Functional description The ignition-operated power supply (INT) of the instrument panel E50 reaches pin 3 of connector A through the line of fuse F37 of the unit under the dashboard B2; the direct supply reaches pin 2 of connector A through the line for fuse F53 of the junction unit under the dashboard B2; pin 1 of connector A is earthed (earth controlled by the Body Computer M1 pin 36 of connector G). The instrument panel E50 is connected from pins 5 and 6 of connector A to the Body Computer M1 and via the latter to the whole CAN network: via CAN the signal for the electronic speedometer arrives (coming from the ABS control unit M50): this signal is replicated from pin 23 of M50 to pin 7 of connector A of the Body Computer M1. The electronic rev counter receives the rpm signal coming via CAN from the engine management control unit M10 . The fuel gauge is controlled in accordance with the signals coming from the fuel gauge sender unit located in the fuel pump assembly N40 - at pins 4 (positive) and 15 (negative) of connector D of the Body Computer M1, and from here via CAN to the instrument panel E50. The low brake fluid/handbrake applied warning light comes on through an earth signal from the handbrake switch I40, which reaches pin 24 of connector E of the Body Computer M1, or from the earth signal from the low brake fluid level sensor K25, which reaches pin 18 of connector A of M1. The brake pad wear warning light is controlled by an earth signal sent to pin 23 of connector B of body computer M1 from the approriate sensor K20. All these signals are transferred via CAN to the instrument panel E50 . The 'MODE' '+' and '-' controls for unit H91, send analogue signals to the instrument panel E50, to pins 13 and 16 of connector B. The TRIP function is shown in the relevant diagram 2399316SeeE4080TRIP COMPUTER . Instrument panel E50 also contains electronic modules that control panel dimmed lighting and other controls SeeE2530 INSTRUMENT LIGHTING , headlamp alignment adjustment SeeE3080 HEADLAMP AGLINMENT CORRECTOR and the parking sensors buzzer SeeE3090 PARKING SENSOR .
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b).2050746
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212400802-7040A37fuse box cover - r r1. Disconnect the electrical connections (1a, 1b, 1c, 1d, 1e, 1f).2. Undo the bracket retaining bolt.3. Slightly move the bracket (3a) for the dashboard trim and undothe bolt (3b).4. Undo the other bolts securing the body computer/junction unit.5. Slightly move the body computer/junction unit assembly.6. Disconnect the electrical connections (6a, 6b, 6c).7. Recover the body computer/junction unit.2050752
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect electronic control unit electrical connections (1a),(1b), (1c).2. Undo the bolts.3. Recover the control unit.2050753
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect electronic control unit electrical connections (1a),(1b), (1c).2. Undo the bolts.3. Recover the control unit.2050754
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Undo the bolts.2. Remove the trim (2a) releasing the retainers (2b).2051090
7040A26
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Undo the bolts.2. Remove the bottom trim (2a). To facilitate trim removal, movethe steering column after releasing the steering column positionadjustment lever (2b). 3. Undo the bolts.4. Remove the top trim.2051091
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Undo the cover bolts.2. Remove the cover (2a) by undoing the retainers (2b).2051094
7040A44
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Remove the trim (1a) releasing the inner retainers (1b) usingthe special tool.2051095
7040A45
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Remove the trim (1a) releasing the inner retainers (1b) usingthe special tool.2051096
7040A56
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212400802-7040A37fuse box cover - r r1. Undo the bolt.2. Move the trim (2a) by undoing the internal retainers (2b).3. Disconnect the electrical connections of the switch unit.4. Recover the panel with the switches.2051097
7040A65
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Undo the bolt.2. Remove closure (2a) by undoing internal retainers (2b).2051099
7040A78
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Extract compartment (1a) slightly after undoing retainers (1b).2. Disconnect the radio electrical connection.3. Disconnect the aerial lead connection.4. Recover the compartment2051100
7040A96
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Open the flap.2. Undo the bolts.3. Remove the door.2051101
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the tailgate.1. Undo the bolts.2. Move the third brake light mounting.2050831
5550D17
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the tailgate.1. Undo the bolts.2. Move the third brake light mounting.2050834
5550D18
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212400395-3380A44handbrake/linkage protection- r+r1. Move the switch after releasing the retainer.2. Disconnect the electrical connection.3. Recover the switch.2050836
5550D22
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). 1. Disconnect the electrical connection from the reversing lightsswitch.2. Undo and remove the reversing lights switch.2050837
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on therampEnsure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). Proceed with removal 2400444-4450B12front or rear wheels (two)- r+r Proceed with removal 2400333-3310A32FRONT BRAKE CALIPERS- R.R.1. Undo the bolts (1a) and remove the front brake caliper brackets(1b).2050423
3310A30
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on therampEnsure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). FOR THE LEFT BRAKE CALIPER, proceed with theremoval 2400440-4450B02left front wheel r r . FOR THE RIGHT BRAKE CALIPER, proceed with theremoval 2400441-4450B04right front wheel r r . Remove the protective cap on the brakecaliper bleed valve. Connect the collection system (pipe andreservoir) to the bleed valve on the brake caliper. Loosen the bleed valve on the brake caliperand wait for the brake-clutch reservoir and lines to drain.1. Disconnect the electrical connection for the brake pad wearsensor.2. Remove the retaining spring.3. Use tool (3a) to undo the connector (3b) and disconnect the hoseto front brake caliper (3b), rigid pipe side.4. Release the block of the hose to the front brake caliper fromthe fastener on the front shock absorber. 5. Remove plugs (5a), undo the bolts (5b) and remove the front brakecaliper assembly (5c).2050427
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on theramp FOR THE LEFT BRAKE DISC, proceed with the removal 2400440-4450B02left front wheel r r . FOR THE RIGHTT BRAKE DISC, proceed withthe removal 2400441-4450B04right front wheel r r . 1. Release the block of the hose to the front brake caliper fromthe fastener on the front shock absorber. 2. Remove plugs (2a), undo the bolts (2b) and move the front brakecaliper assembly (3c) to one side. 2050431
3310A50
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Proceed with removing bothfront brake discs 2400334-3310A48front brake disc - r r .
3310A54
If necessary, grindthe front brake discs, keeping to the figures given below.23
3310A57
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on theramp FOR THE LEFT BRAKE DISC, proceed with the removal 2400440-4450B02left front wheel r r . FOR THE RIGHT BRAKE DISC, proceed withthe removal 2400441-4450B04right front wheel r r . 1. Release the block of the hose to the front brake caliper fromthe fastener on the front shock absorber. 2. Remove plugs (2a), undo the bolts (2b) and move the front brakecaliper assembly (3c) to one side. 2050437
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on therampEnsure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). Proceed with removal 2400444-4450B12front or rear wheels (two)- r+r1. Disconnect the electrical connection for the brake pad wearsensor.2. Release the block of the hose to the front brake caliper fromthe fastener on the front shock absorber. 3. Remove plugs (3a), undo the bolts (3b) and move the front brakecaliper assembly (3c) aside. 4. Remove the front brake pads from the brake caliper. Repeat the above operations for the remainingbrake caliper.2050442
brake pump, reservoir and load proportioning valve
3330C30
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on theramp Proceed with removal 2400577-5530B10battery - r+r Proceed with removal 2400580-5530B52Battery DRIP TRAY/SUPPORT- R.R.1. Remove the protective cap on the brake caliper bleed valve. 2. Connect the collection system (pipe and reservoir) to the bleedvalve on the brake caliper. 3. Loosen the bleed valve on the brake caliperWait for the brake-clutch reservoir todrain.2050457
3330C40
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Undo the remove the brake fluid reservoir cap.2050459
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Proceed with removal 2400577-5530B10battery - r+r1. Remove the protective cap on the brake caliper bleed valve. 2. Connect the collection system (pipe and reservoir) to the bleedvalve on the brake caliper. 3. Loosen the bleed valve on the brake caliperWait for the brake-clutch reservoir todrain.2050481
3340A13
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Proceed with removal 2400577-5530B10battery - r+r Proceed with removal 2400367-3340A12A'B.S. system. - electronicand hydraulic CONTROL UNIT R.R.1. Release the right brake pipe from the band on the A.B.S. controlunit mounting.2. Undo the nuts (2a) and the bolt (2b) and remove the A.B.S. controlunit mounting (2c).2050485
3340A20
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting2123-. For versions with ESP, theA.B.S. electronic control unit is handled individually by the Parts Department,but supplied together with the hydraulic control unit. Proceed with removal 2400577-5530B10battery - r+r Proceed with removal 2400367-3340A12A'B.S. system. - electronicand hydraulic CONTROL UNIT R.R.1. Undo the bolts (1a) and separate ABS electronic control unt (1b)from the hydraulic assembly.2050486
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21.23The following procedure describesremoval/refitting of the left rear wheel rpm sensor; proceed asfor the right rear wheel rpm sensor.Position the vehicle on the rampEnsure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). 1. Undo the bolt (1a) and remove the rear wheel rpm sensor (1b).2. Release the rear wheel rpm sensor electrical wiring from theattachments on the rear suspension.2050491
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on the rampEnsure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). Proceed with removal 2400114-1040A70submerged pump assemblycomplete with level guage control - r + rDrain the fuel from the tank using suitableequipment and appropriate protection to meet current safety requirements.1. Release the protection and move it aside.2. Slacken the handbrake cable adjustment nut.2049677
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on the ramp Proceed with removal 2400443-4450B08right rear wheel r r Proceed with removal 2400916-7055B45right hand rear supplementarywheel arch - r+r1. Undo the bolt securing the fuel filler pipe to the body.2. Loosen the band (2a) and disconnect the fuel filler pipe (2b)from the tank.3. Loosen the band (3a) and disconnect return pipe (3b).4. Remove the sleeve joining the fuel filler pipe to the tank.2049687
1040A40
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Open the access flap to the fuel filler pipe cap.2. Release the safety device for the fuel filler pipe cap from thebodyshell.3. Undo and remove the fuel filler pipe cap.2049688
1040A70
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). 1. Lift the rear seat cushion lift the floor covering to gain accessto the fuel pump flap.2. Unscrew retaining bolts (2a) and remove protective cover (2b).3. Disconnect the electrical connection from the immersed pump assemblycomplete with gauge.Undo the fuel filler cap and remove itto discharge the pressure in the system.4. Disconnect the rapid attachment for the fuel supply pipe fromthe immersed pump assembly.2049691
1040A74
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). 1. Move the upper section of the floor covering near the passengerside dashboard aside.2. Disconnect the electrical connection from the inertia switch.3. Undo retaining nuts (3a) and remove inertia switch (3b)2049694
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Čeština
Dansk
Deutsch
Ελληνικά
English
English
Español
Suomi
Français
Français
עברית
Hrvatski
Magyar
Italiano
日本語
Nederlands
Polski
Português
Português
Română
Русский
Slovenčina
Slovenščina
Svenska
Türkçe
中文 (中国)
