Fiat ULYSSE 2.2 16V JTD fino a 04/03 – DIPPED HEADLAMPS – – MY 2005 – WIRING DIAGRAM, LOCATION COMPONENTS, OPERATIONAL DESCRIPTION – WIRING DIAGRAM, LOCATION COMPONENTS, OPERATIONAL DESCRIPTION

DIPPED HEADLIGHTS WIRING DIAGRAM Fiat ULYSSE 2.2 16V JTD fino a 04/03

Components - DIPPED HEADLAMPS - Fiat ULYSSE 2.2 16V JTD fino a 04/03

Component code	Description	Reference to the assembly
A001	BATTERY	-
B001	ENGINE COMPARTMENT JUNCTION UNIT	5,505A
C010	LEFT FRONT EARTH	-
C011	RIGHT FRONT EARTH	-
C015	DRIVER''S DASHBOARD EARTH	-
C020	PASSENGER SIDE DASHBOARD EARTH	-
D006	FRONT/REAR COUPLING	-
D020	DASHBOARD/REAR COUPLING	-
E050	INSTRUMENT PANEL
F010	LEFT HEADLAMP
F011	RIGHT HEADLAMP
H001	Ignition switch
K125	RAIN AND DUSK SENSOR
M001	BODY COMPUTER
M093	STEERING WHEEL NODE CONTROL UNIT (NVO)
M140	WARNING LIGHTS AND MILOMETER CONTROL UNIT (NSO)	-

DIPPED HEADLIGHTS COMPONENT LOCATION Fiat ULYSSE 2.2 16V JTD fino a 04/03

모든 배선 다이어그램에 액세스하십시오.

Component code	Description	Reference to the assembly
A001	BATTERY	-
B001	ENGINE COMPARTMENT JUNCTION UNIT	5,505A
C010	LEFT FRONT EARTH	-
C011	RIGHT FRONT EARTH	-
C015	DRIVER''S DASHBOARD EARTH	-
C020	PASSENGER SIDE DASHBOARD EARTH	-
D006	FRONT/REAR COUPLING	-
D020	DASHBOARD/REAR COUPLING	-
E050	INSTRUMENT PANEL
F010	LEFT HEADLAMP
F011	RIGHT HEADLAMP
H001	Ignition switch
K125	RAIN AND DUSK SENSOR
M001	BODY COMPUTER
M093	STEERING WHEEL NODE CONTROL UNIT (NVO)
M140	WARNING LIGHTS AND MILOMETER CONTROL UNIT (NSO)	-

The vehicle is equipped with two dipped beams in the headlamps.The dipped beams are activated by turning a wheel on the stalk switch to the next position after the side light setting.A special relay in the engine compartment junction unit controls activation of the low beams via two lines protected by specific fuses.The low beam activation relay is managed by the body computer: relay excitation is activated by enablement signals with key in position M and a specific stalk switch command.Activation/deactivation information is sent via the CAN network: in this way, the main beam warning light is activated in the instrument panel.The body computer also manages the low beam maintenance function: when the high beams are turned on, the body comuter keeps the low beams on.If the dipped beams and the main beams are already on and the fog lights are turned on, then the dipped beams are switched off.Similarly, if the dipped beams and the fog lights are on and the main beams are switched on, the dipped beams are switched off.In other words, when the main beams and the fog lights are on, the dipped beams are always off.The dipped beams can also be activated automatically, using the AUTO button on the steering column switch unit: this function is achieved by means of an infrared dusk sensor located in the windscreen.Activation and deactivation is accompanied by an auditory warning signal.769When the device is switched on, the lights come on automatically even if the windscreen wiper is operated.The "Follow me home" function allows the dipped headlamps and the side lights to remain on even after the engine has been switched off (key in position S) for a period of 45 seconds.The side lights warning light in the instrument panel signals that the lights have remained on. The lights are activated by operating the light flasher stalk within 2 minutes of switching the engine off.

The low beam activation command is supplied by steering wheel node control unit M093 via CAN line (pins 1 and 3 of connector A) to body computer node M001 (at pins 5 and 3 of connector G respectively).Steering wheel node control unit M093 is connected to earth C015 (connector A) via pin 4 of connector A, and is supplied by two lines: one, from pin 11 of connector B of body computer node M001 to pin 5 of connector A; the other, from pin 1 of connector G of M001 to pin 4 of connector D, protected by fuse F04.In turn, body computer node M001 informs engine junction unit B001 (pins 12 and 11 respectively of connector F) via the CAN line (pins 25 and 27 of connector E) that a low beam activation request has been made.Engine compartment junction unit B001 suppplies pin 1 of left headlamp F010 and right headlamp F011 via pins 25 and 26 of connector G.Warning light activation is controlled by odometer warning light node M140, which communicates via CAN line E1050 (pins 2 and 5) with instrument panel E050 (pins 6 and 12) and body computer node M001 (pins 8 and 10 connector D).Body computer node M001 supplies odometer warning light node M140 at pin 4 and instrument panel E050 at pin 13 via pin 6 of connector D. This line is protected by fuse F14.Dawn-dusk sensor K125 supplies information on the exterior light conditions to body computer node M001, at pins 3, 24, 26 (respectively) of connector L via pins 1, 2, 4.