Fiat DOBLO 1.9 DIESEL Da 10/2000 – DIESEL ENGINES ELECTRONIC MANAGEMENT – – WIRING DIAGRAM, LOCATION COMPONENTS, OPERATIONAL DESCRIPTION – WIRING DIAGRAM, LOCATION COMPONENTS, OPERATIONAL DESCRIPTION

Wiring diagram - DIESEL ENGINES ELECTRONIC MANAGEMENT - Fiat DOBLO 1.9 DIESEL Da 10/2000

DIESEL ENGINES ELECTRONIC MANAGEMENT - WIRING DIAGRAM Fiat DOBLO 1.9 DIESEL Da 10/2000

Get Access az összes kapcsolási rajz autó

COMPONENTS - DIESEL ENGINES ELECTRONIC MANAGEMENT - Fiat DOBLO 1.9 DIESEL Da 10/2000

Component code	Name	Assembly reference
A40	Heater plugs	-
A40	Heater plugs
B1	Engine compartment junction unit	-
B1	Engine compartment junction unit
B1	Engine compartment junction unit
B2	Junction unit under dashboard	-
B2	Junction unit under dashboard
B37	Spark plugs (MAXI FUSE) fuse	-
B37	Spark plugs (MAXI FUSE) fuse
C1	Battery earth	-
C10	Front left earth	-
C15	Facia earth, driver''s side	-
C30	Left rear earth	-
C60	Earth on engine	-
C60	Injection ECU earth	-
D4	Front/engine coupling	-
D4	Front/engine coupling
D4	Front/engine coupling
D36	Rear right door connection	-
E50	Instrument panel	-
E50	Instrument panel
I30	Brake pedal switch	-
I31	Clutch pedal switch
I50	Inertial switch
K100	Fuel heating resistance and temperature sensor
K30	Insufficient engine oil pressure (switch) sensor	-
K30	Insufficient engine oil pressure (switch) sensor
K30	Insufficient engine oil pressure (switch) sensor
K31	Water in diesel filter sensor
K41	Air flow meter
K41	Air flow meter''
K45	Coolant temperature sender unit
K45	Engine temperature sensor for i.e.
K46	RPM sensor
K46	Rpm sensor
K47	Timing sensor	-
K47	Timing sensor
K55	Accelerator pedal potentiometer	-
K55	Accelerator pedal potentiometer
K81	Fuel temperature sensor
K82	Turbocharging sensor
K82	Turbocharging sensor
K83	Fuel pressure sensor
K84	Speedometer sensor	-
K84	Speedometer sensor
L30	EGR solenoid valve
L30	EGR solenoid
L35	Waste-gate solenoid valve
L62	Butterfly casing solenoid valve	-
M1	Body computer	-
M1	Body computer
M10	Engine management ECU
M10	Engine management control unit	-
M10	Engine management control unit
M10	Plug preheating control unit
M15	Heater plugs controlunit
M15	Plug preheating control unit
M15	Plug preheating control unit
M15	Plug preheating control unit
M19	Methane injection control unit	-
N40	Fuel pump and sender unit
N41	EPIC injection pump
N77	Fuel pressure regulator
O20	Diesel preheating resistor	1044D

Location of components - DIESEL ENGINES ELECTRONIC MANAGEMENT - Fiat DOBLO 1.9 DIESEL Da 10/2000

DIESEL ENGINES ELECTRONIC MANAGEMENT - LOCATION OF COMPONENTS Fiat DOBLO 1.9 DIESEL Da 10/2000

Get Access az összes kapcsolási rajz autó

COMPONENTS - DIESEL ENGINES ELECTRONIC MANAGEMENT - Fiat DOBLO 1.9 DIESEL Da 10/2000

Component code	Name	Assembly reference
A40	Heater plugs	-
A40	Heater plugs
B1	Engine compartment junction unit	-
B1	Engine compartment junction unit
B1	Engine compartment junction unit
B2	Junction unit under dashboard	-
B2	Junction unit under dashboard
B37	Spark plugs (MAXI FUSE) fuse	-
B37	Spark plugs (MAXI FUSE) fuse
C1	Battery earth	-
C10	Front left earth	-
C15	Facia earth, driver''s side	-
C30	Left rear earth	-
C60	Earth on engine	-
C60	Injection ECU earth	-
D4	Front/engine coupling	-
D4	Front/engine coupling
D4	Front/engine coupling
D36	Rear right door connection	-
E50	Instrument panel	-
E50	Instrument panel
I30	Brake pedal switch	-
I31	Clutch pedal switch
I50	Inertial switch
K100	Fuel heating resistance and temperature sensor
K30	Insufficient engine oil pressure (switch) sensor	-
K30	Insufficient engine oil pressure (switch) sensor
K30	Insufficient engine oil pressure (switch) sensor
K31	Water in diesel filter sensor
K41	Air flow meter
K41	Air flow meter''
K45	Coolant temperature sender unit
K45	Engine temperature sensor for i.e.
K46	RPM sensor
K46	Rpm sensor
K47	Timing sensor	-
K47	Timing sensor
K55	Accelerator pedal potentiometer	-
K55	Accelerator pedal potentiometer
K81	Fuel temperature sensor
K82	Turbocharging sensor
K82	Turbocharging sensor
K83	Fuel pressure sensor
K84	Speedometer sensor	-
K84	Speedometer sensor
L30	EGR solenoid valve
L30	EGR solenoid
L35	Waste-gate solenoid valve
L62	Butterfly casing solenoid valve	-
M1	Body computer	-
M1	Body computer
M10	Engine management ECU
M10	Engine management control unit	-
M10	Engine management control unit
M10	Plug preheating control unit
M15	Heater plugs controlunit
M15	Plug preheating control unit
M15	Plug preheating control unit
M15	Plug preheating control unit
M19	Methane injection control unit	-
N40	Fuel pump and sender unit
N41	EPIC injection pump
N77	Fuel pressure regulator
O20	Diesel preheating resistor	1044D

Description - DIESEL ENGINES ELECTRONIC MANAGEMENT - Fiat DOBLO 1.9 DIESEL Da 10/2000

An electronic management system supervises and governs all engine parameters. It optimises performance and fuel consumption by responding in real time to different service conditions.The Diesel engine is fitted with a LUCAS EPIC rotary distributor type injection system. This features the pumping/distribution principle which ensures the supply to the injectors, the fuel metering and the injection advance.The system uses signals received from numerous sensors to control actuators. It is connected to the following systems:air supply;heater plugs;exhaust gas recirculation (EGR);engine cooling.The system is also controlled by means of special relays located in the engine compartment junction unit.The supply lines for the control unit and the various system components (sensors and actuators) are protected by special fuses, also located in the above mentioned junction unit.

Functional description - DIESEL ENGINES ELECTRONIC MANAGEMENT - Fiat DOBLO 1.9 DIESEL Da 10/2000

The engine control unit M10 monitors and controls the LUCAS EPIC electronic injection system. The control unit receives a supply controlled by the ignition (15/54) at pin 81 from the line protected by fuse F21 and controlled by relay R10 . The signal which controls the coil for the relay R10 coming out of pin 11 connector F of the engine compartment junction unit B01 is earthed through a bridge between pins 3 and 4 of the electric fuel pump N40 and the inertia switch I50 . In the case of an impact it interrupts the supply for the control unit M10 .The relay R9 controls the system supply: it receives a supply from the battery at pin 1 of connector A of the engine compartment junction unit B01 ; the coil is supplied by the same line and is energized by an earth signal coming from the control unit M10 , from pin 82. This energizing makes it possible to supply pins 76 and 77 of the control unit M10 via fuse F17 of the engine compartment junction unit B01 .The engine control unit M10 receives signals from the various sensors in order to monitor all engine service conditions.The sensor K46 provides information concerning the engine speed through an alternating signal sent to pin 11 of the control unit M10 . It receives an earth signal from pin 74 of the control unit. Both signals are suitably screened (pin 80);the engine temperature sensor K45 , receives a reference earth from pin 66 of the control unit M10 and supplies a signal proportional to the temperature of the engine coolant to pin 34;the insufficient engine oil pressure sensor K30 sends an earth signal, if activated, to pin 18 of the engine control unit;Other components (actuators), controlled by the control unit M10, allow the correct operation of the engine.The butterfly valve solenoid valve L62 is supplied by the relay R9 from the line for fuse F11 of the engine compartment junction unit B01 . It receives an earth from the engine management control unit M10 (from pin 65) and, in turn, sends information concerning the air temperature via pin 4, whilst pins 29 and 48 are used for the correct operation of the throttle.The EGR solenoid L30 controls exhaust gas recirculation. It is supplied by the relay R9 , from the line protected by fuse F11 and from pin 39 of the engine control unit. The solenoid valve then exchanges certain information with the control unit via pins 35, 59 and 63.The control unit M15 , which manages the pre-heating of the heater plugs A40 , is supplied (connector B pin 1) directly by the battery via the line protected by fuse B37 and via the line (connector A pin 3) for fuse F11 of the engine compartment junction unit B01 . It receives commands from pin 52 of M10 which controls the timing and sends a feedback signal to pin 49 of the control unit. Connector B is connected to the heater plugs A40. Pins 78 and 79 of M10 , together with pins 1 and 2 of connector A of M15 , are earthed.The injection control unit M10 exchanges information with the body computer M01 concerning the correct operation of the system via the CAN line, from pins 1 and 2 of the control unit to pins 36 and 37 of connector C of the body computer. The diagnostic line from pin 33 of the control unit to pin 20 of the body computer also travels between the two systems. A fault in the injection system is highlighted by the warning light in the instrument panel E50 , the management of irregularities is therefore controlled by the body computer logic. The body computer is also responsible, always using the same lines, for lighting up the heater plugs warning light when the ignition is switched ON.The body computer M01 also receives values from the speedometer sensor K84 at pins 15 and 17 of connector C.The EPIC N41 injection pump is equipped with numerous internal sensors which send information to the engine management control unit M10. These connections should be suitably screened:cam sensor, pin 13;cam sensor resistance, pin 12;rotor sensor, pin 14;cam sensor/rotor supply, pin 15;diesel temperature signal, pin 36.The control unit is therefore capable of imposing the correct control actions for the pump N41 from pins 30, 51, 60, 67, 89 and 90.