr fd
• Abmt/ temp fcm ssr rtn 1
• Ac clutch fd
• Act com
• Act com 2
• Act temp (drn)
• Auto hdlp sig
• Blower motor (right side of hvac unit)
• C13
• C139
• C161
• C56
• C805
• C806
• Can c (+)
• Can c (-)
• Computer data lines system
• Cool temp sens sig
• D64
• D65
• Eng ctrl com snsr rtn
• Engine controls system
• Evaporator temperature sensor (left side of hvac unit)
• Except 6.4l
• Front blower motor power module
• Front mode door actuator (left side of hvac unit)
• Ft blw fd
• Ft blw pwm ctrl
• Ft mode drv act
• G906a (right front of engine compt)
• G909a (right rear of engine compt)
• G911a (left side of dash)
• Gnd
• K900 (or k915)
• Left blend door actuator (left side of hvac unit)
• N23
• N24
• Pass temp dr act
• Pwn blw fd
• Pwn blw rtn
• Rad fan mtr fd
• Rad fan mtr fd 2
• Rcrc act dr
• Recirculation door actuator (right side of hvac unit)
• Right blend door actuator (center of hvac unit)
• S134
• S162 (6.4l) s113 (5.7l) s101 (3.6l)
• S232
• S233
• Snsr sunld rtn
• Ssr sunld sig
• Ssr sunld sig 2
• Sun sensor (center of top of dash)
• Z906
• Z911

Manual A/C Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for Manual A/C Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013:

• (left side of engine compt) integrated power module
• (not used)
• 3.6l
• A/c clutch coil
• A/c clutch fd
• A/c heater control
• A417
• A924
• Aat sig
• Ac press sens fd
• Ac press sens rtn
• Ac press sig
• Act com
• Act com 2
• Act temp (driv)
• Auto hdlp sig
• Batt feed
• Blower motor relay
• Bus bar
• C121
• C13
• C139
• C18
• C200
• C202
• C21
• C32
• C33
• C34
• C35
• C56
• C61
• C807
• C818
• C918
• Can c (+)
• Can c (-)
• Can ihs (+)
• Can ihs (-)
• Circuit board
• Coil sig
• Computer data lines system
• D264
• D265
• D64
• D65
• Evap sig
• Evap snse rtn
• Except 3.6l
• F921
• Ft blw pwm ctrl
• Ft mode act drv
• Fuse 100a
• Fuse block
• Fuse j15 40a
• Fuse j19 60a
• Fuse m11 10a
• Fuse m15 20a
• Fuse m34 10a
• G31
• G906a (right front of engine compt)
• G912a (under front of center console)
• G931
• G939
• Gnd
• Hot at all times
• Hot w/ run relay energized
• Hot w/ run/ start relay energized
• Ign r
• Iod fd
• K175
• L24
• Nca
• Pass temp dr act
• Power distribution system
• Rad fan low spd sig
• Rad fan rly
• Rad fan rly col sig
• Radiator cooling fan module (behind radiator)
• Radiator fan low relay
• Rcrc act dr
• Red
• Rr ctrl blw sw fd
• S258
• Snsr sunld rtn
• Ssr gnd
• Z906
• Z912

Manual A/C Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for Manual A/C Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013:

• (5.7l: top front of engine) (3.6l: rear of left cylinder bank) engine coolant temperature sensor
• (above center of radiator grille) hood ajar switch
• (behind radiator) (3.6l) radiator cooling fan module
• (left front of engine compt) a/c pressure transducer
• (left front of engine compt, in fluid reservoir) washer fluid level sensor
• (left side of front grille) ambient air temperature sensor
• (right front of engine compt) (3.6l) radiator fan high relay
• (right front of engine compt) powertrain control module
• 6.4l
• A/c clutch coil
• A/c compressor clutch
• A/c press sig
• A/c press snse rtn
• A/c press snsr fd
• Abmt/ temp fcm ssr rtn 1
• Ac clutch fd
• Act com
• Act com 2
• Act temp (drn)
• Auto hdlp sig
• Blower motor (right side of hvac unit)
• C13
• C139
• C161
• C56
• C805
• C806
• Can c (+)
• Can c (-)
• Computer data lines system
• Cool temp sens sig
• D64
• D65
• Eng ctrl com snsr rtn
• Engine controls system
• Evaporator temperature sensor (left side of hvac unit)
• Except 6.4l
• Front blower motor power module
• Front mode door actuator (left side of hvac unit)
• Ft blw fd
• Ft blw pwm ctrl
• Ft mode drv act
• G906a (right front of engine compt)
• G909a (right rear of engine compt)
• G911a (left side of dash)
• Gnd
• K900 (or k915)
• Left blend door actuator (left side of hvac unit)
• N23
• N24
• Pass temp dr act
• Pwn blw fd
• Pwn blw rtn
• Rad fan mtr fd
• Rad fan mtr fd 2
• Rcrc act dr
• Recirculation door actuator (right side of hvac unit)
• Right blend door actuator (center of hvac unit)
• S134
• S162 (6.4l) s113 (5.7l) s101 (3.6l)
• S232
• S233
• Snsr sunld rtn
• Sun sensor (center of top of dash)
• Z906
• Z911

ANTI-LOCK BRAKES

Anti-lock Brakes Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Anti-lock Brakes Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• (left rear of engine compt) brake fluid level sensor
• (left rear of engine compt) g901a
• (under front of center console) g912a
• 6.4l
• A107
• A111
• Anti-lock brakes module (left front of engine compt)
• B15
• B16
• B20
• B31
• B32
• B33
• Batt fd 9
• Boost vac snsr fd
• Brk actv
• Brk actv sns sig
• Brk actv sns sig c3
• Brk actv sns sig2
• Brk lvl sw sig
• Bstr vac press sig
• Bstr vac sens rtn
• C192
• C201
• C205
• C315
• C316
• Can bus (+) yaw
• Can bus (-) yaw
• Can c (+)
• Can c (-)
• Can ihs (+)
• Can ihs (-)
• Circuit board
• Cluster
• Compass module
• Computer data lines system
• D264
• D265
• D464
• D465
• D506
• D64
• D65
• Dynamics sensor (left side of dash)
• Except 6.4l
• F941
• Fd abs mod batt
• Fd abs pmp
• Fd abs/esp clstr snsr
• Fuse j06 40a
• Fuse j07 30a
• Fuse m20 15a
• Fuse m37 10a
• G901a (left rear of engine compt)
• G912a (under front of center console)
• Gnd
• Hot at all times
• Hot w/ run/ start relay energized
• Ign rs
• Left front abs wheel speed sensor (left front wheel hub assembly)
• Left rear abs wheel speed sensor
• Lin ccn
• Lt ft wheel (+)
• Lt ft wheel (-)
• Lt rr wheel (+)
• Lt rr wheel (-)
• Nca
• Parking brake switch (top of parking brake assembly)
• Powertrain control module (right front of engine compt)
• Prk brk sw sig
• Red
• Right front abs wheel speed sensor (right front wheel hub assembly)
• Right rear abs wheel speed sensor
• Rt ft wheel (+)
• Rt ft wheel (-)
• Rt rr wheel (+)
• Rt rr wheel (-)
• S231
• S237
• S352
• Sns sig2
• Stop lamp switch (on brake pedal assembly)
• Tan/ red
• Tan/red
• Totally integrated power module (left side of engine compt)
• Upper bank switch
• Vacuum pressure sensor (right rear of engine compt)
• Z907
• Z908

ANTI-THEFT

Forced Entry Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for Forced Entry Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013:

• 87a
• Abmt temp/ fcm ssr rtn 1
• Abmt temp/fcm ssr rtn 1
• Ambient air temperature sensor (left side of front grille)
• C300
• C301
• C305
• C306
• C383
• C384
• C390
• C392
• Can ihs (+)
• Can ihs (-)
• Circuit board
• Computer data lines system
• D264
• D265
• Door lock relay
• Dr ajar lt rr sig
• Dr ajar rt rr sig
• Dr lk lt ft
• Dr lk rt ft
• Dr lock rly ctrl lt
• Dr ulk rt ft
• Driver door latch
• Driver door unlock relay
• Drv ft dr ajar sw in
• Flip-up glass latch
• Flpr mtr rel
• Front washer fluid level sensor (left front of engine compt, in fluid reservoir)
• Ft drv dr lk
• Ft drv dr ulk
• Ft pass dr lk
• Ft pass dr ulk
• Fuse m38 25a
• G306
• G70
• G74
• G75
• G76
• G77
• G78
• G80
• G919a (base of right "c" pillar)
• G923a (left "d" pillar)
• G924a (right "d" pillar)
• G931
• Gnd
• Hot at all times
• Left rear door latch
• Lgate ajar sig
• Lt rr dr ajar sig
• Lt rr lk
• Lt rr ulk
• Nca
• P920
• P930
• P940
• Pass ft & rr & drv rr ulk
• Pass ft dr ajar sw in
• Passenger door latch
• Passenger door unlock relay
• Q81
• Right rear door latch
• Rr glass ajar sig
• Rr glss ajar sig
• Rt rr dr ajar sig
• Rt rr lk
• Rt rr ulk
• S134
• S335
• S501
• S600
• S700
• S800
• Totally integrated power module (left side of engine compt)
• Uhood sw sig

Forced Entry Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for Forced Entry Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013:

• (not used) c316
• 100 fd to dr node-drv
• A214
• A215
• Abmt temp/ fcm ssr rtn 1
• Batt fd
• C300
• C301
• C306
• C383
• C384
• C392
• Can ihs (+)
• Can ihs (-)
• Can ihs +
• Can ihs -
• Computer data lines system
• D264
• D265
• D501
• D903
• Driver door module
• Driver window/ door lock switch
• E34
• Eatx batt fd
• Ft pass dr lk sw sig
• Ft pass sw illm/sns rtn
• Ft pass up sw snse
• Fuse j4 25a
• Fuse j5 25a
• Fuse m26 10a
• Fuse m3 20a
• G160
• G78
• G909a (right rear of engine compt)
• G923a (left "d" pillar)
• Gnd
• Hood ajar switch (above center of radiator grille)
• Hot at all times
• Iod fd to dr node-drv
• L177
• Left rear power window switch
• Lgate ajar sig
• Liftgate door latch
• Liftgate unlock relay
• Lin dcm dr
• Lin slve rtn
• Nca
• Park lamp relay
• Passenger door module
• Passenger window/ door lock switch
• Power distribution center (left side of engine compt)
• Power liftgate module (left "d" pillar)
• Prk lmp rly ctrl
• Q336
• Q936
• Right rear power window switch
• Rr dr ulk rly ctrl
• S302
• S355
• S501
• Sw illm ft pass
• Sw pwr lk out fd rr lt
• Sw pwr lk out fd rr tt
• Totally integrated power module (left side of engine compt)
• Uhood sw sig

Passive Anti-theft Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Passive Anti-theft Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• A106
• Ant pem1 rtn
• Ant pem1 sig
• Ant pem2 rtn
• Ant pem2 sig
• Ant pem3 rtn
• Ant pem3 sig
• Ant pem4 rtn
• Ant pem4 sig
• Bus (+) can ihs
• Bus (-) can ihs
• C201
• C202
• C300
• C303
• C305
• C308
• C383
• C384
• C390
• C392
• Can c (+)
• Can c (-)
• Computer data lines system
• D264
• D265
• D51
• D52
• D920
• D921
• D922
• D923
• D924
• D925
• D926
• D927
• Ext dr hndl sw rtn drv
• Ext dr hndl sw rtn pass
• Ext dr hndl sw sig drv
• Ext dr hndl sw sig pass
• Ext lgate hndl sw rtn
• Ext lgate hndl sw sig
• Fuse m27 10a
• G912a (under front of center console)
• Gnd
• Hot at all times
• Ign sw fd
• Left front exterior door handle switch
• License plate lamp/ rear camera assembly
• Nca
• P124
• P125
• P30
• P39
• P400
• P401
• Passive entry antenna 1 (left rear door)
• Passive entry antenna 2 (right rear door)
• Passive entry antenna 3 (center of dash)
• Passive entry antenna 4 (center of rear fascia)
• Passive entry module (right side of dash)
• Right front exterior door handle switch
• S230
• Totally integrated power module (left side of engine compt)
• Z912

BODY CONTROL MODULES

Body Control Modules Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for Body Control Modules Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013:

• 110v ac pwr anable sw sig
• A106
• A108
• A16
• A206
• A207
• A214
• A215
• A27
• A412
• A904
• A906
• A907
• A909
• A925
• Air conditioning system
• Anti-lock brakes system
• B20
• Batt drct to pdc
• Batt fd 4
• Batt fd 6
• Batt fd 7
• Batt fd 9
• Brk lvl sw sig
• Can bus diag (+)
• Can bus diag (-)
• Can c (+)
• Can c (-)
• Can ihs (+)
• Can ihs (-)
• Cgr lgtr batt fd
• Clstr/chmsl batt fd
• Computer data lines system
• Cooling fans system
• D264
• D265
• D51
• D52
• D71
• D72
• Door locks & anti-theft systems
• Door locks system
• Dr ajar lt rr sig
• Dr ajar rt rr sig
• Driv ft dr ajar sw in
• Elec brk conn
• Engine controls system
• Exterior lights system
• F100
• F20
• F201
• F30
• F306
• F307
• F71
• F921
• F930
• F931
• F981
• Flpr glss rel
• Flpr mtr rel
• Fog lmp/ind fd2
• Ft blw fd
• Ft drv dr lk
• Ft drv dr ulk
• Ft pass dr lk
• Ft wpr mtr prk sig
• Ft wsh mtr ctrl
• Fuel lvl snsr rtn
• Fuel sndr lvl sig
• Fuse 5 150a
• Fuse block
• G109
• G31
• G70
• G74
• G75
• G76
• G77
• G78
• G80
• G931
• Hdlp lt rtn
• Hdlp rt rtn
• Headlights & exterior lights systems
• Headlights & exterior lights systems engine controls system
• Headlights system
• Hood sw sig
• Horn drv
• Horn drv 2
• Horns system
• Hot at all times
• Hzrd sw sig
• Ign r
• Ign run
• Ign run acc
• Ign run/st
• Ign sw fd
• Instrument cluster system
• Iod fd
• Iod fd to dr node-drv
• Iod fd to dr node-pass
• K175
• L160
• L161
• L33
• L34
• L43
• L44
• L51
• L62
• L63
• L673
• L674
• L777
• L78
• L90
• L91
• L910
• L911
• Lgate ajar sig
• Lo wsh sw snse
• Lt ft prk/tl lmps 2
• Lt hi beam fd
• Lt lo beam fd
• Lt rr lk
• Lt rr trn sig fd
• Lt trn sig ind
• Mod fsed batt fd
• Mtr rr wpr prk sig
• N23
• Navigation system
• Orc mod run/strt ign
• P32
• P38
• P807
• P910
• P920
• P930
• Pass ft dr ajar sw in
• Pnk/tan
• Power distribution system
• Power tops & wiper/washer systems
• Power tops system
• Power windows system
• Q80
• Rad fan mtr fd
• Rad fan rly coil sig
• Rad fan rly sw sig
• Radio outlets ign fd
• Red
• Rr 12v recpt ign fd
• Rr glss ajar sig
• Rr wsh ctrl
• Rt ft prk/tl lmps 1
• Rt hi beam fd
• Rt lo beam fd
• Rt rr lk
• Rt rr trn sig fd
• Rt trn sig ind
• Seats & memory systems
• Seats system
• Snsr abmt temp sig
• Snsr abmt temp/fcmssr rtn
• Starting/charging & exterior lights systems
• Stp lmp sig
• Tan/red
• Totally integrated power module (left side of engine compt)
• Trlr-lt
• Trlr-rt
• Ttow ign fd
• W10
• W17
• W20
• Warning & trunk, tailgate, fuel doors systems
• Wdw run/accy ign
• Wiper/washer system
• X21
• X22

Body Control Modules Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for Body Control Modules Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013:

• (base of right "c" pillar) g919a
• A/c clutch coil
• A/c clutch fd
• A/c press sig
• A/c press snse rtn
• A104
• A107
• A111
• A115
• A116
• A144
• A209
• A408
• A413
• A417
• A855
• A905
• A959
• Abs mod batt fd
• Abs pmp fd
• Ac press snsr fd
• Air conditioning & engine controls systems
• Air conditioning system
• Anti-lock brakes system
• Asd ctrl fd 1
• Asd ctrl fd 3
• Asd rly fd
• Asd rtn
• Batt fd
• Batt fd 5
• Bkup lmps fd
• C13
• C15
• C18
• C818
• C918
• Can c (+)
• Can c (-)
• Computer data lines system
• Cooling fans system
• D64
• D65
• Defogger system
• Door locks system
• Drl sig
• Elec bklt fd
• Eng ctrl drct batt fd
• Eng ctrl fuel pmp rly sig
• Eng ctrl run/strt ign
• Engine controls & transmissions systems
• Engine controls & transmissions systems air conditioning system
• Engine controls system
• Exterior lights & anti-lock brakes systems
• Exterior lights & mirrors systems
• Exterior lights system
• F202
• F342
• F344
• F941
• F942
• F943
• Ft pass dr ulk
• Ft wpr mtr hi spd fd
• Ft wpr mtr lo spd fd
• Fuel pump mtr fd
• G909a (right rear of engine compt)
• G919a (base of right "c" pillar)
• Gnd
• Headlights system
• Ign rs
• Ign ulk/run/strt
• Iod fd
• K31
• K51
• L177
• L56
• L57
• L60
• L678
• L77
• Lt dr ulk
• Lt ft prk/tl lmps 1
• P34
• P940
• Power distribution system
• Power windows system
• Prk lmp rly ctrl
• Pwr lgate mod batt fd
• Rad fan hi spd sig
• Red
• Rr wpr mtr sig
• Rt ft trn sig fd
• Rt rr ulk
• Sound & interior lights systems
• Sound systems
• Starting/charging system
• Stp lmp sig
• Strtr coil mtr fd
• Strtr ovrde rly coil rtn
• Sw batt fd
• T15
• T16
• T750
• T752
• Tan/red
• Totally integrated power module (left side of engine compt)
• Transmissions system
• Ttow prk lmp sig
• W13
• Wiper/washer system
• Z909
• Z919

COMPUTER DATA LINES

Computer Data Lines Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for Computer Data Lines Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013:

• (+) can c
• (+) can ihs
• (-) can ihs
• (3.6l) s167
• (5.7l & 3.6l)
• (under left side of dash) data link connector
• 6.4l
• A/c-heater control module
• A408
• Adaptive cruise control module (center of front fascia)
• Blind spot module (under driver's seat)
• C1 (6.4l)
• C139
• C161
• C201
• C202
• C204
• C205
• C267
• C300
• C306
• C320
• C321
• C663
• C665
• Can (+)
• Can (-)
• Can 2 (+)
• Can 2 (-)
• Can c (+)
• Can c (-)
• Can ihs (+)
• Can ihs (-)
• Circuit board
• Compass module
• D diag (+) can bus
• D diag (-) can bus
• D264
• D265
• D506
• D51
• D52
• D64
• D65
• D71
• D72
• Driver door module
• Drivetrain control module (under driver's seat)
• Except 6.4l
• Fuse m30 15a
• G912a (under front of center console)
• Hands free module (if equipped) (left end of dash)
• Heated seat module (under front passenger seat)
• Hot at all times
• Lin ccn
• Lin tire pres
• Memory seat module (under driver seat)
• Nca
• Park assist module (right "d" pillar)
• Passenger door module
• Power liftgate module (left "d" pillar)
• Power steering pump motor (3.6l) (lower right front of engine)
• Powertrain control module (right front of engine compt)
• Radio
• Radio amplifier (left rear cargo compartment floor)
• Rain sensor (forward of interior rearview mirror)
• Right front lamp assembly
• S132
• S133
• S234
• S235
• S236
• S237
• S239
• S240
• S241
• S242
• S243
• S244
• S255
• S301
• S305
• S306
• S307
• S309
• S310
• S312
• S313
• S316
• S318 (4wd)
• S319 (4wd)
• S321 (5.7l 4wd & 6.4l)
• S356
• S358
• S359
• S386
• S387
• S900
• S901
• Totally integrated power module (left side of engine compt)
• Transfer case selector switch
• Upper bank switch
• Video screen module (in rear overhead console)
• Z912

Computer Data Lines Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for Computer Data Lines Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013:

• (left "c" pillar) tire pressure module
• Active damping control module (6.4l) (under driver seat)
• Air suspension control module (except 6.4l) (under driver seat)
• Anti-lock brakes module (left front of engine compt)
• C204
• C267
• Can (+)
• Can (-)
• Can c (+)
• Can c (-)
• Can ihs (+)
• Can ihs (-)
• Cluster
• D507
• D51
• D52
• D64
• D65
• Electronic limited slip differential module (under left side of rear seat)
• Inside rearview
• Lin ccn
• Lin sccm
• Lin tire pres
• Mirror
• Occupant restraint controller module (under center console)
• Passive entry module (right side of dash)
• S264
• S265
• S320 (5.7l 4wd & 6.4l)
• Shift lever assembly
• Speed control switch
• Steering control module (steering column)
• Transmission control module (3.6l) (left side of dash)
• Transmission control module (6.4l) (left side of dash)
• Wireless ignition node

COOLING FAN

Cooling Fan Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Cooling Fan Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• (not used)
• 3.6l
• 6.4l
• A209
• A924
• Batt fd
• C139
• Can c (+)
• Can c (-)
• Circuit board
• Coil sig
• Computer data lines system
• Cool temp sens sig
• D64
• D65
• Eng ctrl com snsr rtn
• Engine coolant temperature sensor (3.6l: rear of left cylinder bank) (except 3.6l: top front of engine)
• Except 3.6l
• Except 6.4l
• Fuse 100a
• Fuse 15a
• Fuse block
• Fuse j19 60a
• Fuse m15 20a
• G906a (right front of engine compt)
• G906a (right front of of engine compt)
• G909a
• Gnd
• Hot at all times
• Hot w/ run/ start relay energized
• K175
• K900 (or k915)
• N23
• N24
• Nca
• Power distribution system
• Powertrain control module (right front of engine compt)
• Rad fan low speed sig
• Rad fan mtr fd
• Rad fan mtr fd 2
• Rad fan rly
• Rad fan rly coil sig
• Radiator cooling fan module (3.6l) (behind radiator)
• Radiator cooling fan module (except 3.6l) (behind radiator)
• Radiator fan high relay (3.6l) (right front of engine compt)
• Radiator fan low relay
• Red
• S110 (except 6.6l)
• S162 (6.4l) s113 (5.7l) s101 (3.6l)
• Totally integrated power module (left side of engine compt)
• Z906
• Z909

CRUISE CONTROL

3.6L

3.6L, Cruise Control Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for 3.6L, Cruise Control Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013:

• (3.6l) s109 (5.7l) s125
• (right front of engine compt) g903a
• 1 snsr sig
• 5.7l
• A209
• Accel ped pos
• Accel ped pos rtn
• Accel ped pos rtn 2
• Accel ped pos sig1
• Accel ped pos snsr rtn
• Accelerator pedal position sensor (base of accelerator pedal)
• App snsr sig2
• B15
• B16
• Brake sig
• Brake sig 2
• C161
• C202
• C315
• C318
• Can c (+)
• Can c (-)
• Can ihs (+)
• Can ihs (-)
• Circuit board
• Cluster
• Computer data lines system
• D64
• D65
• Eng ctrl drct batt
• Fuel tank pressure sensor
• Fuse m1 15a
• Fuse m15 20a
• Fuse m28 15a
• Fuse m37 10a
• Gnd
• Hot at all times
• Hot w/ run/ start relay energized
• Ignition win wireless node
• Input speed sensor (left side of transmission)
• Input speed sig
• K122
• K124
• K126
• K167
• K22
• K23
• K29
• K400
• K855
• K856
• K922
• L51
• Nca
• Output speed
• Output speed sensor (left side of transmission)
• Powertrain control module (right front of engine compt)
• Prim snsr fd1
• Prim snsr fd2
• Red
• S108 (3.6l) s124 (5.7l)
• S110
• S116
• S352
• S353
• S388
• S392
• Snsr rtn 2
• Speed sens gnd
• Stp lmp sig
• T13
• T14
• T41
• T52
• Tan/red
• Throttle body (3.6l: right rear of engine) (5.7l: top of front of engine)
• Thrtl pos mtr pos
• Thrtl pos snsr rtn
• Thrtl pos snsr sig 1
• Thrtl pos snsr sig 2
• Totally integrated power module (left side of engine compt)
• Trans rng prk/ neut sig
• Transmission solenoid/ trs assembly
• Z903

3.6L, Cruise Control Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for 3.6L, Cruise Control Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013:

• (left front of engine, in multiple displacement solenoid harness) s270
• Adaptive cruise control module (center of front fascia)
• Brake sig
• Brake sig 2
• C139
• C161
• C2 input spd (n2) sig+
• Can c (+)
• Can c (-)
• Clstr/chmsl batt
• Computer data lines system
• D507
• D51
• D52
• D64
• D65
• Dimm sw
• Electrohydraulic control unit
• Evic rmux sig 1
• Evic/nav rmux rtn
• F943
• G909a (right rear of engine compt)
• G912a (under front of center console)
• G923a (left "d" pillar)
• Gnd
• Horn switch
• Hrn sw sig
• Htd str whl sig
• Ign rs
• Input spd (n2) sig+
• Input spd (n3) sig+
• Left remote radio switch
• Left steering wheel switch
• Lin sccm
• Red
• Rem rad ctrl sw sig
• Rem rad sw snse rtn
• Right remote radio switch
• S145
• S271
• S272
• Spd snsr rtn
• Speed control switch
• Steering control module (steering column)
• Steering wheel heater sensor
• Stop lamp switch (on brake pedal assembly)
• Stp lmp sig
• Sw spd ctrl rtn
• Sw spd ctrl snse 1
• Sw spd ctrl snse 2
• T13
• T70
• T71
• Tan/red
• Transmission control module (3.6l) (left side of dash)
• V71
• V72
• V937
• Z909
• Z912

5.7L

5.7L, Cruise Control Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for 5.7L, Cruise Control Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013:

• (3.6l) s109 (5.7l) s125
• (right front of engine compt) g903a
• 1 snsr sig
• 5.7l
• A209
• Accel ped pos
• Accel ped pos rtn
• Accel ped pos rtn 2
• Accel ped pos sig1
• Accel ped pos snsr rtn
• Accelerator pedal position sensor (base of accelerator pedal)
• App snsr sig2
• B15
• B16
• Brake sig
• Brake sig 2
• C161
• C202
• C315
• C318
• Can c (+)
• Can c (-)
• Can ihs (+)
• Can ihs (-)
• Circuit board
• Cluster
• Computer data lines system
• D64
• D65
• Eng ctrl drct batt
• Fuel tank pressure sensor
• Fuse m1 15a
• Fuse m15 20a
• Fuse m28 15a
• Fuse m37 10a
• Gnd
• Hot at all times
• Hot w/ run/ start relay energized
• Ignition win wireless node
• Input speed sensor (left side of transmission)
• Input speed sig
• K122
• K124
• K126
• K167
• K22
• K23
• K29
• K400
• K855
• K856
• K922
• L51
• Nca
• Output speed
• Output speed sensor (left side of transmission)
• Powertrain control module (right front of engine compt)
• Prim snsr fd1
• Prim snsr fd2
• Red
• S108 (3.6l) s124 (5.7l)
• S110
• S116
• S352
• S353
• S388
• S392
• Snsr rtn 2
• Speed sens gnd
• Stp lmp sig
• T13
• T14
• T41
• T52
• Tan/red
• Throttle body (3.6l: right rear of engine) (5.7l: top of front of engine)
• Thrtl pos mtr pos
• Thrtl pos snsr rtn
• Thrtl pos snsr sig 1
• Thrtl pos snsr sig 2
• Totally integrated power module (left side of engine compt)
• Trans rng prk/ neut sig
• Transmission solenoid/ trs assembly
• Z903

5.7L, Cruise Control Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for 5.7L, Cruise Control Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013:

• (left front of engine, in multiple displacement solenoid harness) s270
• Adaptive cruise control module (center of front fascia)
• Brake sig
• Brake sig 2
• C139
• C161
• C2 input spd (n2) sig+
• Can c (+)
• Can c (-)
• Clstr/chmsl batt
• Computer data lines system
• D507
• D51
• D52
• D64
• D65
• Dimm sw
• Electrohydraulic control unit
• Evic rmux sig 1
• Evic/nav rmux rtn
• F943
• G909a (right rear of engine compt)
• G912a (under front of center console)
• G923a (left "d" pillar)
• Gnd
• Horn switch
• Hrn sw sig
• Htd str whl sig
• Ign rs
• Input spd (n2) sig+
• Input spd (n3) sig+
• Left remote radio switch
• Left steering wheel switch
• Lin sccm
• Red
• Rem rad ctrl sw sig
• Rem rad sw snse rtn
• Right remote radio switch
• S145
• S271
• S272
• Spd snsr rtn
• Speed control switch
• Steering control module (steering column)
• Steering wheel heater sensor
• Stop lamp switch (on brake pedal assembly)
• Stp lmp sig
• Sw spd ctrl rtn
• Sw spd ctrl snse 1
• Sw spd ctrl snse 2
• T13
• T70
• T71
• Tan/red
• Transmission control module (3.6l) (left side of dash)
• V71
• V72
• V937
• Z909
• Z912

6.4L

6.4L, Cruise Control Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for 6.4L, Cruise Control Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013:

• (right rear of engine compt) g909a
• A209
• Accel ped pos sig1
• Accelerator pedal position sensor (base of accelerator pedal)
• B15
• B16
• Brake actv snse sig
• Brake actv snse sig 2
• C161
• C2 input spd (n2) sig+
• C202
• C315
• Can c (+)
• Can c (-)
• Can ihs (+)
• Can ihs (-)
• Circuit board
• Cluster
• Computer data lines system
• D64
• D65
• Electrohydraulic control unit assembly
• Eng ctrl drct batt fd
• Fuse m1 15a
• Fuse m15 20a
• Fuse m28 15a
• Fuse m37 10a
• Gnd
• Hot at all times
• Hot w/ run/ start relay energized
• Ignition win wireless node
• Input spd (n2) sig+
• Input spd (n3) sig+
• K122
• K124
• K126
• K167
• K22
• K23
• K29
• K400
• K852
• K854
• K855
• K922
• L51
• Nca
• Pos 1 snsr fd
• Pos 1 snsr sig
• Pos 2 snsr fd
• Pos 2 snsr sig
• Postn snsr rtn
• Postn snsr rtn 2
• Powertrain control module (right front of engine compt)
• Prim snsr fd1
• Red
• S124
• S352
• S353
• S388
• Spd snsr rtn
• Stp lmp sig
• T13
• T70
• T71
• Tan/red
• Throttle body (top of front of engine)
• Thrtl pos mtr pos
• Thrtl pos snsr rtn
• Thrtl pos snsr sig 1
• Thrtl pos snsr sig 2
• Totally integrated power module (left side of engine compt)
• Transmission control module (left side of dash)
• Z909

6.4L, Cruise Control Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for 6.4L, Cruise Control Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013:

• (left front of engine, in multiple displacement solenoid harness) s270
• Adaptive cruise control module (center of front fascia)
• Brake sig
• Brake sig 2
• C139
• C315
• Can c (+)
• Can c (-)
• Clstr/chmsl batt
• Computer data lines system
• D507
• D51
• D52
• D64
• D65
• Dimm sw
• Evic rmux sig 1
• Evic/nav rmux rtn
• F943
• G909a (right rear of engine compt)
• G912a (under front of center console)
• G923a (left "d" pillar)
• Gnd
• Horn switch
• Hrn sw sig
• Htd str whl sig
• Ign rs
• Left remote/radio paddle switch
• Left steering wheel switch
• Lin sccm
• Red
• Rem rad ctrl sw sig
• Rem rad sw snce rtn
• Rem rad sw snse rtn
• Right remote/radio paddle switch
• S145
• S271
• S272
• S273
• S274
• Speed control switch
• Steering control module (steering column)
• Steering wheel heater sensor
• Stop lamp switch (on brake pedal assembly)
• Stp lmp sig
• Sw sig
• Sw spd ctrl rtn
• Sw spd ctrl snse 1
• Sw spd ctrl snse 2
• Tan/red
• Trx
• V71
• V72
• V937
• Z909
• Z912

DEFOGGERS

Defoggers Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Defoggers Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• (+)
• (-)
• A/c heater module
• Bus bar
• C16
• C160
• C17
• C170
• C395
• Can ihs
• Can ihs (+)
• Can ihs (-)
• Circuit board
• Computer data lines system
• D264
• D265
• Driv
• Driver door module
• Driver heated mirror
• Drv heated mirror fd
• Drv heated mirror rtn
• Drv heated mrr fd
• Ebl rly ctrl
• Electric heated backlite
• Fuse j12 30a
• G924a (right "d" pillar)
• Hot at all times
• Htr mrr rtn
• Htr rtn
• Nca
• Pass heated mirror fd
• Pass heated mirror rtn
• Pass heated mrr fd
• Pass mrr
• Passenger door module
• Passenger heated mirror
• Rear window defogger relay
• Totally integrated power module (left side of engine compt)

ELECTRONIC POWER STEERING

Electronic Power Steering Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Electronic Power Steering Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• Batt feed
• Can c (+)
• Can c (-)
• Computer data lines system
• Fuse 3 100a
• Fuse block
• Fuse m15 20a
• G906a (front of engine compt)
• Gnd
• Hot at all times
• Hot w/ run/start relay energized
• Ign rs
• Nca
• Power steering pump motor (lower right front of engine)
• Red
• S353
• Totally integrated power module (left side of engine compt)

ELECTRONIC SUSPENSION

Electronic Suspension Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Electronic Suspension Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• (base of left "c" pillar) g916a
• A206
• Accel snsr pwr ft lt
• Accel snsr pwr ft rt
• Accel snsr pwr rr
• Accel snsr rtn ft lt
• Accel snsr rtn ft rt
• Accel snsr rtn rr
• Accel snsr sig ft lt
• Accel snsr sig ft rt
• Accel snsr sig rr
• Active damping control module (under driver seat)
• C315
• Can c (+)
• Can c (-)
• Computer data lines system
• D51
• D52
• Dmpr vlv ft lt(+)
• Dmpr vlv ft lt(-)
• Dmpr vlv ft rt(+)
• Dmpr vlv ft rt(-)
• Dmpr vlv pwr ft lt
• Dmpr vlv pwr ft rt
• Dmpr vlv pwr rr lt
• Dmpr vlv pwr rr rt
• Dmpr vlv rr lt(+)
• Dmpr vlv rr lt(-)
• Dmpr vlv rr rt(+)
• Dmpr vlv rr rt(-)
• Elec brk conn
• F943
• Fuse m02 20a
• Fuse m15 20a
• Gnd
• Hot at all times
• Hot w/ run/start relay energized
• Ign rs
• Left front acceleration sensor (behind left front corner of front bumper)
• Left front act damper valve (on left side of engine compt, near strut)
• Left rear act damper valve (under left side of rear of vehicle, on strut)
• Nca
• Rear acceleration sensor
• Right front acceleration sensor (behind right front corner of front bumper)
• Right front act damper valve (on right side of engine compt, near strut)
• Right rear act damper valve (under right side of rear of vehicle, on strut)
• S130
• S131
• S132
• S133
• S134
• S135
• S136
• S137
• S160
• S161
• S162
• S163
• S164
• S165
• S166
• S167
• S168
• S170
• S171
• S172
• S173
• S324
• S353
• Totally integrated power module (left side of engine compt)
• Z916

ENGINE PERFORMANCE

3.6L

3.6L, Engine Performance Wiring Diagram (1 of 5) for Jeep Grand Cherokee Laredo X 2013

List of elements for 3.6L, Engine Performance Wiring Diagram (1 of 5) for Jeep Grand Cherokee Laredo X 2013:

• (right front of engine compt) g903a
• A209
• A803
• Altr snse flnk to alt
• Asd ctrl fd
• C130
• C161
• C162
• C315
• Camshaft position solenoid 2/2 (front of left cylinder bank)
• Can c (+)
• Can c (-)
• Coil on plg drv 1
• Coil on plg drv 4
• Coil on plg drv 5
• Coil on plg drv 6
• Computer data lines system
• Cool temp sens sig
• Crk spd sens o/p
• Cshft post sens sig 4
• Cshft postn sens sig 3
• D64
• D65
• Eng ctrl com sens rtn
• Eng ctrl com snsr rtn 5
• Eng ctrl drct batt fd
• Eng ctrl run strt ign
• Exhst vvt sol drv
• Exhst vvt sol drv 2
• F202
• F342
• Fuel tank press sens sig
• G903a (right front of engine compt)
• Gen source fd
• Ground
• Iat sens sig
• Ign coil drv 2 sig
• Ign coil drv 3 sig
• Injector sig 1
• Injector sig 2
• Injector sig 3
• Injector sig 4
• Injector sig 5
• Injector sig 6
• Intk vvt sol drv2
• Intke vvt sol drv
• K10
• K11
• K12
• K122
• K124
• K125
• K126
• K13
• K14
• K141
• K15
• K16
• K17
• K18
• K19
• K199
• K21
• K22
• K24
• K242
• K243
• K276
• K277
• K38
• K41
• K42
• K43
• K44
• K441
• K444
• K445
• K58
• K76
• K78
• K855
• K856
• K900
• K902
• K904
• K917
• K922
• K924
• K942
• K99
• Knock sens 1 return
• Knock sens 1 sig
• Knock sens 2 return
• Knock sens 2 sig
• Knock sensor 2 (top center of engine)
• Map sens sig
• O2 1/1 sig
• O2 1/1 upstrm htr fd
• O2 1/2 sig
• O2 2/1 updtrm sens sig
• O2 2/1upstrm htr fd
• O2 2/2 sig
• O2 downstream sens rtn
• O2 upstream sens rtn
• Oil pressure sig
• Pnk/red knock sens 2 rtn
• Powertrain control module (right front of engine compt)
• Prim sens fd 1
• Prim sens fd 2
• Pstn sens sig
• Pstn sens sig 2
• Red
• S104
• S108
• Sig 2
• Snsr rtn
• Starting/ charging system
• Throttle body (right rear of engine)
• Thrtl mtr pos ctrl
• Thrtl pos sens sig 1
• Thrtl pos snsr rtn
• Thrtl pos snsr sig 2
• Tp pos ctrl
• Z903

3.6L, Engine Performance Wiring Diagram (2 of 5) for Jeep Grand Cherokee Laredo X 2013

List of elements for 3.6L, Engine Performance Wiring Diagram (2 of 5) for Jeep Grand Cherokee Laredo X 2013:

• Asd ctrl
• Auto shutdown relay
• B(+)
• Bus bar
• C161
• C316
• Circuit board
• Fuse m19 25a
• Fuse m21 20a
• Fuse m28 15a
• G903a (right front of engine compt)
• Gnd
• Hot at all times
• Htr fd
• Knock sens 1 rtn
• Knock sens 1 sig
• Knock sensor 1 (top center of engine)
• Nca
• Oxygen sensor 1/1 (right side of engine, in exhaust)
• Oxygen sensor 1/2 (right side of engine, in exhaust)
• Oxygen sensor 2/1 (left side of engine, in exhaust)
• Oxygen sensor 2/2 (left side of engine, in exhaust)
• Red
• S102
• S103
• S106
• S110
• Snsr rtn
• Snsr sig
• Totally integrated power module (left side of engine compt)

3.6L, Engine Performance Wiring Diagram (3 of 5) for Jeep Grand Cherokee Laredo X 2013

List of elements for 3.6L, Engine Performance Wiring Diagram (3 of 5) for Jeep Grand Cherokee Laredo X 2013:

• (right rear of engine) manifold absolute pressure (map) sensor
• A/c clutch
• B snsr rtn 5
• B(+)
• Bus bar
• C press sens sig
• C13
• C130
• C192
• C267
• C318
• Circuit board
• Clstr/chmsl batt fd
• Fuel level sensor
• Fuel pump module (top of fuel tank)
• Fuel pump relay
• Fuel tank pressure sensor
• Fuse m01 15a
• Fuse m15 20a
• Fuse m25 20a
• Fuse m33 10a
• G109
• G916a (base of left "c" pillar)
• Gnd
• Hot at all times
• Hot w/ run/start relay energized
• Intake air temperature sensor (right rear of engine)
• Lvl snsr rtn
• Map snsr sig
• Nca
• Pmp mtr fd
• Pmp rly fd
• Prim sens fd
• Primary sig
• Prmry sig nca
• S109
• S332
• S353
• S381
• Sens rtn
• Shift lever assembly
• Sig sndr lvl
• Snse sig 2 brk actv
• Snse sig brk actv
• Snsr fd 2
• Snsr lvl sig nca
• Snsr rtn
• Snsr rtn nca
• Stop lamp switch (on brake pedal assembly)
• Tan/red
• Totally integrated power module (left side of engine compt)
• Z916

3.6L, Engine Performance Wiring Diagram (4 of 5) for Jeep Grand Cherokee Laredo X 2013

List of elements for 3.6L, Engine Performance Wiring Diagram (4 of 5) for Jeep Grand Cherokee Laredo X 2013:

• Accelerator pedal position sensor (base of accelerator pedal)
• App 1 rtn
• App 2 rtn
• App 2 sig
• C130
• C161
• C162
• C315
• C318
• Camshaft position sensor (rear of right cylinder bank)
• Camshaft position sensor 2 (rear of left cylinder bank)
• Camshaft position solenoid 1/1 (front of right cylinder bank)
• Camshaft position solenoid 1/2 (front of right cylinder bank)
• Crankshaft position sensor (front of left cylinder bank)
• Eng ctrl com
• Engine coolant temperature sensor (rear of left cylinder bank)
• Fuel injectors (1, 3 & 5: top of right cylinder bank) (2, 4 & 6: top of left cylinder bank)
• G903a (right front of engine compt)
• Oil press snsr sig
• Oil pressure sensor (left side of engine)
• Oil temperature sensor (upper center of left side of engine)
• Pos 1sens
• Prim sens fd 2
• Pstn sens sig
• Pstn sens sig 2
• S101
• S104
• S105
• S107
• S160
• S392
• Sens fd 2
• Snsr fd 1
• Snsr fd 2
• Snsr o/p
• Snsr rtn
• Snsr sig 3
• Snsr sig 4

3.6L, Engine Performance Wiring Diagram (5 of 5) for Jeep Grand Cherokee Laredo X 2013

List of elements for 3.6L, Engine Performance Wiring Diagram (5 of 5) for Jeep Grand Cherokee Laredo X 2013:

• (front of left cylinder bank) camshaft position solenoid 2/1
• (left side of engine compt) evap/purge solenoid
• (lower right of front of engine) oil pump solenoid
• A/c clutch coil
• Apps 2 sig
• Asd ctrl fd 1
• Asd rtn
• B15
• B16
• Brk actv snse sig
• Brk actv snse sig 2
• C13
• C130
• C161
• C315
• Can ihs (+)
• Can ihs (-)
• Cluster
• Computer data lines system
• Evap system monitor switch (under left rear of vehicle)
• F342
• Fuel pump ctrl
• G24
• G62
• G903a (right front of engine compt)
• G916a (base of left "c" pillar)
• Gnd
• Ign rs
• Ignition capacitor (rear of top of left cylinder bank)
• Ignition capacitor 2 (rear of top of right cylinder bank)
• Ignition coils (1, 3 & 5: top of right cylinder bank) (2, 4 & 6: top of left cylinder bank)
• K107
• K167
• K23
• K29
• K299
• K31
• K399
• K400
• K51
• K52
• K70
• O2 1/2 dwnstrm htr fd
• O2 2/2 dwnstrm htr fd
• Oil temperature sig
• Ped pos 1 sens sig
• Postn sens rtn
• Postn sens rtn 2
• Powertrain control module (right front of engine compt)
• Pwm prg sig
• Pwm prg sol rtn
• Rad fan ssr fd
• Rly cntc ctrl
• S104
• S161
• S293
• S333
• Sol var oil press
• Starting/ charging system
• Strk sense sig
• Strke snse
• Strtr rly coil rtn
• T110
• T752
• Vacc pmp rly coil
• Vacuum pmp rly coil ctrl
• Vacuum pump (upper front of right side of engine)
• Vacuum pump fuse holder (right rear of engine compt)
• Vacuum pump relay

5.7L

5.7L, Engine Performance Wiring Diagram (1 of 5) for Jeep Grand Cherokee Laredo X 2013

List of elements for 5.7L, Engine Performance Wiring Diagram (1 of 5) for Jeep Grand Cherokee Laredo X 2013:

• (right front of engine compt) g903a
• A209
• A803
• Altr snse flnk to alt
• Ascd ctrl
• Asd ctrl fd
• Auto shutdown relay
• B(+)
• Bus bar
• C161
• C192
• C315
• C316
• Can c (+)
• Can c (-)
• Circuit board
• Cmp sens sig
• Coil on plg drv 1
• Coil on plg drv 2
• Coil on plg drv 3
• Coil on plg drv 4
• Coil on plg drv 5
• Coil on plg drv 6
• Coil on plg drv 7
• Coil on plg drv 8
• Computer data lines system
• Cool temp sens sig
• Crk spd sens o/p
• D64
• D65
• Eng ctrl com sens rtn
• Eng ctrl drct batt fd
• Eng ctrl run strt ign
• F202
• F342
• F855
• F856
• Fuse m19 25a
• Fuse m21 20a
• Fuse m28 15a nca
• G903a (right front of engine compt)
• Gen source fd
• Ground
• Hot at all times
• Hot at all times nca
• Iat sens sig
• Ign ulk/run/strt
• Injector sig 1
• Injector sig 2
• Injector sig 3
• Injector sig 4
• Injector sig 5
• Injector sig 6
• Injector sig 7
• Injector sig 8
• K10
• K11
• K12
• K122
• K124
• K125
• K126
• K13
• K14
• K141
• K15
• K16
• K199
• K21
• K22
• K24
• K242
• K243
• K26
• K28
• K38
• K41
• K42
• K43
• K44
• K452
• K453
• K58
• K85
• K86
• K900
• K902
• K904
• K917
• K922
• K924
• K93
• K942
• K97
• K98
• K99
• Knock sens 1 return
• Knock sens 1 sig
• Knock sens 2 return
• Knock sens 2 sig
• Left knock sensor 1 (lower center of left side of engine)
• Map sens sig
• Nca
• O2 1/1 sig
• O2 1/1 upstrm htr fd
• O2 1/2 sig
• O2 2/1 updtrm sens sig
• O2 2/1upstrm htr fd
• O2 2/2 sig
• O2 downstream sens rtn
• O2 upstream sens rtn
• Oil pressure sig
• Pnk/red
• Pnk/red knock sens 2 return
• Powertrain control module (right front of engine compt)
• Press sns sig
• Prim sens fd 1
• Prim sens fd 2
• Red
• Run/start ign ulk/
• S110
• S124
• S331
• Sig 2
• Snsr rtn
• Snsr rtn 5
• Sol mds cyl 4
• Sol mds cyl 6
• Starting/ charging system
• Throttle body (top of front of engine)
• Totally integrated power module (left side of engine compt)
• Tp mtr pos ctrl
• Tp sens return
• Tp sens sig 1
• Tp sens sig 2
• Z903

5.7L, Engine Performance Wiring Diagram (2 of 5) for Jeep Grand Cherokee Laredo X 2013

List of elements for 5.7L, Engine Performance Wiring Diagram (2 of 5) for Jeep Grand Cherokee Laredo X 2013:

• (left side of engine, in exhaust)
• (right rear of engine) manifold absolute pressure (map) sensor
• (top of fuel tank)
• 87a
• B(+)
• Bus bar
• C161
• C192
• C267
• C318
• Circuit board
• Clstr/chmsl batt fd
• Fl sndr sig pmry
• Fuel level sensor
• Fuel pump module
• Fuel pump relay
• Fuel sndl lvl secondary
• Fuel tank pressure sensor
• Fuse m01 15a
• Fuse m25 20a
• Fuse m33 10a
• G109
• G903a (right front of engine compt)
• G916a
• G923a (left "d" pillar)
• Gnd
• Hot at all times
• Hot at all times nca
• Hot w/ run/start relay energized
• Htr fd
• Intake air temperature sensor (top front of engine)
• Lvl snsr rtn
• Map snsr sig
• Nca
• Oxygen sensor 1/1
• Oxygen sensor 1/2 (left side of engine, in exhaust)
• Oxygen sensor 2/1 (right side of engine, in exhaust)
• Oxygen sensor 2/2 (right side of engine, in exhaust)
• Pmp mtr fd
• Pmp rly fd
• Press snsr sig
• Prim snsr fd
• Prmry sig nca
• Run/strt
• S114
• S115
• S122
• S125
• S381
• Scndry sig nca
• Sens rtn
• Shift lever assembly
• Snse sig 2 brk actv
• Snse sig brk actv
• Snsr fd 2
• Snsr rtn
• Snsr rtn 5
• Snsr rtn nca
• Snsr sig
• Stop lamp switch (on brake pedal assembly)
• Tan/red
• Totally integrated power module (left side of engine compt)
• Z916

5.7L, Engine Performance Wiring Diagram (3 of 5) for Jeep Grand Cherokee Laredo X 2013

List of elements for 5.7L, Engine Performance Wiring Diagram (3 of 5) for Jeep Grand Cherokee Laredo X 2013:

• (left side of engine) oil pressure sensor
• (lower right front of engine) oil temperature sensor
• 5 volt sply
• Accelerator pedal position sensor (base of accelerator pedal)
• App 1 rtn
• App 1 sig
• App 2 rtn
• App 2 sig
• Asd ctrl
• C161
• C315
• Camshaft position sensor (front of right cylinder bank)
• Crankshaft position sensor (front of left cylinder bank)
• Crk spd snsr o/p
• Engine coolant temperature sensor (top front of engine)
• Fd 3
• Fuel injectors (1, 3, 5 & 7: top of left cylinder bank) (2, 4, 6 & 8: top of right cylinder bank)
• Ignition capacitor (rear of top of left cylinder bank)
• Ignition capacitor 2 (rear of top of right cylinder bank)
• Ignition coils (1, 3, 5 & 7: top of left cylinder bank) (2, 4, 6 & 8:top of right cylinder bank)
• Line pressure sensor (right rear of transmission)
• Line sens
• Oil press sig
• S111
• S113
• S119
• S120
• S121
• S123
• S333
• S392
• Sens fd 2
• Sens rtn
• Snsr fd 1
• Snsr fd 2
• Snsr rtn
• Snsr sig

5.7L, Engine Performance Wiring Diagram (4 of 5) for Jeep Grand Cherokee Laredo X 2013

List of elements for 5.7L, Engine Performance Wiring Diagram (4 of 5) for Jeep Grand Cherokee Laredo X 2013:

• (left front of engine) variable camshaft timing solenoid
• (left side of engine compt) evap/purge solenoid
• (left side of transmission) input speed sensor
• (left side of transmission) output speed sensor
• (right front of engine compt) g903a
• (under engine)
• (under left rear of vehicle) evap system monitor switch
• 2c ctrl
• 2c pre sig
• 4c ctrl
• 4c pre sig
• Batt fd
• C101
• C315
• G916a (base of left "c" pillar)
• Gnd
• L/r ctrl
• L/r pre sig
• Lp vfs ctrl
• Ms ctrl
• Multi displacement system cylinder 1 solenoid
• Multi displacement system cylinder 4 solenoid
• Multi displacement system cylinder 6 solenoid
• Multi displacement system cylinder 7 solenoid
• Od ctrl
• Od pre sig
• P/n sig
• S116
• S122
• S157
• Sens rtn
• Snse sig
• Transmission solenoid/pressure switch assembly
• Trns temp sig
• Trs t1
• Trs t3
• Trs t4
• Trs t42
• Ud ctrl
• Ud pre sig

5.7L, Engine Performance Wiring Diagram (5 of 5) for Jeep Grand Cherokee Laredo X 2013

List of elements for 5.7L, Engine Performance Wiring Diagram (5 of 5) for Jeep Grand Cherokee Laredo X 2013:

• 2c pressure sw sns
• 2c solenoid ctrl
• 4c ctrl
• 4c pressure sw sns
• A/c clutch coil
• App 1 sig
• Apps 1 return
• Apps 2 return
• Apps 2 sig
• Asd ctrl fd 1
• Asd rly fd
• Asd rtn
• B15
• B16
• Brk actv snse sig
• Brk actv snse sig 2
• C (-) can
• C13
• C161
• C315
• Can c (+)
• Can ihs (+)
• Can ihs (-)
• Circuit board
• Cluster
• Computer data lines system
• D64
• D65
• F342
• Fuel pump ctrl
• Fuse j18 20a nca
• G24
• G306
• G903a (right front of engine compt)
• Ground
• Hot at all times
• Input speed sig
• K107
• K167
• K23
• K29
• K299
• K31
• K399
• K400
• K442
• K451
• K454
• K51
• K52
• K70
• L/r pressure sw sns
• Line press sens sig
• Lp vfs ctrl
• Lr/cc ctrl
• Nca
• O2 (1/2) dwnstrm htr fd
• O2 (2/2) dwnstrm htr fd
• Od pressure sw sns
• Od solenoid ctrl
• Oil temperature sig
• Output speed sig
• P/n sig
• Powertrain control module (right front of engine compt)
• Pwm prg sig
• Pwm prg sol rtn
• S117
• Sol mds cyl1
• Sol mds cyl7
• Speed sens rtn
• Starting/ charging system
• Strk sense sig
• Strtr rly coil rtn
• Sw batt fd
• T118
• T13
• T14
• T140
• T147
• T15
• T16
• T20
• T219
• T259
• T29
• T38
• T41
• T42
• T48
• T50
• T52
• T54
• T59
• T60
• T752
• Totally integrated power module (left side of engine compt)
• Trans ms fr lr
• Transmission control relay
• Transmission temp sig
• Trs t1
• Trs t3
• Trs t4
• Trs t42
• Ud pressure sw sns
• Ud solenoid ctrl
• Vct sig
• Z903

6.4L

6.4L, Engine Performance Wiring Diagram (1 of 5) for Jeep Grand Cherokee Laredo X 2013

List of elements for 6.4L, Engine Performance Wiring Diagram (1 of 5) for Jeep Grand Cherokee Laredo X 2013:

• 5v eng tertiary fd
• 87a
• Asd ctrl fd 4
• Auto shut down relay
• B(+)
• B15
• B16
• Brake sig
• Brake sig 2
• Brk actv snse sig
• Brk actv snse sig 2
• Bus bar
• C161
• C315
• C316
• C318
• Can c (+)
• Can c (-)
• Circuit board
• Clstr/chmsl batt
• Computer data lines system
• D64
• D65
• Eng ctrl run/strt ign fuel tank press
• F202
• Fuel level sensor
• Fuel lvl snsr rtn
• Fuel pmp mtr fd
• Fuel pump module (top of fuel tank)
• Fuel pump relay
• Fuel sndr lvl sig primary
• Fuel snsr lvl sig secondary/sw
• Fuel tank press snsr sig
• Fuel tank pressure sensor
• Ful pmp rly fd to sec rly or rstr
• Ful sndr lvl sig secondary
• Fuse m1 15a
• Fuse m19 25a
• Fuse m21 20a
• Fuse m25 20a
• Fuse m28 15a
• Fuse m33 10a
• Fuse m37 10a
• G109
• G916a (base of left "c" pillar)
• G923a (left "d" pillar)
• Gnd
• Hot at all times
• Hot at all times nca
• Hot w/ run/ start relay energized
• Ign rs
• K859
• L51
• Nca
• Powertrain control module (right front of engine compt)
• Red
• S332
• S352
• S381
• S388
• Stop lamp switch (on brake pedal assembly)
• Stp lmp sig
• Tan/red
• Totally integrated power module (left side of engine compt)
• Z916

6.4L, Engine Performance Wiring Diagram (2 of 5) for Jeep Grand Cherokee Laredo X 2013

List of elements for 6.4L, Engine Performance Wiring Diagram (2 of 5) for Jeep Grand Cherokee Laredo X 2013:

• (base of accelerator pedal) accelerator pedal position sensor
• (left front of engine) variable camshaft timing solenoid
• (under engine) multi displacement system solenoid (cylinder 1)
• (under engine) multi displacement system solenoid (cylinder 4)
• (under engine) multi displacement system solenoid (cylinder 6)
• (under engine) multi displacement system solenoid (cylinder 7)
• A/c cltch coil
• A209
• Accel ped pos 1 snsr fd
• Accel ped pos 1 snsr sig
• Accel ped pos 2 snsr fd
• Accel ped pos 2 snsr sig
• Accel ped pos snsr rtn
• Accel ped postn snsr rtn
• Accel ped postn snsr rtn 2
• Air conditioning system
• Asd ctrl fd 1
• Asd rtn
• C101
• C13
• C161
• C202
• C315
• Can c (+)
• Can c (-)
• Can ihs (+)
• Can ihs (-)
• Cluster
• Computer data lines system
• D65
• Eng ctrl com snsr rtn 5
• Eng ctrl drct batt fd
• Eng ctrl fuel pump sig
• Evap system monitor switch (under left rear of vehicle)
• F342
• G903a (right front of engine compt)
• G909a (right rear of engine compt)
• G916a (base of left "c" pillar)
• Gnd
• K107
• K167
• K23
• K29
• K31
• K400
• K51
• K52
• K70
• K852
• K854
• K917
• Leak detcn sw snse
• Leak dtctn sw sig
• Powertrain control module (right front of engine compt)
• Pwm prg sig
• Pwm prg sol rtn
• Red
• S270
• S333
• Sol mds cyl 1
• Sol mds cyl 4
• Sol mds cyl 6
• Sol mds cyl 7
• Starting/ charging system
• Stp lmp sig
• Strtr ovrde rly coil rtn
• T752
• Vct sig
• Wireless ignition node
• Z909

6.4L, Engine Performance Wiring Diagram (3 of 5) for Jeep Grand Cherokee Laredo X 2013

List of elements for 6.4L, Engine Performance Wiring Diagram (3 of 5) for Jeep Grand Cherokee Laredo X 2013:

• (front of left cylinder bank) crankshaft position sensor
• (front of right cylinder bank) camshaft position sensor
• (right rear of engine) manifold absolute pressure sensor
• (top front of engine) engine coolant temperature sensor
• Asd ctrl fd 1
• C161
• C192
• C267
• C315
• Cam postn snsr sig
• Cool temp snsr sig
• Crk spd snsr outpt
• Crkshft postn snsr rtn
• Eng ctrl com snsr rtn
• Evap/purge solenoid (left side of engine compt)
• Exhaust differential pressure sensor
• Exhst gas press sig
• Fuel inj 1 sig
• Fuel inj 2 sig
• Fuel inj 3 sig
• Fuel inj 4 sig
• Fuel inj 5 sig
• Fuel inj 6 sig
• Fuel inj 7 sig
• Fuel inj 8 sig
• Fuel injector 1 (top of left cylinder bank)
• Fuel injector 2 (top of right cylinder bank)
• Fuel injector 3 (top of left cylinder bank)
• Fuel injector 4 (top of right cylinder bank)
• Fuel injector 5 (top of left cylinder bank)
• Fuel injector 6 (top of right cylinder bank)
• Fuel injector 7 (top of left cylinder bank)
• Fuel injector 8 (top of right cylinder bank)
• Map snsr sig
• Prim snsr fd 1
• Prim snsr fd 2
• Pwm prg
• S111
• S113
• S119
• S125
• Shift lever assembly
• Sig pwm prg
• Snsr rtn eng ctrl com
• Sol rtn

6.4L, Engine Performance Wiring Diagram (4 of 5) for Jeep Grand Cherokee Laredo X 2013

List of elements for 6.4L, Engine Performance Wiring Diagram (4 of 5) for Jeep Grand Cherokee Laredo X 2013:

• (left side of engine) oil pressure sensor
• (left side of engine, in exhaust) oxygen sensor 1/1
• (lower center of left side of engine) left knock sensor 1
• (lower center of right side of engine) right knock sensor 2
• (lower right front of engine) oil temperature sensor
• (right side of engine, in exhaust) oxygen sensor 2/1
• (top front of engine) intake air temperature sensor
• A804
• Altr fld fd
• Altr snse flnk to mod
• Coil on plg drv 1
• Coil on plg drv 2
• Coil on plg drv 3
• Cool temp snsr sig
• Eng ctrl com snsr rtn
• Eng ctrl com snsr rtn 3
• Fuel inj 1 sig
• Fuel inj 2 sig
• Fuel inj 3 sig
• Fuel inj 4 sig
• G24
• G903a (right front of engine compt)
• Gnd
• Intke temp snsr sig
• K11
• K12
• K124
• K126
• K13
• K14
• K141
• K20
• K21
• K242
• K243
• K299
• K41
• K42
• K43
• K442
• K451
• K452
• K453
• K85
• K86
• K902
• K904
• K924
• K93
• K942
• K99
• Map snsr sig
• O2 (1/1) upstrm htr fd
• O2 (1/1) upstrm snsr sig
• O2 (1/2) dnstrm htr fd
• O2 (1/2) dnstrm snsr sig
• O2 (2/1) upstrm htr fd
• O2 (2/1) upstrm snsr sig
• O2 (2/2) dwstrm snsr sig
• O2 dnstrm snse rtn
• O2 upstrm snse rtn
• O2 upstrm snsr rtn
• Oil press snse /sw sig
• Oil press snse/ sw sig
• Powertrain control module (right front of engine compt)
• Prim snsr fd 1
• S114
• S162
• Sig for qual snsr eng oil temp
• Snsr eng oil temp sig for qual
• Snsr knock 1 rtn
• Snsr knock 1 sig
• Snsr knock 2 rtn
• Snsr knock 2 sig
• Sol mds cyl 1
• Sol mds cyl 4
• Sol mds cyl 6
• Starting/ charging system
• Thrtl pos mtr pos ctrl
• Vct sig

6.4L, Engine Performance Wiring Diagram (5 of 5) for Jeep Grand Cherokee Laredo X 2013

List of elements for 6.4L, Engine Performance Wiring Diagram (5 of 5) for Jeep Grand Cherokee Laredo X 2013:

• (left side of engine, in exhaust) oxygen sensor 1/2
• (right side of engine, on exhaust) oxygen sensor 2/2
• (top of front of engine) throttle body
• (top of left cylinder bank)
• (top of right cylinder bank)
• Asd ctrl fd 3
• C161
• Cam postn snsr sig
• Coil on plg driv 1
• Coil on plg driv 2
• Coil on plg driv 3
• Coil on plg driv 4
• Coil on plg driv 5
• Coil on plg driv 6
• Coil on plg driv 7
• Coil on plg driv 8
• Coil on plg drv 4
• Coil on plg drv 5
• Coil on plg drv 6
• Coil on plg drv 7
• Coil on plg drv 8
• Crkshft postn snsr rtn
• Crnk spd snsr outpt
• Eng ctrl com snsr rtn
• Eng ctrl com snsr rtn 3
• Exhst gas press sig
• F856
• Fuel inj 5 sig
• Fuel inj 6 sig
• Fuel inj 7 sig
• Fuel inj 8 sig
• G903a (right front of engine compt)
• Gnd
• Ignition capacitor (rear of top of left cylinder bank)
• Ignition capacitor 2 (rear of top of right cylinder bank)
• Ignition coil 1
• Ignition coil 2
• Ignition coil 3
• Ignition coil 4
• Ignition coil 5
• Ignition coil 6
• Ignition coil 7
• Ignition coil 8
• K10
• K122
• K15
• K16
• K199
• K22
• K237
• K238
• K24
• K26
• K28
• K373
• K38
• K399
• K44
• K454
• K58
• K855
• K900
• K915
• K922
• K925
• K97
• K98
• O2 (1/2) dnstrm htr fd
• O2 (1/2) dnstrm snsr sig
• O2 (2/1) upstrm htr fd
• O2 (2/2) dnstrm htr fd
• O2 (2/2) dnstrm snsr sig
• O2 dnstrm snse rtn
• Powertrain control module (right front of engine compt)
• Prim snsr fd 1
• Prim snsr fd 2
• S115
• S120
• S121
• S124
• Short runner solenoid valve
• Sol mds cyl 7
• Srv act ctrl sig
• Srv snse outpt
• Thrtl pos mtr pos ctrl
• Thrtl pos sensr rtn
• Thrtl pos sensr sig 1
• Thrtl pos sensr sig 2
• Thrtl pos snsr rtn
• Thrtl pos snsr sig 1
• Thrtl pos snsr sig 2

EXTERIOR LIGHTS

Backup Lamps Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Backup Lamps Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• (right "d" pillar) g924a
• B(+)
• Backup lamp fd
• Bkup lmps fd
• C202
• C204
• C390
• Can c (+)
• Can c (-)
• Circuit board
• Computer data lines system
• D64
• D65
• G912a (under front of center console)
• G916a (base of left "c" pillar)
• G924a (right "d" pillar)
• Gnd
• Hot at all times
• Inside rearview mirror
• Left liftgate lamp
• Left tail lamp assembly
• Nca
• Powertrain control module (5.7l) (right front of engine compt)
• Right liftgate lamp
• Right tail lamp assembly
• S334
• S335
• S357
• T42
• Totally integrated power module (left side of engine compt)
• Trailer tow 7-way wiring (under rear of vehicle)
• Trans rng t1 sig
• Trans rng t3 sig
• Trans rng t4 sig
• Trans rng t42 sig
• Transmission control module (6.4l & 3.6l) (left side of dash)
• Transmission solenoid/ trs assembly

Exterior Lamps Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for Exterior Lamps Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013:

• (in body harness) s364
• (in ip harness) s364
• (info not available)
• 6.4l
• A909
• B(+)
• B15
• B16
• Batt fd 9
• Brk actv sens sig
• Brk actv sens sig 2
• C202
• C315
• C390
• Can c (+)
• Can c (-)
• Can ihs (+)
• Can ihs (-)
• Center console lamp
• Circuit board
• Clstr/chmsl batt fd stp lmp sig
• Cluster
• Computer data lines system
• D264
• D265
• D51
• D52
• Except 6.4l
• Fd 1 fog lmp/ind
• Fuse m1 15a
• Fuse m18 15a
• Fuse m20 15a
• Fuse m37 10a
• G901a (left rear of engine compt)
• G912a (under front of center console)
• G923a (left "d" pillar)
• G924a (right "d" pillar)
• Gnd
• Gnd brk actv sens sig
• Hazard sw sig
• Hd/fog lp
• Hdlp lvng sw sig
• Headlamp switch
• Hot at all times
• Hot w/ run/ start relay energized
• Ign rs brk actv sens sig 2
• L133
• L160
• L161
• L51
• L62
• L63
• L777
• L78
• L91
• Lamps 2
• Left drl lamp
• Left front lamp assembly
• Lf prk/tl
• Lf trn sig ind
• License plate lamp/ rear camera assembly (center of tailgate)
• Lin ccn
• Lt ft prk/ tl lmps 2
• Mlfnct sw rtn
• Nca
• Powertrain control module (right front of engine compt)
• Red
• Rt ft prk/ tl lmps 1
• Rt ft prk/tl lmps 1
• Rt rf turn sig ind
• S127
• S138
• S231
• S335
• S338
• S352
• S388
• Sens sig stp lmp
• Sig fd lf trn
• Sig fd lt rr trn
• Sig fd rt ft trn
• Sig fd rt rr turn
• Steering control module (steering column)
• Stop lamp switch (on brake pedal assembly)
• Stp lmp sig
• Sw sig hazard
• Tan/red
• Totally integrated power module (left side of engine compt)
• Upper bank switch
• Wireless ignition node (left side of dash)
• Z912

Exterior Lamps Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for Exterior Lamps Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013:

• (left side of engine compt) power distribution center
• Backup lamps circuit
• Backup lmp
• Bkup lmps fd
• Brake provision module (left kick panel)
• Bus bar
• C100
• C139
• C392
• Center high mounted stop lamp
• Fuse j14 20a
• Fuse m35 15a
• G901a
• G909a (right rear of engine compt)
• G916a (base of left "c" pillar)
• G923a (left "d" pillar)
• G924a (right "d" pillar)
• Gnd
• Hot at all times
• L56
• Left liftgate lamp
• Left tail lamp assembly
• Liftgate unlock relay
• Lmps 1 rt ft prk/tl
• Lt ft prk/tl lmps 1
• Lt rr trn sig fd
• Nca
• Park lamp relay
• Prk lp rly ctrl
• Right drl lamp
• Right front lamp assembly
• Right liftgate lamp
• Right tail lamp assembly
• Rr rt turn sig fd
• Rt ft prk/tl lmps 1
• Rt trn sig fd
• S126
• S127
• S128
• S335
• S360
• S363
• Stp lmp sens sig
• Stp lmp sig
• Totally integrated power module engine compt) (left side of
• Trailer tow 7-way wiring (under rear of vehicle)
• Z916

Trailer Tow Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Trailer Tow Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• A114
• B400
• Backup lamps circuit
• Brake provision module (left kick panel)
• Brk output
• C316
• Circuit board
• Computer data lines system
• Ctrl rly lt ttow
• Ctrl rly rt ttow
• D264
• D265
• Exterior lamps circuit
• Fuse j3 40a
• Fuse j9 30a
• G916a (base of left "c" pillar)
• G923a (left "d" pillar)
• Gnd
• Hot at all times
• Ihs (+) can
• Ihs (-) can
• Iod snse
• L56
• L673
• L674
• Nca
• Nca b(+)
• Red
• Stp lmp sig
• Totally integrated power module (left side of engine compt)
• Trailer tow 7-way wiring (under rear of vehicle)
• Ttow elec
• Z916

GROUND DISTRIBUTION

Ground Distribution Wiring Diagram (1 of 3) for Jeep Grand Cherokee Laredo X 2013

List of elements for Ground Distribution Wiring Diagram (1 of 3) for Jeep Grand Cherokee Laredo X 2013:

• (4wd) drive train control module
• (if equipped)
• (if equipped) active damping control module
• (if equipped) electronic limited slip differential module
• (if equipped) headlamp washer motor
• (w/o memory) driver seat switch
• 5.7l & 6.4l
• Anti lock brakes module
• B c4
• Blind spot module
• Brake fluid level sensor
• C101
• C138
• C2 c
• C267
• C318
• C353
• C389
• C663
• Cigar lighter
• Cluster
• Console power outlet
• Cupholder lamp
• D c2
• Driver lumbar seat adjuster switch
• Evap system monitor switch
• From splice s106 (diagram 2 of 3)
• Front blower motor power module
• Fuel door solenoid
• Fuel pump module
• G901a
• G904 (left side of engine)
• G905 (left front of engine)
• G911a (left side of dash)
• G916a (base of left "c" pillar)
• Glove box lamp
• Headlamp switch
• Left drl lamp
• Left front fog lamp
• Left front headrest solenoid
• Left front lamp assembly
• Left rear blind spot sensor
• Left rear seat cushion heater
• Left seat cushion heater
• Left tail lamp assembly
• Lower left courtesy lamp
• Lower right courtesy lamp
• Memory seat module
• Multi displacement system cylinder 1 solenoid
• Multi displacement system cylinder 4 solenoid
• Multi displacement system cylinder 6 solenoid
• Multi displacement system cylinder 7 solenoid
• Prndl lamp
• Right drl lamp
• Right rear blind spot sensor
• S127
• S157 (5.7l) s270 (6.4l) (6.4l: left front of engine, in multiple displacement solenoid harness)
• S339
• S348
• S408
• Shift lever assembly
• Tire pressure module
• Trailer tow 7-way wiring
• Transfer case selector switch
• Variable camshaft timing solenoid

Ground Distribution Wiring Diagram (2 of 3) for Jeep Grand Cherokee Laredo X 2013

List of elements for Ground Distribution Wiring Diagram (2 of 3) for Jeep Grand Cherokee Laredo X 2013:

• (3.6l) vacuum pump
• (6.4l) oxygen sensor 1/1
• (6.4l) oxygen sensor 1/2
• (6.4l) oxygen sensor 2/1
• (6.4l) oxygen sensor 2/2
• (6.4l) short runner solenoid valve
• (if equipped) brake provision module
• (if equipped) power steering pump motor
• (left side of engine compt) totally integrated power module
• 3.6l
• 5.7l
• 5.7l & 3.6l
• 5.7l & 6.4l
• 87a
• A/c heater control
• C139 (3.6l)
• C204
• C266
• C301
• C320
• C383
• Camshaft 1/1 position solenoid
• Camshaft 1/2 position solenoid
• Camshaft position solenoid 2/1
• Camshaft position solenoid 2/2
• Center console lamp
• Center high mounted stop lamp
• Cluster
• Data link connector
• Door lock relay
• Driver door latch
• Driver door module
• Driver door unlock relay
• Driver window/ door lock switch
• Dynamics sensor
• From totally integrated power module (diagram 3 of 3)
• Front washer pump relay
• G306
• G903a (right front of engine compt)
• G906a (right front of engine compt)
• G912a (under front of center console)
• G913a (under center console)
• G923a (left "d" pillar)
• Inside rearview mirror
• Left rear door latch
• Left rear heated seat switch
• Left rear power window switch
• Nca
• Occupant restraint controller module
• Oil pump solenoid
• Oxygen sensor 1/1
• Oxygen sensor 1/2
• Oxygen sensor 2/1
• Oxygen sensor 2/2
• Passenger door unlock relay
• Passive entry module
• Power liftgate chime
• Power liftgate module
• Powertrain control module
• Radiator cooling fan module
• Radio
• Radio amplifier
• Rain sensor
• Rear washer pump relay
• Rechargeable cargo lamp
• Right rear heated seat switch
• S104
• S106 (3.6l) s122 (5.7l)
• S340
• S501 (right side of engine, in engine harness)
• S700
• Steering control module
• Stop lamp switch
• To splice s157 (diagram 1 of 3)
• Transmission control relay
• Upper bank switch
• Video screen module
• Wireless ignition node

Ground Distribution Wiring Diagram (3 of 3) for Jeep Grand Cherokee Laredo X 2013

List of elements for Ground Distribution Wiring Diagram (3 of 3) for Jeep Grand Cherokee Laredo X 2013:

• (6.4l) powertrain control module
• (if equipped) adaptive cruise control module
• (if equipped) air suspension relay
• (if equipped) right front lamp assembly
• (if equipped) right rear seat cushion heater
• (if equipped) transmission control module
• (left side of engine compt) power distribution center
• (left side of engine compt) totally integrated power module
• (not used)
• 87a
• A/c compressor clutch
• C139
• C161
• C2 c
• C306
• C311
• C321
• C352
• C384
• C392
• C395
• C4 b
• C664
• Compass module
• Electric heated backlite
• Electronic overhead module
• Flip up glass latch
• Front wiper motor
• G909a (right rear of engine compt)
• G919a (base of right "c" pillar)
• G924a (right "d" pillar)
• Heated seat module
• Horn 1
• Horn 2
• Inverter module
• Left cargo lamp
• Left front grab handle lamp
• Left leftgate lamp
• Left vanity lamp
• License plate lamp/ rear camera assembly
• Liftgate unlock relay
• Nca
• Park assist module
• Passenger door latch
• Passenger door module
• Passenger lumbar seat adjuster switch
• Passenger seat switch
• Rear power outlet
• Rear wiper motor
• Right cargo lamp
• Right front fog lamp
• Right front grab handle lamp
• Right front headrest solenoid
• Right liftgate lamp
• Right rear door latch
• Right rear power window switch
• Right seat cushion heater
• Right tail lamp assembly
• Right vanity lamp
• S128
• S145
• S335
• S382
• S418
• S419
• S600 (in right front door harness)
• S800
• S905
• Sunroof motor
• Sunroof shade motor
• To g306 (diagram 2 of 3)
• Wiper on/off relay

HEADLIGHTS

Headlamps Wiring Diagram, with DRL for Jeep Grand Cherokee Laredo X 2013

List of elements for Headlamps Wiring Diagram, with DRL for Jeep Grand Cherokee Laredo X 2013:

• (right rear of engine compt) g909a
• 6.4l
• A/c heater module
• A417
• Auto hdlp sig
• Auto headlamps sig
• B (+)
• Batt fd 9
• C138
• C139
• C201
• C202
• C205
• Can c (+)
• Can c (-)
• Can ihs (+)
• Can ihs (-)
• Circuit board
• Cluster
• Compass module
• Computer data lines system
• D264
• D265
• D506
• D64
• D65
• Dim 3 ip
• Dimm sig sel
• Drl fd rt
• Drl ft all lt
• Drl sig
• Drl sig sig fd rt ft trn
• Except 6.4l
• Fd batt eatx
• Fog lmp/ ind fd 1
• Fuse m11 10a
• Fuse m14 20a
• Fuse m15 20a
• Fuse m20 15a
• Fuse m3 30a
• Fuse m34 10a
• G39
• G901a (left rear of engine compt)
• G909a (right rear of engine compt)
• G911a (left side of dash)
• G912a (under front of center console)
• Gnd
• Hdlp/fog lmp sel sw
• Headlamp switch
• Hot at all times
• Hot w/ run relay (on pcb) energized
• Hot w/ run relay energized
• Hot w/ run/ start relay energized
• Hzrd sig sw
• Ign r
• Ign rs
• Ind fd 2 fog lmp/
• Interior lights system
• Iod fd
• L24
• L33
• L34
• L43
• L44
• L57
• L60
• L777
• L78
• L90
• L91
• L910
• L911
• Left drl lamp
• Left drl relay
• Left front fog lamp
• Left front lamp assembly
• Lin ccn
• Lin ltng
• Lt all drl fd batt eatx
• Lt ft prk/tl lmps 2
• Lt hdlp rtn
• Lt hi beam fd
• Lt lo beam fd
• Mlfnct rtn sw
• Mlfnct sw rtn
• Park brk sw sig
• Parking brake switch (top of parking brake assembly)
• Pnk/tan
• Power distribution center (left side of engine compt)
• Red
• Right drl lamp
• Right drl relay
• Right front fog lamp
• Right front lamp assembly
• Rt fd drl
• Rt ft prk/tl lmps 1
• Rt ft trn sig fd
• Rt hdlp rtn
• Rt hi beam fd
• Rt lin ltng
• Rt lo beam
• Rt lo beam fd
• S126
• S127
• S128
• S129
• S138
• S139
• S231
• S237
• S302
• S353
• S391
• Sig fd rt ft trn
• Snsr sunld sig
• Sun sensor (center of top of dash)
• Totally integrated power module (left side of engine compt)
• Ttow ign fd
• Upper bank switch
• Z912

Headlamps Wiring Diagram, without DRL for Jeep Grand Cherokee Laredo X 2013

List of elements for Headlamps Wiring Diagram, without DRL for Jeep Grand Cherokee Laredo X 2013:

• (right rear of engine compt) g909a
• A/c heater module
• A417
• Auto hdlp sig
• Auto headlamps sig
• B (+)
• Batt fd 9
• C138
• C201
• C202
• C205
• Can c (+)
• Can c (-)
• Can ihs (+)
• Can ihs (-)
• Circuit board
• Cluster
• Compass module
• Computer data lines system
• D264
• D265
• D506
• D64
• D65
• Dim 3 ip
• Dimm sig sel
• Fog lmp/ind fd 2
• Fuse 20a
• Fuse holder 2
• Fuse m11 10a
• Fuse m20 15a
• Fuse m34 10a
• G39
• G901a (left rear of engine compt)
• G909a (right rear of engine compt)
• G911a (left side of dash)
• G912a (under front of center console)
• Gnd
• Hdlp/fog lmp sel sw
• Headlamp switch
• Hot at all times
• Hot w/ run relay energized
• Hzrd sig sw
• Ign r
• Interior lights system
• Iod fd
• L24
• L33
• L34
• L43
• L44
• L91
• L910
• L911
• Left front fog lamp
• Left front lamp assembly
• Lin ccn
• Lt hdlp rtn
• Lt hi beam fd
• Lt lo beam fd
• Mlfnct rtn sw
• Mlfnct sw rtn
• Park brk sw sig
• Parking brake switch (top of parking brake assembly)
• Power distribution center (left side of engine compt)
• Rad fan ssr fd
• Red
• Right front fog lamp
• Right front lamp assembly
• Rt hdlp rtn
• Rt hi beam fd
• Rt lin ltng
• Rt lo beam fd
• S127
• S128
• S129
• S139
• S237
• S291
• S293
• Snsr sunld sig
• Sun sensor (center of top of dash)
• Totally integrated power module (left side of engine compt)
• Upper bank switch
• Z912

Headlamps Leveling Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Headlamps Leveling Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• C139
• C315
• Front headlamp level sensor (center front of engine compt)
• Ft 5v hdlp lvlg snsr
• Ft hdlp lvlg snsr rtn
• Ft hdlp lvlg snsr rtn c1
• Ft hdlp lvlg snsr sig
• Fuse m34 10a nca
• G909a (right rear of engine compt)
• Gnd
• Hot w/ run relay energized nca
• Ign r
• Rear headlamp level sensor
• Right front lamp assembly
• Rr 5v hdlp lvlg snsr
• Rr hdlp lvlg snsr rtn
• Rr hdlp lvlg snsr sig
• S128
• S129
• S142
• S365
• Totally integrated power module (left side of engine compt)

HORN

Horn Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Horn Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• 87a
• Bus bar
• Can c (+)
• Can c (-)
• Circuit board
• Computer data lines system
• D507
• D51
• D52
• Fuse m22 10a nca
• Fuse m23 10a nca
• G909a (right rear of engine compt)
• Horn 1 (behind left side of radiator grille)
• Horn 2 (behind right side of radiator grille)
• Horn relay
• Horn relay coil drv
• Horn sw sig
• Horn switch
• Hot at all times
• Lin sccm
• Nca
• Rem rad sw snse rtn
• S145
• S272
• Sound systems
• Speed control switch
• Steering control module (steering column)
• Totally integrated power module (left side of engine compt)

INSTRUMENT CLUSTER

Instrument Cluster Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for Instrument Cluster Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013:

• (3.6l) s101 (5.7l & 6.4l) s113
• (3.6l) s108
• (right "d" pillar) g924a
• 110vac inv stat ind
• 3.6l & 5.7l
• 6.4l
• A412
• A909
• Astk up
• B25
• Batt fd 9
• C (-)
• C201
• C202
• Can
• Can c (+)
• Can ihs (+)
• Can ihs (-)
• Cluster
• Compass module
• Computer data lines system
• D264
• D265
• D506
• D64
• D65
• Dim 3 ip
• Dimm sig sel
• E12
• Eng ctrl com snsr rtn
• F921
• F943
• Fd 1
• Ft hdr crtsy fd
• Fuse m13 20a nca
• Fuse m15 20a nca
• Fuse m20 15a nca
• Fuse m34 10a nca
• G38
• G911a (left side of dash)
• G912a (under front of center console)
• Gnd
• Hdlp/fog lmp sel sw
• Headlights system
• Hot at all times
• Hot w/ run relay (on pcb) energized
• Hot w/ run/ start relay energized
• Ign r
• Ign rs
• Interior lights system
• Iod fd
• K855
• K900
• L116
• L900
• Lin ccn
• M24
• M27
• Mlfnct sw rtn
• Nca
• Oil press
• Overhead console circuit
• P806
• Park brk sw sig
• Parking brake switch (top of parking brake assembly)
• Power distribution system
• Powertrain control module (right front of engine compt)
• Prim snsr
• Prk brk sw sig
• Rail lmp fds
• Red
• S124 (5.7l & 6.4l)
• S231
• S246
• S327
• S902
• S905
• Shift interlock system
• Snse/sw sig
• Totally integrated power module (left side of engine compt)
• Ugdo disable
• Z911
• Z912
• Z923

Instrument Cluster Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for Instrument Cluster Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013:

• (left "d" pillar)
• 3.6l
• Ajar sig rt rr dr nca
• Ajar sw sig lt rr dr nca
• B(+)
• B20
• Brake fluid level sensor (left rear of engine compt)
• Brk lvl sw sig
• C162
• C300
• C305
• C316
• C318
• C383
• C384
• C392
• Can ihs (+)
• Can ihs (+) nca
• Can ihs (-)
• Can ihs (-) nca
• Circuit board
• Computer data lines system
• D264
• D265
• Driv ft dr ajar sw in
• Driver door latch
• Eng ctrl com snsr rtn
• Fuel level sensor
• Fuel lvl snsr rtn
• Fuel pump module (top of fuel tank)
• Fuel sndr lvl sig primary
• Fuel sndr lvl sig primary gnd
• Fuel sndr lvl sig secondary
• G109
• G74
• G75
• G76
• G77
• G78
• G901a (left rear of engine compt)
• G916a (base of left "c" pillar)
• G919a (base of right "c" pillar)
• G923a (left "d" pillar)
• Gnd
• Hot at all times nca
• Left rear door latch
• Lgate ajar sig
• Liftgate ajar sig
• Liftgate door latch
• Logic rtn
• Lt rr dr ajar sig gnd
• Nca
• Oil press snse/sw sig
• Oil pressure sensor (left side of engine)
• Pass ft dr ajar sw in
• Passenger door latch
• Power liftgate module
• Prim snsr fd 1
• Q901
• Right rear door latch
• Rt rr dr ajar sig gnd
• S336
• S355
• S381
• S501
• S600
• S700
• S800
• Sw sig brk lvl nca
• Totally integrated power module (left side of engine compt)
• Z916
• Z923

Overhead Console Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Overhead Console Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• A413
• C201
• C311
• C320
• C321
• Can ihs (+)
• Can ihs (-)
• Cluster
• Computer data lines system
• D264
• D265
• Dim 3 ip
• E12
• Electronic overhead module
• Ft hdr crsty fd
• Fuse m10 15a
• G25
• G38
• G912a (under front of center console)
• G924a (right "d" pillar)
• Gnd
• Hot at all times
• Interior lights system
• Iod fd
• Lgate sw ft sig
• M27
• Nca
• Power liftgate module (left "d" pillar)
• Q556
• Q56
• Rail lmp fds
• Red
• S328
• S905 m24
• Shade close(+)
• Shade opn (+)
• Sunrf pwr cls(+)
• Sunrf pwr opn(+)
• Sunrf swd rtn
• Sunrf vent(+)
• Sunroof motor
• Sunroof shade motor
• Totally integrated power module (left side of engine compt)
• Ugdo disable
• Ugdo disable (veh thef alrm on)
• Z919
• Z923

INTERIOR LIGHTS

Courtesy Lamps Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for Courtesy Lamps Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013:

• Ajar sig rt rr door nca
• B(+)
• Batt fd 9
• C202
• C300
• C305
• C321
• C383
• C384
• C392
• Can ihs (+)
• Can ihs (-)
• Circuit board
• Cluster
• Computer data lines system
• D264
• D265
• Driver door latch
• Drv dr ajar sw in
• Ft hdr crtsy fd
• Fuse m20 15a
• G74
• G75
• G76
• G77
• G78
• G911a (left side of dash)
• G912a (under front of center console)
• G919a (base of right "c" pillar)
• G923a (left "d" pillar)
• Glove box lamp
• Gnd
• Hdlp/fog lmp sel sw
• Headlamp switch
• Hot at all times
• Left rear door latch
• Lgate ajar sig
• Liftgate door latch
• Lower left courtesy lamp
• Lower right courtesy lamp
• Lt rr door ajar sig
• Nca
• Pass ft dr ajar sw in
• Passenger door latch
• Power liftgate module (left "d" pillar)
• Rail lmp fds
• Red
• Right rear door latch
• Rr door ajar sig
• S231
• S248
• S249
• S355
• S501
• S600
• S700
• S800
• Totally integrated power module (left side of engine compt)
• Z923

Courtesy Lamps Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for Courtesy Lamps Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013:

• (right "d" pillar) g924a
• A214
• A215
• B(+)
• Batt pre 3
• Bus bar
• C301
• C302
• C306
• C307
• C320
• C321
• C392
• Can ihs (+)
• Can ihs (-)
• Circuit board
• Computer data lines system
• D264
• D265
• Driver door handle lamp
• Driver door module
• Driver side pocket map lamp
• Drv dr hndl lmp
• Drv dr hndl lmp rtn
• Electronic overhead module
• Ft hdr crtsy fd
• Fuse j4 25a
• Fuse j5 25a
• Fuse m34 10a
• G919a (base of right "c" pillar)
• G923a (left "d" pillar)
• G924a (right "d" pillar)
• Gnd
• Hot at all times
• Ign r
• Iod fd
• Left cargo lamp
• Left front grab handle lamp
• Left vanity lamp
• M24
• M27
• M45
• M451
• M46
• M461
• Nca
• Pass dr hndl lamp
• Pass dr hndl lamp rtn
• Pass dr hndl lmp
• Pass dr hndl lmp rtn
• Passenger door handle lamp
• Passenger door module
• Passenger side pocket map lamp
• Rail lamp fds
• Rail lmp fds
• Rechargeable cargo lamp
• Right cargo lamp
• Right front grab handle lamp
• Right vanity lamp
• Run relay (on pcb)
• S335
• S337
• S350
• S367
• S506
• S507
• S600
• S606
• S607
• S903
• S904
• S905
• Tiow park
• Totally integrated power module (left side of engine compt)
• Z917
• Z919
• Z924

Instrument Illumination Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Instrument Illumination Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• A909
• B (+)
• Batt fd
• C202
• C266
• C267
• C321
• Can c (+)
• Can c (-)
• Can ihs (+)
• Can ihs (-)
• Circuit board
• Cluster
• Computer data lines system
• Cupholder lamp
• D264
• D265
• D51
• D52
• Dim 3 ip
• Dimm sig sel
• E12
• E34
• Electronic overhead module
• Fuse m13 20a
• Fuse m15 20a
• Fuse m20 15a
• G911a (left side of dash)
• G912a (under front of center console)
• G923a (left "d" pillar)
• G924a (right "d" pillar)
• Gnd
• Hdlp/fog lmp sel sw
• Hdlp/fog lmp sw
• Headlamp switch
• Hot at all times
• Hot w/ run/start relay energized
• Ign rs
• Iod fd
• Left rear heated seat switch
• Mlfnct sw rtn
• Nca
• Pass sw ill ft
• Passenger door module
• Passenger window/ door lock switch
• Prndl lamp
• Red
• Right rear heated seat switch
• S231
• S245
• S246
• S327
• S330
• S339
• S340
• S343
• Steering control module (steering column)
• Totally integrated power module (left side of engine compt)
• Z912
• Z924

MEMORY SYSTEMS

Memory Systems Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Memory Systems Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• (base of left "c" pillar) g916a
• 25a
• A210
• Adj ped rtn
• Aft mux-lt pwr sts bse fore
• C201
• C302
• C334
• C663
• Can ihs (+)
• Can ihs (-)
• Computer data lines system
• D264
• D265
• Driver door module
• Driver front vertical seat adjuster motor
• Driver horizontal seat adjuster motor
• Driver rear vertical seat adjuster motor
• Driver recliner seat adjuster motor
• Driver seat switch
• Drv mem sts ft vert dn
• Drv mem sts horz aft
• Drv mem sts horz fwd
• Drv mem sts rclne aft
• Drv mem sts rclne fwd
• Drv mem sts rr vert dn
• Drv mem sts rr vert up
• Drv mem sts vert mtr fwd
• Ft batt fd
• G200
• G401
• G402
• G403
• G404
• G491
• G492
• G493
• G494
• G914
• G920
• Gnd
• Hall snsr ft rsr gnd
• Hall snsr ft rsr-pwr
• Hall snsr horz gnd
• Hall snsr horz pwr
• Hall snsr rclnr gnd
• Hall snsr rclnr pwr
• Hall snsr rr rsr gnd
• Hall snsr rr rsr pwr
• Horz aft drv mem sts
• Hot at all times
• Mem sel mux
• Mem sel snse rtn
• Mem sts snse fd
• Mem sts snse rtn
• Memory seat module (under driver seat)
• Memory set switch
• Mtr fwd drv mem sts vert
• P111
• P113
• P115
• P117
• P119
• P121
• P141
• P143
• P151
• P152
• P153
• P157
• P28
• P29
• P309
• P311
• P953
• Power seat circuit breaker
• Pwd drv mem sts horz
• Pwr sts bse fore/aft mux-lt
• Pwr sts rclne mux-lt
• S247
• S250 (right side of engine, in powertrain battery harness)
• S406
• S408
• Steering telescope motor (under left side of dash)
• Steering tilt motor (under left side of dash)
• Strg hall snsr pwr fore/aft
• Strg hall snsr pwr up/dn
• Strg mtr fore/aft
• Strg mtr up/dn
• Strg mtr up/dn rtn
• Vert dn drv mem sts ft
• Vert dn drv mem sts rr
• Vert up drv mem sts rr
• Z916

NAVIGATION

Blind Spot Monitoring Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Blind Spot Monitoring Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• Blind spot module (under driver's seat)
• C389
• Can bus (+) blind
• Can bus (-) blind
• Can ihs (+)
• Can ihs (-)
• Computer data lines system
• D264
• D265
• D764
• D765
• F921
• Fuse m34 10a
• G916a (base of left "c" pillar)
• Gnd
• Hot w/ run relay (on pcb) energized
• Ignr
• Left rear blind spot sensor
• Nca
• Right rear blind spot sensor
• S347
• S348
• S350
• S393
• S394
• Totally integrated power module (left side of engine compt)
• Z916

Parking Assistant Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Parking Assistant Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• (left rear of top of engine, in injector harness)
• 8 dtlnk rtn
• C139
• C140
• C315
• C389
• Can ihs (+)
• Can ihs (-)
• Computer data lines system
• D264
• D265
• D701
• D702
• D703
• D704
• D705
• D706
• D707
• D708
• D709
• D710
• Dtlnk rtn
• F921
• Fuse m34 10a
• G924a (right "d" pillar)
• Ground
• Hot w/ run relay (on pcb) energized
• Ign r
• Nca
• Park assist module (right "d" pillar)
• Park assist sensor 1 (if equipped)
• Park assist sensor 10
• Park assist sensor 11
• Park assist sensor 2 (if equipped)
• Park assist sensor 3 (if equipped)
• Park assist sensor 4 (if equipped)
• Park assist sensor 5 (if equipped)
• Park assist sensor 6 (if equipped)
• Park assist sensor 8
• Park assist sensor 9
• Pnk/red
• S263
• S311
• S344
• S350
• S379
• Snsr 1 dt lnk rtn ft
• Snsr 10 dtlnk rtn rr
• Snsr 11 dtlnk rtn rr
• Snsr 2 dt lnk rtn ft
• Snsr 3 dt lnk rtn ft
• Snsr 4 dt lnk rtn ft
• Snsr 5 dt lnk rtn ft
• Snsr 6 dt lnk rtn ft
• Snsr 8 dtlnk rtn rr
• Snsr 9 dtlnk rtn rr
• Snsr fd ft
• Snsr fd rr
• Snsr sonic rtn ft
• Snsr sonic rtn rr
• Sonic rtn
• Sonic snsr fd ft
• Sonic snsr fd rr
• Totally integrated power module (left side of engine compt)
• X700
• X702
• X750
• X751
• Z924

Rear Camera Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Rear Camera Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• Anti-theft system
• C201
• C390
• C392
• Camera rtn
• Camera shield
• Camera sig
• Can ihs (+)
• Can ihs (-)
• Circuit board
• Computer data lines system
• D264
• D265
• Exterior lights system
• F921
• Flpr glss rel
• Flpr glss rf2
• Fuse m34 10a
• G924a (right "d" pillar)
• Gnd
• Hot w/ run relay (on pcb) energized
• Ignr
• L78
• Lgate hndl sw rtn
• Lgate hndl sw sig
• License plate lamp/ rear camera assembly (center of tailgate)
• Nca
• Nca camera shld
• P30
• P39
• Q80
• Radio
• Rt ft prk/tl lmps 1
• S259
• S335
• S350
• Totally integrated power module (left side of engine compt)
• X970
• X971
• X972
• Z924

POWER DISTRIBUTION

Power Distribution Wiring Diagram (1 of 4) for Jeep Grand Cherokee Laredo X 2013

List of elements for Power Distribution Wiring Diagram (1 of 4) for Jeep Grand Cherokee Laredo X 2013:

• (in driver seat harness)
• (left side of engine compt) power distribution center
• (not used)
• 20a
• 25a
• 3.6l
• 3.6l & 6.4l
• 5.7l & 6.4l
• 6.4l
• A/c heater module
• Active damping control module (if equipped)
• Air susp- ension relay
• Anti-lock brakes module
• Batt drct to pdc
• Battery
• Brake provision module
• Bus bar
• C161
• C192
• C202
• C267
• C301
• C306
• C316
• C321
• C663
• C664
• Circuit board
• Cluster
• Data link connector
• Driver door module
• Driver lumbar seat adjuster switch
• Driver seat switch (w/o memory)
• Electronic limited slip differential module (6.4l)
• Electronic limited slip differential module (if equipped)
• Electronic overhead module
• Except 6.4l
• Fuse 1 30a
• Fuse 2 60a
• Fuse 3 100a
• Fuse 4 100a
• Fuse 5 150a
• Fuse block
• Fuse holder
• Fuse j1 40a
• Fuse j13 60a
• Fuse j2 30a
• Fuse j3 40a
• Fuse j4 25a
• Fuse j5 25a
• Fuse j6 40a
• Fuse j7 30a
• Fuse j8 40a
• Fuse j9 30a
• Fuse m10 15a
• Fuse m13 20a
• Fuse m2 20a
• Fuse m30 15a
• Generator
• Ign unlk/ run/start
• Iod fd
• Memory seat module
• Nca
• Nca fuse m11 10a
• Nca fuse m12 30a
• Passenger
• Passenger door module
• Passenger lumbar seat adjuster switch
• Power liftgate module
• Power seat circuit breaker
• Power steering pump motor
• Powertrain control module (if equipped)
• Radiator cooling fan module (if equipped)
• Radio
• Radio amplifier
• Red
• Red (or tan)
• S147 (except 6.4l) s163 (6.4l)
• S149
• S150
• S151 (except 6.4l)
• S155 (except 6.4l)
• S293
• S294
• S323
• S324
• S325 red
• S327
• S328
• S406 (passenger) harness)
• S831
• Seat switch
• Shift lever assembly
• Starter
• Tan
• Tan (or red)
• Tan/red
• Totally integrated power module (left side of engine compt)
• Trailer tow 7-way wiring
• Vacuum pump fuse holder
• Vacuum pump relay
• W/ rear differential

Power Distribution Wiring Diagram (2 of 4) for Jeep Grand Cherokee Laredo X 2013

List of elements for Power Distribution Wiring Diagram (2 of 4) for Jeep Grand Cherokee Laredo X 2013:

• (base of right "c" pillar) g919a
• (left side of engine compt) totally integrated power module
• 110v ac line 1
• 110v ac line 2
• A/c power outlet
• A904
• Ant sig
• Ant uhf
• Ant uhf ant sig
• Auto shut down relay
• Backup lmp sw
• Batt fd
• Batt fd4
• Batt feed
• Blower motor relay
• Bus bar
• C202
• C204
• C266
• C267
• C300
• C664
• Can c (+)
• Can c (-)
• Can ihs (+)
• Can ihs (-)
• Circuit board
• Cluster
• Computer data lines system
• Door lock relay
• Driver door unlock relay
• Driver window/door lock switch
• Enable sw sig
• From run/ start relay (diagram 3 of 4)
• From totally integrated power module (diagram 3 of 4)
• Front washer pump relay
• Fuel door switch
• Fuse j19 60a
• Fuse j20 25a
• Fuse j21 20a
• Fuse m1 15a
• Fuse m20 15a
• Fuse m26 10a
• Fuse m27 10a
• Fuse m29 10a
• Fuse m31 20a
• Fuse m38 25a
• Fuse m5 25a
• G912a (under front of center console)
• Gnd
• Horn relay
• Ign run st
• Ignition wireless node
• Inv stat ind
• Inverter module (under front passenger seat)
• Lin tire press
• Nca
• P801
• P802
• P806
• P807
• Park lamp relay
• Passenger door unlock relay
• Passive entry module
• Radiator fan high relay (3.6l)
• Radiator fan low relay
• Rain sensor
• Rear washer pump relay
• Rear wiper relay
• Red
• Remote start antenna
• S230
• S231
• S326
• S388
• S418
• Shift lever assembly
• Sol unlk
• Steering control module
• Stop lamp switch
• Stp lmp sig
• Sw sig
• Tan/red
• Tire pressure module
• Totally integrated power module (left side of engine compt)
• Trans rng sig
• Transfer case selector
• Transmission control relay
• Upper bank switch
• Wiper high/ low relay
• Wiper on/off relay
• Z919

Power Distribution Wiring Diagram (3 of 4) for Jeep Grand Cherokee Laredo X 2013

List of elements for Power Distribution Wiring Diagram (3 of 4) for Jeep Grand Cherokee Laredo X 2013:

• (left side of engine compt) totally integrated power module
• (not used)
• 25a
• 3.6l & 5.7l
• 6.4l
• Acc dly rly ctrl
• Active damping controller module (if equipped)
• Adaptive cruise control module
• Anti-lock brakes module
• Batt feed
• Batt pre
• Batt pre1
• Bus bar
• C137
• C139
• C161
• C202
• C204
• C301
• C311
• C315
• C321
• Cigar lighter
• Circuit board
• Circuit breaker
• Cluster
• Driver door/ window lock switch
• Drivetrain control module (6.4l)
• Drivetrain control module (if equippd)
• Electronic limited slip differential module (6.4l & 5.7l)
• Except 5.7l
• Except 6.4l
• Fuel pump relay
• Fuse holder m7
• Fuse j10 30a
• Fuse j11 30a
• Fuse j22 25a
• Fuse m15 20a
• Fuse m16 10a
• Fuse m28 15a
• Fuse m3 20a
• Fuse m33 10a
• Fuse m37 10a
• Fuse m6 20a
• Fuse m7 20a
• G911a (left side of dash)
• G924a
• Headlamp washer relay
• Ign run acc
• Ign run st
• Inside rearview mirror
• Left drl relay
• Left drl relay (except 6.4l)
• Liftgate unlock relay
• Nca
• Occupant restraint controller module
• Power distribution center (left side of engine compt)
• Power steering pump motor (if equippd)
• Powertrain control module
• Radiator fan high relay
• Rain sensor
• Rear power outlet
• Rear window defogger relay
• Red
• Red s381
• Right drl relay
• Right drl relay (except 6.4l)
• Run strt ctrl
• Run/ accessory delay relay
• Run/ accessory relay
• Run/ start relay
• S110
• S246
• S302
• S332
• S352
• S353 (body harness)
• S353 (headlamp & dash harness)
• S354
• Stop lamp switch
• Sunroof motor
• Sunroof shade motor
• To ignition wireless node (diagram 2 of 4)
• To wiper on/off relay (diagram 2 of 4)
• Transmission control module (except 5.7l)
• Vacuum pump relay (3.6l)

Power Distribution Wiring Diagram (4 of 4) for Jeep Grand Cherokee Laredo X 2013

List of elements for Power Distribution Wiring Diagram (4 of 4) for Jeep Grand Cherokee Laredo X 2013:

• (in rear console) s339
• (not used)
• A/c heater control
• Batt pre
• Batt pre 3
• Blind spot module
• Bus bar
• C139
• C202
• C205
• C266
• C267
• C315
• C321
• C389
• C392
• C665
• Circuit board
• Compass module
• Console power outlet
• Fuse m14 20a
• Fuse m32 10a
• Fuse m34 10a
• Fuse m36 20a
• Fuse m8 20a
• Fuse m9 20a
• G911a (left side of dash)
• Heated seats module
• Left drl lamp (6.4l)
• Left front lamp assembly
• Left rear blind spot sensor
• Left rear heated seat switch
• Nca
• Occupant restraint controller module
• Park assist module
• Pnk/tan
• Rear camera/ license plate lamp assembly
• Rear wiper relay
• Rechargeable cargo lamp
• Right drl lamp (6.4l)
• Right front lamp assembly
• Right rear blind spot sensor
• Right rear heated seat switch
• Run ctrl
• Run relay
• Run relay (on pcb)
• S129
• S258
• S339
• S347
• S350
• S391
• S421
• S902
• Starter relay
• Totally integrated power module (left side of engine compt)
• Ttow prk

POWER DOOR LOCKS

Power Door Locks Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for Power Door Locks Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013:

• 87a
• Abmt temp/ fcm ssr rtn 1
• Abmt temp/fcm ssr rtn 1
• Ambient air temperature sensor (left side of front grille)
• C300
• C301
• C305
• C306
• C383
• C384
• C390
• C392
• Can ihs (+)
• Can ihs (-)
• Circuit board
• Computer data lines system
• D264
• D265
• Door lock relay
• Dr ajar lt rr sig
• Dr ajar rt rr sig
• Dr lk lt ft
• Dr lk rt ft
• Dr lock rly ctrl lt
• Dr ulk rt ft
• Driver door latch
• Driver door unlock relay
• Drv ft dr ajar sw in
• Flip-up glass latch
• Flpr mtr rel
• Front washer fluid level sensor (left front of engine compt, in fluid reservoir)
• Ft drv dr lk
• Ft drv dr ulk
• Ft pass dr lk
• Ft pass dr ulk
• Fuse m38 25a
• G306
• G70
• G74
• G75
• G76
• G77
• G78
• G80
• G919a (base of right "c" pillar)
• G923a (left "d" pillar)
• G924a (right "d" pillar)
• G931
• Gnd
• Hot at all times
• Left rear door latch
• Lgate ajar sig
• Lt rr dr ajar sig
• Lt rr lk
• Lt rr ulk
• Nca
• P920
• P930
• P940
• Pass ft & rr & drv rr ulk
• Pass ft dr ajar sw in
• Passenger door latch
• Passenger door unlock relay
• Q81
• Right rear door latch
• Rr glass ajar sig
• Rr glss ajar sig
• Rt rr dr ajar sig
• Rt rr lk
• Rt rr ulk
• S134
• S335
• S501
• S600
• S700
• S800
• Totally integrated power module (left side of engine compt)
• Uhood sw sig

Power Door Locks Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for Power Door Locks Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013:

• (not used) c316
• 100 fd to dr node-drv
• A214
• A215
• Abmt temp/ fcm ssr rtn 1
• Batt fd
• C300
• C301
• C306
• C383
• C384
• C392
• Can ihs (+)
• Can ihs (-)
• Can ihs +
• Can ihs -
• Computer data lines system
• D264
• D265
• D501
• D903
• Driver door module
• Driver window/ door lock switch
• E34
• Eatx batt fd
• Ft pass dr lk sw sig
• Ft pass sw illm/sns rtn
• Ft pass up sw snse
• Fuse j4 25a
• Fuse j5 25a
• Fuse m26 10a
• Fuse m3 20a
• G160
• G78
• G909a (right rear of engine compt)
• G923a (left "d" pillar)
• Gnd
• Hood ajar switch (above center of radiator grille)
• Hot at all times
• Iod fd to dr node-drv
• L177
• Left rear power window switch
• Lgate ajar sig
• Liftgate door latch
• Liftgate unlock relay
• Lin dcm dr
• Lin slve rtn
• Nca
• Park lamp relay
• Passenger door module
• Passenger window/ door lock switch
• Power distribution center (left side of engine compt)
• Power liftgate module (left "d" pillar)
• Prk lmp rly ctrl
• Q336
• Q936
• Right rear power window switch
• Rr dr ulk rly ctrl
• S302
• S355
• S501
• Sw illm ft pass
• Sw pwr lk out fd rr lt
• Sw pwr lk out fd rr tt
• Totally integrated power module (left side of engine compt)
• Uhood sw sig

POWER MIRRORS

Power Mirrors Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Power Mirrors Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• (under front of center console) g912a
• A214
• A215
• Bkup lmps fd
• C201
• C202
• C204
• C300
• C301
• C305
• C306
• Can ihs (+)
• Can ihs (-)
• Computer data lines system
• D264
• D265
• Driver door module
• Ec mrr rtn
• Exterior lights system
• F943
• Fuse j4 25a
• Fuse j5 25a
• Fuse m15 20a
• G919a (base of right "c" pillar)
• G923a (left "d" pillar)
• Gnd
• Handsfree module (left end of dash)
• Hf mic 2 in+
• Hf mic hsd fd
• Hf mic ref
• Hnds free mic in+
• Hnds free mic in-
• Hot at all times
• Hot w/ run/ start relay energized
• Ign rs
• Inside rearview mirror
• Iod fd to dr node-drv
• Iod fd to dr node-pass
• Out side ec
• Out side ec mrr sig
• Out side ec mrr sig gnd
• P112
• P114
• Passenger door module
• Radio
• S246
• S253
• S254
• S600
• Totally integrated power module (left side of engine compt)
• W/ hands free module
• W/o hands free module
• X712
• X722
• X792
• X793
• X835
• Z912
• Z917
• Z919

POWER SEATS

Driver Power Seat Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Driver Power Seat Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• (not
• 25a
• C334
• Driver horizontal seat adjuster motor
• Driver horizontal varistor
• Driver seat switch
• Front driver varistor
• Front driver vertical seat adjuster motor
• Ft batt fd
• G916a (base of left "c" pillar)
• Gnd
• Hot at all times
• Power seat circuit breaker
• Pwr ft dn drv
• Pwr ft up drv
• Pwr horz fwd drv
• Pwr rclnr mtr aft
• Pwr rclnr mtr fwd
• Pwr sts horz aft
• Pwr vert rr dn drv
• Pwr vert rr up drv
• Rear driver varistor
• Rear driver vertical seat adjuster motor
• S400
• S401
• S402
• S403
• S404
• S405
• S406
• S408
• Used)

Heated Seats Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for Heated Seats Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013:

• Batt fd 9
• C266
• C664
• C665
• C91
• C986
• Can ihs (+)
• Can ihs (-)
• Computer data lines system
• Cshn bk vent mtr fd ft lt
• Cshn bk vent mtr fd ft rt
• D264
• D265
• Dim sip
• F930
• F931
• Ft lt cshn bk vent mtr rtn
• Ft rt cshn bk vent mtr rtn
• Fuse m08 20a
• Fuse m09 20a
• Fuse m20 15a
• Fuse m34 10a
• G912a (under front of center console)
• G919a (base of right "c" pillar)
• G923a (left "d" pillar)
• Gnd
• Ground
• Heat out to coil ft lt
• Heat out to coil ft rt
• Heat out to coil rr lt
• Heat out to coil rr rt
• Heatd sts snsr rtn
• Heated seats module (under front passenger seat)
• Hi ind lt lr htd sts
• Hot at all times
• Hot w/ run (on pcb) relay energized
• Hot w/ run relay energized
• Htd str whl fd
• Ign r
• Interior lights system
• Left rear heated seat switch
• Lin ccn
• Lo ind rt rr htd sts
• Lr htd sts hi ind lt
• Lr htd sts lo ind lt
• Lr htd sts sw pos snse lt
• Lt ft heatd sts temp snsr
• Lt rr heatd sts temp snsr
• Nca
• P165
• P166
• P177
• P178
• P181
• P182
• P183
• P184
• P187
• P188
• P421
• P422
• P672
• P673
• P687
• P688
• P921
• P922
• P968
• Red
• Right rear heated seat switch
• Rr htd sts hi ind rt
• Rr htd sts lo ind rt
• Rr htd sts sw pos snse rt
• Rt ft heatd stst temp snsr
• Rt rr heatd stst temp snsr
• S231
• S339
• S340
• S418
• S421
• Strg whl htr rtn
• Sw pos snse lt lr htd sts
• Totally integrated power module (left side of engine compt)
• Upper bank switch
• Z919

Heated Seats Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for Heated Seats Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013:

• C202
• C333
• C334
• C663
• C665
• C91
• C986
• G916a (base of left "c" pillar)
• G919a (base of right "c" pillar)
• Gnd
• Heat out to coil ft lt
• Heat out to coil ft rt
• Heat out to coil rr lt
• Heat out to coil rr rt
• Heatd sts snsr rtn
• Htd str whl fd
• Left fr seat back vent
• Left fr seat cushion heater
• Left front seat cushion heater
• Left rear seat cushion heater
• Lt ft heatd sts temp snsr
• Lt rr heatd sts temp snsr
• Right fr seat back vent
• Right fr seat cushion heater
• Right front seat cushion heater
• Right rear seat cushion heater
• Rt ft heatd sts temp snsr
• Rt rr heatd sts temp snsr
• S371
• S407
• S408
• S409
• S417
• S419
• S420
• S422 (under front passenger seat, in seat passenger harness)
• Steering control module (steering column)
• Strg whl htr rtn

Heated Steering Wheel Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Heated Steering Wheel Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• C202
• C665
• C91
• C986
• Can ihs (+)
• Can ihs (-)
• Computer data lines system
• D264
• D265
• D507
• Evic/nav rmux rtn
• F931
• Fuse m9 20a
• G919a (base of right "c" pillar)
• Gnd
• Heated seats module (under front passenger seat)
• Hot w/ run relay energized
• Htd str whl fd
• Htd str whl sig
• Ign r
• Left steering wheel switch
• Lin sccm
• Nca
• S270 (left front of engine, in multiple displacement solenoid harness)
• S418
• S421
• Speed control switch
• Steering control module (steering column)
• Steering wheel heater sensor
• Strg whl htr rtn
• Totally integrated power module (left side of engine compt)
• Z919

Lumbar Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Lumbar Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• (base of left "c" pillar) g916a
• 25a
• B deflate/ rearward
• B inflate/ forward
• C deflate/ rearward
• C inflate/ forward
• C333
• C334
• Driver forward/ rearward seat lumbar switch
• Driver lumbar seat adjuster switch
• Driver up/down seat lumbar motor
• Front passenger forward/rearward seat lumbar motor
• Front passenger up/down seat lumbar motor
• Ft batt fd
• G919a (base of right "c" pillar)
• Gnd
• Hot at all times
• Lmbr down driv
• Lmbr down pass
• Lmbr up driv
• Lmbr up pass
• Passenger lumbar seat adjuster switch
• Power seat circuit breaker
• Rear passenger forward/rearward seat lumbar motor
• Rear passenger up/down seat lumbar motor
• S406
• S408
• S418

Passenger Seat Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Passenger Seat Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• (not used)
• 25a
• C333
• Front passenger varistor
• Front passenger vertical seat adjuster motor
• Ft batt fd
• G919a (base of right "c" pillar)
• Gnd
• Hot at all times
• Passenger horizontal seat adjuster motor
• Passenger horizontal varistor
• Passenger seat recliner adjuster motor
• Passenger seat switch
• Power seat circuit breaker
• Pwr ft dn pass
• Pwr ft up pass
• Pwr horz fwd pass
• Pwr horz rwd pass
• Pwr rclnr dn pass
• Pwr rclnr up pass
• Pwr vert rr dn pass
• Pwr vert rr up pass
• Rear passenger varistor
• Rear passenger vertical seat adjuster motor
• S406
• S410
• S411
• S412
• S413
• S414
• S415
• S418

POWER TOP/SUNROOF

Power Top/Sunroof Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Power Top/Sunroof Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• (not used)
• A940
• Batt fd 6
• C311
• Circuit board
• D270
• Electronic overhead module
• F981
• Fuse j22 25a
• G924a (right "d" pillar)
• Gnd
• Hot at all times
• Ign run acc
• Nca
• Q556
• Q56
• Red
• S321
• S354
• S381
• S382
• S383
• S384
• S905
• Shade close(+)
• Shade open(+)
• Sunrf dgnstc line
• Sunrf pwr cls(+)
• Sunrf pwr opn(+)
• Sunrf swd rtn
• Sunrf vent(+)
• Sunroof motor
• Sunroof shade motor
• Totally integrated power module (left side of engine compt)
• Z911
• Z923

POWER WINDOWS

Power Windows Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Power Windows Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• (base of right "c" pillar) g919a
• (left "d" pillar) g923a
• A214
• A215
• C300
• C301
• C306
• C383
• C384
• Can ihs (+)
• Can ihs (-)
• Circuit breaker 1
• Computer data lines system
• D264
• D265
• D501
• D903
• Driver door module
• Driver window motor
• Driver window/door lock switch
• E34
• Fd drv hall snsr fd
• Ft driv wdo snsr rtn
• Ft drv hall snsr a
• Ft drv hall snsr fd
• Ft pass dr lk sw sig
• Ft pass hall snsr a
• Ft pass hall snsr fd
• Ft pass sw illm/sns rtn
• Ft pass up sw snse
• Ft pass wdo snsr rtn
• Fuse j04 25a
• Fuse j05 25a
• Fuse m26 10a
• G160
• G919a (base of right "c" pillar)
• G923a (left "d" pillar)
• Gnd
• Hot at all times
• Hot w/ run accessory relay energized
• Iod fd to dr node-drv
• Iod fd to dr node-pass
• Left rear power window switch
• Left rear window motor
• Lin dcm rtn
• Lin slve rtn
• Mstr ctrl rr dn lt
• Mstr ctrl rr dn rt
• Mstr ctrl rr up lt
• Mstr ctrl rr up rt
• N/a
• Nca
• Passenger door module
• Passenger window motor
• Passenger window/door lock switch
• Q11
• Q12
• Q21
• Q22
• Q301
• Q302
• Q305
• Q306
• Q336
• Q936
• Q990
• Q991
• Right rear power window switch
• Right rear window motor
• S501
• S600
• S700
• S800
• Sw 5v pwr mrr batt fd
• Sw illm ft pass
• Sw pwr wdw lk out fd rr lt
• Sw pwr wdw lk out fd rr rt
• Totally integrated power module (left side of engine compt)
• Wdo dwn ft driv
• Wdo dwn ft pass
• Wdo dwn rr lt
• Wdo dwn rr rt
• Wdo up ft driv
• Wdo up ft pass
• Wdo up rr lt
• Wdo up rr rt
• Wdw run/accy ign
• Z917
• Z919

RADIO

Hands Free Module Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Hands Free Module Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• A413
• C202
• C204
• Can ihs (+)
• Can ihs (-)
• Computer data lines system
• D264
• D265
• Fuse m10 15a nca
• G912a (under front of center console)
• Gnd
• Hands free module (left end of dash)
• Hf audo out com
• Hf audo output com
• Hf mic 2 in +
• Hf mic hsd fd
• Hf mic ref
• Hnds free mic in +
• Hnds free mic in -
• Hot at all times
• Inside rearview mirror
• Iod fd
• Left hf audio out
• Left hf audo output
• Nca
• Radio
• Right hf audio out
• Right hf audo output
• S328
• Totally integrated power module (left side of engine compt)
• X703
• X704
• X712
• X722
• X792
• X793
• X795
• X835
• Z912

Radio Wiring Diagram (1 of 3) for Jeep Grand Cherokee Laredo X 2013

List of elements for Radio Wiring Diagram (1 of 3) for Jeep Grand Cherokee Laredo X 2013:

• (center of rear headliner) radio antenna
• (pins: 3 to 6 not used)
• A116
• A413
• Am/fm coax
• Am/fm coax shld
• Aud comp fd
• Aud left 1
• Aud left 2
• Aud left 3
• Aud right 1
• Aud right 2
• Aud right 3
• Aud rtn 1
• Aud rtn 2
• Aud rtn 3
• Audio left 1
• Audio left 2
• Audio left 3
• Audio return 1
• Audio return 2
• Audio return 3
• Audio right 1
• Audio right 2
• Audio right 3
• Aux aud comp fd
• C201
• C202
• C204
• C205
• C206
• C208
• C320
• C390
• Camera
• Camera return
• Camera shld
• Camera sig
• Can ihs (+)
• Can ihs (-)
• Can ihs bus (+)
• Can ihs bus (-)
• Computer data lines system
• D106
• D126
• D264
• D265
• D931
• Fuse m10 15a
• Fuse m12 30a
• G912a (under front of center console)
• G923a (left "d" pillar)
• Gnd
• Hands free module (left end of dash)
• Hf aud o/p com
• Hf aud o/p lt
• Hf aud o/p rt
• Hf mic 2 in +
• Hf mic hsd fd
• Hf mic in +
• Hf mic ref
• Hnds free mic in +
• Hnds free mic in -
• Hot at all times
• I550
• Inside rearview mirror
• Iod fd
• License plate lamp/ rear camera assembly (center of tailgate)
• Nca
• Rad lt rr (+)
• Rad lt rr (-)
• Rad rt rr (+)
• Rad rt rr (-)
• Radio
• Red
• Return
• S259
• S323
• S910 (headliner harness)
• S912
• S913
• Satellite radio antenna
• Sdar coax sat shld
• Sdar coax sat sig
• Shield
• Shld
• Sig
• Sx536-dv
• Sx543-dv
• Totally integrated power module (left side of engine compt)
• Vcom 1
• Vcom 2
• Vcommon 1
• Vcommon 2
• Video screen module (if equipped) (in rear overhead console)
• Visg 1
• Vshield 1
• Vshield 2
• Vshld 1
• Vshld 2
• Vsig 1
• Vsig 2
• W/ hands free module
• W/ satellite radio antenna
• W/o hands free module
• W/o satellite radio antenna
• X51
• X52
• X534
• X535
• X536
• X538
• X539
• X540
• X541
• X542
• X543
• X544
• X545
• X546
• X550
• X551
• X552
• X57
• X58
• X62
• X703
• X703 (or x722)
• X704
• X704 (or x712)
• X792
• X793
• X795
• X835
• X970
• X971
• X972
• Z912
• Z921

Radio Wiring Diagram (2 of 3) for Jeep Grand Cherokee Laredo X 2013

List of elements for Radio Wiring Diagram (2 of 3) for Jeep Grand Cherokee Laredo X 2013:

• C304
• C383
• Can c (+)
• Can c (-)
• Computer data lines system
• D507
• D51
• D52
• Dr spkr +
• Dr spkr -
• Fd (+) lt
• Ft i/p spkr
• Ft lt ip
• Horn switch
• Left d-pillar speaker
• Left front door speaker
• Left front door tweeter speaker
• Left rear door speaker
• Left rear tweeter speaker
• Left remote radio/ peddle switch
• Lin sccm
• Red
• Rem rad ctrl sw sig
• Rem rad sw snse rtn
• Right d-pillar speaker
• Right remote radio/ peddle switch
• Rr lt
• Rr lt dr spkr -
• Rr lt shlf
• Rr rt shlf spkr rtn -
• Rr shlf
• Rr shlf spkr fd + lt
• S271
• S272
• S273
• S274
• S503 (top right side of liftgate, in liftgate harness)
• S505
• S701
• S702
• Speed control switch
• Spkr fd + rt
• Spkr rtn
• Spkr rtn -
• Steering control module (steering column)
• Trx

Radio Wiring Diagram (3 of 3) for Jeep Grand Cherokee Laredo X 2013

List of elements for Radio Wiring Diagram (3 of 3) for Jeep Grand Cherokee Laredo X 2013:

• (not used)
• (pins: 9 to 15 not used)
• (top center side of liftgate, in liftgate harness) s502
• 1 input (+)
• 1 rtn (-)
• 2 input (+)
• 2 rtn (-)
• A116
• Aud aux rtn 2
• Aud sig com
• Aux audio lh sig 2
• Aux audio rh sig 2
• Aux audio rtn 2
• Auxiliary audio video port
• C201
• C266
• C301
• C306
• C309
• C320
• C384
• Can ihs (+)
• Can ihs (-)
• Center instrument panel speaker
• Computer data lines system
• Ctr ip spkr input (+)
• Ctr ip spkr rtn (-)
• D264
• D265
• Dr spkr +
• Dr spkr -
• Fd (+) lt
• Fr rt dr
• Fr rt dr spkr 1 (+)
• Ft i/p spkr fd (+) lt
• Ft ip spkr fd (+) lt
• Ft ip spkr fd (+) rt
• Ft lt dr spkr 1 (+)
• Ft lt dr spkr 1 (-)
• Ft lt ip
• Ft lt ip spkr rtn (-)
• Ft rt dr spkr 1 (+)
• Ft rt dr spkr 1 (-)
• Ft rt ip spkr rtn (-)
• G923a (left "d" pillar)
• Gnd
• Input (+)
• Iod fd
• Left aud sig +
• Left aux aud 2
• Left front door speaker
• Left rr shlf spkr fd (+)
• Nca
• Rad lt rr (+)
• Rad lt rr (-)
• Rad rt rr (+)
• Rad rt rr (-)
• Radio amplifier (left rear cargo compartment floor)
• Right aud sig +
• Right aux aud 2
• Right front door speaker
• Right front door tweeter speaker
• Right rear door speaker
• Right rear door tweeter speaker
• Rr lt dr spkr (+)
• Rr lt dr spkr (-)
• Rr lt shlf spkr rtn (-)
• Rr rt dr spkr (+)
• Rr rt dr spkr (-)
• Rr rt shlf spkr rtn -
• Rr shlf spkr fd + rt
• S504 (top right side of liftgate, in liftgate harness)
• S801
• S802
• S911
• Sdars vid sig
• Sdars vid sig com
• Spkr (-)
• Spkr 1 (-)
• Spkr rtn
• Subwoof 1 input +
• Subwoof 1 rtn -
• Subwoof 2 rtn -
• Subwoofer
• Subwoofer 2 input (+)
• Subwoofer speaker
• Sx533-dv
• V aux com2
• V aux sig2
• Vaux com2
• Vaux sig 2
• Video screen module (if equipped) (in rear overhead console)
• Vshield aux2
• Vshld aux2
• X18
• X19
• X200
• X201
• X202
• X205
• X206
• X208
• X209
• X290
• X291
• X292
• X295
• X296
• X298
• X299
• X300
• X301
• X303
• X304
• X391
• X393
• X394
• X51
• X519
• X52
• X521
• X522
• X531
• X532
• X533
• X57
• X58
• X918
• X973
• X974
• Z923

SHIFT INTERLOCK

Shift Interlock Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Shift Interlock Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• (3.6l) s101
• (5.7l & 6.4l) s113
• 5.7l
• 5.7l & 3.6l
• 6.4l
• Astk up
• B15
• B16
• Brk actv snse sig
• Brk actv snse sig2
• Btsi sol ulk
• C161
• C192
• C267
• C315
• Can c (+)
• Can c (-)
• Circuit board
• Cluster
• Computer data lines system
• D51
• D52
• D64
• D65
• Electrohydraulic control unit assembly
• Eng ctrl com snsr rtn
• Fuse m37 10a
• G911a (left side of dash)
• G923a (left "d" pillar)
• Gnd
• Hot w/ run/start relay energized
• Ign rs
• Ign ulk run/ strt
• Ign ulk/run/strt
• K321
• K900
• Left remote radio/ paddle switch
• Lin sccm
• Nca
• Pnk/ f1
• Powertrain control module (right front of engine compt)
• Red
• Right remote radio/ paddle switch
• S271
• S273
• S274
• S331
• S339
• S352
• Shift lever assembly
• Snsr sig trans rng temp
• Spd snse rtn
• Speed control switch
• Stop lamp switch (on brake pedal assembly)
• Sw sig
• T13
• T41
• T42
• T54
• T824
• Totally integrated power module (left side of engine compt)
• Trans rng park
• Trans rng prk/neur sig
• Trans rng temp snsr sig
• Transmission control module (3.6l & 6.4l) (left side of dash)
• Transmission solenoid/trs assembly (5.7l)
• Trs t1
• Trs t3
• Trs t4
• Trs t42
• Trx
• Wireless ignition node
• Z911

STARTING/CHARGING

3.6L

3.6L, Charging Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for 3.6L, Charging Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• A803
• Altr sense
• Battery
• Can c (+)
• Can c (-)
• Can ihs (+)
• Can ihs (-)
• Cluster
• Computer data lines system
• D64
• D65
• Fuse block
• Generator
• Gnrtr source fd
• K125
• Powertrain control module (right front of engine compt)
• Red
• S147
• S151
• S155
• Starting circuit

3.6L, Starting Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for 3.6L, Starting Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• 5.7l & 3.6l
• 6.4l
• 87a
• Ant vhf ant sig
• B(+)
• Batt feed
• Battery
• Btsi sol ulk
• Bus bar
• C130
• C161
• C202
• C204
• C267
• Can c (+)
• Can c (-)
• Charging circuit
• Circuit board
• Computer data lines system
• D51
• D52
• D64
• D65
• Electro hydraulic control unit assembly
• Except 6.4l
• F20
• Fuse block
• Fuse j17 40a
• Fuse m27 10a
• G912a (under front of center console)
• Gnd
• Hold-in
• Hot at all times
• Ign run st
• Ign sw fd
• Integrated power module (left side of engine compt)
• L51
• Lin tire press
• Nca
• Powertrain control module (right front of engine compt)
• Pull-in
• Rain sensor (forward of interior rearview mirror)
• Red
• Remote start antenna
• S149
• S150
• S163 (6.4l) s147 (except 6.4l)
• S230
• S388
• Shift lever assembly
• Smrt strtr rly coil
• Starter
• Starter relay
• Stop lamp switch (on brake pedal assembly)
• Stp lmp sig
• Strtr ovrde rly coil rtn
• T54
• T752
• Tan
• Trans rig park
• Trans ring temp snsr sig
• Transmission control module (left side of dash)
• Wireless ignition node

5.7L

5.7L, Charging Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for 5.7L, Charging Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• A803
• Altr sense
• Battery
• Can c (+)
• Can c (-)
• Can ihs (+)
• Can ihs (-)
• Cluster
• Computer data lines system
• D64
• D65
• Fuse block
• Generator
• Gnrtr source fd
• K125
• Powertrain control module (right front of engine compt)
• Red
• S147
• S151
• S155
• Starting circuit

5.7L, Starting Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for 5.7L, Starting Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• 5.7l & 3.6l
• 6.4l
• 87a
• Ant vhf ant sig
• B(+)
• Batt feed
• Battery
• Btsi sol ulk
• Bus bar
• C130
• C161
• C202
• C204
• C267
• Can c (+)
• Can c (-)
• Charging circuit
• Circuit board
• Computer data lines system
• D51
• D52
• D64
• D65
• Electro hydraulic control unit assembly
• Except 6.4l
• F20
• Fuse block
• Fuse j17 40a
• Fuse m27 10a
• G912a (under front of center console)
• Gnd
• Hold-in
• Hot at all times
• Ign run st
• Ign sw fd
• Integrated power module (left side of engine compt)
• L51
• Lin tire press
• Nca
• Powertrain control module (right front of engine compt)
• Pull-in
• Rain sensor (forward of interior rearview mirror)
• Red
• Remote start antenna
• S149
• S150
• S163 (6.4l) s147 (except 6.4l)
• S230
• S388
• Shift lever assembly
• Smrt strtr rly coil
• Starter
• Starter relay
• Stop lamp switch (on brake pedal assembly)
• Stp lmp sig
• Strtr ovrde rly coil rtn
• T54
• T752
• Tan
• Trans rig park
• Trans ring temp snsr sig
• Transmission control module (left side of dash)
• Wireless ignition node

6.4L

6.4L, Charging Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for 6.4L, Charging Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• A804
• Altr fld fd
• Altr sense
• Battery
• Can c (+)
• Can c (-)
• Can ihs (+)
• Can ihs (-)
• Cluster
• Computer data lines system
• D64
• D65
• Fuse block
• Generator
• K20
• Powertrain control module (right front of engine compt)
• Red
• S149
• S150
• S163
• Starting circuit
• Tan

6.4L, Starting Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for 6.4L, Starting Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• 5.7l & 3.6l
• 6.4l
• 87a
• Ant vhf ant sig
• B(+)
• Batt feed
• Battery
• Btsi sol ulk
• Bus bar
• C130
• C161
• C202
• C204
• C267
• Can c (+)
• Can c (-)
• Charging circuit
• Circuit board
• Computer data lines system
• D51
• D52
• D64
• D65
• Electro hydraulic control unit assembly
• Except 6.4l
• F20
• Fuse block
• Fuse j17 40a
• Fuse m27 10a
• G912a (under front of center console)
• Gnd
• Hold-in
• Hot at all times
• Ign run st
• Ign sw fd
• Integrated power module (left side of engine compt)
• L51
• Lin tire press
• Nca
• Powertrain control module (right front of engine compt)
• Pull-in
• Rain sensor (forward of interior rearview mirror)
• Red
• Remote start antenna
• S149
• S150
• S163 (6.4l) s147 (except 6.4l)
• S230
• S388
• Shift lever assembly
• Smrt strtr rly coil
• Starter
• Starter relay
• Stop lamp switch (on brake pedal assembly)
• Stp lmp sig
• Strtr ovrde rly coil rtn
• T54
• T752
• Tan
• Trans rig park
• Trans ring temp snsr sig
• Transmission control module (left side of dash)
• Wireless ignition node

SUPPLEMENTAL RESTRAINTS

Supplemental Restraints Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for Supplemental Restraints Wiring Diagram (1 of 2) for Jeep Grand Cherokee Laredo X 2013:

• (base of left "b" pillar) driver seat belt retractor tensioner
• (base of right "b" pillar) passenger seat belt retractor tensioner
• (right "b" pillar) right side impact sensor 1
• (under front passenger seat) occupant detection sensor
• 1row driv sig
• 1row pass sig
• A15
• A16
• A17
• A18
• Abg squib1 driv(+)
• Abg squib1 driv(-)
• Abg squib1 pass(+)
• Abg squib1 pass(-)
• Abg squib2 driv(+)
• Abg squib2 driv(-)
• Abg squib2 pass(+)
• Abg squib2 pass(-)
• Belt sw(+)
• Belt sw(-)
• C138
• C139
• C192
• C201
• C202
• C301
• C305
• C352
• C663
• C664
• Can c (+)
• Can c (-)
• Computer data lines system
• D51
• D52
• Driv pret retrct belt(+)
• Driv pret retrct belt(+) driv pret retrct belt(-)
• Driv pret retrct belt(-)
• Driv rtn pos snsr
• Driv seat
• Driv seat belt sw(+)
• Driv seat belt sw(-)
• Driv vltg pos snsr
• Driver seat belt buckle switch
• Driver seat track position sensor
• F100
• F201
• Fuse m16 10a
• Fuse m32 10a nca
• G913a (under center console)
• G919a (base of right "c" pillar)
• Gnd
• Hot w/ run relay (on pcb) energized
• Hot w/ run/start relay energized
• Ign run
• Left front impact sensor (left front of engine compt)
• Left side impact pressure sensor (driver's door)
• Lt crtn squib1(+)
• Lt crtn squib1(-)
• Lt ft impt
• Lt ft impt snsr (+)
• Lt ft impt snsr (-)
• Lt thorax squib(+)
• Lt thorax squib(-)
• Nca
• Occupant restraint controller module (under center console)
• Orc mod run/strt ign
• Pas pret retrct belt(+)
• Pas pret retrct belt(-)
• Pass belt sw 1r(+)
• Pass belt sw 1r(-)
• Pass occp dctr(+)
• Pass occp dctr(-)
• Pass rtn pos snsr
• Pass seat occp dctr(+)
• Pass seat occp dctr(-)
• Pass vltg pos snsr
• Passenger seat belt buckle switch
• Passenger seat track position sensor
• R13
• R130
• R14
• R140
• R15
• R150
• R16
• R160
• R17
• R18
• R19
• R20
• R261
• R262
• R263
• R264
• R283
• R284
• R42
• R43
• R44
• R45
• R503
• R504
• R505
• R506
• R57
• R58
• R59
• R60
• R61
• R62
• R63
• R64
• R676
• R677
• R79
• R80
• R81
• R82
• Right front headrest solenoid (in right front seat back)
• Right front impact sensor (right front of engine compt)
• Right side impact pressure sensor (front passenger's door)
• Right side impact sensor 2 (right "c" pillar)
• Rt crtn squib1(+)
• Rt crtn squib1(-)
• Rt ft impt
• Rt ft impt snsr (+)
• Rt ft impt snsr (-)
• Rt impt
• Rt impt prss sns1 (+)
• Rt impt prss sns1 (-)
• Rt thorax squib(+)
• Rt thorax squib(-)
• S419
• Sde impt prss
• Sde impt prss snsr1 lt(+)
• Sde impt prss snsr1 lt(-)
• Sde impt snsr1 lt(+)
• Sde impt snsr1 lt(-)
• Sde impt snsr1 rt(+)
• Sde impt snsr1 rt(-)
• Sde impt snsr2 lt(+)
• Sde impt snsr2 lt(-)
• Sde impt snsr2 rt(+)
• Sde impt snsr2 rt(-)
• Sig pass 1row
• Snsr (+)
• Snsr (-)
• Snsr1 lt(+)
• Snsr1 lt(-)
• Snsr1 rt(-) sde impt
• Tan
• Totally integrated power module (left side of engine compt)
• Z913

Supplemental Restraints Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013

List of elements for Supplemental Restraints Wiring Diagram (2 of 2) for Jeep Grand Cherokee Laredo X 2013:

• Abg squib1 driv(+)
• Abg squib1 driv(-)
• Abg squib2 driv(+)
• Abg squib2 driv(-)
• C352
• C353
• C664
• Can c (+)
• Can c (-)
• Can ihs (+)
• Can ihs (-)
• Cluster
• Computer data lines system
• D51
• D52
• Driv sig 1row
• Driv(+) abg squib1
• Driv(+) abg squib2
• Driv(-) abg squib1
• Driv(-) abg squib2
• Driver air bag squib 1 (in steering wheel)
• Driver air bag squib 2 (in steering wheel)
• G916a (base of left "c" pillar)
• Gnd
• Left front headrest solenoid (in left front seat back)
• Left side curtain air bag (top of left "d" pillar)
• Left side impact sensor 1 (left "b" pillar)
• Left side impact sensor 2 (left "c" pillar)
• Left side thorax air bag (in outboard side of left front seat back)
• Lt crtn squib1(+)
• Lt crtn squib1(-)
• Lt thorax squib(+)
• Lt thorax squib(-)
• Pass(+) abg squib1
• Pass(+) abg squib2
• Pass(-) abg squib1
• Pass(-) abg squib2
• Passenger air bag squib 1 (right side of dash)
• Passenger air bag squib 2 (right side of dash)
• R43
• R45
• R61
• R63
• Red
• Right side curtain air bag (top of right "d" pillar)
• Right side thorax air bag (in outboard side of right front seat back)
• Rt thorax squib(+)
• Rt thorax squib(-)
• S408
• Sde impt snsr1 lt(+)
• Sde impt snsr1 lt(-)
• Sde impt snsr2 lt(+)
• Sde impt snsr2 lt(-)
• Squib1(+) rt crtn
• Squib1(-) rt crtn
• Steering control module (steering column)

TRANSMISSION

3.6L

3.6L, 4WD Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for 3.6L, 4WD Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• (left side of dash) g911a
• 5v fd drivetrain
• A959
• Batt fd
• Batt fd 9
• Batt feed
• C267
• Can c (+)
• Can c (-)
• Can ihs (+)
• Can ihs (-)
• Cluster
• Computer data lines system
• D51
• D52
• Drivetrain 5v fd
• Drivetrain control module (under driver's seat)
• Drivetrain sens rtn
• Encdr sig tcase
• F943
• Fuse j11 30a
• Fuse m15 20a
• Fuse m20 15a
• G912a (under front of center console)
• G916a (base of left "c" pillar)
• Gnd
• Ground
• Hot at all times nca
• Hot w/ run/start relay energized nca
• Ign rs
• K504
• K594
• Lin ccn
• Mtr lk sig t case
• Nca
• Red
• S231
• S339
• S353
• Sens rtn drivetrain
• Sol fd sw battery
• Sw battery sol fd
• T301
• T313
• T315
• T316
• T317
• Tcase encdr sig
• Tcase mtr a sig
• Tcase mtr b sig
• Tcase mtr lk sig
• Totally integrated power module (left side of engine compt)
• Transfer case motor (at transfer case)
• Transfer case selector switch
• Z916

3.6L, A/T Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for 3.6L, A/T Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• A209
• B(+)
• Batt fd
• Batt sol ulk
• C161
• C192
• C267
• Can c (+)
• Can c (-)
• Circuit board
• Computer data lines system
• D51
• D52
• D64
• D65
• Electrohydraulic control unit assembly
• F202
• Fuse m28 15a
• Fuse m33 10a
• G903a (right front of engine compt)
• G909a (right rear of engine compt)
• G911a (left side of dash)
• G912a (under front of center console)
• Gnd
• Hot at all times
• Hot w/ run/start relay energized
• Ign/ulk/run/strt
• Inpt spd sig +
• Modltn o/p ctrl
• Nca
• Od sol ctrl
• Powertrain control module (right front of engine compt)
• Red
• Run/strt
• Run/strt/ ign ctrl
• Run/strt/ign ctrl
• S110
• S332
• S339
• Shft o/p ctrl
• Shift lever assembly
• Snsr i/p spd sig
• Sol (23) o/p ctrl
• Sol (34) o/p ctrl
• Spd sens rtn
• Spd snsr fd 6v
• T13
• T54
• T60
• T70
• T71
• T72
• T73
• T74
• T75
• T76
• T77
• T78
• Tcc pwm bpass ctrl
• Tcc pwm bpass o/p ctrl
• Totally integrated power module (left side of engine compt)
• Trans rng park
• Trans rnge temp snsr
• Transmission control module (left side of dash)
• Vlvs fd
• Wireless ignition node
• Z903
• Z909

5.7L

5.7L, 4WD Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for 5.7L, 4WD Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• (left side of dash) g911a
• 5v fd drivetrain
• A959
• Batt fd
• Batt fd 9
• Batt feed
• C267
• Can c (+)
• Can c (-)
• Can ihs (+)
• Can ihs (-)
• Cluster
• Computer data lines system
• D51
• D52
• Drivetrain 5v fd
• Drivetrain control module (under driver's seat)
• Drivetrain sens rtn
• Encdr sig tcase
• F943
• Fuse j11 30a
• Fuse m15 20a
• Fuse m20 15a
• G912a (under front of center console)
• G916a (base of left "c" pillar)
• Gnd
• Ground
• Hot at all times nca
• Hot w/ run/start relay energized nca
• Ign rs
• K504
• K594
• Lin ccn
• Mtr lk sig t case
• Nca
• Red
• S231
• S339
• S353
• Sens rtn drivetrain
• Sol fd sw battery
• Sw battery sol fd
• T301
• T313
• T315
• T316
• T317
• Tcase encdr sig
• Tcase mtr a sig
• Tcase mtr b sig
• Tcase mtr lk sig
• Totally integrated power module (left side of engine compt)
• Transfer case motor (at transfer case)
• Transfer case selector switch
• Z916

5.7L, A/T Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for 5.7L, A/T Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• (right front of engine compt) g903a
• 2c press sw
• 2c sol ctrl
• 4c press sw
• 4c sol ctrl
• A209
• Asd rly fd
• B (+)
• Batt fd
• Batt sol ulk
• Bus bar
• C161
• C192
• C267
• Can c (+)
• Can c (-)
• Circuit board
• Computer data lines system
• D64
• D65
• Engine controls system
• Fuse j18 20a nca
• Fuse m28 15a
• G306
• G911a (left side of dash)
• G912a (under front of center console)
• Gnd
• Hot at all times
• Ign ulk/ run/strt
• Ign ulk/run/strt
• Input spd sig
• Input speed sensor (left side of transmission)
• K856
• K900
• L/r press sw
• Line press sig
• Line pressure sensor (right rear of transmission)
• Line sens
• Lp vfs ctrl
• Lr/cc sol ctrl
• Nca
• Od press sw
• Od sol ctrl
• Output spd sig
• Output speed sensor (left side of transmission)
• P/n sig
• Powertrain control module (right front of engine compt)
• Red
• Run/start
• S110
• S113
• S116
• S117
• S123
• S125
• S331
• S339
• Sens rtn
• Shift lever assembly
• Snsr fd2
• Spd sens rtn
• Sw batt fd
• T118
• T13
• T14
• T140
• T147
• T15
• T16
• T20
• T219
• T259
• T29
• T38
• T41
• T42
• T48
• T50
• T52
• T54
• T59
• T60
• Totally integrated power module (left side of engine compt)
• Trans ms fr lr
• Trans rng park
• Trans temp sig
• Transmission control relay
• Transmission solenoid/pressure switch assembly
• Trs t1
• Trs t3
• Trs t4
• Trs t42
• Ud press sw
• Ud sol ctrl
• Wireless ignition node
• Z903

6.4L

6.4L, 4WD Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for 6.4L, 4WD Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• (left side of dash) g911a
• 5v fd drivetrain
• A959
• Batt fd
• Batt fd 9
• Batt feed
• C267
• Can c (+)
• Can c (-)
• Can ihs (+)
• Can ihs (-)
• Cluster
• Computer data lines system
• D51
• D52
• Drivetrain 5v fd
• Drivetrain control module (under driver's seat)
• Drivetrain sens rtn
• Encdr sig tcase
• F943
• Fuse j11 30a
• Fuse m15 20a
• Fuse m20 15a
• G912a (under front of center console)
• G916a (base of left "c" pillar)
• Gnd
• Ground
• Hot at all times nca
• Hot w/ run/start relay energized nca
• Ign rs
• K504
• K594
• Lin ccn
• Mtr lk sig t case
• Nca
• Red
• S231
• S339
• S353
• Sens rtn drivetrain
• Sol fd sw battery
• Sw battery sol fd
• T301
• T313
• T315
• T316
• T317
• Tcase encdr sig
• Tcase mtr a sig
• Tcase mtr b sig
• Tcase mtr lk sig
• Totally integrated power module (left side of engine compt)
• Transfer case motor (at transfer case)
• Transfer case selector switch
• Z916

6.4L, A/T Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for 6.4L, A/T Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• (right rear of engine compt) g909a
• A209
• B(+)
• Batt fd
• Btsi sol ulk
• C161
• C192
• C267
• Can c (+)
• Can c (-)
• Circuit board
• Computer data lines system
• Ctrl sw sig rem rad
• D51
• D52
• D64
• D65
• Electrohydraulic control unit assembly
• F202
• Fuse m28 15a
• Fuse m33 10a
• G909a (right rear of engine compt)
• G911a (left side of dash)
• G912a (under front of center console)
• Gnd
• Horn switch
• Hot at all times
• Hot w/ run/start relay energized
• Ign/ulk/run/strt
• Inpt spd sig +
• Left radio/paddle remote switch
• Lin sccm
• Modltn o/p ctrl
• Nca
• Od sol ctrl
• Powertrain control module (right front of engine compt)
• Red
• Rem rad ctrl sw sig
• Rem rad sw snse rtn
• Right radio/paddle remote switch
• Run/strt
• Run/strt/ign ctrl
• S271
• S272
• S273
• S274
• S331
• S332
• S339
• Shft o/p ctrl
• Shift lever assembly
• Snse rtn rem rad sw
• Snsr i/p spd sig
• Sol (23) o/p ctrl
• Sol (34) o/p ctrl
• Spd sens rtn
• Spd snsr fd 6v
• Speed control switch
• T13
• T54
• T60
• T70
• T71
• T72
• T73
• T74
• T75
• T76
• T77
• T78
• Tcc pwm bpass ctrl
• Tcc pwm bpass o/p ctrl
• Totally integrated power module (left side of engine compt)
• Trans rng park
• Trans rnge temp snsr
• Transmission control module (left side of dash)
• Trx
• Vlvs fd
• Wireless ignition node
• Z903
• Z909

6.4L, Rear Differential Lock Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for 6.4L, Rear Differential Lock Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• (base of left "c" pillar) g916a
• A206
• A903
• Batt fd 3
• C316
• Can c (+)
• Can c (-)
• Computer data lines system
• D51
• D52
• Ele brk conn
• Electronic limited slip differential module (under left side of rear seat)
• Electronic limited slip differential motor (under center rear of vehicle)
• F943
• Fuse 30a
• Fuse block
• Fuse m15 20a
• Fuse m2 20a
• Gnd
• Hot at all times
• Hot w/ run/start relay energized nca
• Ign rs
• Mtr clamp in out
• Mtr clamp out in
• Mtr in out
• Mtr out in
• Nca
• Position sense fd
• Position sense rtn
• Power distribution system
• Rear differential solenoid
• Red
• S324
• S353
• Sig1
• Sig2
• T330
• T331
• T332
• T333
• T334
• T335
• T336
• T337
• T338
• T339
• Temp snsr rtn
• Temp snsr sig
• Totally integratted power module (left side of engine compt)
• Z916

TRUNK, TAILGATE, FUEL DOOR

Fuel Door Release Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Fuel Door Release Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• (base of left "c" pillar)
• C201
• C202
• Fuel door solenoid (left rear quarterpanel)
• Fuel door switch
• Fuel dr lk rly ctrl
• Fuse m29 10a
• G916a
• Gnd
• Hot at all times nca
• Mod fsed batt fd
• Nca
• Totally integrated power module (left side of engine compt)

Power Liftgate Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Power Liftgate Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• A115
• C320
• C390
• C392
• Can ihs (+)
• Can ihs (-)
• Center bezel lamp
• Circuit board
• Computer data lines system
• D264
• D265
• Electronic overhead module
• Fuse j2 30a
• G25
• G29
• G78
• G923a (left "d" pillar)
• Gnd
• Hot at all times
• Left liftgate pinch sensor (left side of liftgate)
• Lgate ajar sig
• Lgate cnch rel ltch (cnch)
• Lgate cnch rel ultch (rel)
• Lgate full opn sig
• Lgate mtr cls
• Lgate mtr opn
• Lgate sw ft sig
• Lgate sw rr sig
• Liftgate ajar sig
• Liftgate door latch
• Lt tape sw sig
• Ltch gear postn
• Ltch sec postn
• Nca
• P339
• Postn snsr 1 sig
• Postn snsr 2 sig
• Postn snsr fd
• Power liftgate chime
• Power liftgate drive unit
• Power liftgate module (left "d" pillar)
• Pwr lgate chme sig
• Pwr lgate mod batt fd
• Pwr lgte chme sig
• Pwr lgte lgic rtn
• Q203
• Q204
• Q205
• Q51
• Q75
• Q76
• Q78
• Q79
• Q84
• Q85
• Q88
• Q89
• Q901
• Q94
• Rear power liftgate switch
• Right liftgate pinch sensor (right side of liftgate)
• Rt tape sw sig/temp snse
• S336
• S355
• S372
• Sw mux in 2
• Totally integrated power module (left side of engine compt)
• Z923

WARNING SYSTEMS

Chime Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Chime Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• (left "d" pillar) g923a
• B(+)
• B20
• Batt fd
• Brake fluid level sensor (left rear of engine compt)
• Brake fluid lvl sw sig
• Brk lvl sw sig
• C201
• C300
• C305
• C316
• C383
• C384
• C392
• C663
• Can c (+)
• Can c (-)
• Can c +
• Can c -
• Can ihs (+)
• Can ihs (-)
• Chime sig
• Circuit board
• Cluster
• Computer data
• Computer data lines system
• D264
• D265
• D51
• D52
• Driver door latch
• Driver seat belt buckle switch
• Drv dr ajar sw in
• Drv(+)
• Drv(-)
• Fuse m20 15a
• Fuse m27 10a
• G74
• G75
• G76
• G77
• G78
• G901a (left rear of engine compt)
• G911a (left side of dash)
• G912a (under front of center console)
• G919a (base of right "c" pillar)
• G923a (left "d" pillar)
• Gnd
• Hdlp/fog lp sel sw
• Headlamp switch
• Hot at all times
• Ignition-win wireless node
• Left rear door latch
• Liftgate ajar sig
• Liftgate door latch
• Lines system
• Logic rtn
• Lr dr ajar sw sig
• Mlfnct sw rtn
• Nca
• Occupant restraint controller module (under center console)
• Park brake sw sig
• Parking brake switch (top of parking brake assembly)
• Pass dr ajar sw in
• Passenger door latch
• Power liftgate chime
• Power liftgate module (left "d" pillar)
• Prk brk sw sig
• Q901
• Q94
• R57
• R59
• Red
• Right rear door latch
• Rr dr ajar sw sig
• S230
• S231
• S336
• S355
• S501
• S600
• S700
• S800
• Sts blt sw (-)
• Sts blt sw(+)
• Totally integrated power module (left side of engine compt)
• Z923

Tire Pressure Monitoring Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Tire Pressure Monitoring Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• A27
• Batt fd
• Can c +
• Can c -
• Can c - gnd
• Can ihs (+)
• Can ihs (-)
• Circuit board
• Cluster
• Computer data lines system
• D264
• D265
• D51
• D52
• G912a (under front of center console)
• G916a (base of left "c" pillar)
• Gnd
• Hot at all times
• Ignition-win wireless node
• Ihs (-) can
• Modfsed batt fd
• Nca
• Nca fuse m27 10a
• Nca fuse m29 10a
• S230
• S326
• Tire pressure module (left "c" pillar)
• Totally integrated power module (left side of engine compt)
• Z916

WIPER/WASHER

Wiper/Washer Wiring Diagram for Jeep Grand Cherokee Laredo X 2013

List of elements for Wiper/Washer Wiring Diagram for Jeep Grand Cherokee Laredo X 2013:

• (not used)
• 87a
• Abmt temp/fcm ssr rtn 1
• Bus bar
• C202
• C204
• C316
• C395
• Can ihs (+)
• Can ihs (-)
• Circuit board
• Cluster
• Computer data lines system
• D264
• D265
• Front washer fluid level sensor (left front of engine compt, in fluid reservoir)
• Front washer pump relay (on pcb)
• Front wiper motor (top left of plenum)
• Ft wpr mtr hi spd fd
• Ft wpr mtr lo spd fd
• Ft wpr mtr prk sig
• Ft wsh mtr ctrl
• Fuse j20 25a
• Fuse j21 20a
• Fuse m24 25a
• G306
• G909a (right rear of engine compt)
• G911a (left end of dash)
• G912a (under front of center console)
• G919 (base of right "c" pillar)
• G924 (right "d" pillar)
• G931
• Gnd
• Hdlp rly ctrl
• Hdlp wsh
• Hdlp wsh mtr fd
• Hdlp wsh rly coil in
• Headlamp switch
• Headlamp washer relay
• Hot at all times
• Ign run acc
• Lin tire press
• Lo wsh sw snse
• Mlfnct
• Mlfnct sw rtn
• Nca
• Nca abmt temp/fcm ssr rtn 1 nca low wsh sw sens
• Nca can ihs (-) nca can ihs (+)
• Nca ft wpr mtr prk sig
• Nca ign run acc
• Nca rr wpr mtr prk sig
• Nca wpr on/off rly ctrl nca wpr hi/lo rly ctrl nca rr wpe/wsh sig nca batt feed nca rr wpr rly ctrl nca ft wpr wsh sig to bcm nca wsh pmp mtr fd
• Power distribution center (left side of engine compt)
• Rain sensor (forward of interior rearview mirror)
• Rear washer pump relay (on pcb)
• Rear wiper motor (in liftgate)
• Rear wiper relay (on pcb)
• Red
• Rr wpr mtr prk sig
• Rr wpr mtr sig
• Rr wsh ctrl
• S134
• S354
• Sw rtn
• Totally integrated power module (left side of engine compt)
• W17
• Windshield washer pump (on washer reservoir)
• Wiper high/low relay (on pcb)
• Wiper on/off relay (on pcb)
• Wireless ignition node