Fiat DUCATO 2.3 JTD 16V fino a 02/05 – OVERTAKING SENSOR – – WIRING DIAGRAM, LOCATION COMPONENTS, OPERATIONAL DESCRIPTION – WIRING DIAGRAM, LOCATION COMPONENTS, OPERATIONAL DESCRIPTION

Wiring Diagram - OVERTAKING SENSOR - Fiat DUCATO 2.3 JTD 16V fino a 02/05

OVERTAKING SENSOR WIRING DIAGRAM Fiat DUCATO 2.3 JTD 16V fino a 02/05

Components - OVERTAKING SENSOR - Fiat DUCATO 2.3 JTD 16V fino a 02/05

Component code	Description	Reference to the assembly
B002	JUNCTION UNIT UNDER DASHBOARD	-
C015	DASHBOARD EARTH, DRIVER'S SIDE	-
D016	ADDITIONAL DASHBOARD/LEFT FRONT DOOR COUPLING	-
D097	SHORT CIRCUITING COUPLING	-
D160	DASHBOARD/OPTIONAL DASHBOARD COUPLING	-
E050	INSTRUMENT PANEL
E080	OVERTAKING SENSOR LED/BEEPER	-
H005	STEERING COLUMN SWITCH UNIT
H090	SWITCH CONTROL PANEL
K150	OVERTAKING SENSOR (MICRO-CAMERA)	-
M130	OVERTAKING SENSOR CONTROL UNIT	-
		-

Components - OVERTAKING SENSOR - Fiat DUCATO 2.3 JTD 16V fino a 02/05

OVERTAKING SENSOR LOCATION COMPONENTS Fiat DUCATO 2.3 JTD 16V fino a 02/05

모든 배선 다이어그램에 액세스하십시오.

Component code	Description	Reference to the assembly
B002	JUNCTION UNIT UNDER DASHBOARD	-
C015	DASHBOARD EARTH, DRIVER'S SIDE	-
D016	ADDITIONAL DASHBOARD/LEFT FRONT DOOR COUPLING	-
D097	SHORT CIRCUITING COUPLING	-
D160	DASHBOARD/OPTIONAL DASHBOARD COUPLING	-
E050	INSTRUMENT PANEL
E080	OVERTAKING SENSOR LED/BEEPER	-
H005	STEERING COLUMN SWITCH UNIT
H090	SWITCH CONTROL PANEL
K150	OVERTAKING SENSOR (MICRO-CAMERA)	-
M130	OVERTAKING SENSOR CONTROL UNIT	-
		-

Description - OVERTAKING SENSOR - Fiat DUCATO 2.3 JTD 16V fino a 02/05

The overtaking sensor is a device located inside the driver''s door mirror (only left-hand drive). This surveys the blind spot on the driver''s side to ensure safer overtaking or lane change manoeuvres.The device monitors the area at the side of the vehicle and notifies the driver of the presence of overtaking vehicles. In particular, the device is able to indicate approaching vehicles in the lane alongside the lane in which the vehicle on which the device is installed is driving. The vehicle fitted with the sensor can detect vehicles up to 20 m away. Notification is by means of a lighted signal that turns into a sound signal when the turn signal is on (left turn signal).Notification begins when the approaching vehicle is still visible in the door mirror. A darkened area on the TV screen demits the image acquisition field to reduce glare.The device consists of:a microcamera inside the door mirror that is positioned to ensure scanning of areas that are otherwise hard to see,a special control unit in the door compartment that can analyse the input signal and transmit a visual signal,- a driver interface (positioned on the driver''s side door inner panel) that includes: an indicator led and an acoustic signal (buzzer).The system notifies the driver of potential danger, e.g. if an overtaking vehicle draws level, by turning on a led. If the turn signals are activated (to indicate an intention to overtake) under conditions of potential danger , the control unit activates the buzzer to warn the driver that the manoeuvre is potentially dangerous.e system is enabled only at speeds higher than 30 km/h. At speeds betwen 30 and 80 km/h, the scanned area is directly proportional to speed. The scanned area reaches its maximum extent at speeds higher than 80 km/h.

Operational Description - OVERTAKING SENSOR - Fiat DUCATO 2.3 JTD 16V fino a 02/05

Parking sensor M130 is supplied with key-on - at pins 6 and 11 - by a line protected by fuses F27 and F35, located in under-facia junction unit B002.The remaining control unit pins are connected as follows:pin 1, 2: power supply and earth of parking TV camerapin 3 : composite video signal input from parking TV camera K150;pin 4 : composite video signal earth reference from parking TV camera K150;pin 5 : earth connection C020;pin 7 : led/acoustic signal unit power supply E080;pin 8 : led control of led/acoustic signal unit E080;pin 9 : buzzer control of led/acoustic signal unit E080;Control unit M130 receives a vehicle speed signal supplied by instrument panel E050 - pin 13 connector E - at pin 10.Control unit M130 receives a left turn signal activated signal from control panel H090 - pin 1 connector C - at pin 12.Control panel H090 receives a left turn signal activation earth signal directly from stalk unit H005 - pin 6 connector C -.