DescriptionThe vehicle has two additional fog lights in the front bumper.The fog lights are activated through a button in the control panel to the left of the steering wheel; when the lights are on the warning light in the instrument panel comes on.A special relay, in the engine compartment control unit, controls the switching on of the fog lights via a line protected by a special fuse.The relay is managed by the Body Computer: the relay is energized in the following conditions:go ahead signal with key in ON position (INT);signal coming from the switchside lights on signal.In addition, if the side lights are switched off, the fog lights are also switched off even if the button is pressed. When the side lights are switched on again, the fog lights do not come on again automatically, but only if the button is still pressed.If the ignition key is switched OFF and then turned back to the ON position, the operating button must be pressed once again in order to turn the fog lights back on.
Functional description The fog lights activated (earth) signal reaches pin 20 of connector H of M1 from the control button in the panel to the left of the steering wheel H91. The side lights activated signal is sent to pin 28 of connector G of the Body Computer M1 from the steering column switch unit H52399168SeeE2010SIDE LIGHTS / NO. PLATE LIGHTS . The Body Computer M1 controls the supply for the fog lights by sending an earth signal to the engine compartment junction unit B1 from pin 8 of connector A of M1 which energizes the relay T14: this supplies the fog lights F15 (left) and F16 (right). The circuit is protected by fuse F30 of control unit B2. The Body Computer M1 is connected, via the CAN line, to the instrument panel E50 to manage the fog lights on warning light.
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid and disconnectthe battery.1. Undo the nut.2. Move aside the retainer.3. Remove the battery carefully.2050795
5530B22
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212400577-5530B10battery - r+r2400580-5530B52Battery DRIP TRAY/SUPPORT - R.R.Open the bonnet lid.1. Disconnect the electrical connection (1a) from the negative batteryterminal (1b).2. Disconnect the electrical connection from the bodyshell3. Disconnect the electrical connection from the gearbox casing.4. Keep the battery earth lead.2050796
5530B36
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Place the vehicle on a lift.Raise the car.1. Undo the nut (1a) and disconnect the electrical connections (1b,1c) from the starter motor.2050797
5530B52
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212400577-5530B10battery - r+r1. Open the retaining bands and release the wiring.2. Remove the battery support tray (2a), releasing the dischargepipe (2b) from the passage hole (2c). 3. Undo the bolts.4. Remove the battery cage.2050799
5530B60
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Undo the nut.2. Undo the retaining buttons using the special tool3. Remove the belt.2050800
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b).2050746
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212400802-7040A37fuse box cover - r r1. Disconnect the electrical connections (1a, 1b, 1c, 1d, 1e, 1f).2. Undo the bracket retaining bolt.3. Slightly move the bracket (3a) for the dashboard trim and undothe bolt (3b).4. Undo the other bolts securing the body computer/junction unit.5. Slightly move the body computer/junction unit assembly.6. Disconnect the electrical connections (6a, 6b, 6c).7. Recover the body computer/junction unit.2050752
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect electronic control unit electrical connections (1a),(1b), (1c).2. Undo the bolts.3. Recover the control unit.2050753
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect electronic control unit electrical connections (1a),(1b), (1c).2. Undo the bolts.3. Recover the control unit.2050754
Prepare the vehiclecomplete with spare wheel, tools, fluids, fuel reserve and driveron board. Check that the tyre inflation pressureis correct.Place the headlamp alignment switch inposition '0'.Position the vehicle on a flat surface,perpendicular to a screen or an opaque surface, 10 metres away,which contains the following lines. 1. V - V: vertical line corresponding to the plot of the plane ofsymmetry of the vehicle.2. C - C: plots of the vertical planes passing through the referencecentres of the lights clusters. 3. HC - HC: horizontal line corresponding to the height from theground of the reference centres for the lights clusters. 4. AC - AC: horizontal line 12 cm below the HC - HC line.5. Lines inclined at 15° as illustrated in the diagram.2050815
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Rotate in an anti-clockwise direction and withdraw the cover.2050805
5540B25
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Turn the cover retainer.2. Remove cover (2a), releasing the retainers (2b).2050808
5540B26
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Turn the cover retainer.2. Remove cover (2a), releasing the retainers (2b2050811
5540B28
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Turn the cover retainer.2. Remove cover (2a), releasing the retainers (2b).2050813
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Undo the bolts.2. Remove the trim (2a) releasing the retainers (2b).2051090
7040A26
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Undo the bolts.2. Remove the bottom trim (2a). To facilitate trim removal, movethe steering column after releasing the steering column positionadjustment lever (2b). 3. Undo the bolts.4. Remove the top trim.2051091
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Undo the cover bolts.2. Remove the cover (2a) by undoing the retainers (2b).2051094
7040A44
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Remove the trim (1a) releasing the inner retainers (1b) usingthe special tool.2051095
7040A45
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Remove the trim (1a) releasing the inner retainers (1b) usingthe special tool.2051096
7040A56
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212400802-7040A37fuse box cover - r r1. Undo the bolt.2. Move the trim (2a) by undoing the internal retainers (2b).3. Disconnect the electrical connections of the switch unit.4. Recover the panel with the switches.2051097
7040A65
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Undo the bolt.2. Remove closure (2a) by undoing internal retainers (2b).2051099
7040A78
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Extract compartment (1a) slightly after undoing retainers (1b).2. Disconnect the radio electrical connection.3. Disconnect the aerial lead connection.4. Recover the compartment2051100
7040A96
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Open the flap.2. Undo the bolts.3. Remove the door.2051101
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Čeština
Dansk
Deutsch
Ελληνικά
English
English
Español
Suomi
Français
Français
עברית
Hrvatski
Magyar
Italiano
한국어
Nederlands
Polski
Português
Português
Română
Русский
Slovenčina
Slovenščina
Svenska
Türkçe
中文 (中国)
