Fiat GRANDE PUNTO 1.2 8v – HEADLAMP AGLINMENT CORRECTOR – – WIRING DIAGRAM, LOCATION COMPONENTS, OPERATIONAL DESCRIPTION – WIRING DIAGRAM, LOCATION COMPONENTS, OPERATIONAL DESCRIPTION

WIRING DIAGRAM - HEADLAMP AGLINMENT CORRECTOR - Fiat GRANDE PUNTO 1.2 8v

HEADLIGHT ALIGNMENT ADJUSTMENT - WIRING DIAGRAM Fiat GRANDE PUNTO 1.2 8v

COMPONENTS - HEADLAMP AGLINMENT CORRECTOR - Fiat GRANDE PUNTO 1.2 8v

Component code	Description	Reference to the operation
B001	JUNCTION UNIT
B099	MAXI FUSE BOX ON BATTERY
C010	LEFT FRONT EARTH	-
C015	DASHBOARD EARTH, DRIVER'S SIDE	-
D020	DASHBOARD/REAR COUPLING	-
D106	REAR/CROSSMEMBER COUPLING	-
E050	INSTRUMENT PANEL
F010	LEFT HEADLAMP
F011	RIGHT HEADLAMP
H001	IGNITION SWITCH
H091	LEFT CONTROL UNIT (PCS, LEFT CONTROL PANEL)
M001	BODY COMPUTER

COMPONENT LOCATION - HEADLAMP AGLINMENT CORRECTOR - Fiat GRANDE PUNTO 1.2 8v

HEADLIGHT ALIGNMENT ADJUSTMENT - COMPONENT LOCATION Fiat GRANDE PUNTO 1.2 8v

모든 배선 다이어그램에 액세스하십시오.

Component code	Description	Reference to the operation
B001	JUNCTION UNIT
B099	MAXI FUSE BOX ON BATTERY
C010	LEFT FRONT EARTH	-
C015	DASHBOARD EARTH, DRIVER'S SIDE	-
D020	DASHBOARD/REAR COUPLING	-
D106	REAR/CROSSMEMBER COUPLING	-
E050	INSTRUMENT PANEL
F010	LEFT HEADLAMP
F011	RIGHT HEADLAMP
H001	IGNITION SWITCH
H091	LEFT CONTROL UNIT (PCS, LEFT CONTROL PANEL)
M001	BODY COMPUTER

DESCRIPTION - HEADLAMP AGLINMENT CORRECTOR - Fiat GRANDE PUNTO 1.2 8v

The adjustment of the headlamp light beam according to the load is carried out by means of a special device (located inside the front light cluster) which tilts it appropriately, lowering the light beam if the vehicle is heavily laden and raising it if the load lessens.Two buttons, located in the controls to the left of the steering wheel, allow the adjustment of the headlamps in 4 vertical positions from 0 to 3:- position 0: one or two persons in the front seats, full fuel tank, fully equipped (vehicle in running order);- position 1: five persons;- position 2: five persons with full luggage compartment (about 50 kg);- position 3: driver and 300 kg load, all stowed in the luggage compartment (full load);The device is enabled only with the dipped beams on.The relay which controls the engagement of the dipped headlamps also supplies the adjustment motors inside the headlamps; this relay for switching the dipped headlamps on is managed by the Body Computer: worelay energizing is activated by enablement signals with key in the ON position and by the steering column switch unit dipped headlamps control.

FUNCTIONAL DESCRIPTION - HEADLAMP AGLINMENT CORRECTOR - Fiat GRANDE PUNTO 1.2 8v

The dipped headlamps activation signal is sent to pin 38 of connector D of the Body Computer M1 from the steering column switch unit H5Body Computer M1 - connector G - is supplied directly from the battery via a line protected by maxifuse F2 of engine compartment control unit B1; its ignition-controlled supply (INT) is received at pin 2 of connector D; pin 10 of connector H or M1 supplies the Body Computer with a reference earth.The Body Computer M1 controls the supply for the dipped headlamps sending an earth signal to relay T3 in the junction unit in the engine compartment B1 from pin 16 of connector A of M1 which energizes relay T3: this supplies the dipped headlamps and headlamp adjusment motors F10 (left) and F11 (right). Each circuit is protected by a fuse in the junction unit B1 : F14 for the left headlamp and F15 for the right.The control for the headlamp ajustment, located in the controls to the left of the steering wheel H91.Pin 1 of H91 receives a reference earth from pin 42 of connector D of M1.A control signal generated by the two keys + and - toward instrument panel E50 - pin 14 - leaves pin 3 of H91. Pin 8 of E50 receives an enablement signal (low beams on) while the control operating the adjustment motors built into the headlamps - pin 7 of headlamps F10 (left) and F11 (right) leaves pin 7 of E50.