Fiat ULYSSE 2.2 16V JTD fino a 04/03 – CODE – – MY 2005 – WIRING DIAGRAM, LOCATION COMPONENTS, OPERATIONAL DESCRIPTION – WIRING DIAGRAM, LOCATION COMPONENTS, OPERATIONAL DESCRIPTION

Ottieni l'accesso a tutti gli schemi elettrici dell'auto

CODE WIRING DIAGRAM Fiat ULYSSE 2.2 16V JTD fino a 04/03

Ottieni l'accesso a tutti gli schemi elettrici dell'auto

Components - CODE - Fiat ULYSSE 2.2 16V JTD fino a 04/03

Component code	Description	Reference to the assembly
B001	ENGINE COMPARTMENT JUNCTION UNIT
C015	DRIVER''S DASHBOARD EARTH	-
C020	PASSENGER SIDE DASHBOARD EARTH	-
D006	FRONT/REAR COUPLING	-
D020	DASHBOARD/REAR COUPLING	-
H001	Ignition switch
M001	BODY COMPUTER
M010	ENGINE MANAGEMENT CONTROL UNIT
M093	STEERING WHEEL NODE CONTROL UNIT (NVO)
P091	AERIAL FOR FIAT-CODE

CODE COMPONENT LOCATION Fiat ULYSSE 2.2 16V JTD fino a 04/03

Ottieni l'accesso a tutti gli schemi elettrici dell'auto

Component code	Description	Reference to the assembly
B001	ENGINE COMPARTMENT JUNCTION UNIT
C015	DRIVER''S DASHBOARD EARTH	-
C020	PASSENGER SIDE DASHBOARD EARTH	-
D006	FRONT/REAR COUPLING	-
D020	DASHBOARD/REAR COUPLING	-
H001	Ignition switch
M001	BODY COMPUTER
M010	ENGINE MANAGEMENT CONTROL UNIT
M093	STEERING WHEEL NODE CONTROL UNIT (NVO)
P091	AERIAL FOR FIAT-CODE

To increase protection against theft attempts, an engine immobilizer system known as the CODE is used.Each time the ignition key is turned to position S, the CODE system deactivates the engine management electronic control unit functions.Each time the key is turned to position M, the CODE system sends the engine management control unit a recognition code to deactivate the immobilizing function.The keys are equipped with an electronic Transponder device that sends a coded signal to a special control unit (incorporated in the Body Computer): if it recognizes the code sent, it allows the engine to be started.The code used in the dialogue, that takes place via an aerial coaxial to the ignition switch, varies each time the engine is started (rolling code): therefore the code cannot be reproduced even using electronic scanners.The main function of the Code control unit is to recognize the key inserted in the ignition switch: it contains the secret code used in the dialogue with the key transponder. All the codes for the enabled keys and the code used in the dialogue with the engine management control unit are contained in the unit: when the key is turned to the ON position for the first time, if the key is correctly recognized, this code is transferred to the engine management control unit which remains indelibly linked to the Code unit and therefore to the Body Computer.The dialogue between the two units takes place via the two-way serial line.The function also includes the display of the status by means of the CODE/EOBD warning light in the instrument panel, connected via the CAN, coming on.

When the key is turned to position M, the aerial P091 (pins 4, 6) supplies an encrypted code contained in the ignition key to steering wheel control unit M093 (same pins connector E).Control unit M093 (pins 1 and 3 connector A) communicates the key code to body computer M001 (pins 5 and 3 connector G respectively) via the CAN network.Once checked, this information allows body computer node M001 (pins 8 and 10 connector D) to communicate an enablement signal to engine control unit M010 (pins A3 and A4 connector A) via the CAN network.The steering wheel node control unit m093 receives a power supply (pin 5 connector A and pin 4 connector D) from the Body computer node M001 (pin 11 connector B and pin 1 connector G respectively) via two lines only the second of which is protected by fuse F04.