ENGINE PERFORMANCE – Porsche 911 Turbo S 2012 – SYSTEM WIRING DIAGRAMS

ENGINE PERFORMANCE

3.6L

3.6L, Engine Performance Wiring Diagram (1 of 6) for Porsche 911 Turbo S 2012

List of elements for 3.6L, Engine Performance Wiring Diagram (1 of 6) for Porsche 911 Turbo S 2012:

• (right rear of engine compt) gp9
• +5v
• +5v poten 2
• +5v vehicle sens
• 5v sply
• Brake booster
• Can high 1
• Can low 1
• Clutch sw
• Clutch sw up
• Computer data lines system
• Cooling fans system
• Data
• Diagnosis msg
• Dme control unit (left front of engine compt)
• Dme relay
• Fan ctrl 1
• Fan ctrl 2
• Fuel pump
• Fuse 10a
• Fuse 15a
• Fuse 25a
• Gp2 (left front of luggage compt)
• Heater +
• Heater -
• Ipn ground
• Lambda ctrl
• Leakage diagnosis unit
• Leakage temperature sensor diagnosis unit
• Oxygen sens gnd
• Oxygen sens sig
• Oxygen sensor
• Oxygen sensor downstream of catalytic b1
• Oxygen sensor downstream of catalytic b2
• Oxygen sensor upstream of catalytic b1
• Oxygen sensor upstream of catalytic b2
• Pedal sens
• Pedal value
• Pedal value sens
• Pedal value sensor (behind accelerator pedal)
• Pmp current
• Red
• Relay support 2 (row b) (behind left rear seat well)
• Relay term 30
• Resistor
• Sens 1 gnd
• Sens gnd
• Sens sig
• Sensors 2 gnd
• Shut-off valve
• Starter relay
• Starting/ charging system
• Sw nvld +
• Sw nvld -
• Tank leak diagn
• Term 15
• Term 30
• Term 30f
• Term 31
• Term 87
• Transm oil temp
• Value sens
• X031
• X032
• X901

3.6L, Engine Performance Wiring Diagram (2 of 6) for Porsche 911 Turbo S 2012

List of elements for 3.6L, Engine Performance Wiring Diagram (2 of 6) for Porsche 911 Turbo S 2012:

• (behind left rear seat well) relay support 2
• (rear of luggage compt) electric fuel pump control unit
• Brake vacuum sensor
• Dme relay 1
• Engine compartment temperature sensor (middle of engine)
• Front bcm
• Fuse 10a
• Fuse 15a
• Fuse 5a
• Gp12
• Hot at all times
• Main fuse box (right side of dash)
• Midi fuse 100a
• Neutral gear sensor
• Pump +
• Pump -
• Pwm
• Rear bcm
• Red
• Relay support 2 (row c) (behind left rear seat well)
• Right front fuse box (row b)
• Sig
• Sig +
• Term 15
• Term 15sv
• Term 31
• Term 87
• X031
• X032

3.6L, Engine Performance Wiring Diagram (3 of 6) for Porsche 911 Turbo S 2012

List of elements for 3.6L, Engine Performance Wiring Diagram (3 of 6) for Porsche 911 Turbo S 2012:

• (intake manifold) throttle valve adjustment unit
• (left rear of engine compt lid) engine compartment purge fan 1
• Camshaft adjuster bank 1
• Camshaft adjuster bank 2
• Can high
• Can low
• Computer data lines system
• Fuel lvl sens
• Fuse 20a
• Gnd
• Heating element thermostat map
• Hot at all times
• Instrument cluster
• Intake man pressure sensor
• Knock sensor 1 (engine block)
• Knock sensor 2 (engine block)
• Left front fuse box (row b)
• Lift valve adjuster b1
• Lift valve adjuster b2
• Lvl sens (empty)
• Lvl sens (full)
• Mtr +
• Mtr -
• Ntc
• Output
• Pump +
• Pump -
• Pwm
• Red
• S1 full
• S2 empty
• Sig
• Sig 1
• Sig 2
• Tank flange fuel pump
• Term 31
• Term 87
• X045
• X240

3.6L, Engine Performance Wiring Diagram (4 of 6) for Porsche 911 Turbo S 2012

List of elements for 3.6L, Engine Performance Wiring Diagram (4 of 6) for Porsche 911 Turbo S 2012:

• (behind left rear seat well) relay support 2
• (not used)
• (right rear of engine compt lid) engine compartment purge fan 2
• 87a
• Engine flush high relay
• Engine flush low relay
• Fuel pump relay
• Gp23
• Gp9 (right rear of engine compt)
• Intake manifold switch-over valve
• Nca
• Oil level sensor (under engine, on oil pan)
• Oil temp +
• Oil temp gnd
• Oil temperature sensor gear wheel set manual transmission 991
• Oil temperature sensor gear wheel set pdk 991
• Output
• Pwm
• Rear bcm
• Red
• Stop light sw
• Stop light sw stop light switch (brake pedal linkage)
• Temp + oil
• Temp gnd oil
• Term 15
• Term 31
• Term 87
• X031
• X240

3.6L, Engine Performance Wiring Diagram (5 of 6) for Porsche 911 Turbo S 2012

List of elements for 3.6L, Engine Performance Wiring Diagram (5 of 6) for Porsche 911 Turbo S 2012:

• (left rear & right front of engine)
• (right side of engine) oil pressure & temperature sensor
• 12 v
• 3-5v
• 5v sply
• Accumul flap
• Air cleaner
• Camshaft sens
• Camshaft sensor bank 1
• Camshaft sensor bank 2
• Coolant bypass valve
• Coolant cylinder head temperature sensor
• Coolant shut-off valve 2 gear wheel set manual transmission
• Coolant shut-off valve 2 gear wheel set pdk
• Crankshaft speed sensor
• Crash signal
• Cyl 2 ls
• Cyl 5 ls
• Dme control unit (left front of engine compt)
• Gnd
• High rail pressure sensor
• Ignition cyl 3
• Ignition cyl 4
• Ignition cyl 5
• Ntc
• Oil press valve
• Oil pressure
• Oil pressure regulating valve
• Out
• Output
• Positive
• Pulses
• Red
• Sens 3 gnd
• Sens bank1 gnd
• Sens bank2 gnd
• Sensors 2 gnd
• Shut-off vlv
• Sig
• Sound symposer
• Sound symposer valve
• Speed sender
• Temp radiator
• Term
• Term 31
• Term 87
• Thro vlv gnd
• Throttle valve
• X031

3.6L, Engine Performance Wiring Diagram (6 of 6) for Porsche 911 Turbo S 2012

List of elements for 3.6L, Engine Performance Wiring Diagram (6 of 6) for Porsche 911 Turbo S 2012:

• (fuel filler neck) tank vent valve
• (top of 1, 2, 3, 4, 5 & 6 cylinders)
• 5v eng sens
• Adjuster b2
• Air cleaner flap valve
• Bar ignition module cylinder 1
• Bar ignition module cylinder 2
• Bar ignition module cylinder 3
• Bar ignition module cylinder 4
• Bar ignition module cylinder 5
• Bar ignition module cylinder 6
• Brk pedal sw
• Camshaft
• Charge air temp
• Cyl 1 hs
• Cyl 1 ls
• Cyl 2 hs
• Cyl 3 hs
• Cyl 3 ls
• Cyl 4 hs
• Cyl 4 ls
• Cyl 5 hs
• Cyl 6 hs
• Cyl 6 ls
• Dme control unit (left front of engine compt)
• Engine compt
• Fan ctrl
• Flow control valve
• Flow ctrl vlv1
• Fuel injector cylinder 1
• Fuel injector cylinder 2
• Fuel injector cylinder 3
• Fuel injector cylinder 4
• Fuel injector cylinder 5
• Fuel injector cylinder 6
• Gp46
• Gp9 (right rear of engine compt)
• Hi press snsr
• Ignition cyl 1
• Ignition cyl 2
• Ignition cyl 6
• Intake press
• Knock sens 1
• Knock sens 2
• Neut gear sens
• Oil press sens
• Oil temp sens
• Positive
• Pwm
• Red
• Resonance flap
• Sensors 1 gnd
• Shut-off valve
• Signal
• Tank vent vlv
• Term 31
• Term 4a
• Term 87
• Thermostat map
• Throt vlv 1
• Throt vlv mtr +
• Throt vlv mtr -
• Throttle valve
• Valve for tuning flap 1
• Vlv lift adj b1
• Water temp
• X031

3.8L

3.8L, Engine Performance Wiring Diagram (1 of 6) for Porsche 911 Turbo S 2012

List of elements for 3.8L, Engine Performance Wiring Diagram (1 of 6) for Porsche 911 Turbo S 2012:

• (right rear of engine compt) gp9
• +5v
• +5v poten 2
• +5v vehicle sens
• 5v sply
• Brake booster
• Can high 1
• Can low 1
• Clutch sw
• Clutch sw up
• Computer data lines system
• Cooling fans system
• Data
• Diagnosis msg
• Dme control unit (left front of engine compt)
• Dme relay
• Fan ctrl 1
• Fan ctrl 2
• Fuel pump
• Fuse 10a
• Fuse 15a
• Fuse 25a
• Gp2 (left front of luggage compt)
• Heater +
• Heater -
• Ipn ground
• Lambda ctrl
• Leakage diagnosis unit
• Leakage temperature sensor diagnosis unit
• Oxygen sens gnd
• Oxygen sens sig
• Oxygen sensor
• Oxygen sensor downstream of catalytic b1
• Oxygen sensor downstream of catalytic b2
• Oxygen sensor upstream of catalytic b1
• Oxygen sensor upstream of catalytic b2
• Pedal sens
• Pedal value
• Pedal value sens
• Pedal value sensor (behind accelerator pedal)
• Pmp current
• Red
• Relay support 2 (row b) (behind left rear seat well)
• Relay term 30
• Resistor
• Sens 1 gnd
• Sens gnd
• Sens sig
• Sensors 2 gnd
• Shut-off valve
• Starter relay
• Starting/ charging system
• Sw nvld +
• Sw nvld -
• Tank leak diagn
• Term 15
• Term 30
• Term 30f
• Term 31
• Term 87
• Transm oil temp
• Value sens
• X031
• X032
• X901

3.8L, Engine Performance Wiring Diagram (2 of 6) for Porsche 911 Turbo S 2012

List of elements for 3.8L, Engine Performance Wiring Diagram (2 of 6) for Porsche 911 Turbo S 2012:

• (behind left rear seat well) relay support 2
• (rear of luggage compt) electric fuel pump control unit
• Brake vacuum sensor
• Dme relay 1
• Engine compartment temperature sensor (middle of engine)
• Front bcm
• Fuse 10a
• Fuse 15a
• Fuse 5a
• Gp12
• Hot at all times
• Main fuse box (right side of dash)
• Midi fuse 100a
• Neutral gear sensor
• Pump +
• Pump -
• Pwm
• Rear bcm
• Red
• Relay support 2 (row c) (behind left rear seat well)
• Right front fuse box (row b)
• Sig
• Sig +
• Term 15
• Term 15sv
• Term 31
• Term 87
• X031
• X032

3.8L, Engine Performance Wiring Diagram (3 of 6) for Porsche 911 Turbo S 2012

List of elements for 3.8L, Engine Performance Wiring Diagram (3 of 6) for Porsche 911 Turbo S 2012:

• (intake manifold) throttle valve adjustment unit
• (left rear of engine compt lid) engine compartment purge fan 1
• Camshaft adjuster bank 1
• Camshaft adjuster bank 2
• Can high
• Can low
• Computer data lines system
• Fuel lvl sens
• Fuse 20a
• Gnd
• Heating element thermostat map
• Hot at all times
• Instrument cluster
• Intake man pressure sensor
• Knock sensor 1 (engine block)
• Knock sensor 2 (engine block)
• Left front fuse box (row b)
• Lift valve adjuster b1
• Lift valve adjuster b2
• Lvl sens (empty)
• Lvl sens (full)
• Mtr +
• Mtr -
• Ntc
• Output
• Pump +
• Pump -
• Pwm
• Red
• S1 full
• S2 empty
• Sig
• Sig 1
• Sig 2
• Tank flange fuel pump
• Term 31
• Term 87
• X045
• X240

3.8L, Engine Performance Wiring Diagram (4 of 6) for Porsche 911 Turbo S 2012

List of elements for 3.8L, Engine Performance Wiring Diagram (4 of 6) for Porsche 911 Turbo S 2012:

• (behind left rear seat well) relay support 2
• (not used)
• (right rear of engine compt lid) engine compartment purge fan 2
• 87a
• Engine flush high relay
• Engine flush low relay
• Fuel pump relay
• Gp23
• Gp9 (right rear of engine compt)
• Intake manifold switch-over valve
• Nca
• Oil level sensor (under engine, on oil pan)
• Oil temp +
• Oil temp gnd
• Oil temperature sensor gear wheel set manual transmission 991
• Oil temperature sensor gear wheel set pdk 991
• Output
• Pwm
• Rear bcm
• Red
• Stop light sw
• Stop light sw stop light switch (brake pedal linkage)
• Temp + oil
• Temp gnd oil
• Term 15
• Term 31
• Term 87
• X031
• X240

3.8L, Engine Performance Wiring Diagram (5 of 6) for Porsche 911 Turbo S 2012

List of elements for 3.8L, Engine Performance Wiring Diagram (5 of 6) for Porsche 911 Turbo S 2012:

• (left rear & right front of engine)
• (right side of engine) oil pressure & temperature sensor
• 12 v
• 3-5v
• 5v sply
• Accumul flap
• Air cleaner
• Camshaft sens
• Camshaft sensor bank 1
• Camshaft sensor bank 2
• Coolant bypass valve
• Coolant cylinder head temperature sensor
• Coolant shut-off valve 2 gear wheel set manual transmission
• Coolant shut-off valve 2 gear wheel set pdk
• Crankshaft speed sensor
• Crash signal
• Cyl 2 ls
• Cyl 5 ls
• Dme control unit (left front of engine compt)
• Gnd
• High rail pressure sensor
• Ignition cyl 3
• Ignition cyl 4
• Ignition cyl 5
• Ntc
• Oil press valve
• Oil pressure
• Oil pressure regulating valve
• Out
• Output
• Positive
• Pulses
• Red
• Sens 3 gnd
• Sens bank1 gnd
• Sens bank2 gnd
• Sensors 2 gnd
• Shut-off vlv
• Sig
• Sound symposer
• Sound symposer valve
• Speed sender
• Temp radiator
• Term
• Term 31
• Term 87
• Thro vlv gnd
• Throttle valve
• X031

3.8L, Engine Performance Wiring Diagram (6 of 6) for Porsche 911 Turbo S 2012

List of elements for 3.8L, Engine Performance Wiring Diagram (6 of 6) for Porsche 911 Turbo S 2012:

• (fuel filler neck) tank vent valve
• (top of 1, 2, 3, 4, 5 & 6 cylinders)
• 5v eng sens
• Adjuster b2
• Air cleaner flap valve
• Bar ignition module cylinder 1
• Bar ignition module cylinder 2
• Bar ignition module cylinder 3
• Bar ignition module cylinder 4
• Bar ignition module cylinder 5
• Bar ignition module cylinder 6
• Brk pedal sw
• Camshaft
• Charge air temp
• Cyl 1 hs
• Cyl 1 ls
• Cyl 2 hs
• Cyl 3 hs
• Cyl 3 ls
• Cyl 4 hs
• Cyl 4 ls
• Cyl 5 hs
• Cyl 6 hs
• Cyl 6 ls
• Dme control unit (left front of engine compt)
• Engine compt
• Fan ctrl
• Flow control valve
• Flow ctrl vlv1
• Fuel injector cylinder 1
• Fuel injector cylinder 2
• Fuel injector cylinder 3
• Fuel injector cylinder 4
• Fuel injector cylinder 5
• Fuel injector cylinder 6
• Gp46
• Gp9 (right rear of engine compt)
• Hi press snsr
• Ignition cyl 1
• Ignition cyl 2
• Ignition cyl 6
• Intake press
• Knock sens 1
• Knock sens 2
• Neut gear sens
• Oil press sens
• Oil temp sens
• Positive
• Pwm
• Red
• Resonance flap
• Sensors 1 gnd
• Shut-off valve
• Signal
• Tank vent vlv
• Term 31
• Term 4a
• Term 87
• Thermostat map
• Throt vlv 1
• Throt vlv mtr +
• Throt vlv mtr -
• Throttle valve
• Valve for tuning flap 1
• Vlv lift adj b1
• Water temp
• X031

3.8L TWIN TURBO

3.8L Twin Turbo, Engine Performance Wiring Diagram (1 of 5) for Porsche 911 Turbo S 2012

List of elements for 3.8L Twin Turbo, Engine Performance Wiring Diagram (1 of 5) for Porsche 911 Turbo S 2012:

• (info not available)
• (right rear of engine compt) gp9
• Air pump
• Behind catalytic converter bank 1
• Behind catalytic converter bank 2
• Blower stage 2
• Can high 1
• Can low 1
• Clk sig h-
• Clutch sw
• Comp curent
• Computer data lines system
• Coolant pump
• Coolant sw
• Cooling fans system
• Current distri- butor (behind right side of dash)
• Dme control unit (left front of engine compt)
• Dme relay
• Dmtl-heating
• Fuel pump rly 1
• Fuel pump rly 2
• Fuel pump sig
• Fuse 60a
• Fuse f3 7.5a
• Fuse f4 20a
• Fuse f5 25a
• Fuse f6 25a
• Fuse f7 15a
• Fuse f7 80a
• Fuse f8 7.5a
• Fuse holder d
• Gnd
• Gp8
• Hot at all times
• Lsf heater nk
• Lsf heater nk b2
• Lsf sig
• Lsf signal nk b1
• Maxi fuse
• Oxy sens 1 gnd
• Oxy sens 1 sig
• Oxy sens 2 gnd
• Oxy sens 2 sig
• Oxy sens heater
• Oxygen sensor ahead of catalytic converter bank 1
• Oxygen sensor ahead of catalytic converter bank 2
• Pedal sens
• Pedal value sens
• Pmp current
• Porsche access system
• Pumping current
• Purge fan 1
• Pwg +5v 1
• Pwg +5v poti 2
• Quantity control valve
• Red
• Resistor
• Secondary air pump (engine, next to intake bride)
• Secondary air pump relay (relay support 2)
• Sens gnd
• Shut-off valve
• Starter
• Starter relay
• Starting/ charging system
• Tailgate sw
• Tank leak diagn
• Tank leakage
• Tank leakage diagnostics module
• Term 15
• Term 30
• Term 31
• Term 87
• Ubatt h+
• Vollt re+
• X021
• X023
• X591
• X593

3.8L Twin Turbo, Engine Performance Wiring Diagram (2 of 5) for Porsche 911 Turbo S 2012

List of elements for 3.8L Twin Turbo, Engine Performance Wiring Diagram (2 of 5) for Porsche 911 Turbo S 2012:

• (fuel tank, under battery) fuel pump level sensor
• (rear of luggage compt) fuel pump control unit
• (relay support 1) fuel pump relay 1
• (relay support 1) fuel pump relay 2
• Bank 1
• Bank 2
• Camshaft sensor 1 cylinder (1-3) (left rear & right front of engine)
• Camshaft sensor 2 cylinder (4-6) (left rear & right front of engine)
• Can high
• Can low
• Computer data lines system
• Cooling water shutoff valve
• Dme relay
• Electrical water pump
• Exhaust temperature sensor (coupe)
• Gp3 (left side of support frame)
• Ground
• Instrument cluster
• Knock sensor 1 cylinder (1-3) (engine block)
• Knock sensor 2 cylinder (4-6) (engine block)
• Lvl grd
• Lvl sens
• Nca
• Pedal value sensor (behind accelerator pedal)
• Pump +
• Pump -
• Pwm
• Suply
• Tank vent valve (fuel filler neck)
• Term 31
• Term 87
• Tog masse
• X021
• X023
• X592

3.8L Twin Turbo, Engine Performance Wiring Diagram (3 of 5) for Porsche 911 Turbo S 2012

List of elements for 3.8L Twin Turbo, Engine Performance Wiring Diagram (3 of 5) for Porsche 911 Turbo S 2012:

• (side of expansion tank) cooling water level switch
• (top of engine) camshaft adjustment valve 1 cylinder (1-3)
• (top of engine) camshaft adjustment valve 2 cylinder (4-6)
• Actuation
• Air bag control unit (below center console)
• Bank 1
• Bank 2
• Camshaft sens 1
• Camshaft sens 2
• Charge air pressure positioner 2
• Crash input
• Crash out
• Cylinder 2
• Cylinder 3
• Cylinder 4
• Cylinder 5
• Cylinder 5-
• Diverter valve
• Dme control unit (left front of engine compt)
• Engine sens 2
• Engine speed +
• Engine speed -
• Engine speed sensor (clutch bell housing)
• Exhaust temperature sensor (convertible)
• Fuse f1 25a
• Fuse f2 25a
• Fuse holder d
• Generator
• Gnd
• Gnd eng sens 3
• Gp8 (left rear of engine compt)
• Ground
• Hot at all times
• Lift valve control 2 cylinder (4-6)
• Lift valve control cylinders (1-3)
• Nca
• Oil pressure
• Oil pressure regulation valve
• Position
• Positioner 2
• Shield
• System starting/charging
• Throttle valve
• X021
• X591
• X592
• X593

3.8L Twin Turbo, Engine Performance Wiring Diagram (4 of 5) for Porsche 911 Turbo S 2012

List of elements for 3.8L Twin Turbo, Engine Performance Wiring Diagram (4 of 5) for Porsche 911 Turbo S 2012:

• (under engine, on oil pan) oil level sensor
• Actuation
• Bridge plug (relay support 1)
• Can drv high
• Can drv low
• Charge air pressure positioner 1
• Computer data lines system
• Fuse f6 15a
• Fuse f9 25a
• Fuse holder a
• Fuse holder c
• Gnd sens
• Gnd sens 1
• Gnd sens 2
• Gp8 (left rear of engine compt)
• Gp9 (right rear of engine compt)
• Ground
• Hot at all times
• Hot w/ term 15 relay energized
• Intake air pressure/ temperature sensor
• Left mount 2 unit
• Left valve +
• Left valve -
• Mounts control unit
• Nca
• Ntc
• Position
• Pressure sig
• Pwm sig
• Red
• Right mount 1 unit
• Right valve +
• Right valve -
• Sensor +
• Sig
• Signal
• Signal sens 1
• Signal sens 2
• Sply sens 1
• Sply sens 2
• Term 15
• Term 30
• Term 31
• Valve +
• Valve -
• X024
• X592
• X593

3.8L Twin Turbo, Engine Performance Wiring Diagram (5 of 5) for Porsche 911 Turbo S 2012

List of elements for 3.8L Twin Turbo, Engine Performance Wiring Diagram (5 of 5) for Porsche 911 Turbo S 2012:

• (intake manifold) throttle valve
• (right side of engine) (w/ temperature sensor) oil pressure sensor
• (top of cylinders)
• (top of cylinders) fuel injectors
• +5v
• Bank 1
• Camshaft adjuster b1
• Camshaft b2
• Charge air pressure
• Charge air pressure/ temperature sensor
• Charge air temp
• Control valve
• Cooling water
• Cylinder 1
• Cylinder 2
• Cylinder 6
• Dme control unit (left front of engine compt)
• Engine compt
• Gp9 (right rear of engine compt)
• Ground, sensors
• High pressure sens
• Ignition coil cylinder
• Injector, cylinder 1
• Injector, cylinder 1+
• Injector, cylinder 2+
• Injector, cylinder 3
• Injector, cylinder 3+
• Injector, cylinder 4
• Injector, cylinder 4+
• Injector, cylinder 5+
• Injector, cylinder 6
• Injector, cylinder 6+
• Knock sensor 1
• Knock sensor 2
• Nca
• Ntc
• Ntc coolant temperature sensor (engine)
• Ntc engine compartment temperature sensor (middle of engine)
• Oil press
• Oil pressure sens
• Oil temp sens
• Plug spark
• Positioner 1
• Positioner 2
• Pressure sensor
• Pressure sig
• Pressure signal
• Rail pressure sensor
• Sensor gnd
• Shield
• Sig
• Spark plug
• Tank valve
• Term 31
• Term. 31
• Throttle valve
• Valve control b1
• Valve control b2
• X591
• X592
• X593