ENGINE PERFORMANCE
3.1L
3.1L (VIN M), Engine Performance Wiring Diagrams (1 of 4) for Chevrolet Lumina 1998
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO
List of elements for 3.1L (VIN M), Engine Performance Wiring Diagrams (1 of 4) for Chevrolet Lumina 1998:
- (eng harn, on right side of eng compt, 15 cm from pcm breakout)
- (lower left front of eng)
- (pin 10-12 not used)
- (pin 21-27 not used)
- (pin 39-42 not used)
- (pin 49-52 not used)
- (pin 61-63 not used)
- 1-2 ss valve control
- 2-3 ss valve control
- 3x ref high
- 3x ref low (ground)
- Anti-theft system
- Bypass control
- Camshaft position sensor (front of eng, below intake plenum)
- Charge ind control
- Ckp sensor signal
- Cmp signal
- Cooling fan system
- Crankshaft position sensor (24x) (at end of crankshaft behind harmonic balancer)
- Crankshaft position sensor (7x) (lower right side of eng)
- Cruise control system
- Cruise disable output
- Data link connector (below dash, right of steering column)
- Ecm bat fuse 20a
- Ecm ign fuse 15a
- Egr val control (gnd)
- Eleck ign fuse 15a
- Engine wiring harness junction block 1 (forward of right strut tower)
- Evap purge val drviver
- F/injn fuse 15a
- Fuel inj #1 driver
- Fuel inj #2 driver
- Fuel inj #3 driver
- Fuel inj #5 driver
- Fuel inj #6 driver
- Fuel level level ctrl
- Fuse 10a
- Fuse 5a
- Fuse block (on behind right side of dash)
- G110
- High speed fans control
- Hos1 low
- Hos2 low
- Hot at all times
- Hot coolant ind control
- Hot in off, run bulb test, or start
- Hot in run, bulb test or start
- Iac coil b high
- Iat sensor ground
- Ic control
- Ignition control module (top right side of eng)
- Ignition wake up power
- Instrument cluster system
- Knock sensor (lower left side of eng block, above starter)
- Knock sensor signal
- Low speed fans control
- Maf sensor signal
- Nca
- Pcm ground
- Pnk
- Pnk b
- Power (battery)
- Powertrain control module (on right side of eng compt, forward of strut tower)
- S102
- S106
- S142
- S146
- S155
- S156
- S237
- Serial data (class 2)
- Serial data (uart)
- Spark plugs
- Starting/ charging system
- Tan
- Tcc brake switch input
- Theft deter fuel enable
- Tr switch input b
- Vss high
- Vss low
- Vss output
3.1L (VIN M), Engine Performance Wiring Diagrams (2 of 4) for Chevrolet Lumina 1998
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO すべての配線図にアクセスする車
List of elements for 3.1L (VIN M), Engine Performance Wiring Diagrams (2 of 4) for Chevrolet Lumina 1998:
- (lower left front of eng)
- Evaporative emissions canister purge solenoid valve (on top right of eng, on intake plenum)
- Evaporative emissions canister vent solenoid valve (behind left side of rear fascia splash shield, behind wheelwell)
- Fuel injectors
- G110
- Pnk
- S106
- S109
- Stop lamp switch (on brake pedal support c2 bracket)
- Tan
- Transaxle range switch (top of transaxle)
- Vehicle speed sensor (on right rear of eng compt, end of transaxle)
3.1L (VIN M), Engine Performance Wiring Diagrams (3 of 4) for Chevrolet Lumina 1998
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO すべての配線図にアクセスする車
List of elements for 3.1L (VIN M), Engine Performance Wiring Diagrams (3 of 4) for Chevrolet Lumina 1998:
- (eng harn, above ignition control module, 2 cm from ignition control module c2 breakout)
- (eng harn, below eng coolant fans, 13 cm from eng coolant fan 2 breakout)
- (eng harn, below intake plenum, 2 cm from pcm breakout)
- (eng harn, on right side of eng compt, 15 cm from pcm breakout)
- (fuel harn, below rear of vehicle)
- (in center of eng oil pan) engine oil level sensor
- (on air intake, on rear of eng) mass air flow sensor
- (on throttle body assembly) idle air control (iac) valve
- A/c refrigerant pressure sensor (on left front of eng compt, on a/c line)
- C10
- Engine coolant temperature (ect) sensor (near coolant outlet, left rear of eng)
- Exhaust gas recirculation valve (top rear of eng)
- Fuel tank pressure sensor (in fuel tank)
- G110 (lower left front of eng)
- Instrument cluster
- Intake air temperature (iat) sensor (in air cleaner canister)
- Malfunction indicator lamp
- Manifold absolute pressure sensor (on top of eng, on intake plenum)
- Pnk
- Red
- S106
- S107
- S121
- S122
- S167
- S425
- Tan
- Throttle position sensor (on throttle body assembly)
3.1L (VIN M), Engine Performance Wiring Diagrams (4 of 4) for Chevrolet Lumina 1998
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO すべての配線図にアクセスする車
List of elements for 3.1L (VIN M), Engine Performance Wiring Diagrams (4 of 4) for Chevrolet Lumina 1998:
- (at base of left "b" pillar)
- (lower left front of eng)
- (pin 12-15 not used)
- (pin 19-21 not used)
- (pin 29-32 not used)
- (pin 45-48 not used)
- (pin 51-54 not used)
- (pin 62-65 not used)
- (pin 74-77 not used)
- 1-2 shift solenoid
- 2-3 shift solenoid
- 5v ref a
- A/c compress clutch rly
- A/c refrig press signal
- A/c request signal
- Air conditioning system
- Auto transaxle fluid temperature sensor
- Change oil soon ind
- Cmp/ckp sensor batt (+)
- Cmp/ckp sensor ground
- Cruise control system
- Cruise engaged input
- Ecm bat fuse 20a
- Ect sensor signal
- Egr pintle position signal
- Egr val ign positive volt
- Eng oil level ind in
- Engine wiring harness junction block 1 (forward of right front strut tower)
- Evap can vent sol driver
- Fuel inj #4 driver
- Fuel level sensor
- Fuel level sensor input
- Fuel pump
- Fuel pump relay
- Fuel pump relay control
- Fuel tank
- Fuel tank press signal
- Fuse 10a
- Fuse block (on right side of dash)
- G110
- G110 (lower left front of eng)
- G308
- Gen terminal l output
- Heated oxygen sensor (ho2s) 1 (in exhaust manifold, right side of eng)
- Heated oxygen sensor (ho2s) 2 (in exhaust system, behind catalytic converter)
- Ho2s 1 signal
- Ho2s 2 signal
- Hot at all times
- Hot in run, bulb test or start
- Hot in run, bulb test, or start
- Iac coil a high
- Iac coil a low
- Iac coil b low
- Iat sensor signal
- Instrument cluster system
- Low oil level ind control
- Map sensor signal
- Mil control
- Nca
- Pnk
- Pnk e
- Powertrain control module (on right side of eng compt, forward of strut tower)
- Red
- S102
- S105
- S106
- S209
- S305
- Starting/ charging system
- Tach control
- Tan
- Tcc pwm sol val control
- Tcc pwm solenoid
- Tcc solenoid
- Tcc valve control
- Tft sensor signal
- Tp sens or signal
- Tr switch input a
- Tr switch input c
- Tr switch input d
- Trans fuse 10a
- Transaxle
3.8L
3.8L (VIN K), Engine Performance Wiring Diagrams (1 of 4) for Chevrolet Lumina 1998
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO すべての配線図にアクセスする車
List of elements for 3.8L (VIN K), Engine Performance Wiring Diagrams (1 of 4) for Chevrolet Lumina 1998:
- (i/p harn, below i/p compt, 5 cm from blower motor relay breakout)
- (ign harn, top of eng, near ign control module)
- (lower left front of eng)
- (pin 10-14 not used)
- (pin 23-27 not used)
- (pin 39-42 not used)
- (pin 49-52 not used)
- (pin 66-67 not used)
- 1-2 ss valve control
- 18x ref signal
- 2-3 ss valve control
- 3x ref high
- 3x ref low (ground)
- Anti-theft system
- At/iss sensor high
- At/iss sensor low
- Bank 1 knock sensor (lower left side of eng block, above starter)
- Bank 2 knock sensor (lower right side of eng block, below exhaust manifold)
- Bypass control
- Camshaft position sensor (on front of eng, above right side of crankshaft
- Charge ind control
- Cmp signal
- Cooling fans system
- Crankshaft position sensor (at end of crankshaft, behind harmonic balancer)
- Cruise control system
- Cruise disable output
- Data link connector (below dash, right of steering column)
- Ecm bat fuse 20a
- Ecm ign fuse 15a
- Egr val control (gnd)
- Eleck ign fuse 15a
- Engine wiring harness junction block 1 (forward of right strut tower)
- Evap purge val drviver
- F/injn fuse 15a
- Fuel inj 1 driver
- Fuel inj 2 driver
- Fuel inj 4 driver
- Fuel inj 5 driver
- Fuel inj 6 driver
- Fuel level level ctrl
- Fuse 10a
- Fuse 5a
- Fuse block (on right side of dash)
- G110
- High speed fans control
- Hos1 low
- Hos2 low
- Hot at all times
- Hot coolant ind control
- Hot in off, run bulb test, or start
- Hot in run, bulb test or start
- Iac coil b high
- Iat sensor ground
- Ic control
- Ignition control module (top left front of eng)
- Ignition wake up power
- Instrument cluster system
- Knock sensor signal
- Low speed fans control
- Maf sensor signal
- Pcm ground
- Pnk
- Pnk p
- Power (battery)
- Powertrain control module (on right side of eng compt, forward of strut tower)
- Pulley)
- S102
- S106
- S142
- S144
- S145
- S156
- S237
- Serial data (class 2)
- Serial data (uart)
- Spark plugs
- Starting/ charging system
- Tan
- Tcc brake switch input
- Theft deter fuel enable
- Tr switch input b
- Trans fluid press sw a
- Vss high
- Vss low
- Vss output
3.8L (VIN K), Engine Performance Wiring Diagrams (2 of 4) for Chevrolet Lumina 1998
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO すべての配線図にアクセスする車
List of elements for 3.8L (VIN K), Engine Performance Wiring Diagrams (2 of 4) for Chevrolet Lumina 1998:
- (lower left front of eng)
- Evaporative emissions canister purge solenoid valve (on top left side near center of valve cover)
- Evaporative emissions canister vent solenoid valve (behind left side of rear fascia splash shield, behind wheelwell)
- Fuel injectors
- G110
- Pnk
- S106
- S109
- Stop lamp switch (on brake pedal support c2 bracket)
- Tan
- Transaxle range switch (top of transaxle)
- Vehicle speed sensor (on right rear of eng compt, end of transaxle)
3.8L (VIN K), Engine Performance Wiring Diagrams (3 of 4) for Chevrolet Lumina 1998
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO すべての配線図にアクセスする車
List of elements for 3.8L (VIN K), Engine Performance Wiring Diagrams (3 of 4) for Chevrolet Lumina 1998:
- (eng harn, 7 cm from 2-pin conn of right cooling fan breakout)
- (eng harn, below left side of radiator, 15 cm from egr valve)
- (eng harn, left side of eng, near throttle body, 4 cm from maf sensor
- (eng harn, right side of radiator, 20 cm from eng wiring harn junction block breakout)
- (fuel harn, 43 cm from 6-pin conn above fuel tank)
- (in exhaust manifold, right side of eng compt) heated oxygen sensor (ho2s) no1
- (in exhaust system, behind catalytic converter) heated oxygen sensor (ho2s) no2
- (in left side of eng oil pan) engine oil level sensor
- (lower left front of eng)
- (on air intake, on rear of eng) mass air flow sensor
- (on throttle body assembly) idle air control (iac) valve
- A tan
- A/c refrigerant pressure sensor (on left front of eng compt, on a/c line)
- Breakout) s107
- C pnk
- D pnk
- Engine coolant temperature (ect) sensor (near coolant outlet, left rear of eng)
- Exhaust gas recirculation valve (top rear of eng)
- Fuel tank pressure sensor (in fuel tank)
- G110
- G110 (lower left front of eng)
- Intake air temperature (iat) sensor (in air cleaner canister)
- Manifold absolute pressure sensor (on top of eng, on intake plenum)
- Nca
- Pnk
- Red
- S105
- S106
- S121
- S122
- S167
- S425
- Tan
- Throttle position sensor (on throttle body assembly)
3.8L (VIN K), Engine Performance Wiring Diagrams (4 of 4) for Chevrolet Lumina 1998
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO すべての配線図にアクセスする車
List of elements for 3.8L (VIN K), Engine Performance Wiring Diagrams (4 of 4) for Chevrolet Lumina 1998:
- (at base of left "b" pillar)
- (lower left front of eng)
- (pin 12-15 not used)
- (pin 19-21 not used)
- (pin 30-32 not used)
- (pin 47-48 not used)
- (pin 51-54 not used)
- (pin 62 not used)
- (pin 64-65 not used)
- (pin 70-77 not used)
- 1-2 shift solenoid
- 2-3 shift solenoid
- 5v ref a
- A/c compress clutch rly
- A/c refrig press signal
- A/c request signal
- A/t iss solenoid
- Air conditioning system
- Auto transaxle fluid temperature sensor
- Automatic transaxle fluid pressure manual valve position switch
- C10
- Change oil soon ind
- Cruise control system
- Cruise engaged input
- Ecm bat fuse 20a
- Ect sensor signal
- Egr pintle position signal
- Egr val ign positive volt
- Eng oil level ind in
- Engine wiring harness junction block 1 (forward of right front strut tower)
- Evap can vent sol driver
- Fuel inj 3 driver
- Fuel level sensor
- Fuel level sensor input
- Fuel pump
- Fuel pump relay
- Fuel pump relay control
- Fuel tank
- Fuel tank press signal
- Fuse 10a
- Fuse block (on right side of dash)
- G110
- G308
- Gen terminal f monitor
- Gen terminal l output
- Ho2s 1 signal
- Ho2s 2 signal
- Hot at all times
- Hot in run, bulb test or start
- Hot in run, bulb test, or start
- Iac coil a high
- Iac coil a low
- Iac coil b low
- Iat sensor signal
- Instrument cluster
- Instrument cluster system
- Low oil level ind control
- Malfunction indicator lamp
- Map sensor signal
- Mil control
- Pc solenoid valve high
- Pc solenoid valve low
- Pnk
- Powertrain control module (on right side of eng compt, forward of strut tower)
- Ps solenoid
- Red
- S102
- S106
- S209
- S305
- Starting/ charging system
- Tach control
- Tan
- Tcc pwm sol val control
- Tcc release switch input
- Tcc solenoid
- Tft sensor signal
- Tp sens or signal
- Tr switch input a
- Tr switch input c
- Tr switch input d
- Trans fluid press sw b
- Trans fluid press sw c
- Trans fuse 10a
- Transaxle