ENGINE PERFORMANCE – Dodge Caliber SXT 2010 – SYSTEM WIRING DIAGRAMS

ENGINE PERFORMANCE

2.0L

2.0L, Engine Performance Wiring Diagram (1 of 5) for Dodge Caliber SXT 2010

List of elements for 2.0L, Engine Performance Wiring Diagram (1 of 5) for Dodge Caliber SXT 2010:

• (center front of engine compt, above left radiator fan)
• (left side of body, below front door opening)
• (under front of center floor console) g300
• A804
• A931
• App sensor ground 1
• App sensor ground 2
• App sig 2
• App signal 1
• B(+)
• B15
• B16
• Brake signal 1
• Brake signal 2
• C10
• C100
• C103
• C105
• C11
• Can c bus (+)
• Can c bus (-)
• Circuit board
• Clutch interlock signal
• Clutch interlock switch (m/t) (top of clutch pedal assembly)
• Computer data lines system
• Control fuel pump
• Control starter
• D64
• D65
• Enable
• Esm signal
• Evap purge control
• Evap purge return
• Evap purge solenoid (lower left rear of engine compt)
• Evap system monitor switch (near evap canister)
• Exterior lights system
• F202
• F342
• F856
• F963
• Fuel pump control
• Fuse 10a
• Fuse 15a
• Fuse 30a
• Fuse 40a
• Fused b(+)
• Fused main relay out
• G103
• Gen sense
• Ground
• Hot at all times
• Ign sw out (run-start)
• K107
• K141
• K167
• K23
• K29
• K299
• K31
• K400
• K51
• K52
• K70
• K858
• K904
• L53
• Main relay control
• O2 1/2 heater control
• O2 1/2 return
• O2 1/2 signal
• Powertrain control module (left rear of engine compt)
• Red
• S/c signal 1
• S/c signal 2
• S/c sw ground
• S003
• S007 (left side of engine compt, in pcm c1 breakout)
• S306 (left side of body, below front door opening)
• S308
• Signal esm
• Start
• Start enable
• Starter control
• Starting/charging system
• Stop lamp sw out
• T141
• T752
• Totally integrated power module (left side of engine compt)
• Transmission range sensor
• V71
• V72
• V937
• Z932

2.0L, Engine Performance Wiring Diagram (2 of 5) for Dodge Caliber SXT 2010

List of elements for 2.0L, Engine Performance Wiring Diagram (2 of 5) for Dodge Caliber SXT 2010:

• (behind left kick panel) (except srt) g301 (behind left quarterpanel) (srt) g303
• (right rear of engine) camshaft position solenoid 1/2
• (top left side of engine) fuel injectors
• 5v sply
• 87a
• Accelerator pedal position sensor (top of accelerator pedal bracket)
• App sens gnd 1
• App sens gnd 2
• App sig 1
• App sig 2
• Brake sig 1
• Brake sig 2
• C103
• C104
• C201
• Fuse/relay block (left front corner of engine compt)
• Fused b(+)
• G102
• Gnd
• Ground
• Ign sw out (run- start)
• Left multi-function switch
• Main relay
• Oxygen sensor 1/2 (exhaust system)
• Radiator fan series/ parallel relay
• Red
• S/c
• S/c sw
• S103
• Signal 1
• Signal 2
• Stop lamp switch (top of brake pedal assembly)
• Stop lp
• Sw out

2.0L, Engine Performance Wiring Diagram (3 of 5) for Dodge Caliber SXT 2010

List of elements for 2.0L, Engine Performance Wiring Diagram (3 of 5) for Dodge Caliber SXT 2010:

• (left front of engine) camshaft position solenoid 1/1
• (near breakout for ignition coil 4) s104
• (top right side of engine) ignition coils
• A/c compressor control
• A/c compressor solenoid (left front of engine)
• C27
• Cmp 1/2 signal
• Ect 2 signal
• Eot signal
• Etc motor (+)
• Etc motor (-)
• F855
• G104
• G24
• Iat signal
• Ignition capacitor (right rear of engine)
• Injector 1 control
• Injector 2 control
• Injector 3 control
• Injector 4 control
• K11
• K12
• K124
• K126
• K13
• K14
• K21
• K222
• K41
• K441
• K601
• K857
• K902
• K99
• Mfv control
• O2 1/1 heater control
• O2 1/1 return
• O2 1/1 signal
• Powertrain control module (left rear of engine compt)
• S108

2.0L, Engine Performance Wiring Diagram (4 of 5) for Dodge Caliber SXT 2010

List of elements for 2.0L, Engine Performance Wiring Diagram (4 of 5) for Dodge Caliber SXT 2010:

• (behind left center of dash) evaporator temperature sensor
• (brake fluid reservoir) brake fluid level sensor
• (left side of engine) s107
• (top left side of fuel tank) fuel pump module
• A/c heater control
• Aat
• Aat signal
• Ambient air temperature sensor (left front of engine compt)
• B20
• Brk fluid lvl sw sns
• C200
• Camshaft position sensor 1/2 (right rear of engine)
• Can b bus (+)
• Can b bus (-)
• Can bus (+)
• Can bus (-)
• Circuit board
• Ckp signal
• Cluster
• Cmp 1/2 signal
• Computer data lines system
• Control out fuel pump
• Crankshaft position sensor (right rear of engine)
• Engine coolant temperature sensor 2 (left side of engine)
• Evap rtn
• Evap sig
• Evap temp sensor signal
• Fuel lvl signal 1
• Fuel pump control out
• G104
• G300 (under front of center floor console)
• G31
• G931
• Ground
• Ground c1
• Intake air temperature sensor (rear of engine)
• Oil temperature sensor (front of engine)
• Oxygen sensor 1/1 (right rear of engine, in exhaust)
• Return
• Return aat
• S102 (breakout for powertrain control module c2)
• S108
• Sensor ground
• Signal 1 fuel lvl
• Totally integrated power module (left side of engine compt)
• Z906

2.0L, Engine Performance Wiring Diagram (5 of 5) for Dodge Caliber SXT 2010

List of elements for 2.0L, Engine Performance Wiring Diagram (5 of 5) for Dodge Caliber SXT 2010:

• (left side of engine) knock sensor
• (left side of engine) throttle body
• (not used)
• C100
• Camshaft position sensor 1/1 (left rear of engine)
• Ckp signal
• Cmp 1/1 control
• Cmp 1/1 signal
• Cmp 1/2 control
• Coil 1 control
• Coil 2 control
• Coil 3 control
• Coil 4 control
• Ect 1 signal
• Engine coolant temperature sensor 1 (rear of cylinder head)
• Engine oil pressure switch (left side of engine)
• Eop signal
• Etc motor (+)
• Etc motor (-)
• G104
• Gen field control
• Ground
• K122
• K15
• K17
• K18
• K19
• K20
• K22
• K24
• K276
• K42
• K44
• K602
• K76
• K900
• K915
• K922
• K942
• Ks return
• Ks signal
• Manifold flow valve (left rear of engine)
• Map sensor (left front of engine)
• Map signal
• Mfv control
• Mfv signal
• Oil temp sens sig
• Powertrain control module (left rear of engine compt)
• S105 (left front of engine)
• S106 (left side of engine)
• S108
• Sensor ground
• Starting/ charging system
• Tp sensor ground
• Tp signal 1
• Tp signal 2

2.4L

2.4L, Engine Performance Wiring Diagram (1 of 5) for Dodge Caliber SXT 2010

List of elements for 2.4L, Engine Performance Wiring Diagram (1 of 5) for Dodge Caliber SXT 2010:

• (center front of engine compt, above left radiator fan)
• (left side of body, below front door opening)
• (under front of center floor console) g300
• A804
• A931
• App sensor ground 1
• App sensor ground 2
• App sig 2
• App signal 1
• B(+)
• B15
• B16
• Brake signal 1
• Brake signal 2
• C10
• C100
• C103
• C105
• C11
• Can c bus (+)
• Can c bus (-)
• Circuit board
• Clutch interlock signal
• Clutch interlock switch (m/t) (top of clutch pedal assembly)
• Computer data lines system
• Control fuel pump
• Control starter
• D64
• D65
• Enable
• Esm signal
• Evap purge control
• Evap purge return
• Evap purge solenoid (lower left rear of engine compt)
• Evap system monitor switch (near evap canister)
• Exterior lights system
• F202
• F342
• F856
• F963
• Fuel pump control
• Fuse 10a
• Fuse 15a
• Fuse 30a
• Fuse 40a
• Fused b(+)
• Fused main relay out
• G103
• Gen sense
• Ground
• Hot at all times
• Ign sw out (run-start)
• K107
• K141
• K167
• K23
• K29
• K299
• K31
• K400
• K51
• K52
• K70
• K858
• K904
• L53
• Main relay control
• O2 1/2 heater control
• O2 1/2 return
• O2 1/2 signal
• Powertrain control module (left rear of engine compt)
• Red
• S/c signal 1
• S/c signal 2
• S/c sw ground
• S003
• S007 (left side of engine compt, in pcm c1 breakout)
• S306 (left side of body, below front door opening)
• S308
• Signal esm
• Start
• Start enable
• Starter control
• Starting/charging system
• Stop lamp sw out
• T141
• T752
• Totally integrated power module (left side of engine compt)
• Transmission range sensor
• V71
• V72
• V937
• Z932

2.4L, Engine Performance Wiring Diagram (2 of 5) for Dodge Caliber SXT 2010

List of elements for 2.4L, Engine Performance Wiring Diagram (2 of 5) for Dodge Caliber SXT 2010:

• (behind left kick panel) (except srt) g301 (behind left quarterpanel) (srt) g303
• (right rear of engine) camshaft position solenoid 1/2
• (top left side of engine) fuel injectors
• 5v sply
• 87a
• Accelerator pedal position sensor (top of accelerator pedal bracket)
• App sens gnd 1
• App sens gnd 2
• App sig 1
• App sig 2
• Brake sig 1
• Brake sig 2
• C103
• C104
• C201
• Fuse/relay block (left front corner of engine compt)
• Fused b(+)
• G102
• Gnd
• Ground
• Ign sw out (run- start)
• Left multi-function switch
• Main relay
• Oxygen sensor 1/2 (exhaust system)
• Radiator fan series/ parallel relay
• Red
• S/c
• S/c sw
• S103
• Signal 1
• Signal 2
• Stop lamp switch (top of brake pedal assembly)
• Stop lp
• Sw out

2.4L, Engine Performance Wiring Diagram (3 of 5) for Dodge Caliber SXT 2010

List of elements for 2.4L, Engine Performance Wiring Diagram (3 of 5) for Dodge Caliber SXT 2010:

• (left front of engine) camshaft position solenoid 1/1
• (near breakout for ignition coil 4) s104
• (top right side of engine) ignition coils
• A/c compressor control
• A/c compressor solenoid (left front of engine)
• C27
• Cmp 1/2 signal
• Ect 2 signal
• Eot signal
• Etc motor (+)
• Etc motor (-)
• F855
• G104
• G24
• Iat signal
• Ignition capacitor (right rear of engine)
• Injector 1 control
• Injector 2 control
• Injector 3 control
• Injector 4 control
• K11
• K12
• K124
• K126
• K13
• K14
• K21
• K222
• K41
• K441
• K601
• K857
• K902
• K99
• Mfv control
• O2 1/1 heater control
• O2 1/1 return
• O2 1/1 signal
• Powertrain control module (left rear of engine compt)
• S108

2.4L, Engine Performance Wiring Diagram (4 of 5) for Dodge Caliber SXT 2010

List of elements for 2.4L, Engine Performance Wiring Diagram (4 of 5) for Dodge Caliber SXT 2010:

• (behind left center of dash) evaporator temperature sensor
• (brake fluid reservoir) brake fluid level sensor
• (left side of engine) s107
• (top left side of fuel tank) fuel pump module
• A/c heater control
• Aat
• Aat signal
• Ambient air temperature sensor (left front of engine compt)
• B20
• Brk fluid lvl sw sns
• C200
• Camshaft position sensor 1/2 (right rear of engine)
• Can b bus (+)
• Can b bus (-)
• Can bus (+)
• Can bus (-)
• Circuit board
• Ckp signal
• Cluster
• Cmp 1/2 signal
• Computer data lines system
• Control out fuel pump
• Crankshaft position sensor (right rear of engine)
• Engine coolant temperature sensor 2 (left side of engine)
• Evap rtn
• Evap sig
• Evap temp sensor signal
• Fuel lvl signal 1
• Fuel pump control out
• G104
• G300 (under front of center floor console)
• G31
• G931
• Ground
• Ground c1
• Intake air temperature sensor (rear of engine)
• Oil temperature sensor (front of engine)
• Oxygen sensor 1/1 (right rear of engine, in exhaust)
• Return
• Return aat
• S102 (breakout for powertrain control module c2)
• S108
• Sensor ground
• Signal 1 fuel lvl
• Totally integrated power module (left side of engine compt)
• Z906

2.4L, Engine Performance Wiring Diagram (5 of 5) for Dodge Caliber SXT 2010

List of elements for 2.4L, Engine Performance Wiring Diagram (5 of 5) for Dodge Caliber SXT 2010:

• (left side of engine) knock sensor
• (left side of engine) throttle body
• (not used)
• C100
• Camshaft position sensor 1/1 (left rear of engine)
• Ckp signal
• Cmp 1/1 control
• Cmp 1/1 signal
• Cmp 1/2 control
• Coil 1 control
• Coil 2 control
• Coil 3 control
• Coil 4 control
• Ect 1 signal
• Engine coolant temperature sensor 1 (rear of cylinder head)
• Engine oil pressure switch (left side of engine)
• Eop signal
• Etc motor (+)
• Etc motor (-)
• G104
• Gen field control
• Ground
• K122
• K15
• K17
• K18
• K19
• K20
• K22
• K24
• K276
• K42
• K44
• K602
• K76
• K900
• K915
• K922
• K942
• Ks return
• Ks signal
• Manifold flow valve (left rear of engine)
• Map sensor (left front of engine)
• Map signal
• Mfv control
• Mfv signal
• Oil temp sens sig
• Powertrain control module (left rear of engine compt)
• S105 (left front of engine)
• S106 (left side of engine)
• S108
• Sensor ground
• Starting/ charging system
• Tp sensor ground
• Tp signal 1
• Tp signal 2