Fiat MULTIPLA 1.6 16v fino a 05/99 – HEADLAMP AGLINMENT CORRECTOR – – WIRING DIAGRAM, LOCATION COMPONENTS, OPERATIONAL DESCRIPTION – WIRING DIAGRAM, LOCATION COMPONENTS, OPERATIONAL DESCRIPTION

Wiring diagram - HEADLAMP AGLINMENT CORRECTOR - Fiat MULTIPLA 1.6 16v fino a 05/99

HEADLIGHT ALIGNMENT ADJUSTMENT - WIRING DIAGRAM Fiat MULTIPLA 1.6 16v fino a 05/99

COMPONENTS - HEADLAMP AGLINMENT CORRECTOR - Fiat MULTIPLA 1.6 16v fino a 05/99

Component code	Description	Reference to the assembly
B1	Junction unit
B5	MAXI FUSE box
C10	Left front earth	-
C11	Front earth right	-
C15	Facia earth, driver's side	-
C20	Passenger side dashboard earth	-
D1	Front/facia junction	-
H1	Ignition switch
H5	Stalk unit
H15	Headlamp alignment control
J45	Dipped beam maintenance relay	-
F10	Left headlamp
F11	Right headlamp

Component location - HEADLAMP AGLINMENT CORRECTOR - Fiat MULTIPLA 1.6 16v fino a 05/99

HEADLIGHT ALIGNMENT ADJUSTMENT - COMPONENT LOCATION Fiat MULTIPLA 1.6 16v fino a 05/99

すべての配線図にアクセスする車

COMPONENTS - HEADLAMP AGLINMENT CORRECTOR - Fiat MULTIPLA 1.6 16v fino a 05/99

Component code	Description	Reference to the assembly
B1	Junction unit
B5	MAXI FUSE box
C10	Left front earth	-
C11	Front earth right	-
C15	Facia earth, driver's side	-
C20	Passenger side dashboard earth	-
D1	Front/facia junction	-
H1	Ignition switch
H5	Stalk unit
H15	Headlamp alignment control
J45	Dipped beam maintenance relay	-
F10	Left headlamp
F11	Right headlamp

Description - HEADLAMP AGLINMENT CORRECTOR - Fiat MULTIPLA 1.6 16v fino a 05/99

The headlight light beam can be adjusted directly from the driver's seat depending on the load. The correct headlamp alignment is quickly achieved in this way. The adjustment device takes the form of a motor fitted on both dipped beams. It is able to tilt the headlamps to lower the light beam if the car is particularly loaded and raise the lamps when the load reduces. A special knob located in the dashboard, to the right of the steering wheel, can be placed in four different positions: position 0 - up to three persons in the front seats;position 1 - six persons;position 2 - six persons plus load in the luggage compartment;position 3 - driver plus maximum permitted load all stowed in the luggage compartment.The device is enabled only with the dipped beams on.The headlamp alignment circuit is protectd by the dipped headlamp circuit fuses located in the junction unit.

Operational description - HEADLAMP AGLINMENT CORRECTOR - Fiat MULTIPLA 1.6 16v fino a 05/99

The headlight alignment device H15 receives a supply at pin 2 - with the dipped headlights on - from a line coming from the steering column switch unit H5 : the supply is ignition operated (INT/A) for the line protected by fuse F5 from the junction unit B1 via a special relay J45 . Pin 4 of the device H15 is earthed, whilst a signal leaves pin 1 and reaches pin 7 of the headlights F10 (left) and F11 (right,produced by means of a resistive distributor which varies the output tension depending on which of the four positions is selected. The motors located in the headlights F10 (left) and F11 (right) are supplied at pins 3, pins 6 of F10 and F11 by the same line for the dipped headlights circuit, line protected by fuse F5 from the junction unit B1 . The device only works with the dipped beams on.