Fiat DOBLO 1.9 JTD 8V Da 10/2000 – DIPPED HEADLAMPS – – MY 2005 – WIRING DIAGRAM, LOCATION COMPONENTS, OPERATIONAL DESCRIPTION – WIRING DIAGRAM, LOCATION COMPONENTS, OPERATIONAL DESCRIPTION

DIPPED HEADLIGHTS - WIRING DIAGRAM Fiat DOBLO 1.9 JTD 8V Da 10/2000

Components - DIPPED HEADLAMPS - Fiat DOBLO 1.9 JTD 8V Da 10/2000

Component code	Description	Reference to the assembly
B001	JUNCTION UNIT
B2	JUNCTION UNIT UNDER DASHBOARD
C10	LEFT FRONT EARTH
C15	DASHBOARD EARTH, DRIVER''S SIDE
E50	INSTRUMENT PANEL
F010	LEFT HEADLAMP
F011	RIGHT HEADLAMP
H001	IGNITION SWITCH
H5	STEERING COLUMN SWITCH UNIT
M001	BODY COMPUTER

DIPPED HEADLIGHTS - COMPONENT LOCATION Fiat DOBLO 1.9 JTD 8V Da 10/2000

すべての配線図にアクセスする車

Component code	Description	Reference to the assembly
B001	JUNCTION UNIT
B2	JUNCTION UNIT UNDER DASHBOARD
C10	LEFT FRONT EARTH
C15	DASHBOARD EARTH, DRIVER''S SIDE
E50	INSTRUMENT PANEL
F010	LEFT HEADLAMP
F011	RIGHT HEADLAMP
H001	IGNITION SWITCH
H5	STEERING COLUMN SWITCH UNIT
M001	BODY COMPUTER

The vehicle is equipped with two specific dipped beam headlamps.The dipped beams are activated by turning a wheel on the stalk switch to the next position after the side light setting (second position).The dipped beams stay on even with the main beams on and are turned off by turning on the fog lamps.The vehicle offers a follow me home function.This strategy allows the dipped beams to be kept on even with the ignition off for a preset time (within two minutes of turning off the engine).This function is particularly useful, for example, after parking the vehicle in a garage or poorly-lit places/areas.The function is activated by means of the left steering wheel stalk (light flasher): each time the stalk is operated, activation of the dipped beams is extended by 30 seconds for up to 5 minutes, after which they turn off automatically.The circuit is protected by two special fuses: one for the right headlamp and one for the left.The dipped beam circuit also enables the operation of certain other functions, e.g. rear fog lamp activation and headlamp alignment control.

The dipped beams are activated by an earth signal from stalk unit H05 when the wheel is operated and reach body computer M01 at pin 4 connector D.With the key of, pin 33 connector F of the body computer receives a signal from the stalk unit that activates the follow me home function.To turn on the dipped beams, body computer M01 activates a relay F1 contained in under-dashboard junction unit B02 that receives a direct power supply protected by fuse F1 contained in under-dashboard junction unit B01 and sends it to the two right and left headlamps.Each line is protected by a fuse in the under-dashboard junction unit B02. F13 for the left headlamp and F12 for the right.An ignition-controlled signal (INT) from ignition switch H01 reaches pin 11 connector E of under-dashboard junction unit B02.The direct signal to the left headlamp is also sent to instrument panel E50 at pin 7 of connector A for functions that require this enablement signal.Instrument panel E50 also communicates with body computer M01 via pins 8 and 9 connector A and receives supply lines at pins 1 and 3 connector A. It also receives an earth signal at pin 2 connector A.In the Natural Power (1.6 16v Bipower) version, the direct signal to the left headlamp is also sent to instrument panel E50 at pin 6 of connector A for functions that require this enablement signal.Instrument panel E50 also communicates with body computer M01 via pins 4 and 3 connector A and receives supply lines at pins 1 and 2 connector A. It also receives an earth signal at pin 7 connector A.The left headlamp signal and right headlamp signals are both used to operate the headlamp alignment corrector.For further details,