DescriptionThe vehicle is equipped with a front cigar lighter/current socket located in the centre console. Its operation is controlled by a specific relay and it is protected by a fuse, both located in the engine compartment junction unit. The direct battery supply is only enabled with the ignition key in the MAR position (INT/A). This strategy is designed to provide the maximum current to the engine whilst it is switched on, given the high absorption of any consumers connected to the socket. The cigar lighter/current socket has its own internal lighting which is activated when the side lights are on.To operate the cigar lighter, simply press the knob: after a few seconds it pops out automatically, ready for use.
Functional description The power supply for the cigar lighter/current socket P050 is controlled by the ignition (INT/A), therefore excluded whilst the engine is being started, and is operated by relay T08. The relay coil receives a direct battery supply; when the ignition key is turned to position MAR, the relay closes its internal contact, thereby providing a supply to the current socket. The body computer M001 only supplies the current socket internal light, from pin 7 connector E, when the side lights are switched on (for further details SeeE2530 INSTRUMENT LIGHTING ). 767 Earth C020 is fastened to the passenger compartment floor and is located near the right front wheel arch (footwell area).
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Remove the cable pass on the right side of the vehicle from itsseating and open the cover.2. Remove the adhesive tape (2a) present on the wiring (2b) andrelease the windscreen/rear window washer tubes (2c).Release the wiring from the cable pass.Following the same procedure, release thewiring from the cable pass on the left of the vehicle.2046933
5505C34
768769
5505C35
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect the aerial coaxial cable connections.2. Disconnect the electrical connections (2a), (2b), (2c), (2d),(2e) and (2f).2046939
767It is not possible toorder a single lock barrel or to order barrels using only the partcode. When ordering barrels, observe the special procedure set outin operation 5580 - Special Accessories. 768769
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disengage the fixing lugs (1a) and remove the cover (1b).2046919
5505A32
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Disconnect the battery negativeterminal.2753188-7040A37fuse box cover - r r1. Undo the retaining bolts.Disconnect the electrical connections.2. Remove the body computer.2046922
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Open the fixing bolt cover plugs.2. Undo the retaining bolts.3. Remove the grab handle.2047313
7065C31
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Undo the retaining bolts.2. Remove the interior grab handle mounting.2047314
7065C34
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Undo retaining bolts2. Release the sun visor and remove it.3. Undo retaining bolts4. Remove the mount.2047315
7065C68
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Raise the mounting (1a) for the interior rear view mirror releasingit upwards from the retaining plate (1b) secured to the glass.2047316
7065C69
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21The following procedure illustratesthe refitting of the plate for the rear view mirror on the glassbecause, if it is correctly secured, it cannot be removed.767Do not attempt to remove the platefor the rear view mirror from the glass because this could damagethe actual glass.
7065C73
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Disconnect the battery negativeterminal.2753327-7065C84front power point housing - r r1. Release the retaining (1a) from the housing (1b) and extractthe ring nut (1c).2. Extract the bulb holder with the bulb.3. Extract the bulb, which is a press fit, from the bulb holder.2047318
7065C84
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Disconnect the battery negativeterminal.1. Extract the current socket housing (1a) using the special tool(1b).767The tool should engage in therecesses (1c) of the current socket housing.2. Disconnect the electrical connection.Remove the current socket housing.2047319
