All Wiring Diagrams for Mitsubishi Pickup Mighty Max 1996 model

AIR CONDITIONING

A/C Wiring Diagram for Mitsubishi Pickup Mighty Max 1996

List of elements for A/C Wiring Diagram for Mitsubishi Pickup Mighty Max 1996:

• A/c compressor clutch (front left side of engine)
• A/c compressor clutch relay (left side of engine compartment)
• A/c controller (behind left side of dash)
• A/c engine coolant temperature switch (front of engine)
• A/c switch
• Blower motor
• Blower motor switch
• Capacitor
• Discharge gas temperature sensor (front left side of engine)
• Dual pressure switch (right front of engine compartment)
• Engine control module (right kick panel)
• Fuse 8 15a
• Fuse 9 20a
• Fuse block (right side of dash)
• Hot at all times
• Hot in run
• Hot in run and start
• Illum
• In-line fuse 10a
• Interior lights system
• Low pressure switch (right front of engine compartment)
• Nca
• Off
• Resistor (right side of dash)
• Thermistor (behind center of dash)

Heater Wiring Diagram for Mitsubishi Pickup Mighty Max 1996

List of elements for Heater Wiring Diagram for Mitsubishi Pickup Mighty Max 1996:

• 2.4l
• Blower motor
• Blower motor switch
• C 1995 vftc
• Capacitor
• Diode
• Engine control module
• Fuse 9 20a
• Fuse block (right side of dash)
• Hot in run
• Illum
• Interior lights system
• Nca
• Off
• Resistor (right side of dash)

ANTI-LOCK BRAKES

Anti-lock Brake Wiring Diagrams, Rear Wheel ABS for Mitsubishi Pickup Mighty Max 1996

List of elements for Anti-lock Brake Wiring Diagrams, Rear Wheel ABS for Mitsubishi Pickup Mighty Max 1996:

• (below left side of i/p)
• Data link connector (partial)
• Fuel pump
• Fuse 10a
• Fuse 15a
• Fuse block
• G sensor (under center of dash)
• G200 (left kick panel)
• G202 (left side of i/p)
• Hold valve
• Hot at all times
• Hot in run
• Hot in start and run
• Instrument cluster
• Modulator (center right side of vehicle)
• Rear abs warning ind
• Rear anti-lock brake system control unit (below center of dash)
• Red
• Release valve
• Speed sensor (rear right side of vehicle)
• Stop lamps
• Stop light switch (behind center of dash)

COMPUTER DATA LINES

Computer Data Lines for Mitsubishi Pickup Mighty Max 1996

List of elements for Computer Data Lines for Mitsubishi Pickup Mighty Max 1996:

• Automatic transmission control unit (behind left side of dash)
• Cruise control unit (left kick panel)
• D-03
• D-36
• Data link connector (below left side of dash)
• Data link connector (obd ii data) (below left side of dash)
• Engine control module (right side of dash)
• Fuse 1 10a
• Fuse block (lower left front of dash)
• G202 (left side of dash, near speedometer cable)
• Hot at all times
• Instrument cluster
• Rear anti-lock brake system control unit (below center of dash)
• Vss (reed switch)

CRUISE CONTROL

Cruise Control Wiring Diagram for Mitsubishi Pickup Mighty Max 1996

List of elements for Cruise Control Wiring Diagram for Mitsubishi Pickup Mighty Max 1996:

• 3.0l only
• Acc
• Actuator (rear right side of engine compartment)
• Battery
• Clutch pedal position switch (behind center of i/p)
• Cruise control switch (behind center of i/p)
• Cruise control unit (left kick panel)
• Data link connector (below left side of i/p)
• Engine control unit (behind right side of dash)
• Exterior lights system
• Fuse 3 10a
• Fuse 7 15a
• Fuse 8 15a
• Fuse block
• G106 (behind left headlight)
• G121 (center of safety wall)
• G202 (left side of i/p)
• Hot at all times
• Hot in start and run
• Ignition switch
• Instrument cluster
• Lock
• Main fusible link 60a
• Nca
• Red
• Run
• Start
• Starting system
• Stop light switch (behind center of i/p)
• Sub fusible link (left rear of engine compartment)
• Vacuum pump (rear right side of engine compartment)
• Vacuum pump relay (rear right side of engine compartment)
• Vacuum switch (rear right side of engine compartment)
• Vehicle speed sensor
• W/ abs
• Warning systems

ENGINE PERFORMANCE

2.4L

2.4L, Engine Performance Wiring Diagrams (1 of 2) for Mitsubishi Pickup Mighty Max 1996

List of elements for 2.4L, Engine Performance Wiring Diagrams (1 of 2) for Mitsubishi Pickup Mighty Max 1996:

• (right rear corner of engine compt)
• A/c engine coolant temperature switch
• A/c system
• A/t
• Air conditioning compressor clutch relay
• Coil wire
• Data link connector (left side of i/p)
• Diode
• Distributor firing order (1-3-4-2)
• Distributor signal generator
• Fuel injectors
• Fuel pump (in fuel tank)
• Fuel pump check terminal
• G111 (attached to battery tray)
• G121 (center of safety wall)
• G207 (behind dash, on top of steering column)
• Headlights system
• Ignition coil (top center of engine)
• Ignition power transistor (top center of engine)
• Ignition timing adjustment terminal (right rear corner of engine compt)
• M/t
• Multi-port fuel injection relay (below right side of dash, at kick panel)
• Pnk
• Power steering oil pressure switch (right front of engine)
• Powertrain control module (behind right kick panel)
• Pri
• Red
• Sec
• Starting system (starter relay)

2.4L, Engine Performance Wiring Diagrams (2 of 2) for Mitsubishi Pickup Mighty Max 1996

List of elements for 2.4L, Engine Performance Wiring Diagrams (2 of 2) for Mitsubishi Pickup Mighty Max 1996:

• (right side of engine compt, in air cleaner assembly)
• A/t only
• Acc
• Egr solenoid (left side of engine compartment)
• Engine coolant temperature sensor (front of engine)
• Evaporative emission purge solenoid (left side of engine compartment)
• Front heated oxygen sensor (under front of vehicle, in exhaust pipe)
• Fuse 10a
• Fuse 15a
• Fuse block
• Fusible link 2 20a
• G111 (attached to battery tray)
• G121 (center of safety wall)
• G203 (right kick panel)
• Hall ic
• Hot at all times
• Idle air control motor (top rear of engine, on throttle assembly)
• Idle sw
• Ignition switch
• Instrument cluster
• Lock
• Main fusible link
• Malfunction indicator (check engine)
• Manifold differential pressure sensor (left rear of engine)
• Nca
• Pnk
• Rear heated oxygen sensor (under center of vehicle, in exhaust pipe)
• Red
• Start
• Starting system (starter relay)
• Throttle position sensor (top center of engine)
• Vehicle speed sensor (reed switch)
• Volume air flow sensor

EXTERIOR LIGHTS

Back-up Lamps Wiring Diagram for Mitsubishi Pickup Mighty Max 1996

List of elements for Back-up Lamps Wiring Diagram for Mitsubishi Pickup Mighty Max 1996:

• (left i/p)
• A/t
• Back-up light
• Back-up light switch (on transmission)
• Fuse 8 15a
• Fuse block
• G106 (behind left headlight)
• G202 (left side of i/p)
• Hot in run or start
• Left rear combination light
• M/t
• Park/neutral position switch (on transmission)
• Red
• Right rear combination light

Exterior Lamps Wiring Diagram for Mitsubishi Pickup Mighty Max 1996

List of elements for Exterior Lamps Wiring Diagram for Mitsubishi Pickup Mighty Max 1996:

• (left i/p)
• Column switch
• Fuse 12 10a
• Fuse 2 15a
• Fuse 3 10a
• Fuse 7 15a
• Fuse block
• G106 (behind left headlight)
• G202 (left side of i/p)
• Hazard
• Hazard switch
• Head
• High level stop light (1994 model only)
• Hot at all times
• Hot in run or start
• Instrument cluster
• Left front marker light
• Left front turn light
• Left rear combination light
• License light
• Light switch
• Nca
• Off
• Park
• Right front marker light
• Right front turn light
• Right rear combination light
• Right turn ind
• Solid state
• Stop light switch (below center of i/p)
• Turn signal switch
• Turn signal/ hazard flasher unit (relay box) (below left side of dash)

GROUND DISTRIBUTION

Ground Distribution Wiring Diagram for Mitsubishi Pickup Mighty Max 1996

List of elements for Ground Distribution Wiring Diagram for Mitsubishi Pickup Mighty Max 1996:

• Battery, engine control module, data link connector, vehicle speed sensor, automatic transmission control unit, 4wd indication switch, brake fluid level switch, fuel pump, fuel gauge unit, instrument cluster, headlights, front combination lights, rear combination lights, license plate lights, intermittent wiper relay, washer motor, power window power relay, power window control relay, power window main switch, door lock actuators, central door lock control relay, seat belt warning timer relay, clutch pedal position switch (rwd-m/t), starter unlock relay (4wd-m/t), starter unlock switch (4wd-m/t), turn signal/hazard flasher unit, front turn signal lights, dimmer control switch, cigarette lighter illumination light, ashtray illumination light & clock
• Distributor signal generator, ignition power transistor & engine control module
• G111 (below battery)
• G111 (near battery)
• G121 (center of safety wall)
• G200 (left kick panel)
• G201 (right side of glove box)
• G202 (left side of i/p, near speedometer cable)
• Oxygen sensor shield (1995 exc. calif.) or heated oxygen sensor shields (1995 calif. & 1996 all)
• Rear abs control unit, automatic free wheeling hub indicator control unit & pulse generator shield
• Vacuum pump

HEADLIGHTS

Headlight Wiring Diagram for Mitsubishi Pickup Mighty Max 1996

List of elements for Headlight Wiring Diagram for Mitsubishi Pickup Mighty Max 1996:

• (left side of i/p, near speedometer cable)
• Air conditioning system
• B25
• Column switch
• Dimmer switch
• Engine control module (1996 2.4l) (right side of i/p)
• Fuse block (lower left front of dash)
• G111 (below battery)
• G202
• Head
• Hi-beam indicator
• Hot at all times
• Idle-up diode (1996 only) (left side of i/p)
• Instrument cluster
• Left headlight
• Lighting switch
• Multi- purpose fuse 12 10a
• Multi- purpose fuse 14 15a
• Multi- purpose fuse 15 15a
• Off
• Park
• Pass
• Pass switch
• Red
• Right headlight

HORN

Horn Wiring Diagram for Mitsubishi Pickup Mighty Max 1996

List of elements for Horn Wiring Diagram for Mitsubishi Pickup Mighty Max 1996:

• Column switch
• Fuse 4 10a
• Fuse block (left i/p)
• Horn
• Horn switch
• Hot in run and acc

INSTRUMENT CLUSTER

Instrument Cluster Wiring Diagram for Mitsubishi Pickup Mighty Max 1996

List of elements for Instrument Cluster Wiring Diagram for Mitsubishi Pickup Mighty Max 1996:

• (left i/p)
• 4wd ind
• 4wd indicator switch (on transmission)
• A10
• A11
• A12
• Abs ind
• Auto free wheeling hub (w/ 4wd)
• Auto free wheeling hub indicator control unit (right kick panel)
• Automatic transmission control unit (on transmission)
• B10
• Beam ind
• Brake fluid level switch (left rear of engine compartment)
• Brake ind
• Charge ind
• Check engine ind
• Combination meter
• Conn a (b-07)
• Conn b (b-06)
• Conn c (b-05)
• Coolant temp gauge unit (left side of engine)
• Cruise control unit (left kick panel)
• Data link connector (below left side of dash)
• Engine control module (right kick panel)
• Engine controls system (noise filter)
• Exterior lights system (turn signal switch)
• Fuel gauge
• Fuel gauge unit
• Fuse 7 15a
• Fuse block
• G202 (left side of dash)
• Generator
• Headlights system
• Hot in run
• Illumination (5 used)
• Ind
• Interior lights system (dimmer control switch)
• Interior lights system (light switch)
• Left turn ind
• Maintenance required
• Nca
• Oil gauge (w/ tach cluster only)
• Oil ind (w/o tach)
• Oil pressure switch (front of engine)
• Or start
• Parking brake switch (below center of dash)
• Rear anti-lock brake system control unit (below center of dash)
• Red
• Right turn ind
• Seat belt ind
• Speed sensor (reed switch)
• Tachometer
• Temperature gauge
• Voltage limiter
• Voltmeter (w/ tach cluster only)
• Warning systems (key remind switch)
• Warning systems (seat belt warning timer relay)

INTERIOR LIGHTS

Interior Light Wiring Diagram for Mitsubishi Pickup Mighty Max 1996

List of elements for Interior Light Wiring Diagram for Mitsubishi Pickup Mighty Max 1996:

• (left i/p)
• Ashtray illumination light
• Blower switch illumination light
• Cigarette lighter illumination light
• Column switch
• Dimmer control switch (left side of i/p)
• Dome light (extended cab)
• Dome light (standard and long body)
• Exterior lights system (rear combination light)
• Fuse 1 10a
• Fuse 12 10a
• Fuse block
• G202 (left side of i/p)
• Hazard switch illumination light
• Head
• Hot at all times
• Instrument cluster
• Left door switch
• Light switch
• Nca
• Off
• Park
• Radio illumination light
• Right door switch

POWER DISTRIBUTION

Power Distribution Wiring Diagram for Mitsubishi Pickup Mighty Max 1996

List of elements for Power Distribution Wiring Diagram for Mitsubishi Pickup Mighty Max 1996:

• 10a
• A/c clutch inline fuse (left side of engine compt.)
• Acc
• Air conditioning compressor clutch relay
• Air conditioning controller
• Automatic free wheeling hub indicator control unit (4wd), cruise control unit, backup light switch (m/t), automatic transmission control unit (a/t), overdrive solenoid valve (a/t), & park/neutral position switch (a/t)
• Battery
• Central door lock control relay
• Cigarette lighter
• Clock
• Column switch
• Dimmer switch
• Engine control module, cruise control module & starter relay
• Exterior lights system
• Fuse block (lower left front of dash)
• G202 (left side of i/p, near speedometer cable)
• Generator
• Hazard switch
• Head
• Headlights (high beam), instrument cluster & engine control module (1996)
• Headlights (low beam) & engine control module (1996)
• Horn
• Ignition switch
• Ignition switch (diagram 1 of 1)
• Instrument cluster, hazard switch, seat belt warning timer relay, starter unlock switch (4wd-m/t), starter unlock relay (4wd-m/t), cruise control switch (column switch), vacuum pump relay & clutch pedal position switch (m/t)
• Lighting switch
• Lock
• Main fusible link
• Main fusible link 20a
• Main fusible link 60a
• Main fusible link 80a
• Multi- purpose fuse 1 10a
• Multi- purpose fuse 12 10a
• Multi- purpose fuse 14 15a
• Multi- purpose fuse 15 15a
• Multi- purpose fuse 18 15a
• Multi- purpose fuse 2 15a
• Multi- purpose fuse 20 15a
• Multi- purpose fuse 3 10a
• Multi- purpose fuse 4 10a
• Multi- purpose fuse 5 15a
• Multi- purpose fuse 6 15a
• Multi- purpose fuse 7 15a
• Multi- purpose fuse 8 15a
• Multi- purpose fuse 9 20a
• Multiport fuel injection relay
• Multiport fuel injection relay, ignition coil & distributor signal generator
• Nca
• Off
• Overdrive off switch (a/t)
• Park
• Pass (hi)
• Pass switch
• Power window power relay
• Power window power relay & blower motor switch
• Radio
• Rear anti-lock braking system control unit
• Rear anti-lock braking system control unit, central door lock control relay, engine control module, data link connector, key remind switch, dome light, radio & clock
• Red
• Start
• Starter
• Starter relay
• Stop light switch & cruise control unit
• Sub-fusible link (on left rear of front inner fender panel)
• W/ a/t
• Wiper switch (column switch) & wiper motor

POWER DOOR LOCKS

Power Door Lock Wiring Diagram for Mitsubishi Pickup Mighty Max 1996

List of elements for Power Door Lock Wiring Diagram for Mitsubishi Pickup Mighty Max 1996:

• Central door lock control relay (in right door)
• Fuse 1 10a
• Fuse 18 15a
• Fuse block (behind left side of dash)
• G111 (below battery)
• G202 (left side of dash)
• Hot at all times
• Left door lock actuator
• Right door lock actuator

POWER WINDOWS

Power Window Wiring Diagram for Mitsubishi Pickup Mighty Max 1996

List of elements for Power Window Wiring Diagram for Mitsubishi Pickup Mighty Max 1996:

• (left rear corner of engine compt)
• Down
• Fuse 9 20a
• Fuse block (behind left side of dash)
• G106 (behind left headlight)
• G202 (left side of dash)
• Hot at all times
• Hot in run
• Left power window motor
• Left switch
• Lock switch
• Nca
• Power window control relay
• Power window main switch
• Power window power relay (relay box) (below left side of dash)
• Power window sub switch
• Red
• Right power window motor
• Right switch
• Solid state
• Sub fusible link

RADIO

Radio Wiring Diagrams, 2 Speaker System for Mitsubishi Pickup Mighty Max 1996

List of elements for Radio Wiring Diagrams, 2 Speaker System for Mitsubishi Pickup Mighty Max 1996:

• (1987-88)
• (1989-96)
• 1987-90
• 1991-96
• B-10
• B-11
• C-10
• C-11
• Fuse 1 10a
• Fuse 5 15a
• Fuse block
• Hot at all times
• Hot in acc or run
• Left speaker
• Nca
• Radio
• Right speaker

Radio Wiring Diagrams, 4 Speaker System for Mitsubishi Pickup Mighty Max 1996

List of elements for Radio Wiring Diagrams, 4 Speaker System for Mitsubishi Pickup Mighty Max 1996:

• (1987-88)
• (1987-90)
• (1989-90)
• (1991-96)
• 1987-90
• 1991-96
• B-10
• B-11
• C-10
• C-11
• Din cable
• Fuse 1 10a
• Fuse 5 15a
• Fuse block
• Hot at all times
• Hot in acc or run
• Left front speaker
• Left rear speaker
• Nca
• Radio
• Right front speaker
• Right rear speaker
• Tape player (1987-88)

STARTING/CHARGING

Charging Wiring Diagram for Mitsubishi Pickup Mighty Max 1996

List of elements for Charging Wiring Diagram for Mitsubishi Pickup Mighty Max 1996:

• Alternator
• Battery
• Charge ind
• Diode relay (left front corner of engine compartment)
• Engine controls system (ignition coil)
• Fuse 7 15a
• Fuse block
• G106 (behind left headlight)
• Hot in start and run
• Instrument cluster
• Main fusible link 20a
• Main fusible link 80a
• Starting system (starter)

Starting Wiring Diagram, Except M/T with4-Wheel Drive for Mitsubishi Pickup Mighty Max 1996

List of elements for Starting Wiring Diagram, Except M/T with4-Wheel Drive for Mitsubishi Pickup Mighty Max 1996:

• 2wd m/t
• A/t
• A/t only
• Acc
• Battery
• Clutch pedal position switch (above clutch pedal)
• Engine control module (ecm) (behind left side of dash)
• G106 (behind left headlight)
• G202 (left side of i/p)
• Ignition switch
• Lock
• Main fusible link 60a
• P/n
• Park/neutral position switch (behind left side of i/p)
• Run
• Start
• Starter
• Starter relay (left side of i/p)
• Sub fusible link (left rear of engine compartment)

Starting Wiring Diagram, M/T with 4-Wheel Drive for Mitsubishi Pickup Mighty Max 1996

List of elements for Starting Wiring Diagram, M/T with 4-Wheel Drive for Mitsubishi Pickup Mighty Max 1996:

• Acc
• Battery
• Clutch pedal position switch (above clutch pedal)
• Fuse 15a
• Fuse block
• G106 (behind left headlight)
• G202 (left side of i/p)
• Hot in start and run
• Ignition switch
• Illum
• Ind
• Interior lights (light switch)
• Lock
• Main fusible link 60a
• Run
• Start
• Starter
• Starter relay (left side of i/p
• Starter unlock relay (left kick panel)
• Starter unlock switch (behind right side of i/p)
• Sub fusible link (left rear of engine compartment)
• Warning system (seat belt warning timer)

WARNING SYSTEMS

Warning System Wiring Diagrams for Mitsubishi Pickup Mighty Max 1996

List of elements for Warning System Wiring Diagrams for Mitsubishi Pickup Mighty Max 1996:

• (lower left front of dash)
• Buzzer
• Fuse block
• G202 (left side of i/p)
• Hot at all times
• Hot in run or start
• Instrument cluster
• Key remind switch
• Left door switch
• Multi- purpose fuse 1 10a
• Multi- purpose fuse 7 15a
• Seat belt indicator
• Seat belt switch (under left seat)
• Seat belt warning timer relay (relay box) (below left side of dash)
• Solid state

WIPER/WASHER

Wiper/Washer Wiring Diagram for Mitsubishi Pickup Mighty Max 1996

List of elements for Wiper/Washer Wiring Diagram for Mitsubishi Pickup Mighty Max 1996:

• (behind left headlight) g106
• Column switch
• Fuse 6 15a
• Fuse block (left i/p)
• G202 (left side of i/p)
• Hot in run and acc
• Int
• Intermittent wiper relay
• Off
• W/ int wiper/washer only
• Washer motor (right front corner of engine compartment)
• Washer switch
• Wiper motor (rear left side of engine compartment)
• Wiper switch