ENGINE PERFORMANCE
2.7L
2.7L, Engine Performance Wiring Diagram (1 of 4) for Toyota Sienna SE 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO List of elements for 2.7L, Engine Performance Wiring Diagram (1 of 4) for Toyota Sienna SE 2011:
- (left side of engine compt)
- (under left front seat) k1
- +b2
- +bm
- A/f fuse 20a
- A/f htr relay
- A2 (left front of engine compt)
- A30
- A46
- A55
- Accelerator position sensor (accelerator pedal assembly) (accelerator pedal assembly)
- Ad4
- Anti-theft system
- Ba2
- Batt
- C/opn relay
- Camshaft timing oil control valve (bank 1 exhaust side) (top front of engine)
- Camshaft timing oil control valve (bank 1 intake side) (top front of engine)
- Canh
- Canl
- Ccs
- Computer data lines system
- Cooling fans system
- Cruise control system
- D7 (center of dash)
- Ecm (left rear of engine compt)
- Ect fuse 7.5a
- Efi 1 fuse 25a
- Efi 2 fuse 15a
- Efi main relay
- Engine room r/b (left side of engine compt)
- Epa
- Epa2
- Etcs fuse 10a
- F34
- Fuel sender gauge assembly
- Gauge
- Hot at all times
- Igsw
- Imi
- Imo
- Instrument cluster system
- Instrument panel j/b (left side of dash)
- J/c a46 & b44 (left side of engine compt) b44
- J/c a46 (left side of engine compt)
- J/c a49
- J/c b44 (left side of engine compt)
- J/c d105 (center of dash)
- Ka2
- Mpmp
- Mrel
- Neo
- Park/neutral position switch assembly (transaxle assembly)
- Pnk
- Pump
- Red
- Rfl
- Sftd
- Sftu
- Spd
- St-
- Sta
- Starting/charging system
- Stp
- Tach
- Transmission control ecu assembly (left front of engine compt)
- Transmission control switch
- Vcp2
- Vcpa
- Vpa
- Vpa2
- Vpmp
- Gk1
2.7L, Engine Performance Wiring Diagram (2 of 4) for Toyota Sienna SE 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 모든 배선 다이어그램에 액세스하십시오.List of elements for 2.7L, Engine Performance Wiring Diagram (2 of 4) for Toyota Sienna SE 2011:
- (above brake pedal) stop light switch assembly
- (left rear of vehicle chassis)
- A44
- A55
- Acis
- Ad4
- Aicv
- Alt
- B4 (rear of engine)
- B45
- B5 (rear of engine)
- Ba1
- Ba2
- Can+
- Can-
- Canister pressure sensor
- Canister pump module
- Computer data lines system
- E04
- Ecm (left rear of engine compt)
- F26
- F29
- F35
- F36
- Gauge 1 fuse 10a
- Gauge 2 fuse 7.5a
- Ge01
- Ha1a
- Hot at all times
- Hot in on or start
- Ht1b
- Ia1+
- Ia1-
- Ig2 fuse 7.5a
- Igf1
- Instrument panel j/b (left side of dash)
- J/c a46 (left side of engine compt)
- J/c a48 (left side of dash)
- J/c d100 (left side of dash)
- Ka2
- Leak detection pump
- Lines system computer data
- Me01
- Mgnd
- Mtrb
- Nsw
- Oc1+
- Oc1-
- Oe1+
- Oe1-
- Pbv
- Pnk
- Prg
- Red
- Sgnd
- Shift lock fuse 7.5a
- Starting/ charging system
- Stop fuse 10a
- Vcc
- Vent valve
- Vgnd
- Vlvb
- Vout
- Gk2
2.7L, Engine Performance Wiring Diagram (3 of 4) for Toyota Sienna SE 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 모든 배선 다이어그램에 액세스하십시오.List of elements for 2.7L, Engine Performance Wiring Diagram (3 of 4) for Toyota Sienna SE 2011:
- (intake manifold assembly) throttle w/ motor body assembly
- A/t/odo lcd
- A/t/odo/acc lcd
- A2 (left front of engine compt)
- A46
- Ad4
- Anti-lock brakes system
- B4 (rear of engine)
- B44
- Ba1
- Ba2
- Buzzer
- Bf2
- Canh
- Canl
- Chk
- Combination meter assembly
- Computer data lines system
- D6 (center of dash)
- Dome fuse 7.5a
- Engine room r/b (left side of engine compt)
- Except option meter
- Hot at all times
- Ig+
- Ig2
- Ig2 relay
- Ind lamp malfunction
- Inj fuse 25a
- J/c a46 & b44 (left side of engine compt)
- J/c a52 (left side of engine compt)
- J/c d96 (left side of dash)
- J/c d99 (left side of dash)
- Knock control sensor (bank 1) (rear of engine)
- Micro processor
- Nca
- Option meter
- Pnk
- Purge vsv (rear of engine compt)
- Red
- Vsv (acis) (right rear of engine compt)
- Vsv (air intake control) (rear of engine)
- Vsv (ejector) (rear of engine compt)
- Vta
- Vta2
2.7L, Engine Performance Wiring Diagram (4 of 4) for Toyota Sienna SE 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 모든 배선 다이어그램에 액세스하십시오.List of elements for 2.7L, Engine Performance Wiring Diagram (4 of 4) for Toyota Sienna SE 2011:
- (front of crankshaft assembly) crank position sensor
- (front of engine)
- (intake assembly) intake air control valve actuator
- (rear of cylinder head) vvt sensor (bank 1 intake side)
- (rear of engine) b4
- (rear of engine) b5
- (rear of engine) efi engine coolant temperature sensor
- (rear of engine) vvt sensor (bank 1 exhaust side)
- (top of engine) fuel injector assembly 1
- (top of engine) fuel injector assembly 2
- (top of engine) fuel injector assembly 3
- (top of engine) fuel injector assembly 4
- A1a+
- A1a-
- Ad4
- Air fuel ratio sensor (bank 1 sensor 1) (base of exhaust manifold assembly)
- B4 (rear of engine)
- B45
- Ba1
- Ba2
- Ba6
- Bf2
- E01
- E02
- E03
- E2g
- Ecm (left rear of engine compt)
- Eia1
- Eknk
- Eppm
- Eta
- Etha
- Ethw
- Ev1+
- Ev1-
- Ex1b
- G2+
- G2-
- Gnd
- Ht1b
- Iac1
- Igf
- Ignition coil assembly 1 (top of cylinder head)
- Ignition coil assembly 2 (top of cylinder head)
- Ignition coil assembly 3 (top of cylinder head)
- Ignition coil assembly 4 (top of cylinder head)
- Igt1
- Igt2
- Igt3
- Igt4
- Intake mass air flow meter sub assembly (air intake assembly)
- Knk1
- Nca
- Ne+
- Ne-
- Out
- Ox1b
- Oxygen sensor (bank 1 sensor 2)
- Pnk
- Ppmp
- Red
- Tha
- Thw
- Vc2
- Vccp
- Vce1
- Vcta
- Vcv1
- Vdd
- Vta1
- Vta2
- Vve+
- Vve-
- Vvi+
- Vvi-
3.5L
3.5L, Engine Performance Wiring Diagram (1 of 6) for Toyota Sienna SE 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 모든 배선 다이어그램에 액세스하십시오.List of elements for 3.5L, Engine Performance Wiring Diagram (1 of 6) for Toyota Sienna SE 2011:
- +b2
- A/f fuse 20a
- A/f htr relay
- A35
- A39
- A46
- Accelerator position sensor (accelerator pedal assembly)
- Ad4
- Anti-theft system
- B44
- Ba2
- Batt
- Canh
- Canl
- Cann
- Canp
- Ccs
- Compt)
- Computer data lines system
- Cooling fans system
- Cruise control system
- Ecm (right rear of engine compt)
- Ect fuse 7.5a
- Efi 1 fuse 25a
- Efi 2 fuse 10a
- Efi main relay
- Els2
- Engine room r/b (left side of engine c/opn relay
- Epa
- Epa2
- Excd
- Fpr
- Hot at all times
- Ig2d
- Igsw
- Imi
- Imo
- Instrument cluster system
- J/c a46 & b44 (left side of engine compt)
- J/c a48 (left side of dash)
- J/c a49
- Ka2
- La1
- Mpmp
- Mrel
- Neo
- Power management control ecu (w/ smart key system) (right side of dash)
- Red
- Rfc
- Sftd
- Sftu
- Spd
- St1-
- Sta
- Starting/charging system
- Stop light switch assembly
- Stp
- Tach
- Vcp2
- Vcpa
- Voltage inverter assembly (above right rear wheelwell)
- Vpa
- Vpa2
- Vpmp
- Gk2
3.5L, Engine Performance Wiring Diagram (2 of 6) for Toyota Sienna SE 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 모든 배선 다이어그램에 액세스하십시오.List of elements for 3.5L, Engine Performance Wiring Diagram (2 of 6) for Toyota Sienna SE 2011:
- (left rear of engine compt) fuel pump resistor
- (left side of engine compt) engine room r/b
- (left side of engine compt) j/c a46 & b44
- (left side of engine compt) j/c a50
- A14
- A46
- Acc
- Ad2
- B1 (rear of engine)
- B44
- Ba1
- Camshaft timing oil control valve (bank 2 exhaust side) (top front of engine)
- F29
- F35
- F36
- Fuel pmp relay
- Gnd
- Hot at all times
- Ig2 fuse 7.5a
- Igf
- Ignition coil assembly 1 (top of right cylinder bank)
- Ignition coil assembly 2 (top of left cylinder bank)
- Ignition coil assembly 3 (top of right cylinder bank)
- Ignition coil assembly 4 (top of left cylinder bank)
- Ignition coil assembly 5 (top of right cylinder bank)
- Ignition coil assembly 6 (top of left cylinder bank)
- Ignition or starter switch assembly
- Igt1
- Igt2
- Igt3
- Igt4
- Igt5
- Igt6
- Instrument panel j/b (left side of dash)
- Lock
- Off
- Pnk
- Red
- Run
- Start
- Stop fuse 10a
- W/ smart key system
- W/o smart key system
3.5L, Engine Performance Wiring Diagram (3 of 6) for Toyota Sienna SE 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 모든 배선 다이어그램에 액세스하십시오.List of elements for 3.5L, Engine Performance Wiring Diagram (3 of 6) for Toyota Sienna SE 2011:
- (center of dash) d7
- (rear of engine) b2
- +bm
- A2 (left side of engine compt)
- A44
- Ad4
- Alt
- B2 (rear of engine)
- B3 (top of engine)
- Ba1
- Ba2
- Camshaft timing oil control valve (bank 2 intake side) (top front of engine)
- Can+
- Can-
- Computer data lines system
- Dome fuse 7.5a
- Ecm (right rear of engine compt)
- Engine room r/b (left side of engine compt)
- Eo1
- Eo2
- Eo3
- Eo4
- Eo5
- Etcs fuse 10a
- Ge01
- Ha1a
- Ha2a
- Hot at all times
- Hot w/ ig1 2 relay energized
- Ht1b
- Ht2b
- Ig2 relay
- Igt1
- Igt2
- Igt3
- Igt4
- Igt5
- Igt6
- Inj fuse 25a
- Instrument panel j/b (left side of dash)
- J/c a52 (left side of engine compt)
- J/c d105 (center of dash)
- Oc2+
- Oc2-
- Oe2+
- Oe2-
- Pnk
- Red
- Shift lock fuse 7.5a
- Starting/charging system
- Transmission control switch
- W/ smart key system
- W/o smart key system
3.5L, Engine Performance Wiring Diagram (4 of 6) for Toyota Sienna SE 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 모든 배선 다이어그램에 액세스하십시오.List of elements for 3.5L, Engine Performance Wiring Diagram (4 of 6) for Toyota Sienna SE 2011:
- (fuel pump: fuel tank assembly) fuel pump & sender gauge assembly
- A/t/odo lcd
- A46
- A55
- Ad4
- Ba2
- Batt
- Buzzer
- Combination meter assembly
- Computer data lines system
- D6 (center of dash)
- Except optitron meter
- F26
- Gauge
- Gauge 1 fuse 10a
- Gauge 2 fuse 7.5a
- Hot in on or start
- Hot w/ ig1 1 relay energized
- Ig2
- Igsw
- Instrument cluster system
- Instrument panel j/b (left side of dash)
- J/c a46 & b44 (left side of engine b44 compt)
- J/c b44 (left side of engine compt)
- J/c d100 (left side of dash)
- J/c d96 (left side of dash)
- J/c d99 (left side of dash)
- K1 (under left front seat)
- Ka2
- Lcd (a/t/odo lcd)
- Malfunction ind lamp
- Micro computer
- Optitron meter
- Park/neutral position switch assembly (w/o smart key) (transaxle assembly)
- Pnk
- Pump
- Red
- Starting/charging system
- Stp
- Transmission control ecu assembly (left front of engine compt)
- Gk1
3.5L, Engine Performance Wiring Diagram (5 of 6) for Toyota Sienna SE 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 모든 배선 다이어그램에 액세스하십시오.List of elements for 3.5L, Engine Performance Wiring Diagram (5 of 6) for Toyota Sienna SE 2011:
- (air intake assembly) intake mass air flow meter sub assembly
- (downstream of catalytic converter) oxygen sensor (bank 2 sensor 2)
- (intake manifold assembly)
- (left front of engine compt) vsv (acm)
- (rear of engine) purge vsv
- (rear of engine) vsv (air intake control)
- (right rear of engine compt)
- A1a+
- A1a-
- A2a+
- A2a-
- Air fuel ratio sensor (bank 1 sensor 1) (base of left exhaust manifold)
- Air fuel ratio sensor (bank 2 sensor 1) (base of right exhaust manifold)
- B1 (rear of engine)
- Ba1
- Ba2
- Bank)
- Da6
- E2g
- Fuel injector assembly 1 (top of right cylinder
- Fuel injector assembly 2 (top of left cylinder
- Fuel injector assembly 3 (top of right cylinder
- Fuel injector assembly 4 (top of left cylinder
- Fuel injector assembly 5 (top of right cylinder
- Fuel injector assembly 6 (top of left cylinder
- Ha1a
- Ha2a
- Ht2b
- Ka2
- Nca
- Ox2b
- Pnk
- Red
- Tha
- Throttle w/ motor body assembly
- Vsv (acis)
3.5L, Engine Performance Wiring Diagram (6 of 6) for Toyota Sienna SE 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 모든 배선 다이어그램에 액세스하십시오.List of elements for 3.5L, Engine Performance Wiring Diagram (6 of 6) for Toyota Sienna SE 2011:
- (left rear of vehicle chassis) canister pump module
- (left side of engine compt) j/c a46 & b44
- (rear of engine) e.f.i engine coolant temperature sensor
- (top front of engine)
- (top front of engine) camshaft timing oil control valve (bank 1 exhaust side)
- (top front of engine) camshaft timing oil control valve (bank 1 intake side)
- A1a+
- A1a-
- A2a+
- A2a-
- A46
- Acis
- Acm
- Ad4
- Aicv
- B1 (rear of engine)
- B2 (rear of engine)
- B44
- Ba1
- Ba2
- Bf1
- Canister pressure sensor
- Crankshaft position sensor (front of crankshaft assembly)
- E2g
- Ecm (right rear of engine compt)
- Ekn2
- Eknk
- Eta
- Etha
- Ethw
- Ev1+
- Ev2+
- Ex+
- Ex-
- Ex1b
- Ex2b
- Ht1b
- Igf1
- Ka2
- Knk1
- Knk2
- Knock control sensor (bank 1) (top of engine)
- Knock control sensor (bank 2) (top of engine)
- Leak detection pump
- Meo1
- Nca
- Ne+
- Ne-
- Nsw
- Oc1+
- Oc1-
- Oe1+
- Oe1-
- Ox1b
- Ox2b
- Oxygen sensor (bank 1 sensor 2)
- Pnk
- Ppmp
- Prg
- Red
- Starting/ charging system
- Tha
- Thw
- Vc2
- Vcta
- Vcv1
- Vcv2
- Vent valve
- Vta1
- Vta2
- Vv1+
- Vv1-
- Vv2+
- Vv2-
- Vvl+
- Vvl-
- Vvr+
- Vvr-
- Vvt sensor (bank 1 exhaust side) (top left side of engine)
- Vvt sensor (bank 1 intake side)
- Vvt sensor (bank 2 exhaust side) (top right side of engine)
- Vvt sensor (bank 2 intake side) (top front of engine)
- Gk2