ENGINE PERFORMANCE – Chrysler Sebring 2007 – SYSTEM WIRING DIAGRAMS

ENGINE PERFORMANCE

2.4L

2.4L, Engine Performance Wiring Diagram (1 of 4) for Chrysler Sebring 2007

List of elements for 2.4L, Engine Performance Wiring Diagram (1 of 4) for Chrysler Sebring 2007:

• (at left rear quarter panel) g303
• (downstream: in exhaust, after catalytic converter) oxygen sensor 1/2
• (in brake fluid reservoir) brake fluid level sensor
• (on left shock tower)
• (on left shock tower) g111
• 5v sply
• A804
• Accelerator pedal position sensor (top of accelerator pedal)
• App sens ground 1
• App sens ground 2
• App signal 1
• App signal 2
• Asd/main rly ctrl
• B(+)
• B15
• B16
• B20
• Brake fluid level sig
• Brake signal 1
• Brake signal 2
• C10
• C11
• Can c bus (+)
• Can c bus (-)
• Computer data lines system
• D64
• D65
• Electronics
• Esm sig
• Esm signal
• Evap monitor system switch (under left rear of vehicle)
• Evap purge ctrl
• Evap purge rtn
• Evap/purge solenoid (left rear of engine compt)
• F202
• F342
• F962
• Fuel pump ctrl
• Fuse 10a
• Fused asd/main rly out
• Fused b(+)
• G111
• G111 (on left shock tower)
• Gen sense
• Ground
• Hot at all times
• Ign sw out (run-start)
• Ign sw out (start)
• K107
• K141
• K167
• K23
• K29
• K299
• K31
• K400
• K51
• K52
• K70
• K75
• K852
• K854
• K904
• K914
• O2 1/2 heater ctrl
• O2 1/2 rtn
• O2 1/2 signal
• Powertrain control module (left rear of engine compt)
• Red
• S/c sig 1
• S/c sig 2
• S/c signal 1
• S/c signal 2
• S/c sw gnd
• S/c sw ground
• S103 (in front of left shock tower)
• S110
• S127 (in front of left shock tower)
• Sens gnd
• Sens ground
• Speed sig
• Starter ctrl
• Starting/ charging system
• Steering control module (on steering column)
• T16
• T41
• T752
• Totally integrated power module (left side of engine compt)
• Trans ctrl out
• Transmission ctrl out
• Trs t41 signal
• V71
• V72
• V937
• Vehicle speed sensor (m/t) (left side of engine compt)
• Vehicle speed signal
• Z902
• Z931

2.4L, Engine Performance Wiring Diagram (2 of 4) for Chrysler Sebring 2007

List of elements for 2.4L, Engine Performance Wiring Diagram (2 of 4) for Chrysler Sebring 2007:

• (at left
• (inside left front fender) s126
• (top of brake pedal) stop lamp switch
• 2-4 pres sig
• 5v sply
• A/c comp ctrl
• Aircondi- tioning system
• Asd/ main relay
• B(+)
• C10
• C11
• C27
• Cmp 1/2 sig
• Ect 2 sig
• Electronics
• Eot sig
• Etc motor (+)
• Etc motor (-)
• F202
• F855
• F856
• Fuse 10a
• Fuse 15a
• Fuse 30a
• Fuse 40a
• G24
• G302
• Hot at all times
• Iat sig
• Ign sw out (run- start)
• Injector 1 ctrl
• Injector 2 ctrl
• Injector 3 ctrl
• Injector 4 ctrl
• K11
• K12
• K124
• K126
• K13
• K14
• K21
• K222
• K41
• K441
• K601
• K902
• Kick panel)
• L/r pres sig
• L53
• Line pressure sensor/variable force solenoid assembly (left side of transaxle)
• Lp vfs ctrl
• Lp vfs sig
• Mfv ctrl
• O2 1/1 return
• O2 1/1 sig
• Od pres sig
• Powertrain control module (left rear of engine compt)
• Red
• Relay block (left side of engine compt)
• S120
• S172 (in breakout to c106, above transmission)
• Sens gnd
• Stop lamp sw out
• T118
• T15
• T38
• T47
• T50
• T854
• Tans ctrl out
• Totally integrated power module (left side of engine compt)
• Trans ctrl

2.4L, Engine Performance Wiring Diagram (3 of 4) for Chrysler Sebring 2007

List of elements for 2.4L, Engine Performance Wiring Diagram (3 of 4) for Chrysler Sebring 2007:

• (at top left of engine) fuel injectors
• (in breakout to c101 & pcm c2)
• (left front of engine) camshaft position solenoid 1/1
• (left front of engine) engine coolant temperature sensor 2
• (left front of engine) oil temperature sensor
• (near breakout to ignition coil 5) s190
• (on left shock tower) g111
• (right front of engine) camshaft position solenoid 1/2
• (right rear of engine) oxygen sensor 1/1
• 5v sply
• B(+)
• Camshaft position sensor 1/1 (left rear of engine)
• Camshaft position sensor 1/2 (right rear of engine)
• Ckp sig
• Cmp 1/1 sig
• Cmp 1/2 sig
• Crankshaft position sensor (right rear of engine)
• Electronics
• Engine coolant temperature sensor 1 (rear of engine)
• Etc mtr (+)
• Etc mtr (-)
• F901
• Fuel level sig 1
• Fuel pump ctrl out
• Fuel pump module (in fuel tank)
• G111 (on left shock tower)
• G303 (at left rear quarter panel)
• Gnd
• Ground
• Hot at all times
• Ign sw out (unlock- run-start)
• Instrument cluster system
• Intake air temperature sensor (on intake manifold)
• Manifold flow valve (left rear of engine)
• Map sensor (left front of engine)
• Map sig
• Mfv ctrl
• Mfv sig
• Pnk/red
• S181
• S184 (in breakout to c101 & pcm c2)
• S191 (near throttle body)
• S192 (below throttle body)
• S199
• Sens gnd
• Throttle body (left rear of engine)
• Totally integrated power module (left side of engine compt)
• Tp sens gnd
• Tp sig 1
• Tp sig 2
• Z916

2.4L, Engine Performance Wiring Diagram (4 of 4) for Chrysler Sebring 2007

List of elements for 2.4L, Engine Performance Wiring Diagram (4 of 4) for Chrysler Sebring 2007:

• (top of engine, near ignition coil breakout 4) s196
• (top right side of engine) ignition coils
• 2-4 ctrl
• 2-4 pressure switch
• 2-4 solenoid
• Autostick down sig
• Autostick up sig
• Ckp sig
• Cmp 1/1 ctrl
• Cmp 1/1 sig
• Cmp 1/2 ctrl
• Coil 1 ctrl
• Coil 2 ctrl
• Coil 3 ctrl
• Coil 4 ctrl
• Ect 1 sig
• Engine oil pressure switch (lower left side of engine)
• Eop sig
• F901
• Gen field ctrl
• Ign sw out (unlock-run-start)
• Ignition capacitor 1 (rear of engine)
• In speed sig
• Input speed sensor (on left side of transaxle)
• K122
• K15
• K17
• K18
• K19
• K20
• K22
• K24
• K276
• K42
• K44
• K602
• K76
• K900
• K915
• K922
• K942
• K99
• Knock sensor (left side of engine)
• Ks return
• Ks sig
• L/r ctrl
• L/r pressure switch
• L/r solenoid
• Map sig
• Mfv sig
• Nca
• Nol
• O2 1/1 heater ctrl
• Od ctrl
• Od pressure switch
• Od solenoid
• Out speed sig
• Output speed sensor (on left side of transaxle case)
• P3l
• Pnk/red
• Powertrain control module (left rear of engine compt)
• Prnl
• S101 (in breakout to pcm c2)
• S171 (in breakout to pcm c4)
• S194
• Sens ground
• Shift interlock system
• Starting/charging system
• T13
• T14
• T19
• T20
• T41
• T42
• T44
• T52
• T54
• T59
• T60
• T853
• Tp sens ground
• Tp sig 1
• Tp sig 2
• Trans temp sig
• Transmission range sensor (on lower left side of transaxle)
• Transmission solenoid/ pressure switch assembly (on left side of transaxle)
• Transmission temperature sensor
• Trs t1 sig
• Trs t3 sig
• Trs t41 sig
• Trs t42 sig
• Ud ctrl
• Ud solenoid

2.7L FLEX FUEL

2.7L Flex Fuel, Engine Performance Wiring Diagram, 40/41TE (1 of 5) for Chrysler Sebring 2007

List of elements for 2.7L Flex Fuel, Engine Performance Wiring Diagram, 40/41TE (1 of 5) for Chrysler Sebring 2007:

• (3.5l: left front side of engine block) (2.7l: right side of engine block) engine oil pressure switch
• (on left shock tower) g111
• (run-start)
• (unlock- run-start)
• 5v sply
• A/c comp ctrl
• A804
• A931
• Accelerator pedal position sensor (top of accelerator pedal)
• Air conditioning system
• App sens gnd 1
• App sens gnd 2
• App sig 1
• Asd/ main relay
• Asd/main rly ctrl
• Asd/main rly out
• Autostick down sig
• Autostick up sig
• B(+)
• B15
• B16
• Brake sig 1
• Brake sig 2
• C10
• C11
• C27
• Can c bus (+)
• Can c bus (-)
• Computer data lines system
• D64
• D65
• Electronics
• Eop sig
• Evap purge ctrl
• Evap purge rtn
• Evap/purge solenoid (3.5l: left rear of engine compt)
• F202
• F342
• F856
• F901
• F962
• Fuse 10a
• Fuse 15a
• Fuse 30a
• Fuse 40a
• Fused asd/ main rly out c1
• Fused b(+)
• Gen sense
• Ground
• Hot at all times
• Ign sw out
• Ign sw out (start)
• Ign sw out (unlock- run-start)
• K141
• K167
• K23
• K234
• K235
• K236
• K243
• K299
• K399
• K400
• K51
• K52
• K70
• K904
• Mtv sig
• O2 1/2 heater ctrl
• O2 1/2 sig
• O2 2/2 heater ctrl
• O2 2/2 sig
• O2 rtn (down)
• Oxygen sensor 1/2 (downstream: in exhaust, after catalytic converter)
• Oxygen sensor 2/2 (3.5l: at right side of engine)
• Pnk/red
• Powertrain control module (left rear of engine compt)
• Red
• Relay block (left side of engine compt)
• Rly out
• S/c sig 2
• S/c sw gnd
• S103 (3.5l: in front of left shock tower)
• S106 (in breakout to manifold tuning valve solenoid)
• S110
• S114
• S123 (in front of left shock tower)
• Sens gnd
• Shift interlock system
• Short runner valve solenoid (3.5l) (top front of left cylinder bank)
• Sig 1
• Sig 2
• Srv ctrl
• Srv sig
• Starting/ charging system
• Steering control module (on steering column)
• Sw gnd
• T44
• Totally integrated power module (left side of engine compt)
• V71
• V72
• V937
• Z902

2.7L Flex Fuel, Engine Performance Wiring Diagram, 40/41TE (2 of 5) for Chrysler Sebring 2007

List of elements for 2.7L Flex Fuel, Engine Performance Wiring Diagram, 40/41TE (2 of 5) for Chrysler Sebring 2007:

• (3.5l: in brake fluid reservoir) brake fluid level sensor
• (at left
• (at left rear quarter panel) g303
• (inside left front fender) s126
• (on left shock tower) g111
• (right side of front bumper beam) ambient air temperature sensor
• (top of brake pedal) stop lamp switch
• Aat rtn
• Aat sig
• App sig 2
• B(+)
• B20
• Brake fluid level sig
• C10
• C11
• Electronics
• Esm sig
• Evap monitor system switch (under left rear of vehicle)
• F202
• Fuel level sig 1
• Fuel pump ctrl
• Fuel pump ctrl out
• Fuel pump module (in fuel tank)
• Fuse 10a
• G302
• G303 (at left rear quarter panel)
• G31
• G931
• Ground
• Hot at all times
• Ign sw out (run- start)
• Instrument cluster system
• K107
• K29
• K31
• Kick panel)
• L53
• Nol
• P3l
• Powertrain control module (left rear of engine compt)
• Prnl
• Red
• S/c sig 1
• S120
• Starter ctrl
• Stop lamp sw out
• T15
• T16
• T752
• Totally integrated power module (left side of engine compt)
• Trans ctrl
• Trans ctrl out
• Transmission range sensor (2.7l: on lower left side of transaxle)
• Transmission temperature sensor
• V71
• Z916

2.7L Flex Fuel, Engine Performance Wiring Diagram, 40/41TE (3 of 5) for Chrysler Sebring 2007

List of elements for 2.7L Flex Fuel, Engine Performance Wiring Diagram, 40/41TE (3 of 5) for Chrysler Sebring 2007:

• (in breakout to c106, above transmission) s172
• (on left shock tower) g111
• 2-4 ctrl
• 2-4 pressure sig
• 2-4 pressure switch
• 2-4 solenoid
• 5v sply
• Ground
• Input speed sig
• L/r ctrl
• L/r pressure sig
• L/r pressure switch
• L/r solenoid
• Line pressure sensor/variable force solenoid assembly (2.7l: left side of transaxle)
• Lp vfs ctrl
• Lp vfs sig
• Od ctrl
• Od pressure sig
• Od pressure switch
• Od solenoid
• Out speed sig
• Powertrain control module (left rear of engine compt)
• S171 (in breakout to pcm c4)
• Sens gnd
• Sens ground
• T118
• T13
• T14
• T15
• T16
• T19
• T20
• T38
• T41
• T42
• T47
• T50
• T52
• T54
• T59
• T60
• Tans ctrl out
• Trans ctrl
• Trans ctrl out
• Trans temp sig
• Transmission solenoid/ pressure switch assembly (2.7l: on left side of transaxle)
• Trs t1 sig
• Trs t3 sig
• Trs t41 sig
• Trs t42 sig
• Ud ctrl
• Ud solenoid
• Z902

2.7L Flex Fuel, Engine Performance Wiring Diagram, 40/41TE (4 of 5) for Chrysler Sebring 2007

List of elements for 2.7L Flex Fuel, Engine Performance Wiring Diagram, 40/41TE (4 of 5) for Chrysler Sebring 2007:

• (2.7l: on left side of transaxle case) (3.5l: rear of transaxle case) output speed sensor
• (2.7l: on left side of transaxle) (3.5l: top of transaxle) input speed sensor
• (near throttle body) s191
• 2.7l
• 3.5l
• 5v sply
• Camshaft position sensor (front of left cylinder bank)
• Camshaft position sensor 1 (3.5l: top front of left cylinder bank)
• Egr valve assembly (2.7l: top rear of engine) (3.5l: rear of engine)
• Engine coolant temperature sensor (top front of engine)
• Engine coolant temperature sensor 1
• G111 (on left shock tower)
• Gnd
• Intake air temperature sensor (3.5l: on intake manifold)
• Manifold tuning valve solenoid (top right front of engine)
• Map sensor (top right rear of engine)
• Mtv ctrl
• Mtv sig
• S181 (in breakout to c101 & pcm c2)
• S182 (in injector harness, below throttle body)
• S199
• Sens gnd

2.7L Flex Fuel, Engine Performance Wiring Diagram, 40/41TE (5 of 5) for Chrysler Sebring 2007

List of elements for 2.7L Flex Fuel, Engine Performance Wiring Diagram, 40/41TE (5 of 5) for Chrysler Sebring 2007:

• (2.7l)
• (3.5l)
• (on left shock tower) g111
• (top of left cylinder bank) fuel injectors
• (top of left valve cover) ignition coils
• (top of right cylinder bank) fuel injectors
• (top of right valve cover) ignition coils
• 5v sply
• Ckp sig
• Cmp sig
• Coil 1 ctrl
• Coil 2 ctrl
• Coil 3 ctrl
• Coil 4 ctrl
• Coil 5 ctrl
• Coil 6 ctrl
• Crankshaft position sensor (2.7l) (right rear of engine)
• Ect 1 sig
• Ect sig
• Egr ctrl
• Egr sig
• Etc motor (+)
• Etc motor (-)
• Etc mtr (+)
• Etc mtr (-)
• F855
• Gen field ctrl
• Iat sig
• Ignition capacitor 1 (2.7l: rear of right cylinder bank) (3.5l: top rear of engine)
• Ignition capacitor 2 (2.7l) (rear of left cylinder bank)
• Inj 1 ctrl
• Inj 2 ctrl
• Inj 3 ctrl
• Inj 4 ctrl
• Inj 5 ctrl
• Inj 6 ctrl
• K10
• K11
• K12
• K122
• K124
• K126
• K13
• K136
• K14
• K15
• K16
• K17
• K18
• K19
• K199
• K20
• K21
• K22
• K24
• K34
• K35
• K38
• K41
• K42
• K43
• K44
• K58
• K900
• K902
• K922
• K942
• K99
• Knock sensor (below throttle body)
• Ks rtn
• Ks sig
• Map sig
• Mtv ctrl
• Nca
• O2 1/1 heater ctrl
• O2 1/1 sig
• O2 2/1 heater ctrl
• O2 2/1 sig
• O2 rtn (up)
• Oxygen sensor 1/1 (right front of engine)
• Oxygen sensor 2/1 (2.7l: left rear of engine) (3.5l: left side of engine)
• Powertrain control module (left rear of engine compt)
• S183 (2.7l: end of front left cylinder head)
• S190 (near breakout to ignition coil 5)
• S192 (below throttle body)
• S195 (between ignition coil breakouts to 4 & 6)
• Sens ground
• Starting/ charging system
• Throttle body (top rear of engine)
• Tp sens gnd
• Tp sens ground
• Tp sig 1
• Tp sig 2

2.7L Flex Fuel, Engine Performance Wiring Diagram, 62TE (1 of 5) for Chrysler Sebring 2007

List of elements for 2.7L Flex Fuel, Engine Performance Wiring Diagram, 62TE (1 of 5) for Chrysler Sebring 2007:

• (3.5l: left front side of engine block) (2.7l: right side of engine block) engine oil pressure switch
• (on left shock tower) g111
• (run-start)
• (unlock- run-start)
• 5v sply
• A/c comp ctrl
• A804
• A931
• Accelerator pedal position sensor (top of accelerator pedal)
• Air conditioning system
• App sens gnd 1
• App sens gnd 2
• App sig 1
• Asd/ main relay
• Asd/main rly ctrl
• Asd/main rly out
• Autostick down sig
• Autostick up sig
• B(+)
• B15
• B16
• Brake sig 1
• Brake sig 2
• C10
• C11
• C27
• Can c bus (+)
• Can c bus (-)
• Computer data lines system
• D64
• D65
• Electronics
• Eop sig
• Evap purge ctrl
• Evap purge rtn
• Evap/purge solenoid (3.5l: left rear of engine compt)
• F202
• F342
• F856
• F901
• F962
• Fuse 10a
• Fuse 15a
• Fuse 30a
• Fuse 40a
• Fused asd/ main rly out c1
• Fused b(+)
• Gen sense
• Ground
• Hot at all times
• Ign sw out
• Ign sw out (start)
• Ign sw out (unlock- run-start)
• K141
• K167
• K23
• K234
• K235
• K236
• K243
• K299
• K399
• K400
• K51
• K52
• K70
• K904
• Mtv sig
• O2 1/2 heater ctrl
• O2 1/2 sig
• O2 2/2 heater ctrl
• O2 2/2 sig
• O2 rtn (down)
• Oxygen sensor 1/2 (downstream: in exhaust, after catalytic converter)
• Oxygen sensor 2/2 (3.5l: at right side of engine)
• Pnk/red
• Powertrain control module (left rear of engine compt)
• Red
• Relay block (left side of engine compt)
• Rly out
• S/c sig 2
• S/c sw gnd
• S103 (3.5l: in front of left shock tower)
• S106 (in breakout to manifold tuning valve solenoid)
• S110
• S114
• S123 (in front of left shock tower)
• Sens gnd
• Shift interlock system
• Short runner valve solenoid (3.5l) (top front of left cylinder bank)
• Sig 1
• Sig 2
• Srv ctrl
• Srv sig
• Starting/ charging system
• Steering control module (on steering column)
• Sw gnd
• T44
• Totally integrated power module (left side of engine compt)
• V71
• V72
• V937
• Z902

2.7L Flex Fuel, Engine Performance Wiring Diagram, 62TE (2 of 5) for Chrysler Sebring 2007

List of elements for 2.7L Flex Fuel, Engine Performance Wiring Diagram, 62TE (2 of 5) for Chrysler Sebring 2007:

• (3.5l: in brake fluid reservoir) brake fluid level sensor
• (at left
• (at left rear quarter panel) g303
• (inside left front fender) s126
• (right side of front bumper beam) ambient air temperature sensor
• (top of brake pedal) stop lamp switch
• Aat rtn
• Aat sig
• App sig 2
• B(+)
• B20
• Brake fluid level sig
• C10
• C11
• Electronics
• Esm sig
• Evap monitor system switch (under left rear of vehicle)
• F202
• Fuel level sig 1
• Fuel pump ctrl
• Fuel pump ctrl out
• Fuel pump module (in fuel tank)
• Fuse 10a
• G111 (on left shock tower)
• G302
• G303 (at left rear quarter panel)
• G31
• G931
• Ground
• Hot at all times
• Ign sw out (run- start)
• Instrument cluster system
• K107
• K29
• K31
• Kick panel)
• L53
• Powertrain control module (left rear of engine compt)
• Red
• S/c sig 1
• S120
• Starter ctrl
• Stop lamp sw out
• T15
• T16
• T752
• Totally integrated power module (left side of engine compt)
• Trans ctrl
• Trans ctrl out
• V71
• Z916

2.7L Flex Fuel, Engine Performance Wiring Diagram, 62TE (3 of 5) for Chrysler Sebring 2007

List of elements for 2.7L Flex Fuel, Engine Performance Wiring Diagram, 62TE (3 of 5) for Chrysler Sebring 2007:

• (on left shock tower) g111
• 2-4 lr ctrl
• 2-4 press sw
• 2-4 pressure sig
• 4c sol
• 5v sply
• Dc ctrl
• Dc press sw
• Dc pressure sig
• Dc sol
• Emcc sol
• Emcc vfs ctrl
• Ground
• Input speed sig
• L/r ctrl
• L/r press sw
• L/r pressure sig
• Lc ctrl
• Lc press sw
• Lc pressure sig
• Lc sol
• Lp vfs ctrl
• Lr sol
• Od ctrl
• Od press sw
• Od pressure sig
• Od sol
• Out speed sig
• Powertrain control module (left rear of engine compt)
• S172 (in breakout to c106, above transmission)
• Sens gnd
• Sens ground
• T118
• T13
• T14
• T15
• T16
• T19
• T20
• T38
• T41
• T42
• T47
• T50
• T52
• T54
• T59
• T60
• T80
• T81
• T82
• T83
• T84
• T85
• Trans ctrl
• Trans ctrl out
• Trans temp sig
• Transfer spd sig
• Transmission solenoid/trs assembly (left side of transaxle)
• Transmission temperature sensor
• Trs t1 sig
• Trs t3 sig
• Trs t41 sig
• Trs t42 sig
• Ud ctrl
• Ud sol
• Vfs sol
• Z902

2.7L Flex Fuel, Engine Performance Wiring Diagram, 62TE (4 of 5) for Chrysler Sebring 2007

List of elements for 2.7L Flex Fuel, Engine Performance Wiring Diagram, 62TE (4 of 5) for Chrysler Sebring 2007:

• (2.7l: on left side of transaxle case) (3.5l: rear of transaxle case) output speed sensor
• (2.7l: on left side of transaxle) (3.5l: top of transaxle) input speed sensor
• (near throttle body) s191
• (rear of transaxle) transfer speed sensor
• 2.7l
• 3.5l
• 5v sply
• Camshaft position sensor (front of left cylinder bank)
• Camshaft position sensor 1 (3.5l: top front of left cylinder bank)
• Egr valve assembly (2.7l: top rear of engine) (3.5l: rear of engine)
• Engine coolant temperature sensor (top front of engine)
• Engine coolant temperature sensor 1
• G111 (on left shock tower)
• Gnd
• Intake air temperature sensor (3.5l: on intake manifold)
• Manifold tuning valve solenoid (top right front of engine)
• Map sensor (top right rear of engine)
• Mtv ctrl
• Mtv sig
• S171 (in breakout to pcm c4)
• S181 (in breakout to c101 & pcm c2)
• S182 (in injector harness, below throttle body)
• S199
• Sens gnd

2.7L Flex Fuel, Engine Performance Wiring Diagram, 62TE (5 of 5) for Chrysler Sebring 2007

List of elements for 2.7L Flex Fuel, Engine Performance Wiring Diagram, 62TE (5 of 5) for Chrysler Sebring 2007:

• (2.7l)
• (3.5l)
• (on left shock tower) g111
• (top of left cylinder bank) fuel injectors
• (top of left valve cover) ignition coils
• (top of right cylinder bank) fuel injectors
• (top of right valve cover) ignition coils
• 5v sply
• Ckp sig
• Cmp sig
• Coil 1 ctrl
• Coil 2 ctrl
• Coil 3 ctrl
• Coil 4 ctrl
• Coil 5 ctrl
• Coil 6 ctrl
• Crankshaft position sensor (2.7l) (right rear of engine)
• Ect 1 sig
• Ect sig
• Egr ctrl
• Egr sig
• Etc motor (+)
• Etc motor (-)
• Etc mtr (+)
• Etc mtr (-)
• F855
• Gen field ctrl
• Iat sig
• Ignition capacitor 1 (2.7l: rear of right cylinder bank) (3.5l: top rear of engine)
• Ignition capacitor 2 (2.7l) (rear of left cylinder bank)
• Inj 1 ctrl
• Inj 2 ctrl
• Inj 3 ctrl
• Inj 4 ctrl
• Inj 5 ctrl
• Inj 6 ctrl
• K10
• K11
• K12
• K122
• K124
• K126
• K13
• K136
• K14
• K15
• K16
• K17
• K18
• K19
• K199
• K20
• K21
• K22
• K24
• K34
• K35
• K38
• K41
• K42
• K43
• K44
• K58
• K900
• K902
• K922
• K942
• K99
• Knock sensor (below throttle body)
• Ks rtn
• Ks sig
• Map sig
• Mtv ctrl
• Nca
• O2 1/1 heater ctrl
• O2 1/1 sig
• O2 2/1 heater ctrl
• O2 2/1 sig
• O2 rtn (up)
• Oxygen sensor 1/1 (right front of engine)
• Oxygen sensor 2/1 (2.7l: left rear of engine) (3.5l: left side of engine)
• Powertrain control module (left rear of engine compt)
• S183 (2.7l: end of front left cylinder head)
• S190 (near breakout to ignition coil 5)
• S192 (below throttle body)
• S195 (between ignition coil breakouts to 4 & 6)
• Sens ground
• Starting/ charging system
• Throttle body (top rear of engine)
• Tp sens gnd
• Tp sens ground
• Tp sig 1
• Tp sig 2

3.5L

3.5L, Engine Performance Wiring Diagram, 40/41TE (1 of 5) for Chrysler Sebring 2007

List of elements for 3.5L, Engine Performance Wiring Diagram, 40/41TE (1 of 5) for Chrysler Sebring 2007:

• (3.5l: left front side of engine block) (2.7l: right side of engine block) engine oil pressure switch
• (on left shock tower) g111
• (run-start)
• (unlock- run-start)
• 5v sply
• A/c comp ctrl
• A804
• A931
• Accelerator pedal position sensor (top of accelerator pedal)
• Air conditioning system
• App sens gnd 1
• App sens gnd 2
• App sig 1
• Asd/ main relay
• Asd/main rly ctrl
• Asd/main rly out
• Autostick down sig
• Autostick up sig
• B(+)
• B15
• B16
• Brake sig 1
• Brake sig 2
• C10
• C11
• C27
• Can c bus (+)
• Can c bus (-)
• Computer data lines system
• D64
• D65
• Electronics
• Eop sig
• Evap purge ctrl
• Evap purge rtn
• Evap/purge solenoid (3.5l: left rear of engine compt)
• F202
• F342
• F856
• F901
• F962
• Fuse 10a
• Fuse 15a
• Fuse 30a
• Fuse 40a
• Fused asd/ main rly out c1
• Fused b(+)
• Gen sense
• Ground
• Hot at all times
• Ign sw out
• Ign sw out (start)
• Ign sw out (unlock- run-start)
• K141
• K167
• K23
• K234
• K235
• K236
• K243
• K299
• K399
• K400
• K51
• K52
• K70
• K904
• Mtv sig
• O2 1/2 heater ctrl
• O2 1/2 sig
• O2 2/2 heater ctrl
• O2 2/2 sig
• O2 rtn (down)
• Oxygen sensor 1/2 (downstream: in exhaust, after catalytic converter)
• Oxygen sensor 2/2 (3.5l: at right side of engine)
• Pnk/red
• Powertrain control module (left rear of engine compt)
• Red
• Relay block (left side of engine compt)
• Rly out
• S/c sig 2
• S/c sw gnd
• S103 (3.5l: in front of left shock tower)
• S106 (in breakout to manifold tuning valve solenoid)
• S110
• S114
• S123 (in front of left shock tower)
• Sens gnd
• Shift interlock system
• Short runner valve solenoid (3.5l) (top front of left cylinder bank)
• Sig 1
• Sig 2
• Srv ctrl
• Srv sig
• Starting/ charging system
• Steering control module (on steering column)
• Sw gnd
• T44
• Totally integrated power module (left side of engine compt)
• V71
• V72
• V937
• Z902

3.5L, Engine Performance Wiring Diagram, 40/41TE (2 of 5) for Chrysler Sebring 2007

List of elements for 3.5L, Engine Performance Wiring Diagram, 40/41TE (2 of 5) for Chrysler Sebring 2007:

• (3.5l: in brake fluid reservoir) brake fluid level sensor
• (at left
• (at left rear quarter panel) g303
• (inside left front fender) s126
• (on left shock tower) g111
• (right side of front bumper beam) ambient air temperature sensor
• (top of brake pedal) stop lamp switch
• Aat rtn
• Aat sig
• App sig 2
• B(+)
• B20
• Brake fluid level sig
• C10
• C11
• Electronics
• Esm sig
• Evap monitor system switch (under left rear of vehicle)
• F202
• Fuel level sig 1
• Fuel pump ctrl
• Fuel pump ctrl out
• Fuel pump module (in fuel tank)
• Fuse 10a
• G302
• G303 (at left rear quarter panel)
• G31
• G931
• Ground
• Hot at all times
• Ign sw out (run- start)
• Instrument cluster system
• K107
• K29
• K31
• Kick panel)
• L53
• Nol
• P3l
• Powertrain control module (left rear of engine compt)
• Prnl
• Red
• S/c sig 1
• S120
• Starter ctrl
• Stop lamp sw out
• T15
• T16
• T752
• Totally integrated power module (left side of engine compt)
• Trans ctrl
• Trans ctrl out
• Transmission range sensor (2.7l: on lower left side of transaxle)
• Transmission temperature sensor
• V71
• Z916

3.5L, Engine Performance Wiring Diagram, 40/41TE (3 of 5) for Chrysler Sebring 2007

List of elements for 3.5L, Engine Performance Wiring Diagram, 40/41TE (3 of 5) for Chrysler Sebring 2007:

• (in breakout to c106, above transmission) s172
• (on left shock tower) g111
• 2-4 ctrl
• 2-4 pressure sig
• 2-4 pressure switch
• 2-4 solenoid
• 5v sply
• Ground
• Input speed sig
• L/r ctrl
• L/r pressure sig
• L/r pressure switch
• L/r solenoid
• Line pressure sensor/variable force solenoid assembly (2.7l: left side of transaxle)
• Lp vfs ctrl
• Lp vfs sig
• Od ctrl
• Od pressure sig
• Od pressure switch
• Od solenoid
• Out speed sig
• Powertrain control module (left rear of engine compt)
• S171 (in breakout to pcm c4)
• Sens gnd
• Sens ground
• T118
• T13
• T14
• T15
• T16
• T19
• T20
• T38
• T41
• T42
• T47
• T50
• T52
• T54
• T59
• T60
• Tans ctrl out
• Trans ctrl
• Trans ctrl out
• Trans temp sig
• Transmission solenoid/ pressure switch assembly (2.7l: on left side of transaxle)
• Trs t1 sig
• Trs t3 sig
• Trs t41 sig
• Trs t42 sig
• Ud ctrl
• Ud solenoid
• Z902

3.5L, Engine Performance Wiring Diagram, 40/41TE (4 of 5) for Chrysler Sebring 2007

List of elements for 3.5L, Engine Performance Wiring Diagram, 40/41TE (4 of 5) for Chrysler Sebring 2007:

• (2.7l: on left side of transaxle case) (3.5l: rear of transaxle case) output speed sensor
• (2.7l: on left side of transaxle) (3.5l: top of transaxle) input speed sensor
• (near throttle body) s191
• 2.7l
• 3.5l
• 5v sply
• Camshaft position sensor (front of left cylinder bank)
• Camshaft position sensor 1 (3.5l: top front of left cylinder bank)
• Egr valve assembly (2.7l: top rear of engine) (3.5l: rear of engine)
• Engine coolant temperature sensor (top front of engine)
• Engine coolant temperature sensor 1
• G111 (on left shock tower)
• Gnd
• Intake air temperature sensor (3.5l: on intake manifold)
• Manifold tuning valve solenoid (top right front of engine)
• Map sensor (top right rear of engine)
• Mtv ctrl
• Mtv sig
• S181 (in breakout to c101 & pcm c2)
• S182 (in injector harness, below throttle body)
• S199
• Sens gnd

3.5L, Engine Performance Wiring Diagram, 40/41TE (5 of 5) for Chrysler Sebring 2007

List of elements for 3.5L, Engine Performance Wiring Diagram, 40/41TE (5 of 5) for Chrysler Sebring 2007:

• (2.7l)
• (3.5l)
• (on left shock tower) g111
• (top of left cylinder bank) fuel injectors
• (top of left valve cover) ignition coils
• (top of right cylinder bank) fuel injectors
• (top of right valve cover) ignition coils
• 5v sply
• Ckp sig
• Cmp sig
• Coil 1 ctrl
• Coil 2 ctrl
• Coil 3 ctrl
• Coil 4 ctrl
• Coil 5 ctrl
• Coil 6 ctrl
• Crankshaft position sensor (2.7l) (right rear of engine)
• Ect 1 sig
• Ect sig
• Egr ctrl
• Egr sig
• Etc motor (+)
• Etc motor (-)
• Etc mtr (+)
• Etc mtr (-)
• F855
• Gen field ctrl
• Iat sig
• Ignition capacitor 1 (2.7l: rear of right cylinder bank) (3.5l: top rear of engine)
• Ignition capacitor 2 (2.7l) (rear of left cylinder bank)
• Inj 1 ctrl
• Inj 2 ctrl
• Inj 3 ctrl
• Inj 4 ctrl
• Inj 5 ctrl
• Inj 6 ctrl
• K10
• K11
• K12
• K122
• K124
• K126
• K13
• K136
• K14
• K15
• K16
• K17
• K18
• K19
• K199
• K20
• K21
• K22
• K24
• K34
• K35
• K38
• K41
• K42
• K43
• K44
• K58
• K900
• K902
• K922
• K942
• K99
• Knock sensor (below throttle body)
• Ks rtn
• Ks sig
• Map sig
• Mtv ctrl
• Nca
• O2 1/1 heater ctrl
• O2 1/1 sig
• O2 2/1 heater ctrl
• O2 2/1 sig
• O2 rtn (up)
• Oxygen sensor 1/1 (right front of engine)
• Oxygen sensor 2/1 (2.7l: left rear of engine) (3.5l: left side of engine)
• Powertrain control module (left rear of engine compt)
• S183 (2.7l: end of front left cylinder head)
• S190 (near breakout to ignition coil 5)
• S192 (below throttle body)
• S195 (between ignition coil breakouts to 4 & 6)
• Sens ground
• Starting/ charging system
• Throttle body (top rear of engine)
• Tp sens gnd
• Tp sens ground
• Tp sig 1
• Tp sig 2

3.5L, Engine Performance Wiring Diagram, 62TE (1 of 5) for Chrysler Sebring 2007

List of elements for 3.5L, Engine Performance Wiring Diagram, 62TE (1 of 5) for Chrysler Sebring 2007:

• (3.5l: left front side of engine block) (2.7l: right side of engine block) engine oil pressure switch
• (on left shock tower) g111
• (run-start)
• (unlock- run-start)
• 5v sply
• A/c comp ctrl
• A804
• A931
• Accelerator pedal position sensor (top of accelerator pedal)
• Air conditioning system
• App sens gnd 1
• App sens gnd 2
• App sig 1
• Asd/ main relay
• Asd/main rly ctrl
• Asd/main rly out
• Autostick down sig
• Autostick up sig
• B(+)
• B15
• B16
• Brake sig 1
• Brake sig 2
• C10
• C11
• C27
• Can c bus (+)
• Can c bus (-)
• Computer data lines system
• D64
• D65
• Electronics
• Eop sig
• Evap purge ctrl
• Evap purge rtn
• Evap/purge solenoid (3.5l: left rear of engine compt)
• F202
• F342
• F856
• F901
• F962
• Fuse 10a
• Fuse 15a
• Fuse 30a
• Fuse 40a
• Fused asd/ main rly out c1
• Fused b(+)
• Gen sense
• Ground
• Hot at all times
• Ign sw out
• Ign sw out (start)
• Ign sw out (unlock- run-start)
• K141
• K167
• K23
• K234
• K235
• K236
• K243
• K299
• K399
• K400
• K51
• K52
• K70
• K904
• Mtv sig
• O2 1/2 heater ctrl
• O2 1/2 sig
• O2 2/2 heater ctrl
• O2 2/2 sig
• O2 rtn (down)
• Oxygen sensor 1/2 (downstream: in exhaust, after catalytic converter)
• Oxygen sensor 2/2 (3.5l: at right side of engine)
• Pnk/red
• Powertrain control module (left rear of engine compt)
• Red
• Relay block (left side of engine compt)
• Rly out
• S/c sig 2
• S/c sw gnd
• S103 (3.5l: in front of left shock tower)
• S106 (in breakout to manifold tuning valve solenoid)
• S110
• S114
• S123 (in front of left shock tower)
• Sens gnd
• Shift interlock system
• Short runner valve solenoid (3.5l) (top front of left cylinder bank)
• Sig 1
• Sig 2
• Srv ctrl
• Srv sig
• Starting/ charging system
• Steering control module (on steering column)
• Sw gnd
• T44
• Totally integrated power module (left side of engine compt)
• V71
• V72
• V937
• Z902

3.5L, Engine Performance Wiring Diagram, 62TE (2 of 5) for Chrysler Sebring 2007

List of elements for 3.5L, Engine Performance Wiring Diagram, 62TE (2 of 5) for Chrysler Sebring 2007:

• (3.5l: in brake fluid reservoir) brake fluid level sensor
• (at left
• (at left rear quarter panel) g303
• (inside left front fender) s126
• (right side of front bumper beam) ambient air temperature sensor
• (top of brake pedal) stop lamp switch
• Aat rtn
• Aat sig
• App sig 2
• B(+)
• B20
• Brake fluid level sig
• C10
• C11
• Electronics
• Esm sig
• Evap monitor system switch (under left rear of vehicle)
• F202
• Fuel level sig 1
• Fuel pump ctrl
• Fuel pump ctrl out
• Fuel pump module (in fuel tank)
• Fuse 10a
• G111 (on left shock tower)
• G302
• G303 (at left rear quarter panel)
• G31
• G931
• Ground
• Hot at all times
• Ign sw out (run- start)
• Instrument cluster system
• K107
• K29
• K31
• Kick panel)
• L53
• Powertrain control module (left rear of engine compt)
• Red
• S/c sig 1
• S120
• Starter ctrl
• Stop lamp sw out
• T15
• T16
• T752
• Totally integrated power module (left side of engine compt)
• Trans ctrl
• Trans ctrl out
• V71
• Z916

3.5L, Engine Performance Wiring Diagram, 62TE (3 of 5) for Chrysler Sebring 2007

List of elements for 3.5L, Engine Performance Wiring Diagram, 62TE (3 of 5) for Chrysler Sebring 2007:

• (on left shock tower) g111
• 2-4 lr ctrl
• 2-4 press sw
• 2-4 pressure sig
• 4c sol
• 5v sply
• Dc ctrl
• Dc press sw
• Dc pressure sig
• Dc sol
• Emcc sol
• Emcc vfs ctrl
• Ground
• Input speed sig
• L/r ctrl
• L/r press sw
• L/r pressure sig
• Lc ctrl
• Lc press sw
• Lc pressure sig
• Lc sol
• Lp vfs ctrl
• Lr sol
• Od ctrl
• Od press sw
• Od pressure sig
• Od sol
• Out speed sig
• Powertrain control module (left rear of engine compt)
• S172 (in breakout to c106, above transmission)
• Sens gnd
• Sens ground
• T118
• T13
• T14
• T15
• T16
• T19
• T20
• T38
• T41
• T42
• T47
• T50
• T52
• T54
• T59
• T60
• T80
• T81
• T82
• T83
• T84
• T85
• Trans ctrl
• Trans ctrl out
• Trans temp sig
• Transfer spd sig
• Transmission solenoid/trs assembly (left side of transaxle)
• Transmission temperature sensor
• Trs t1 sig
• Trs t3 sig
• Trs t41 sig
• Trs t42 sig
• Ud ctrl
• Ud sol
• Vfs sol
• Z902

3.5L, Engine Performance Wiring Diagram, 62TE (4 of 5) for Chrysler Sebring 2007

List of elements for 3.5L, Engine Performance Wiring Diagram, 62TE (4 of 5) for Chrysler Sebring 2007:

• (2.7l: on left side of transaxle case) (3.5l: rear of transaxle case) output speed sensor
• (2.7l: on left side of transaxle) (3.5l: top of transaxle) input speed sensor
• (near throttle body) s191
• (rear of transaxle) transfer speed sensor
• 2.7l
• 3.5l
• 5v sply
• Camshaft position sensor (front of left cylinder bank)
• Camshaft position sensor 1 (3.5l: top front of left cylinder bank)
• Egr valve assembly (2.7l: top rear of engine) (3.5l: rear of engine)
• Engine coolant temperature sensor (top front of engine)
• Engine coolant temperature sensor 1
• G111 (on left shock tower)
• Gnd
• Intake air temperature sensor (3.5l: on intake manifold)
• Manifold tuning valve solenoid (top right front of engine)
• Map sensor (top right rear of engine)
• Mtv ctrl
• Mtv sig
• S171 (in breakout to pcm c4)
• S181 (in breakout to c101 & pcm c2)
• S182 (in injector harness, below throttle body)
• S199
• Sens gnd

3.5L, Engine Performance Wiring Diagram, 62TE (5 of 5) for Chrysler Sebring 2007

List of elements for 3.5L, Engine Performance Wiring Diagram, 62TE (5 of 5) for Chrysler Sebring 2007:

• (2.7l)
• (3.5l)
• (on left shock tower) g111
• (top of left cylinder bank) fuel injectors
• (top of left valve cover) ignition coils
• (top of right cylinder bank) fuel injectors
• (top of right valve cover) ignition coils
• 5v sply
• Ckp sig
• Cmp sig
• Coil 1 ctrl
• Coil 2 ctrl
• Coil 3 ctrl
• Coil 4 ctrl
• Coil 5 ctrl
• Coil 6 ctrl
• Crankshaft position sensor (2.7l) (right rear of engine)
• Ect 1 sig
• Ect sig
• Egr ctrl
• Egr sig
• Etc motor (+)
• Etc motor (-)
• Etc mtr (+)
• Etc mtr (-)
• F855
• Gen field ctrl
• Iat sig
• Ignition capacitor 1 (2.7l: rear of right cylinder bank) (3.5l: top rear of engine)
• Ignition capacitor 2 (2.7l) (rear of left cylinder bank)
• Inj 1 ctrl
• Inj 2 ctrl
• Inj 3 ctrl
• Inj 4 ctrl
• Inj 5 ctrl
• Inj 6 ctrl
• K10
• K11
• K12
• K122
• K124
• K126
• K13
• K136
• K14
• K15
• K16
• K17
• K18
• K19
• K199
• K20
• K21
• K22
• K24
• K34
• K35
• K38
• K41
• K42
• K43
• K44
• K58
• K900
• K902
• K922
• K942
• K99
• Knock sensor (below throttle body)
• Ks rtn
• Ks sig
• Map sig
• Mtv ctrl
• Nca
• O2 1/1 heater ctrl
• O2 1/1 sig
• O2 2/1 heater ctrl
• O2 2/1 sig
• O2 rtn (up)
• Oxygen sensor 1/1 (right front of engine)
• Oxygen sensor 2/1 (2.7l: left rear of engine) (3.5l: left side of engine)
• Powertrain control module (left rear of engine compt)
• S183 (2.7l: end of front left cylinder head)
• S190 (near breakout to ignition coil 5)
• S192 (below throttle body)
• S195 (between ignition coil breakouts to 4 & 6)
• Sens ground
• Starting/ charging system
• Throttle body (top rear of engine)
• Tp sens gnd
• Tp sens ground
• Tp sig 1
• Tp sig 2