DescriptionThe vehicle is equipped with two GAS DISCHARGE headlamps. For more details 3022525Characteristic of working principle5540EXTERIOR LIGHTING . The left headlamp is the Master control unit while the right acts as a Slave unit.The master downloads the dipped beam command, car speed and - to manage the function - signals from two sensors (potentiometric) on the wheel axles that manage front and rear ride.The control unit controls the adjustment motor - located in the headlamps - and tilts it by the required amount on the basis of input.768
767on the version with gas discharge headlamps, the light beam is adjusted automatically and the two buttons on the left side of the panel are no longer active.
The device is enabled only when the dipped beam headlamps are on.The electronics for the two headlamps are supplied by a fuse that protects other supplies controlled by the ignition.
Functional description The ignition-operated power supply (INT) for the electronics of the two headlsmps F10 and F11 reaches pin 6 through the line of fuse F37 of the unit under the dashboard B2, whilst pin 14 of F10 and F11 is earthed. Pins 8 of F10 and F11 are connected to one another (serial communication line between MASTER and SLAVE), whilst pin 13 of the control unit located in headlamp F10 receives the speedometer signal from pin 28 connector A of the Body Computer M1. Headlamp F10 incorporates the headlamp alignment function: the two sensors (potentiometers) that record the alignment at the front K1 and the rear K2 are connected: a supply and reference earth are sent from pins 9 and 10 of F10: the signals proportional to the load return to pins 11 and 12; on the basis of these signals, the electronics for the headlamp automatically adjusts the light beam by means of a special motor (the motor for the left headlamp is adjusted directly, the one for the right headlamps via the serial line between F10A and F11A). Self-diagnostic data can be read by connecting the unit to connector G of Body Computer M1- pin 12: this receives signals from pins 7 of F10 and F11 via the special diagnostic line.
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213025802-7040A37fuse box cover - r r1. Disconnect the electrical connections at the front (1a, 1b, 1c,1d, 1e, 1f).2. Undo the bolts fixing the control unit.3. Undo the bolts shown fixing the dashboard cover.2004865
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Ensure that the ignition key is in the OFF position, then disconnectthe negative battery terminal (-).2. Open the maxi fuse box cover.3. Undo the bolts securing the 'maxi-fuse' box to the battery.4. Loosen the bolt fixing the battery terminal (+).5. Release the maxi fuse box from the battery and move it to theside.2004975
5530B14
Follow these precautions:769768768
5530B18
Follow these precautions.769On batteries with an opticam hydrometer,electrolyte level and battery charge status can be monitored qualitativelyby examining the indicator colour: a light, bright colour indicates low electrolytelevel: top up with distilled water;a dark colour without a green area in thecentre indicates that the electrolyte level is correct but chargeis low: recharge the battery; a dark colour with a green area in themiddle indicates that both electrolyte level and charge status arecorrect: no action is necessary. For further details, see DESCRIPTION ANDOPERATION - 5580.768Proceed as follows.Check the battery voltage without loadusing the test device recommended by the Service outlets (e.g. 'MICRO360'). Depending on the voltage values measured,which define the state of charge of the battery, proceed as follows:If the voltage without load is less than12.10 V, replace the battery (see op.). 5530B10).If the voltage without load is over 12.10V but less than 12.50 V, recharge the battery (see op. 5530B14).If the voltage without load is over 12.50V, the battery is efficient.If necessary, top up the electrolyte asfollows.Carefully remove the cap strip.Top up with distilled and deionized water,taking care not to allow electrolyte to splash out.768
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Place the vehicle on a lift.Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b).2004980
5530B40
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b).2004986
5530B52
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Proceed with removal 3025534-5530B10battery - r+r .1. Remove the relay/fuse box cover.2. Undo the nut (2a) and disconnect the earth lead (2b) from therelay-fuse box.2004990
5530B60
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213025534-5530B10battery - r+r1. Remove the battery drip tray.2. Unscrew bolts (2a) and loosen bolt (2b) securing the batterycradle.3. Move the battery cradle aside.4. Release the belt retaining stud.5. Remove the belt.2005002
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Release the retainers for the switch panel from the dashboardtrim.2. Disconnect the electrical connections.3. Recover the switch panel.2005045
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.
5540B26
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.
5540B38
Prepare the vehiclecomplete with spare wheel, tools, fluids, fuel reserve and driveron board. Check that the tyre inflation pressureis correct.Place the headlamp alignment switch inposition '0'.Position the vehicle on a flat surface,perpendicular to a screen or an opaque surface, 10 metres away,which contains the following lines. 1. V - V: vertical line corresponding to the trace of the planeof symmetry of the vehicle.2. C - C: traces of the vertical planes passing through the referencecentres of the light clusters.3. HC - HC: horizontal line corresponding to the height from theground of the reference centres for the light clusters. 4. AC - AC: horizontal line 10 cm below the HC - HC line.5. Lines inclined at 15° as illustrated in the diagram.2005013
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213025620-5580E08aerial for alpha code- r r1. Disconnect the electrical connections (1a, 1b) from the ignitionswitch.2. Use a drift and undo the headless bolts (2a); remove the ignitionswitch (2b).7682004913
5520A14
769
5520A16
769
5520A18
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. If necessary, regulate the steering wheel height adjustment lever.2. Undo the bolts fixing the lower trim.3. Remove the lower trim, releasing it from the inner retainersand the steering wheel.2004920
Controls for headlamp alignment, instrument lighting adjustment
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Čeština
Dansk
Deutsch
Ελληνικά
English
English
Español
Suomi
Français
Français
עברית
Hrvatski
Magyar
Italiano
日本語
Nederlands
Polski
Português
Português
Română
Русский
Slovenčina
Slovenščina
Svenska
Türkçe
中文 (中国)
