All Wiring Diagrams for GMC Canyon 2008 model

AIR CONDITIONING

Compressor Wiring Diagram for GMC Canyon 2008

List of elements for Compressor Wiring Diagram for GMC Canyon 2008:

• 4.3l
• 4.8l, 5.3l & 6.0l
• 5v ref
• 6.6l
• A/c cmprsr fuse 57 15a
• A/c compressor clutch (4.3l: at left front of engine) (4.8l, 5.3l & 6.0l: at lower right front of engine) (6.6l: top front of engine)
• A/c comprsr relay 74
• A/c low pressure switch (on side of accumulator)
• A/c refrigerant pressure sensor
• A/c request sig
• Bi-lev
• Body control module (bcm) (behind lower right side of dash)
• Body fuse block (under left front seat)
• Clutch rly ctrl
• Computer data lines system
• Def
• Engine control module (ecm) (left side of engine compt)
• G102 (6.6l: left front lower side of the engine block) (except 6.6l: on left rear of engine)
• G304 (behind right kick panel)
• Gmlan (+)
• Gmlan (-)
• Heat
• Heat/def
• Hot at all times
• Hot in run
• Hvac 2 fuse 1 10a
• Hvac control assembly
• J102
• J249
• Logic
• Low ref
• Max norm
• Off
• Press sens
• Tan
• Underhood fuse block (on left side of engine compt)
• Vent
• W/ electric rear window defogger & power mirrors

Manual A/C Wiring Diagram for GMC Canyon 2008

List of elements for Manual A/C Wiring Diagram for GMC Canyon 2008:

• (hvac harness, 14 cm from recirculation actuator breakout toward blower motor resistor assembly) j202
• (i/p harness, 6 cm from instrument cluster breakout)
• 5v ref
• A/c clutch 65 diode
• A/c cmprsr fuse 10a
• A/c compressor clutch (left front of engine)
• A/c fuse 10a
• A/c refrigerant pressure sensor (right rear of engine compt)
• A/c relay
• A/c req sig
• A26
• A42
• A43
• A47
• B x4
• Blower motor (below right side of dash)
• Blower motor resistor assembly (lower right side of dash, near blower motor)
• Blower motor switch
• Blwr fuse 30a
• Body control module (bcm) (behind right kick panel)
• Computer data lines system
• Dimmer sw sig
• Dr ctrl a
• Dr ctrl b
• Engine control module (ecm) (right rear of engine compt)
• Engine coolant temperature (ect) sensor (on left rear of engine)
• Evaporator temperature sensor (lower right side of dash)
• F10 x7
• G103 (lower left side of engine)
• G106
• Gnd
• High
• Hot at all times
• Hot in run or start
• Hvac control module
• Ign 3 hvac relay
• Ign 3 voltage
• Ign fuse 15a
• Ign voltage
• Interior lights system
• J200
• Jx106 (right side of engine compt)
• Logic
• Low
• Low ref
• Nca
• Off
• Off blwr mtr ctrl
• Power distribution system
• Press sens sig
• Recirculation actuator (right side of dash)
• Rly ctrl
• Sens sig
• Serial data
• Tan
• Underhood fuse block (left front side of engine compt)
• X2 f11
• X7 f5

ANTI-LOCK BRAKES

Anti-lock Brakes Wiring Diagram for GMC Canyon 2008

List of elements for Anti-lock Brakes Wiring Diagram for GMC Canyon 2008:

• 2wd
• A11 x7
• A17
• A26
• A31
• A39
• A45
• Abs 1 fuse 30a
• Abs 2 fuse 40a
• Abs fuse 10a
• Abs ind
• Accessory switch
• B x5
• Body control module (bcm) (behind right kick panel)
• Brake fluid level switch (on brake fluid reservoir)
• Brake fluid lvl sens sig
• Brake ind
• Class 2 serial data
• Computer data lines system
• Del torque sig (nw7)
• Delivered torque signal
• Driver info center
• Electronic brake control module (ebcm) (on inner left frame rail, beside transmission)
• Engine control module (ecm) (right rear of engine compt)
• G105
• G106
• Gnd
• Hot at all times
• Hot in run or start
• Ign
• Ign voltage
• Instrument panel cluster (ipc)
• Interior lights system
• J100 (body harness, 14.5 cm from accelerator pedal position switch breakout)
• J200
• Jx105 (left side of engine compt)
• Jx106 (right side of engine compt)
• Left front wheel speed sensor (wss) (on left front hub)
• Lf whl spd control
• Lf whl spd sens sig
• Lng rate sig (4wd)
• Logic
• Longitudinal accelerometer sensor (4wd) (under driver seat, below carpet)
• Low ref (4wd
• Park brake switch (lower left end of dash)
• Park brk sw sig
• Pnk
• Red
• Req torque sig (nw7)
• Requested torque signal
• Rf whl spd control
• Rf whl spd sens sig
• Right front wheel speed sensor (wss) (on right front hub)
• Stability caution ind
• Stop fuse 20a
• Stop lamp switch (above brake pedal assembly)
• Stop lmp control
• Tan
• Tcs req indicator ctrl
• Trac ctrl sw sig
• Underhood fuse block (left front side of engine compt)
• Vss

ANTI-THEFT

Anti-theft Wiring Diagram for GMC Canyon 2008

List of elements for Anti-theft Wiring Diagram for GMC Canyon 2008:

• (top of engine, attached to fuel rail)
• 2.9l
• 3.7l
• A14
• A19
• A2 x6
• A24
• A32
• A38
• A39
• A40
• A42
• A44
• A47
• Acc
• B3 x7
• Battery +
• Body control module (bcm) (behind right kick panel)
• Class 2 data
• Class 2 serial data
• Cluster fuse 10a
• Crew cab
• Data link connector (dlc) (lower left side of dash)
• Driver door jamb switch (in left "b" pillar)
• Engine control module (ecm) (right rear of engine compt)
• Exterior lights system
• Front passenger door jamb switch (in right "b" pillar)
• Fuel inj 1
• Fuel inj 2
• Fuel inj 3
• Fuel inj 4
• Fuel inj 5
• Fuel injector
• Fuel injector (3.7l)
• G300 (under driver seat carpet)
• G301 (under front passenger seat carpet)
• Ground
• Horn rly ctrl
• Horns system
• Hot at all times
• Hot in run & start
• Ign key resistor sig
• Ign volt
• Ignition switch
• Inj fuse 15a
• Instrument panel cluster (ipc)
• J104
• J303
• Key-in switch
• Left rear door jamb switch (in left "c" pillar)
• Lf door ajar
• Lr door ajar
• Off
• Park lamp rly ctrl
• Pnk
• Rf door ajar
• Right rear door jamb switch (in right "c" pillar)
• Rr door ajar
• Run
• Security ind
• Start
• Tbc fuse 10a
• Theft resistor
• Trn/hazrd rear fuse 15a
• Turn/ hazrd frt fuse 15a
• Underhood fuse block (left front side of engine compt)
• X2 f4

BODY CONTROL MODULES

Body Control Modules Wiring Diagram (1 of 2) for GMC Canyon 2008

List of elements for Body Control Modules Wiring Diagram (1 of 2) for GMC Canyon 2008:

• (under front passenger seat carpet) g301
• A/c req sig
• A10
• A11
• A12
• A13
• A14
• A15
• A16
• A17
• A18
• A19
• A20
• A21
• A22
• A23
• A24
• A25
• A26
• A27
• A28
• A29
• A30
• A31
• A32
• A33
• A34
• A35
• A36
• A37
• A38
• A39
• A40
• A41
• A42
• A43
• A44
• A45
• A46
• A47
• A48
• Accessory voltage
• Air conditioning system
• Battery +
• Beam select rly ctrl
• Body control module (behind right kick panel)
• Brake fluid level sen sig
• Class 2 serial data
• Computer data lines system
• Courtesy lamp low ctrl
• Courtesy lamps pwr
• Courtesy lmp pwr
• Door locks system
• Door unlock ctrl
• Engine controls system
• Exterior lights system
• Fog lamp rly ctrl
• Ground
• Headlamp rly ctrl
• Headlights system
• Horn rly ctrl
• Horns system
• Hot at all times
• Ign 3 voltage
• Instrument cluster system
• Interior lights system
• J304
• Left trn sig lamp pwr
• Lf door ajar sw sig
• Lr door ajar sw sig
• Lr turn sig lamps pwr
• Mirrors system
• Park brake sw sig
• Park lamp power
• Park lamp rly ctrl
• Pass dr lock sw lock ctrl
• Pnk
• Power distribution system
• Rap rly coil ctrl
• Red
• Right trn sig lamp pwr
• Rr door ajar sw sig
• Rr turn sig lamps pwr
• Run/crnk voltage
• Starting/charging system
• Tbc fuse 10a
• Trn/hazrd frt fuse 15a
• Trn/hazrd rear fuse 15a
• Underhood fuse block (left front side of engine compt)
• Windshield washer pmp ctrl
• Wiper mtr prk sw sig
• Wiper sw sig 2
• Wiper/washer system

Body Control Modules Wiring Diagram (2 of 2) for GMC Canyon 2008

List of elements for Body Control Modules Wiring Diagram (2 of 2) for GMC Canyon 2008:

• A10
• A11
• A12
• A13
• A14
• A15
• A16
• A17
• A18
• A19
• A20
• A21
• A22
• A23
• A24
• A25
• A26
• A27
• A28
• A29
• A30
• A31
• A32
• A33
• A34
• A35
• A36
• A37
• A38
• A39
• A40
• A41
• A42
• A43
• A44
• A45
• A46
• A47
• A48
• Acc
• Accessory voltage
• Ambient light sens low ref
• Ambient light sens sig
• Anti-lock brakes system
• Anti-theft system
• Body control module (behind right kick panel)
• Cargo lamp sw sig
• Class 2 serial data
• Computer data lines system
• Courtesy lamp low ctrl
• Courtesy lamps pwr
• Dome override sw sig
• Exterior lights system
• Flash to pass sw sig
• Fog lamps enable
• Front fog lamps ind ctrl
• Hazard sw sig
• Headlamps dim sw hi beam sig
• Headlamps sw hi on sig
• Headlamps sw off sig
• Headlights system
• Horn rly ctrl
• Horns system
• Hot at all times
• I/p lamp dimmer sw sig
• I/p lamps dim ctrl
• Ign key resistor sig
• Ignition switch
• Int lamp sw sig
• Interior lights system
• Key-in switch
• Low ref
• Lr turn sig lamps pwr
• Off
• Off/run/crnk voltage
• Park lamps rly ctrl
• Red
• Rr turn sig lamps pwr
• Run
• Run/crank voltage
• Security ind lamp
• Shift interlock system
• Shift sol pwr
• Start
• Tcs req ind ctrl
• Traction ctrl sw sig
• Turn sig sw sig
• Windshield washer pmp ctrl
• Wiper sw sig 1
• Wiper/washer system

COMPUTER DATA LINES

Computer Data Lines Wiring Diagram for GMC Canyon 2008

List of elements for Computer Data Lines Wiring Diagram for GMC Canyon 2008:

• (right side of engine compt) jx106
• (under driver seat carpet) g300
• 2wd
• 4wd
• A/t
• A38
• A39
• A41
• A42
• A44
• A47
• Aux pwr 1 fuse 20a
• Body control module (bcm) (behind right kick panel)
• Class 2 serial data
• Class 2 serial data x1
• Data bus +
• Data bus -
• Data link connector (dlc) (lower left side of dash)
• Data link resistor
• Digital radio receiver (center of dash)
• Electronic brake control module (ebcm) (on inner left frame rail, beside transmission)
• Engine control module (ecm) (right rear of engine compt)
• G106
• Generator battery control module (left front of engine compt, near battery)
• Hot at all times
• If equipped
• Inflatable restraint sensing & diagnostic module (beneath center console)
• Instrument panel cluster (ipc)
• J200
• J201
• M/t
• Power distribution system
• Radio
• Serial data +
• Serial data -
• Tan
• Transfer case shift control module (under driver seat carpet)
• Transmission control module (tcm)
• Underhood fuse block (left front side of engine compt)
• Vehicle communication interface module (vcim) (right side of dash)
• W/ onstar
• W/o onstar

CRUISE CONTROL

Cruise Control Wiring Diagram for GMC Canyon 2008

List of elements for Cruise Control Wiring Diagram for GMC Canyon 2008:

• (above brake pedal assembly) stop lamp switch
• (body harness, 14.5 cm from accelerator pedal position switch breakout) j100
• 5-volt reference
• A/t
• A11
• Accelerator pedal position (app) sensor (on accelerator bracket)
• App sensor 1 signal
• App sensor 2 signal
• Class 2 serial data
• Cluster fuse 10a
• Clutch pedal position (cpp) sensor (m/t)
• Coast
• Computer data lines system
• Cruise
• Cruise control release signal
• Cruise control release switch (above brake pedal assembly)
• Cruise control switch
• Cruise control switch signal
• Cruise fuse 10a
• Cruise indicator
• Engine control module (ecm) (right rear of engine compartment)
• G105
• Hot at all times
• Hot in run or start
• Ignition
• Instrument panel cluster (ipc)
• Jx105 (left side of engine compt)
• Logic
• Low reference
• M/t
• Pnk
• Power distribution system
• Resume/ accel
• Run/crank relay
• Sens sig
• Serial data +
• Serial data -
• Set/
• Stop fuse 20a
• Stop lamp control
• Switch
• Tac motor control-1
• Tac motor control-2
• Tan
• Throttle body (on intake, near map sensor)
• Tp sensor 1 signal
• Tp sensor 2 signal
• Transmission control module
• Turn signal/multi-function switch
• Underhood fuse block (left front side of engine compartment)
• Vehicle speed sensor (vss) (2wd: left rear of transmission) (4wd: on left rear of transfer case)
• Vss high sig
• Vss high signal
• Vss low sig
• Vss low signal

ENGINE PERFORMANCE

2.9L VIN 9

2.9L VIN 9, Engine Performance Wiring Diagram (1 of 5) for GMC Canyon 2008

List of elements for 2.9L VIN 9, Engine Performance Wiring Diagram (1 of 5) for GMC Canyon 2008:

• (chassis harness, 39 cm before fuel pump & sender assembly) j310
• 4wd low signal
• 5v reference
• A/c compressor clutch rly ctrl
• A11
• Acc
• Accelerator pedal position (app) sensor (on accelerator bracket)
• Accy volt
• Air conditioning system
• Air solenoid relay ctrl
• Anti-lock brakes system
• App sensor 1 signal
• App sensor 2 signal
• Battery positive voltage
• Body control module (bcm) (behind right kick panel)
• Class 2 serial data
• Cnstr vent fuse 10a
• Computer data lines system
• Cruise control release signal
• Cruise control switch signal
• Cruise control system
• Engine control module (ecm) (right rear of engine compt)
• Evap canister vent sol ctrl
• Fuel level sensor signal
• Fuel pump relay control
• Fuel tank pressure (ftp) sensor (at top left rear of fuel tank)
• Fuel tank pressure sensor signal
• Hot at all times
• Ignition switch
• Ignition voltage
• Low reference
• Mil control
• Off
• Pnk
• Powertrain relay control
• Run
• Start
• Starter enable relay control
• Starting/charging system
• Stop fuse 20a
• Stop lamp control
• Stop lamp switch (above brake pedal assembly)
• Tan
• Transmissions system
• Underhood fuse block (left front side of engine compt)
• Vehicle speed signal

2.9L VIN 9, Engine Performance Wiring Diagram (2 of 5) for GMC Canyon 2008

List of elements for 2.9L VIN 9, Engine Performance Wiring Diagram (2 of 5) for GMC Canyon 2008:

• (in engine harness, 24 cm before generator battery control module breakout) j105
• A red
• Air pump fuse 50a
• Air pump relay
• Clstr fuse 10a
• Computer
• Data lines
• Ecm-b fuse 10a
• Etc fuse 15a
• Evaporative emission (evap) canister vent solenoid valve (on side of evap canister, above spare tire)
• F11
• Fuel pump & sender assembly (top of fuel tank)
• Fuel pump relay
• Fuel/pump fuse 15a
• G101 (lower left side of engine)
• G103 (lower left side of engine)
• G105
• Hot at all times
• Ign
• Ind up shift
• Instrument panel cluster (ipc)
• J401
• Jx105 (left side of engine compt)
• Logic
• Mil ind
• Nca
• O2 snsr fuse 15a
• Pnk
• Pnk pnk
• Pwr/trn relay
• Red
• Secondary air injection (air) pump
• Secondary air injection (air) pump fuse block (if equipped)
• Secondary air injection (air) pump relay
• Secondary air injection (air) pump solenoid (if equipped) (upper right side of engine)
• Serial data
• System
• Underhood fuse block (left front side of engine compt)

2.9L VIN 9, Engine Performance Wiring Diagram (3 of 5) for GMC Canyon 2008

List of elements for 2.9L VIN 9, Engine Performance Wiring Diagram (3 of 5) for GMC Canyon 2008:

• (on top left of valve cover) ignition coil 1
• (on top left of valve cover) ignition coil 3
• (on top right of valve cover) ignition coil 2
• (on top right of valve cover) ignition coil 4
• (top of engine, attached to fuel rail) fuel injectors
• 5v reference
• A pnk
• Air conditioning system
• Air relay control
• Anti-lock brakes system
• Computer data lines system
• Delivered torque
• Duty cycle signal
• Engine control module (ecm) (right rear of engine compt)
• Evap canister purge solenoid control
• Generator
• Generator field
• High speed gmlan
• J104
• Low reference
• Nca
• Pnk
• Pnp/clutch
• Regulator ctrl
• Requested torque
• Serial data bus +
• Serial data bus -
• Signal
• Spark plug
• Start sw sig
• Starting/charging system
• Tan

2.9L VIN 9, Engine Performance Wiring Diagram (4 of 5) for GMC Canyon 2008

List of elements for 2.9L VIN 9, Engine Performance Wiring Diagram (4 of 5) for GMC Canyon 2008:

• (lower left side of engine) g103
• (on intake, near map sensor) throttle body
• A/c refrigerant
• Air conditioning system
• Air inj reaction
• Clutch pedal pos sig
• Clutch pedal position (cpp) sensor
• D11
• E11
• Ect sensor signal
• Engine control module (ecm) (right rear of engine compt)
• Engine coolant temperature (ect) sensor (on left rear of engine)
• Erls fuse 15a
• Evaporative emission (evap) canister purge solenoid valve (left side of engine, below intake)
• F11
• Hot w/ run/crnk relay energized
• Ign fuse 15a
• Inj fuse 15a
• Instrument cluster system
• Manifold absolute pressure (map) sensor (top left side of engine, on intake manifold)
• Map sensor signal
• Nca
• Oil press sw sig
• Pcm-i fuse 10a
• Pnk
• Press sens sig
• Tan
• Underhood fuse block (left front side of engine compt)
• Vehicle speed sensor (vss) (2wd: left rear of transmission) (4wd: on left rear of transfer case)
• Vss high signal
• Vss low signal

2.9L VIN 9, Engine Performance Wiring Diagram (5 of 5) for GMC Canyon 2008

List of elements for 2.9L VIN 9, Engine Performance Wiring Diagram (5 of 5) for GMC Canyon 2008:

• (in engine harness, 24 cm before generator battery control module breakout) j105
• (lower left side of engine) g102
• 5v reference
• A11
• B11
• C11
• Camshaft position (cmp) actuator solenoid bank 1 exhaust (on top right b
• Camshaft position (cmp) sensor (top right front of engine)
• Ckp sensor signal
• Cmp actuator solenoid control
• Cmp sensor signal
• Crankshaft position (ckp) sensor (left rear of engine block, below starter)
• Engine control module (ecm) (right rear of engine compt)
• Front of engine)
• Fuel injector 1 control
• Fuel injector 2 control
• Fuel injector 3 control
• Fuel injector 4 control
• Ground
• Heated oxygen sensor (ho2s) 1 (right side of engine, on exhaust manifold)
• Heated oxygen sensor (ho2s) 2 (in exhaust pipe, adjacent to transmission)
• Ho2s heater high ctrl sens 1
• Ho2s heater low ctrl sens 2
• Ho2s high signal sensor 1
• Ho2s high signal sensor 2
• Ho2s low signal sensor 1
• Ho2s low signal sensor 2
• Iat sensor signal
• Ic 1 control
• Ic 2 control
• Ic 3 control
• Ic 4 control
• Ignition voltage
• Instrument cluster system
• Intake air temperature (iat)/mass air flow (maf) sensor (in air intake duct, top right of engine)
• Knock sensor (ks) (on left side of engine, below intake manifold)
• Knock sensor signal
• Low reference
• Maf sensor signal
• Nca
• Pnk
• Red
• Tac motor control 1
• Tac motor control 2
• Tp sensor 1 signal
• Tp sensor 2 signal
• X2 underhood fuse block (left front x2 side of engine compt)

3.7L VIN E

3.7L VIN E, Engine Performance Wiring Diagram (1 of 5) for GMC Canyon 2008

List of elements for 3.7L VIN E, Engine Performance Wiring Diagram (1 of 5) for GMC Canyon 2008:

• (chassis harness, 39 cm before fuel pump & sender assembly) j310
• 4wd low signal
• 5v ref
• A/c compressor clutch rly ctrl
• A11
• Acc
• Accelerator pedal position (app) sensor (on accelerator bracket)
• Accy volt
• Air conditioning system
• Air solenoid relay control
• Anti-lock brakes system
• App sensor 1 signal
• App sensor 2 signal
• Battery positive voltage
• Body control module (bcm) (behind right
• Class 2 serial data
• Cnstr vent fuse 10a
• Computer data lines system
• Cruise control release signal
• Cruise control switch signal
• Cruise control system
• Engine control module (ecm) (right rear of engine compt)
• Evap canister vent sol ctrl
• Fuel level sensor signal
• Fuel pump relay control
• Fuel tank pressure (ftp) sensor (at top left rear of fuel tank)
• Fuel tank pressure sensor signal
• Hot at all times
• Ignition switch
• Ignition voltage
• Kick panel)
• Low ref
• Low reference
• Mil control
• Off
• Pnk
• Powertrain relay control
• Run
• Start
• Starter enable relay control
• Starting/charging system
• Stop fuse 20a
• Stop lamp control
• Stop lamp switch (above brake pedal assembly)
• Tan
• Transmissions system
• Underhood fuse block (left front side of engine compt)
• Vehicle speed signal

3.7L VIN E, Engine Performance Wiring Diagram (2 of 5) for GMC Canyon 2008

List of elements for 3.7L VIN E, Engine Performance Wiring Diagram (2 of 5) for GMC Canyon 2008:

• (in engine harness, 24 cm before generator battery control module breakout) j105
• Air pump fuse 50a
• Air pump relay
• Air solenoid fuse block (lower right front of engine compt)
• Clstr fuse 10a
• Computer data lines system
• Ecm-b fuse 10a
• Etc fuse 15a
• Evaporative emission (evap) canister vent solenoid valve (on side of evap canister, above spare tire)
• F11
• Fuel pump & sender assembly (top of fuel tank)
• Fuel pump relay
• Fuel/pump fuse 15a
• G101 (lower left side of engine)
• G103 (lower left side of engine)
• G105
• Hot at all times
• Instrument panel cluster (ipc)
• J401
• Jx105 (left side of engine compt)
• Logic
• Mil ind
• Nca
• O2 snsr fuse 15a
• Pnk
• Pwr/trn relay
• Red
• Secondary air injection (air) pump (lower right front of engine compt)
• Secondary air injection (air) pump relay (lower right front of engine compt)
• Secondary air injection (air) pump solenoid (upper right side of engine)
• Serial data
• Underhood fuse block (left front side of engine compt)

3.7L VIN E, Engine Performance Wiring Diagram (3 of 5) for GMC Canyon 2008

List of elements for 3.7L VIN E, Engine Performance Wiring Diagram (3 of 5) for GMC Canyon 2008:

• (on top left of valve cover) ignition coil 1
• (on top left of valve cover) ignition coil 3
• (on top left of valve cover) ignition coil 5
• (on top right of valve cover) ignition coil 2
• (on top right of valve cover) ignition coil 4
• (top of engine, attached to fuel rail) fuel injectors
• 5v reference
• A pnk
• Air conditioning system
• Air relay control
• Anti-lock brakes system
• Computer data lines system
• Delivered torque
• Duty cycle signal
• Engine control module (ecm) (right rear of engine compt)
• Evap canister purge
• Generator
• Generator field
• High speed gmlan
• J103 pnk
• Low reference
• Nca
• Pnk
• Pnp/clutch
• Regulator ctrl
• Requested torque
• Serial data bus +
• Serial data bus -
• Signal
• Solenoid control
• Spark plug
• Start sw sig
• Starting/charging system
• Tan

3.7L VIN E, Engine Performance Wiring Diagram (4 of 5) for GMC Canyon 2008

List of elements for 3.7L VIN E, Engine Performance Wiring Diagram (4 of 5) for GMC Canyon 2008:

• (lower left side of engine) g103
• (on intake, near map sensor) throttle body
• A/c refrigerant
• Air conditioning system
• Air injection reaction
• Ctrl valve ctrl
• D11
• E11
• Ect sensor signal
• Engine control module (ecm) (right rear of engine compt)
• Engine coolant temperature (ect) sensor (on left rear of engine)
• Erls fuse 15a
• Evaporative emission (evap) canister purge solenoid valve (left side of engine, below intake)
• F11
• Hot w/ run/crnk relay energized
• Ign fuse 15a
• Inj fuse 15a
• Instrument cluster system
• Manifold absolute pressure (map) sensor (top left side of engine, on intake manifold)
• Map sensor signal
• Nca
• Oil press sw sig
• Pcm-i fuse 10a
• Pnk
• Press sens sig
• Tan
• Underhood fuse block (left front side of engine compt)

3.7L VIN E, Engine Performance Wiring Diagram (5 of 5) for GMC Canyon 2008

List of elements for 3.7L VIN E, Engine Performance Wiring Diagram (5 of 5) for GMC Canyon 2008:

• (lower left side of engine) g102
• 5v reference
• A11
• B11
• C11
• Camshaft position (cmp) actuator solenoid bank 1 exhaust (on top right b
• Camshaft position (cmp) sensor
• Ckp sensor signal
• Cmp actuator solenoid control
• Crankshaft position (ckp) sensor (left rear of engine block, below starter)
• Engine control module (ecm) (right rear of engine compt)
• Front of engine)
• Fuel injector 1 control
• Fuel injector 2 control
• Fuel injector 3 control
• Fuel injector 4 control
• Fuel injector 5 control
• Ground
• Heated oxygen sensor (ho2s) 1 (right side of engine, on exhaust manifold)
• Heated oxygen sensor (ho2s) 2 (in exhaust pipe, adjacent to transmission)
• Ho2s heater high ctrl sens 1
• Ho2s heater low ctrl sens 2
• Ho2s high signal sensor 1
• Ho2s high signal sensor 2
• Ho2s low signal sensor 1
• Ho2s low signal sensor 2
• Iat sensor signal
• Ic 1 control
• Ic 2 control
• Ic 3 control
• Ic 4 control
• Ic 5 control
• Ignition voltage
• Instrument cluster system
• Intake air temperature (iat)/mass air flow (maf) sensor (in air intake duct, top right of engine)
• Knock sensor (ks) (on left side of engine, below intake manifold)
• Knock sensor signal
• Low reference
• Maf sensor signal
• Nca
• Pnk
• Red
• Tac motor control 1
• Tac motor control 2
• Tp sensor 1 signal
• Tp sensor 2 signal
• X2 underhood fuse block (left front x2 side of engine compt)

EXTERIOR LIGHTS

Backup Lamps Wiring Diagram for GMC Canyon 2008

List of elements for Backup Lamps Wiring Diagram for GMC Canyon 2008:

• (chassis harness, 75.5 cm before x402) j404
• A trailer connector
• A/t
• Backup lamp switch (right side of transmission)
• Bck/up fuse 15a
• Exterior lamps circuit
• G105
• Hot at all times
• Hot in run or start
• Inside rearview mirror (if equipped)
• J401
• J409 (w/ trailer connection)
• Jx105 (left side of engine compt)
• Left backup lamp
• M/t
• Nca
• Park/ neutral position (pnp)
• Pnk
• Right backup lamp
• Run/ crank relay
• Switch (on lower left side of transmission)
• Underhood fuse block (left front side of engine compartment) x7
• Underhood fuse block (left front side of engine compt)

Exterior Lamps Wiring Diagram (1 of 2) for GMC Canyon 2008

List of elements for Exterior Lamps Wiring Diagram (1 of 2) for GMC Canyon 2008:

• A10
• A11
• A19
• A24
• A45
• A48
• Auto
• Body control module (bcm) (behind right kick panel)
• Frt prk lamp fuse 10a
• G105
• G106
• Haz sw sig
• Hazard switch
• Head
• Headlamp & panel dimmer switch
• Hot at all times
• Interior lights system
• J200
• Jx105 (left side of engine compt)
• Jx106 (left side of engine compt)
• Jx106 (right side of engine compt)
• Left
• Left cargo lamp
• Left front park lamp
• Left park/ turn signal lamp
• Low ref
• Off
• Park
• Park lamp relay
• Prk lmp rly
• Prk lmp sw
• Red
• Right
• Right cargo lamp
• Right front park lamp
• Right park/ turn signal lamp
• Stop fuse 20a
• Stop lamp switch (above brake pedal assembly)
• To rear prk lamp 2 fuse (diagram 2 0f 2)
• Trailer power fuse 30a
• Trn sig sw
• Turn signal/ multi-function switch
• Turn/ hazrd frt fuse 15a
• Turn/ hazrd rear fuse 15a
• Underhood fuse block (left front side of engine compt)

Exterior Lamps Wiring Diagram (2 of 2) for GMC Canyon 2008

List of elements for Exterior Lamps Wiring Diagram (2 of 2) for GMC Canyon 2008:

• (chassis harness, 13 cm from x401 & x402 breakout) j402
• (chassis harness, 14 cm from x401 & x402 breakout) j403
• (license lamp harness, 44.5 cm before right license lamp) j900
• (not used)
• A/t
• Backup lamps circuit
• Electronic brake control module (ebcm) (on inner left frame rail, beside transmission)
• Engine control module (ecm) (right rear of engine compt)
• From frt prk a lamp fuse (diagram 1 0f 2)
• Fuse holder trailer connector
• G105
• G400
• Instrument panel cluster (ipc)
• J400 (chassis harness, 40.5 cm from fuel pump & sender assembly breakout)
• J401
• J407 (w/ trailer connection) (trailer accessory harness, between left rear tail lamp connector & trailer lighting connector)
• J408 (w/ trailer connection)
• J409
• J409 (w/ trailer connection)
• J901
• Jx105 (left side of engine compt)
• Left backup lamp
• Left license lamp
• Left rear turn signal lamp
• Left stop lamp
• Left turn ind
• Logic
• Nca
• Rear prk lamp 2 fuse 10a
• Rear prk lamp fuse 15a
• Red
• Right backup lamp
• Right license lamp
• Right rear turn signal lamp
• Right stop lamp
• Right turn ind
• Stp lmp vlt
• Trailer connector
• Trailer lighting converter
• Transmission control module (tcm)
• Underhood fuse block (left front side of engine compt)
• W/o trailer connector
• X401
• X405

GROUND DISTRIBUTION

Ground Distribution Wiring Diagram (1 of 3) for GMC Canyon 2008

List of elements for Ground Distribution Wiring Diagram (1 of 3) for GMC Canyon 2008:

• 3.7l
• 4wd
• A/c clutch diode
• A/c compressor clutch
• A/t
• A11
• B11
• Battery
• Beam sel relay
• Brake fluid level switch
• Crew cab w/ power operated window
• D11
• Driver door lock/ window switch
• E11
• Electronic brake control module (ebcm)
• Engine control module (ecm)
• F11
• Front drive axle actuator
• Fuel pump relay
• G100 (next to rear side of battery)
• G101 (lower left side of engine)
• G102 (lower left side of engine)
• G103 (lower left side of engine)
• G104 (left side of engine)
• G105 (left side of engine compt, near ebcm)
• Generator battery control module
• If equipped
• Ignition coil/ module 1
• Ignition coil/ module 2
• Ignition coil/ module 3
• Ignition coil/ module 4
• Ignition coil/ module 5
• Inside rearview mirror
• J110
• J500 (driver door harness, 5 cm from left front door tweeter speaker breakout)
• Jx105
• Left rear window switch
• M/t
• Mass air flow (maf)/ intake air temperature (iat) sensor
• Nca
• Outside rearview mirror switch
• Park/ neutral position (pnp) switch
• Run/ crank relay
• Secondary air injection (air) pump
• Secondary air injection (air) pump solenoid
• Strt relay
• To jx105 (diagram 2 of 3)
• Transfer case 2/4 wheel indicator switch
• Transfer case encoder motor
• Transfer case neutral switch
• Transmission control module (tcm)
• Underhood fuse block (left front side of engine compt)
• W/ driver convenience iii sales package
• W/ onstar
• Wind- shield wiper motor
• Windshield washer fluid pump
• Wiper 2 relay
• Wiper relay

Ground Distribution Wiring Diagram (2 of 3) for GMC Canyon 2008

List of elements for Ground Distribution Wiring Diagram (2 of 3) for GMC Canyon 2008:

• (w/ power operated window) passenger door lock/ window switch
• 4wd
• Crew cab w/ power operated window
• Driver back heated seat element
• Driver cushion heated seat element
• Driver heated seat control module
• Driver seat adjuster switch
• Driver seat lumbar adjuster switch
• Electronic brake control module (ebcm)
• Fog lamp relay
• From a jx105 (diagram 1 of 3)
• From jx106 (diagram 3 of 3)
• Fuel pump & sender assembly
• G106 (right side of engine compt, behind air cleaner)
• Horn assembly
• Hvac control module
• J306 (driver seat harness, 5 cm from x319 breakout)
• J314 (passenger seat harness, 5 cm from x319 breakout)
• J317 (passenger heater element harness)
• J318 (passenger heater element harness)
• J321 (driver heater element harness)
• J322 (driver heater element harness)
• J409 (w/ trailer connector) (trailer accessory harness, between left rear tail lamp connector & trailer lighting connector)
• J901 (license lamp harness, 24 cm from x400 breakout)
• Jx105
• Jx106
• Left back-up lamp
• Left cargo lamp
• Left center high mounted stop lamp (chmsl)
• Left front fog lamp
• Left front park lamp
• Left license lamp
• Left park/turn signal lamp
• Left rear turn signal lamp
• Left stop- lamp
• Left tail lamp
• Nca
• Passenger back heated seat element
• Passenger cushion heated seat element
• Passenger heated seat control module
• Passenger seat adjuster switch
• Passenger seat lumbar adjuster switch
• Right back-up lamp
• Right cargo lamp
• Right center high mounted stop lamp (chmsl)
• Right front fog lamp
• Right front park lamp
• Right license lamp
• Right park/turn signal lamp
• Right rear turn signal lamp
• Right rear window switch
• Right stop- lamp
• Right tail lamp
• Trailer lighting converter
• Transfer case shift control module
• Underhood fuse block (left front side of engine compt)
• W/ driver power seat
• W/ passenger power seat
• W/ trailer connector
• X1 h

Ground Distribution Wiring Diagram (3 of 3) for GMC Canyon 2008

List of elements for Ground Distribution Wiring Diagram (3 of 3) for GMC Canyon 2008:

• (between front seats, under console)
• (if equipped) inside rearview mirror
• (if equipped) trailer connector
• Accessory switch
• Automatic transmission shift lock control solenoid
• B10
• Body control module (bcm)
• Crew cab
• Data link connector (dlc)
• Digital radio receiver
• Driver door jamb switch
• Evaporator temperature sensor
• From jx106 b (diagram 3 of 3)
• G300 (under driver seat carpet)
• G301 (under front passenger seat carpet)
• G302
• G400
• Hazard switch
• Headlamp dimmer switch
• Hvac control module
• I/p accessory power outlet 1
• I/p accessory power outlet 2
• If equipped
• Inflatable restraint front passenger presence system (pps) module
• Inflatable restraint sensing & diagnostic module (sdm)
• Instrument panel cluster (ipc)
• J200 (i/p harness, 6 cm from instrument cluster breakout)
• J201 (i/p harness, 7 cm from x204 breakout)
• J324
• Jx106
• Left rear door jamb switch
• Manual a/c
• Passenger door jamb switch
• Passenger seat belt buckle
• Pnk
• Radio
• Right rear door jamb switch
• Turn signal/ multifunction switch
• Vehicle communication interface module (vcim)
• W/ onstar
• X1 a12
• X1 b3

HEADLIGHTS

Headlights Wiring Diagram for GMC Canyon 2008

List of elements for Headlights Wiring Diagram for GMC Canyon 2008:

• A10
• A11
• A18
• A31
• A36
• A37
• A39
• A43
• Ambient light sensor (upper right side of dash, at windshield)
• Ambient lt sens
• Auto
• B10
• Beam sel relay
• Bm sel rly ctrl
• Body control module (bcm) (behind right kick panel)
• Class 2 data
• Class 2 ser data
• Class 2 serial data
• Computer data lines system
• Drl fuse 10a
• Drl ind
• Drl relay
• Drl relay ctrl
• Flash to pass
• Fog lmp ind
• Fog lp rly ctrl
• Fog lp sw sig
• Fog/ lamp relay
• Fog/lamp fuse 15a
• Front fog lamp ind
• Front fog lamp switch
• G105
• G106
• Ground distribution system
• Hdlp dim sw sig
• Hdlp off sig
• Hdlp on sig
• Hdlp relay
• Hdlp rly ctrl
• Head
• Headlamp & panel dimmer switch
• Headlamp dimmer switch
• High beam
• High beam ind
• Hot at all times
• Ign
• Instrument panel cluster (ipc)
• J200
• Jx105 (left side of engine compt)
• Jx106 (right side of engine compt)
• Left front fog lamp
• Left high beam head- lamp
• Left low beam head- lamp
• Low ref
• Lt hdlp fuse 10a
• Off
• Park
• Park brake switch (lower left end of dash)
• Pk brake sig
• Pnk
• Red
• Right front fog lamp
• Right high beam head- lamp
• Right low beam head- lamp
• Rt hdlp fuse 10a
• Turn signal/ multifunction switch
• Underhood fuse block (left front side of engine compt)
• X1 c2
• X7 c10

HORN

Horn Wiring Diagram for GMC Canyon 2008

List of elements for Horn Wiring Diagram for GMC Canyon 2008:

• A25
• A40
• A5 x7
• B11
• Body control module (bcm) (behind right kick panel)
• F1 x1
• G105
• Ground distribution system
• Horn
• Horn fuse 10a
• Horn relay
• Horn rly ctrl
• Horn switch
• Hot at all times
• Inflatable restraint steering wheel module coil
• Jx105 (left side of engine compt)
• Nca
• Underhood fuse block (left front side of engine compt)
• X204

INSTRUMENT CLUSTER

Instrument Cluster Wiring Diagram for GMC Canyon 2008

List of elements for Instrument Cluster Wiring Diagram for GMC Canyon 2008:

• (chassis harness, 39 cm before fuel pump & sender assembly)
• (or tan)
• (right rear of engine compt) engine control module (ecm)
• (under driver seat carpet) g300
• A19
• A31
• A38
• A39
• A41
• A42
• A44
• A45
• A47
• Abs ind
• Air bag ind
• Battery
• Body control module (bcm) (behind right kick panel)
• Brake fluid level switch (on brake fluid reservoir)
• Brake ind
• Brk fluid lvl
• Chime
• Class 2
• Clstr fuse 10a
• Computer data lines system
• Cruise ind
• Dr belt sw
• Driver seat belt buckle (right side of driver's seat)
• Driver seat belt switch
• Drl ind
• Ect sens
• Engine controls system
• Engine coolant
• Engine coolant temperature gauge
• Engine oil pressure (eop) switch
• Fuel gauge
• Fuel level
• Fuel pump & sender assembly (top of fuel tank)
• G105
• Ground
• High beam ind
• Hot at all times
• Ign
• Illumination (4 bulbs)
• Inflatable restraint sensing & diagnostic module (beneath center console)
• Instrument panel cluster (ipc)
• J201
• J310
• J311 (body harness, 24.5 cm from g302 breakout)
• Jx105 (left side of engine compt)
• L turn ind
• Left turn ind
• Low engine oil pressure gauge
• Low engine oil pressure ind
• Low ref
• Malfunction ind
• Mil ctrl
• Nca
• Oil press
• Park brake switch (lower left end of dash)
• Pnk
• Prk brk sw
• R turn ind
• Right turn ind
• Seat belt ind
• Security ind
• Serial data
• Speedometer
• Tachometer
• Temperature (ect) sensor (on left rear of engine)
• Underhood fuse block (left front side of engine compt)
• Up shift ind
• Volts

INTERIOR LIGHTS

Courtesy Lamps Wiring Diagram for GMC Canyon 2008

List of elements for Courtesy Lamps Wiring Diagram for GMC Canyon 2008:

• (in left "b" pillar)
• (in right "b" pillar)
• A10
• A11
• A12
• A13
• A30
• A32
• A38
• A39
• A40
• A41
• A44
• A46
• A47
• Batt
• Body control module (bcm) (behind right kick panel)
• Cargo lamp switch
• Cargo lp sw
• Courtesy lps
• Crew cab
• Dome lamp
• Dome on switch
• Dome override switch
• Driver door jamb switch
• Front passenger door jamb switch
• G105
• G300 (under driver seat carpet)
• G301 (under front passenger seat carpet)
• Headlamp & panel dimmer switch
• Hot at all times
• J304
• Jx105 (left side of engine compt)
• Left cargo lamp
• Left center high mounted stop lamp (chmsl)
• Left i/p courtesy lamp
• Left rear door jamb switch (in left "c" pillar)
• Lf door ajar
• Low ctrl
• Low ref
• Lp sw sig
• Lr door ajar
• Override sw
• Rf door ajar
• Right cargo lamp
• Right center high mounted stop lamp (chmsl)
• Right i/p courtesy lamp
• Right rear door jamb switch (in right "c" pillar)
• Rr door ajar
• Tbc fuse 10a
• Trn/hazrd frt fuse 15a
• Underhood fuse block (left front side of engine compt)
• W/ premium lighting

Instrument Illumination Wiring Diagram for GMC Canyon 2008

List of elements for Instrument Illumination Wiring Diagram for GMC Canyon 2008:

• (3 bulbs)
• (5 bulbs)
• 2wd
• 4wd
• A10
• A24
• A28
• A29
• A35
• A36
• A39
• A48
• Accessory switch
• Auto
• Battery
• Body control module (bcm) (behind right kick panel)
• C11
• Computer data lines system
• Crew cab
• Dim control
• Dim sw sig
• Driver door lock/ window switch
• F11
• Frt prk lamp fuse 10a
• G105
• G106
• Hazard switch
• Head
• Headlamp & panel dimmer switch
• Hot at all times
• Hvac control module
• Illum
• Illumi- nation (4 bulbs)
• Instrument panel cluster
• Instrument panel lamps dimming control
• J200
• J500
• Jx105 (left side of engine compt)
• Jx106 (right side of engine compt)
• Left rear window switch
• Logic
• Low ref
• Lp rly ctrl
• Off
• Outside rearview mirror switch
• Park
• Parklamp sig
• Passenger door lock/ window switch
• Pk lp ctrl
• Prk/lamp relay
• Rear prk lamp 2 fuse 10a
• Right rear window switch
• Serial data
• Tbc fuse 10a
• Underhood fuse block (left front side of engine compt)
• W/ driver convenience iii sales package
• W/ dual folding power mirrors
• W/ onstar
• W/o onstar
• X2 vehicle communication interface module (vcim) (right side of dash)

POWER DISTRIBUTION

Power Distribution Wiring Diagram (1 of 4) for GMC Canyon 2008

List of elements for Power Distribution Wiring Diagram (1 of 4) for GMC Canyon 2008:

• (body harness, 4 cm from accelerator pedal position switch breakout)
• (left front side of engine compt) underhood fuse block
• (passenger heater element harness) j319
• (right side of engine compt) jx106
• 4wd
• A/c fuse 10a
• A/t
• A10
• Abs 1 fuse 30a
• Abs 2 fuse 40a
• Aux pwr 1 fuse 20a
• Aux pwr 2 fuse 20a
• B10
• B11
• Battery
• Blower motor
• Blwr fuse 30a
• Body control module (bcm)
• California
• Clstr fuse 10a
• Cnstr vent fuse 10a
• Crew cab w/ power windows
• Data link connector (dlc)
• Digital radio receiver
• Diode
• Dr/lck fuse 20a
• Driver door lock/ window switch
• Driver heated seat module
• Driver seat lumbar adjuster switch
• E11
• Ecm b fuse 10a
• Electronic brake control module (ebcm)
• Engine control module (ecm)
• Evaporative emission (evap) canister vent solenoid valve
• F12
• From a aux pwr 1 fuse (diagram 1 of 4)
• From b trn/hazrd rear fuse (diagram 1 of 4)
• Fusible link 1
• G106
• Generator
• Htd/seat fuse 20a
• Hvac control module
• I/p 1 accessory power outlet
• I/p 2 accessory power outlet
• If equipped
• Ign 3 hvac relay
• Instrument panel cluster (ipc)
• J200
• J302
• J313 (passenger seat harness, 12.5 cm from x318 breakout)
• J315 (driver heater element harness)
• Left rear window switch
• Mega fuse 100a
• Nca
• Onstar fuse 10a
• Passenger door lock/ window switch
• Passenger heated seat module
• Passenger seat lumbar adjuster switch
• Pwr/ wndw fuse 30a
• Radio
• Rap relay
• Rdo fuse 15a
• Red
• Regular, extended cab w/ power windows
• Right rear window switch
• S/roof fuse 20a
• Secondary air injection (air) pump fuse block
• Starter
• Stop fuse 20a
• Stop lamp switch
• Strt relay
• Strtr fuse 30a
• Sunroof switch
• Tbc fuse 10a
• Tccm fuse 10a
• Tcm fuse 10a
• To dr/lck fuse (diagram 1 of 4)
• To pwr/trn relay (diagram 2 of 4)
• To rap relay (diagram 1 of 4)
• Transfer case shift control module
• Transmission control module (tcm)
• Trn/ hazrd frt fuse 15a
• Trn/ hazrd rear fuse 15a
• Turn signal/ multi- function switch
• Underhood fuse block (left front side of engine compt)
• Vehicle communication interface module (vcim)
• W/ accessory electrical receptacle
• W/ driver power seat adjuster
• W/ electric side door lock control
• W/ gps 1
• W/ passenger power seat adjuster
• Windshield wiper/washer switch
• Wpr fuse 25a
• Wpr relay
• Wsw fuse 10a
• X204

Power Distribution Wiring Diagram (2 of 4) for GMC Canyon 2008

List of elements for Power Distribution Wiring Diagram (2 of 4) for GMC Canyon 2008:

• (automatic transmission harness) j133
• (driver seat harness, 12.5 cm from x319 breakout) j312
• (not used)
• 1-2 shift solenoid (ss) valve
• 2-3 shift solenoid (ss) valve
• 20a
• 3-2 shift solenoid (ss) valve
• 4wd
• A/t
• Accessory switch
• Air bag fuse 10a
• Cruise control release switch
• Cruise fuse 10a
• Driver seat adjuster switch
• Driver seat lumbar adjuster switch
• Drl fuse 10a
• Drl relay
• Fog/ lamp relay
• Fog/lamp fuse 15a
• From body control module (bcm) (diagram 4 of 4)
• From fuel/ d pump relay (diagram 2 of 4)
• From wpr c fuse (diagram 1 of 4)
• Fuel/ pump relay
• G105
• Generator battery control module
• Hdlp relay
• Horn fuse 10a
• Horn relay
• Inflatable restraint front passenger presence system (pps) module
• Inflatable restraint sensing & diagnostic module (sdm)
• Inside rearview mirror
• Jx105 (left side of engine compt)
• M/t
• Nca
• Passenger seat adjuster switch
• Pnk
• Power seat fuse holder
• Pwr/seat fuse 40a
• Pwr/trn relay
• Red
• Run/ crnk relay
• Rvc fuse 10a
• To bck/up fuse (diagram 3 of 4)
• To ign trans d fuse (diagram 4 of 4)
• To run/ crank relay (diagram 2 of 4)
• Torque converter clutch (tcc) pulse width modulation (pwm) solenoid valve
• Torque converter clutch (tcc) solenoid valve
• Trans fuse 10a
• Transfer case shift control module
• Transmission control module (tcm)
• Turn signal/ multi-fuction switch
• Underhood fuse block (left front side of engine compt)
• W/ power seats
• W/o outside display w/ outside display
• X204
• X6 b3

Power Distribution Wiring Diagram (3 of 4) for GMC Canyon 2008

List of elements for Power Distribution Wiring Diagram (3 of 4) for GMC Canyon 2008:

• (fuel injector harness, 4 cm from fuel injector 4 breakout) j104
• (fuel injector harness, 5 cm from fuel injector 4 breakout) j103
• (not used)
• 2.9l
• 3.7l
• 4wd
• A/c relay
• A/t
• Abs fuse 10a
• Back-up lamp switch
• Bck/up fuse 15a
• California
• Electronic brake control module (ebcm)
• Engine control module (ecm)
• Erls fuse 15a
• Evaporative emission (evap) canister purge solenoid valve
• From e trans fuse (diagram 2 of 4)
• From ign g fuse (diagram 3 of 4)
• Front drive axle actuator
• Frt/axl fuse 15a
• Fuel injector
• Ign fuse 15a
• Ignition coil/ module 1
• Ignition coil/ module 2
• Ignition coil/ module 3
• Ignition coil/ module 4
• Ignition coil/ module 5
• Inj fuse 15a
• Longitudinal accelerometer sensor
• M/t
• Mass air flow (maf)/ intake air temperature (iat) sensor
• Park/ neutral position (pnp) switch
• Pcm i fuse 10a
• Pnk
• Secondary air injection (air) pump relay
• To erls fuse (diagram 3 of 4)
• Underhood fuse block (left front side of engine compt)
• X2 b2
• X2 c3
• X2 f4
• X7 f3

Power Distribution Wiring Diagram (4 of 4) for GMC Canyon 2008

List of elements for Power Distribution Wiring Diagram (4 of 4) for GMC Canyon 2008:

• (chassis harness, 40.5 cm from fuel pump & sender assembly breakout) j400
• 5 volt
• A/c cmprsr 10a
• A/c relay
• A/t
• A14
• A24
• Acc
• Accessory switch
• Body control module (bcm)
• C11
• Crew cab w/ power window
• Driver door lock/ window switch
• Engine control module (ecm)
• F11
• From f run/ crank relay (diagram 2 of 4)
• Frt prk lamp fuse 10a
• G x403
• Ign
• Ign transd fuse 10a
• Ignition switch
• Ignition volt
• J900 (license lamp harness, 44.5 cm before right license lamp)
• Left front marker lamp
• Left license lamp
• Left park/turn signal lamp
• Left rear turn signal lamp
• Left rear window switch
• Left stop lamp
• Nca
• Off
• Outside rearview mirror switch (if equipped)
• Passenger door lock/ window switch
• Prk/lamp relay
• Rear prk lamp 2 fuse 10a
• Rear prk lamp fuse 15a
• Right front marker lamp
• Right license lamp
• Right park/turn signal lamp
• Right rear turn signal lamp
• Right rear window switch
• Right stop lamp
• Run
• Start
• To run/crank relay (diagram 2 of 4)
• Trailer lighting converter
• Transmission control module (tcm)
• Underhood fuse block (left front side of engine compt)
• W/ power window
• X1 a48
• X2 a42

POWER DOOR LOCKS

Power Door Locks Wiring Diagram for GMC Canyon 2008

List of elements for Power Door Locks Wiring Diagram for GMC Canyon 2008:

• (body harness, 10.5 cm from accelerator pedal position switch breakout)
• (body harness, 17 cm from accelerator pedal position switch breakout)
• (not used)
• 87a
• A11
• A12
• A38
• A39
• A41
• A42
• A44
• A47
• All doors lock ctrl
• All doors unlock ctrl
• Battery +
• Body control module (bcm) (behind right kick panel)
• Class 2 serial data
• Computer data lines system
• Door unlock
• Door unlock ctrl
• Dr/lck fuse 20a
• Driver door lock actuator (in lower rear of door)
• Driver door lock/window switch
• Driver door unlock ctrl
• Driver unlock relay
• F5 x6
• Front passenger door lock actuator (in lower rear of door)
• G105
• G106
• G301 (under front passenger seat carpet)
• Ground
• Hot at all times
• J304
• J308
• J309
• J500
• Jx105 (left side of engine compt)
• Jx106 (right side of engine compt)
• Left rear door lock actuator (in lower rear of door)
• Lock relay
• Lock sw
• Lock switch
• Pass door lock ctrl
• Passenger door lock/ window switch
• Right rear door lock actuator (in lower rear of door)
• Tan
• Tbc fuse 10a
• Trn/ hazrd frt fuse 15a
• Trn/ hazrd rear fuse 15a
• Underhood fuse block (left front side of engine compt)
• Unlock relay
• Unlock sw
• Unlock switch
• W/ crew cab
• W/o crew cab
• X7 b3

POWER MIRRORS

Automatic Day/Night Mirror Wiring Diagram for GMC Canyon 2008

List of elements for Automatic Day/Night Mirror Wiring Diagram for GMC Canyon 2008:

• Ambient air temperature sensor (w/ dual reading lamps) (on radiator support, behind center of grille)
• B5 x6
• Button back- lighting
• Cruise fuse 10a
• Drain wire
• Emergency
• Emergency ind
• Exterior lights system
• G105
• Hot at all times
• Hot in run or start
• Inside rearview mirror
• Jx105 (left side of engine compt)
• Keypad ctrl
• Keypad green led ind
• Keypad green led sig
• Keypad red led ind
• Keypad red led sig
• Keypad signal
• Microphone
• Microphone sig
• Nca
• Onstar
• Onstar ind
• Onstar keypad
• Phone
• Phone ind
• Pnk
• Run/ crnk relay
• Underhood fuse block (left front side of engine compt)
• Vehicle communication interface module (vcim) (right side of dash)
• W/ onstar
• W/o onstar

Power Mirrors Wiring Diagram for GMC Canyon 2008

List of elements for Power Mirrors Wiring Diagram for GMC Canyon 2008:

• A29
• Body control module (behind right kick panel)
• Courtesy lamps ctrl
• Driver outside rearview mirror
• G105
• Horiz
• Hot at all times
• Interior lights system
• J500
• Jx105 (left side of engine compt)
• Left
• Nca
• Off
• Outside rearview mirror switch
• Passenger outside rearview mirror
• Right
• Trn/hazrd frt fuse 15a
• Underhood fuse block (left front side of engine compt)
• Vert

POWER SEATS

Driver Heated Seat Wiring Diagram for GMC Canyon 2008

List of elements for Driver Heated Seat Wiring Diagram for GMC Canyon 2008:

• (driver heater element harness)
• (driver heater element harness) j315
• A/c fuse 10a
• A26
• A5 x6
• B nca
• Body control module (bcm) (behind right kick panel)
• C nca
• Driver back heated seat element
• Driver cushion heated seat element
• Driver heated seat control module
• Driver seat lumbar adjuster switch
• E nca
• E9 x7
• F10
• G106
• Gnd
• High
• High/low status ind bulb
• Hot at all times
• Htd/seat fuse 20a
• Ign 3 hvac relay
• Ign 3 voltage
• J300
• J306
• J320
• J321 (driver heater element harness)
• J322
• Jx106 (right side of engine compt)
• Low
• Nca
• Pnk
• Red
• Underhood fuse block (left front side of engine compt)
• W/ driver power seat adjuster
• W/ driver power seat adjuster red

Driver Power Seat Wiring Diagram for GMC Canyon 2008

List of elements for Driver Power Seat Wiring Diagram for GMC Canyon 2008:

• 20a
• Driver seat adjuster motor assembly
• Driver seat adjuster switch
• Driver seat vertical motor
• Front vertical
• Fuse holder power seat
• Fwd
• G106
• Horiz- ontal
• Hot at all times
• J306
• J312
• Jx106 (right side of engine compt)
• Pwr/seat fuse 40a
• Rear vertical
• Rwd
• Tan
• Underhood fuse block (left front side of engine compartment)

Lumbar Wiring Diagram for GMC Canyon 2008

List of elements for Lumbar Wiring Diagram for GMC Canyon 2008:

• 20a
• Driver seat lumbar adjuster switch
• Driver seat lumbar motor
• Fuse holder power seat
• G106
• Hot at all times
• Htd/seat fuse 20a
• J306
• J312
• J313
• J314
• Jx106 (right side of engine compt)
• Nca
• Out
• Passenger seat lumbar adjuster switch
• Passenger seat lumbar motor
• Pnk
• Power seat adjuster
• Pwr/seat fuse 40a
• Underhood fuse block (left front side of engine compt)

Passenger Power Seat Wiring Diagram for GMC Canyon 2008

List of elements for Passenger Power Seat Wiring Diagram for GMC Canyon 2008:

• 20a
• Front vertical
• Fuse holder power seat
• Fwd
• G106
• Horiz- ontal
• Hot at all times
• J312
• J314
• Jx106 (right side of engine compt)
• Passenger seat adjuster motor assembly
• Passenger seat adjuster switch
• Pwr/seat fuse 40a
• Rear vertical
• Rwd
• Tan
• Underhood fuse block (left front side of engine compartment)

Passenger"s Heated Seat Wiring Diagram for GMC Canyon 2008

List of elements for Passenger"s Heated Seat Wiring Diagram for GMC Canyon 2008:

• (passenger heater element harness)
• (passenger heater element harness) j319
• A/c fuse 10a
• A26
• A5 x6
• B nca
• Body control module (bcm) (behind right kick panel)
• C nca
• D nca
• E nca
• E9 x7
• F10
• G106
• Gnd
• High
• High/low status ind bulb
• Hot at all times
• Htd/seat fuse 20a
• Ign 3
• Ign 3 hvac relay
• Ign 3 voltage
• J300
• J313
• J314
• J316
• J317 (passenger heater element harness)
• J318
• Jx106 (right side of engine compt)
• Logic
• Low
• Nca
• Passenger cushion heated seat element
• Passenger seat back heater element
• Passenger seat cushion heater element
• Passenger seat lumbar adjuster switch
• Pnk
• Red
• Rt seat belt sw
• Underhood fuse block (left front side of engine compt)
• W/ passenger power seat adjuster

POWER TOP/SUNROOF

Power Top/Sunroof Wiring Diagram for GMC Canyon 2008

List of elements for Power Top/Sunroof Wiring Diagram for GMC Canyon 2008:

• A10
• Body control module (behind right kick panel)
• Closed
• F12
• G303
• Hot at all times
• Nca
• Open
• Rap relay
• Rap rly
• Red
• Sunroof fuse 20a
• Sunroof motor (center front of headliner)
• Sunroof switch
• Underhood fuse block (left front side of engine compt)

POWER WINDOWS

Power Windows Wiring Diagram, 2 Door for GMC Canyon 2008

List of elements for Power Windows Wiring Diagram, 2 Door for GMC Canyon 2008:

• (not used)
• Auto
• Down
• Down relay
• Dr/lck fuse 20a
• Driver door lock/ window switch
• Driver window motor (in lower front of door)
• Front passenger window motor (in lower front of door)
• G105
• G106
• Hot at all times
• Hot w/ rap relay energized
• J500
• Jx105 (left side of engine compt)
• Jx106 (right side of engine compt)
• Logic
• Passenger door lock/ window switch
• Pwr/ wndw fuse 30a
• Rf down
• Rf up
• Tan
• Underhood fuse block (left front side of engine compt)
• Up relay
• X6 f5

Power Windows Wiring Diagram, 4 Door for GMC Canyon 2008

List of elements for Power Windows Wiring Diagram, 4 Door for GMC Canyon 2008:

• (body harness, 4 cm from accelerator pedal position breakout) j307
• Auto
• Down
• Down relay
• Dr/lck fuse 20a
• Driver door lock/ window switch
• Driver window motor (in lower front of door)
• Dwn
• Front passenger window motor (in lower front of door)
• G105
• G106
• Hot at all times
• Hot w/ rap relay energized
• J302
• J500
• Jx105 (left side of engine compartment)
• Jx105 (left side of engine compt)
• Jx106 (right side of engine compartment)
• Jx106 (right side of engine compt)
• Left rear window motor (in lower center of door)
• Left rear window switch
• Logic
• Lr down
• Lr up
• Passenger door lock/ window switch
• Pwr/ wndw fuse 30a
• Rf down
• Rf up
• Right rear window motor (in lower center of door)
• Right rear window switch
• Rr down
• Rr up
• Tan
• Underhood fuse block (left front side of engine compt)
• Up relay
• W/l
• X4 a
• X6 f5

RADIO

Radio Wiring Diagram for GMC Canyon 2008

List of elements for Radio Wiring Diagram for GMC Canyon 2008:

• A10
• A11
• A12
• Audio comm sig
• B10
• B11
• B12
• Bare
• Coax
• Common sig
• Computer data lines system
• Digital radio antenna
• Digital radio receiver (if equipped) (center of dash)
• Drain wire
• G300 (under driver seat carpet)
• Ground
• Hot at all times
• J201
• Left aud sig
• Left audio sig
• Left front speaker
• Left front tweeter speaker (w/ 6 speakers system)
• Left rear speaker (w/ extended crew cab)
• Lf out +
• Lf out -
• Lr out +
• Lr out -
• Radio
• Radio antenna
• Rdo fuse 15a
• Rf out +
• Rf out -
• Right aud sig
• Right front speaker
• Right front tweeter speaker (w/ 6 speakers system)
• Right rear speaker (w/ extended crew cab)
• Rr out +
• Rr out -
• Satellite in
• Serial data
• Tan
• Underhood fuse block (left front side of engine compartment)
• Vehicle communication interface module (vcim) (w/ onstar) (right side of dash)

SHIFT INTERLOCK

Shift Interlock Wiring Diagram for GMC Canyon 2008

List of elements for Shift Interlock Wiring Diagram for GMC Canyon 2008:

• A/t shift lock control solenoid (under center console, left side of shifter)
• A11 x7
• A31 x2
• A47 x1
• B2 x7
• Body control module (behind right kick panel)
• Btsi
• Computer data lines system
• Engine control module
• G106
• Hot at all times
• J100 (body harness, 14.5 cm from accelerator pedal position switch breakout)
• J200
• Jx106 (right side of engine compt)
• Logic
• Park/neutral position switch
• Serial data
• Stop fuse 20a
• Stop lamp switch
• Tan
• Tbc fuse 10a
• Transmission control module
• Underhood fuse block (left front side of engine compt)
• X1 a7

STARTING/CHARGING

Charging Wiring Diagram for GMC Canyon 2008

List of elements for Charging Wiring Diagram for GMC Canyon 2008:

• (right rear of engine compt) engine control module (ecm)
• A11
• B11
• Batt pos volt
• Battery
• Computer data lines system
• Driver information center (dic) display
• Field duty cyc
• G100 (next to rear side of battery)
• G102 (lower left side of engine)
• G104 (left side of engine)
• Gen reg cntrl
• Gen turn on
• Generator
• Generator battery control module (left front of engine compt, near battery)
• Ground
• Instrument panel cluster (ipc)
• J106
• Logic
• Mega fuse 100a
• Red
• Rvc fuse 10a
• Serial data
• Starter
• Underhood fuse block (left front side of engine compt)
• Used) (not
• Volts

Starting Wiring Diagram, A/T for GMC Canyon 2008

List of elements for Starting Wiring Diagram, A/T for GMC Canyon 2008:

• A14
• A42
• A42 key resistor sig
• A47
• Acc
• B11
• Battery
• Body control module (bcm) (behind right kick panel)
• C11
• Computer data lines system
• Engine control module (ecm) (right rear of engine compt)
• G100 (next to rear side of battery)
• G102 (lower left side of engine)
• G104 (left side of engine)
• Ign volt x2
• Ignition switch
• J110
• Off
• P/n
• Park neutral position switch (on lower left side of transmission)
• Pnp start
• Red
• Run
• Serial
• Serial data
• Serial data x1
• Start
• Starter
• Strtr fuse 30a
• Strtr relay
• Underhood fuse block (left front side of engine compt)
• X1 ctrl rly
• X1 data
• X3 sw

Starting Wiring Diagram, M/T for GMC Canyon 2008

List of elements for Starting Wiring Diagram, M/T for GMC Canyon 2008:

• 5v ref
• Acc
• B11
• Battery
• Body control module (bcm) (behind right kick panel)
• C11
• Clutch pedal position (cpp) sensor
• Cpp sig
• G100 (next to rear side of battery)
• G102 (lower left side of engine)
• G104 (left side of engine)
• G105
• Ign trnsd fuse 10a
• Ign volt
• Ignition switch
• J203
• Jx105 (left side of engine compt)
• Low ref
• Off
• Pcm 1 fuse 10a
• Pnk
• Red
• Rly
• Run
• Run/crank relay
• Start
• Starter
• Strtr fuse 30a
• Strtr relay
• Underhood fuse block (left front side of engine compt)
• X1 ctrl engine control module (ecm) (right rear of engine compt)

SUPPLEMENTAL RESTRAINTS

Supplemental Restraints Wiring Diagram (1 of 2) for GMC Canyon 2008

List of elements for Supplemental Restraints Wiring Diagram (1 of 2) for GMC Canyon 2008:

• A2 x275
• Accessory switch
• Air bag fuse 10a
• Computer data lines system
• Control
• Cruise fuse 10a
• Disbl sw signal
• G302 (between front seats, under console)
• Ground
• High control
• Hot w/ park lamp relay energized
• Hot w/ run/crank relay energized
• Ignition 1
• Inflatable restraint i/p module (right side of dash)
• Inflatable restraint passenger air bag on/off indicator
• Inflatable restraint sensing & diagnostic module (sdm) (beneath center console)
• Inflatable restraint steering wheel module (top of steering wheel)
• Inflatable restraint steering wheel module coil
• J324
• Left front seat belt pretensioner (extended cab: in left rear door) (regular/crew cab: in left "b" pillar)
• Low control
• Low reference
• Nca
• Passenger seat belt indicator
• Pnk
• Power distribution system
• Red
• Right front seat belt pretensioner (extended cab: in right rear door) (regular/crew cab: in right "b" pillar)
• Rr pk lp2 fuse 10a
• Seat belt sw
• Serial data
• Shorting bar
• Shorting clip
• Signal
• Stage 1
• Stage 2
• Tan
• Underhood fuse block (left front side of engine compartment)
• Voltage

Supplemental Restraints Wiring Diagram (2 of 2) for GMC Canyon 2008

List of elements for Supplemental Restraints Wiring Diagram (2 of 2) for GMC Canyon 2008:

• (between front seats, under console) g302
• (right side of dash) vehicle communication interface module (vcim)
• A38
• A39
• A42
• Air bag ind
• Body control module (behind right kick panel)
• Data link connector (dlc) (lower left side of dash)
• Driver seat belt buckle (right side of driver's seat)
• Driver seat belt switch
• G302 (between front seats, under console)
• Gnd
• Ign
• Ign 1+
• Inflatable restraint front passenger presence system (pps) module (under side of front passenger seat)
• Inflatable restraint passenger presence system (pps) sensor (in front passenger seat cushion)
• Instrument panel cluster
• Ipc class 2 serial data
• J311 (body harness, 24.5 cm from g302 breakout)
• J323
• J324
• Left inflatable restraint front end sensor (on left underside of front frame crossmember)
• Left inflatable restraint roof rail module (if equipped) (in roof above driver door)
• Left inflatable restraint seat position sensor (on driver seat track)
• Left inflatable restraint side impact sensor (sis) (if equipped) (lower rear of driver door)
• Logic
• Low ref
• Nca
• Nca a
• Off ind
• On ind
• Passenger seat belt buckle (under passenger's seat)
• Passenger seat lumbar adjuster/ heater switch
• Pnk
• Press sig
• Red
• Right inflatable restraint front end sensor (on right underside of front frame crossmember)
• Right inflatable restraint roof rail module (if equipped) (in roof above front passenger door)
• Right inflatable restraint seat position sensor (on front passenger seat track)
• Right inflatable restraint side impact sensor (sis) (if equipped) (lower rear of front passenger door)
• Seat belt ind control
• Serial
• Shorting bar
• Shorting clip
• Tan
• Tension sig
• Volt ref
• W/ power seats
• W/ vehicle communication interface module
• W/o power seats
• W/o vehicle communication interface module

TRANSMISSION

A/T Wiring Diagram for GMC Canyon 2008

List of elements for A/T Wiring Diagram for GMC Canyon 2008:

• 1-2 shift sol ctrl
• 1-2 shift solenoid (ss) valve
• 2-3 shift sol ctrl
• 2-3 shift solenoid (ss) valve
• 3-2 shift sol ctrl
• 3-2 shift solenoid (ss) valve
• Acc
• Automatic transmission
• Automatic transmission fluid pressure manual valve position switch
• Automatic transmission fluid temperature (tft) sensor
• Body control module (bcm) (behind right kick panel)
• Computer data lines system
• Engine control module (ecm) (right rear of engine compt)
• Exterior lights system
• G102 (lower left side of engine)
• Gnd
• Hi spd serial data +
• Hi spd serial data -
• Hot at all times
• Hot w/ run/ crank relay energized
• Ign volt
• Ignition switch
• In shaft spd sens
• Input speed sensor (iss)
• J110
• J133
• J204
• Lo ref
• Off
• P/n
• Park/neutral position (pnp) switch (on lower left side of transmission)
• Pc sol valve hi ctrl
• Pc sol valve lo ctrl
• Pnk
• Pnp/clutch start sw sig
• Power distribution system
• Pressure control (pc) solenoid valve
• Red
• Rev
• Run
• Start
• Stop lamp ctrl
• Tan
• Tcc pwm sol ctrl
• Tcc sol valve ctrl
• Tcm fuse 10a
• Tft sens sig
• Torque converter clutch (tcc) pulse width modulation (pwm) solenoid valve
• Torque converter clutch (tcc) solenoid valve
• Trans fluid sw a
• Trans fluid sw b
• Trans fluid sw c
• Trans fuse 10a
• Trans range sw a
• Trans range sw b
• Trans range sw c
• Trans range sw p
• Transmission control module (tcm)
• Underhood fuse block (left front side of engine compt)
• Vehicle speed sensor (vss) (4wd: on left rear of transfer case) (2wd: left rear of transmission)
• Vss hi sig
• Vss lo sig

Transfer Case Wiring Diagram for GMC Canyon 2008

List of elements for Transfer Case Wiring Diagram for GMC Canyon 2008:

• (lower left side of engine) g103
• (not used) d
• 12v
• 2 hi
• 2 hi ind
• 2wd/4wd sig
• 4 hi
• 4 hi ind
• 4 lo
• 4 lo ind
• 4 lo sw sig
• 5v ref
• A encoder sig
• A sig
• Accessory switch
• Axle act ctrl
• Axle sw sig
• B encoder sig
• B sig
• B2 x2
• Bat
• Body control module (bcm) (behind right kick panel)
• C encoder sig
• C sig
• Computer data lines system
• Cruise fuse 10a
• Encoder motor
• Engine control module (ecm) (right rear of engine compt)
• F11
• Front axle actuator (on right center of front axle housing)
• Frt axl fuse 15a
• G105
• G106
• Gnd
• Ground
• Ground distribution system
• Hot at all times
• Hot in run or start
• Ign volt
• Ign voltage
• Interior lights system
• J200
• Jx105 (left side of engine compt)
• Jx106 (right side of engine compt)
• Lo sig
• Logic
• Mtr ctrl a
• Mtr ctrl b
• Neu ind ctrl
• Neu sw sig
• Neutral
• Neutral ind
• P encoder sig
• P sig
• Pnk
• Power distribution system
• Prk lp ctrl
• Prk/lamp relay
• Rear prk lamp 2 fuse 10a
• Red
• Rly ctrl
• Run/crank relay
• Serial data
• Sig hi
• Sig lo
• Sw sig lo
• Tan
• Tccm fuse 10a
• Transfer case 2/4 wheel driver indicator switch (lower right side of transfer case)
• Transfer case encoder motor (on rear of transfer case)
• Transfer case neutral switch (upper right side of transfer case)
• Transfer case shift control module (under driver seat carpet)
• Turn signal/ multi-function switch
• Underhood fuse block (left front side of engine compt)
• Vehicle speed sensor (m/t) (on left rear of transfer case)
• X1 a24
• X6 f1

WARNING SYSTEMS

Warning Systems Wiring Diagram for GMC Canyon 2008

List of elements for Warning Systems Wiring Diagram for GMC Canyon 2008:

• (body harness, 24.5 cm from g302 breakout) j311
• A10
• A14
• A31
• A32
• A38
• A39
• A42
• A44
• Auto
• Body control module (bcm) (behind right kick panel)
• Brake ind
• Chime
• Class 2 serial data
• Computer data lines system
• Driver door jamb switch (in left "b" pillar)
• Driver seat belt buckle (right side of driver's seat)
• Driver seat belt switch
• Front passenger door jamb switch (in right "b" pillar)
• G300 (under driver seat carpet)
• G301 (under front passenger seat carpet)
• G302 (between front seats, under console)
• Head
• Headlamp & panel dimmer switch
• Hot at all times
• Ign trans d fuse 10a
• Ign volt
• Ignition switch
• Inflatable restraint sensing & diagnostic module (sdm) (beneath center console)
• Instrument panel cluster (ipc)
• J303
• J304
• J323
• J324
• Key-in switch
• Left rear door jamb switch (crew cab) (in left "c" pillar)
• Left seat belt sw
• Left turn ind
• Lf dr ajar sw sig
• Logic
• Low ref
• Lr dr ajar sw sig
• Lr turn sig lmps ctrl
• Nca
• Off
• Park
• Park brake sw sig
• Park brake switch (lower left end of dash)
• Passenger seat belt buckle (left side of passenger's seat)
• Passenger seat belt switch
• Pk lmp rly ctrl
• Red
• Rf dr ajar sw sig
• Right rear door jamb switch (crew cab) (in right "c" pillar)
• Right seat belt sw
• Right turn ind
• Rr dr ajar sw sig
• Rr turn sig lmps ctrl
• Seat belt ind
• Seats system
• Tbc fuse 10a
• Underhood fuse block (left front side of engine compt)
• W/ power passenger seats
• X7 b2

WIPER/WASHER

Wiper/Washer Wiring Diagram for GMC Canyon 2008

List of elements for Wiper/Washer Wiring Diagram for GMC Canyon 2008:

• A20
• B10
• Body control module (behind right kick panel)
• F12
• G105
• Hi in
• Hot at all times
• Int
• Jx105 (left side of engine compt)
• Lo in
• Mist
• Nca
• Off
• Park out
• Rap relay
• Rap relay coil control
• Red
• Turn signal/ multi-function switch
• Underhood fuse block (left front side of engine compt)
• Windshield washer fluid pump (on washer fluid reservoir)
• Windshield washer pump control
• Windshield wiper motor (left rear of engine compt)
• Windshield wiper motor park switch signal
• Windshield wiper switch signal 1
• Windshield wiper switch signal 2
• Windshield wiper/ washer switch
• Wiper 2 relay
• Wiper relay
• Wpr fuse 25a
• Wsw fuse 10a
• X204