Fiat ULYSSE 2.2 16V JTD fino a 04/03 – WINDSCREEN WASH/WIPE – – MY 2005 – WIRING DIAGRAM, LOCATION COMPONENTS, OPERATIONAL DESCRIPTION – WIRING DIAGRAM, LOCATION COMPONENTS, OPERATIONAL DESCRIPTION

WINDSCREEN WASH/WIPE WIRING DIAGRAM Fiat ULYSSE 2.2 16V JTD fino a 04/03

Components - WINDSCREEN WASH/WIPE - Fiat ULYSSE 2.2 16V JTD fino a 04/03

Component code	Description	Reference to the assembly
A001	BATTERY	-
B001	ENGINE COMPARTMENT JUNCTION UNIT
C011	RIGHT FRONT EARTH	-
C015	DRIVER''S DASHBOARD EARTH	-
C020	PASSENGER SIDE DASHBOARD EARTH	-
D006	FRONT/REAR COUPLING	-
D020	DASHBOARD/REAR COUPLING	-
H001	Ignition switch
M001	BODY COMPUTER
M093	STEERING WHEEL NODE CONTROL UNIT (NVO)
K125	RAIN AND DUSK SENSOR
N015	WINDSCREEN WIPER MOTOR
N022	WINDSCREEN/REARSCREEN ELECTRIC WASHER PUMP MOTOR

WINDSCREEN WASH/WIPE COMPONENT LOCATION Fiat ULYSSE 2.2 16V JTD fino a 04/03

すべての配線図にアクセスする車

Component code	Description	Reference to the assembly
A001	BATTERY	-
B001	ENGINE COMPARTMENT JUNCTION UNIT
C011	RIGHT FRONT EARTH	-
C015	DRIVER''S DASHBOARD EARTH	-
C020	PASSENGER SIDE DASHBOARD EARTH	-
D006	FRONT/REAR COUPLING	-
D020	DASHBOARD/REAR COUPLING	-
H001	Ignition switch
M001	BODY COMPUTER
M093	STEERING WHEEL NODE CONTROL UNIT (NVO)
K125	RAIN AND DUSK SENSOR
N015	WINDSCREEN WIPER MOTOR
N022	WINDSCREEN/REARSCREEN ELECTRIC WASHER PUMP MOTOR

The windscreen wash/wipe system is activated by the lever located on the right of the steering wheel, with the following functions: There are five possible positions for the lever, turning it in a clockwise direction, corresponding to:windscreen wiper off (stationary);automatic operation;continuous slow operation;continuous fast operation;"antipanic" temporary fast operation (unstable position, turning the lever in an anti-clockwise direction).In the automatic operation position, thanks to the rain sensor, the frequency of the windscreen wiper strokes can be adapted to suit the intensity of the rain. The frequency of the windscreen wiper strokes is automatically adjusted depending on the amount of water on the windscreen detected by the sensor: the frequency varies continuously from nil (no stroke - windscreen dry) to wiping at the second continuous speed (heavy rain).767Activating the windscreen washers with the rain sensor activated produces the normal washing cycle at the end of which the rain sensor resumes its normal automatic operation.The windscreen washer function can be activated by pulling the lever toward the steering wheel: the windscreen washer pump is activated in this way; keeping the lever pulled switches on the windscreen wiper for a three stroke cycle.A check on the functions described above is carried out by the body computer node which produces the intermittent function, controls the operation of the windscreen wiper motor and the windscreen washer pump and manages the rain sensor.The windscreen wiper and the windscreen washer can be activated with the key in position M.767To facilitate maintenance, with the ignition key in position S or extracted, if the lever is turned downwards within 60 seconds, the windscreen wipers assume a vertical position and stop; they can be raised to replace the blades or for cleaning.769If the windscreen wiper is activated, the lights come on automatically if this device is switched on.

The steering wheel node control unit m093 receives a power supply (pin 5 connector A and pin 4 connector D) from the Body computer node M001 (pin 11 connector B and pin 1 connector G respectively) via two lines only the second of which is protected by fuse F04.The command to switch on the windscreen wiper and windscreen washer is supplied by the Steering wheel node control unit M093 (pins 1 and 3 of connector A) to the Body computer node M001 (pins 5 and 3 of connector G respectively). The signal travels via the CAN line.The Body computer node M001, in turn, transmits the signal (pins 25 and 27 of connector E), via the CAN line, to the engine compartment junction unit B001 (pins 12 and 11 respectively of connector F).The engine compartment junction unit B001 provides a power supply (pin 28 connector F) for the windscreen wiper motor N015 (pin 4) via a line protected by fuse F12.When the windscreen wiper motor N015 reaches the end of travel position an earth signal is sent from pin 2 to pin 25 of connector F of the engine compartment junction unit B001.The latter, once the signal has been received, switches the power supply from pin 28 of connector F to pin 27 of the same connector, providing a power supply at pin 5 for the windscreen wiper motor N015 and allowing it to return to the rest position.The rain and dusk sensor K125 is connected to earth C020 at pin 3 and sends the information relating to the weather conditions (pins 2 and 4), via the CAN line, to the Body computer node M001 (pins 24 and 26 connector L). There is also a power supply at pin 1 from the Body computer N001 via pin 3 of connector H.The electric motor N022 carries out the dual windscreen and rearscreen washing function. There is a power supply at pin 2 from the engine compartment junction unit B001 (pin 2 connector G) through a line protected by fuse F03 and a return at pin 1 connected to the same junction unit (pin 5 connector G).