DescriptionThe car is equipped with numerous self-diagnostic electronic control units. When a tester (Examiner or other instrument) is connected to the control units, self-diagnostic data can be read (parameters, errors) or active testing can be carried out.This car is not fitted with a specific tester connection for each control unit. Instead, a single standard 16-way tester connection is located on the left hand side of the facia, above the junction unit.The tester (Examiner or other instruments) is connected to this (via an adaptor) and the software is then used to select the required self-diagnostic function.
Functional description Tester connection R10 is supplied directly by the battery (maxifuse CENTR of B5 ) via fuse F17 of junction unit B1 . Pins 4 and 5 are earthed. The pins are connected to the ABS control unit M50 - pin 11 - ( 3309988SeeE7020ABS ). Pin 3 is connected to airbag control unit M60 - pin 9 - ( 3310036SeeE7030AIRBAG ). Pin 11 is connected to alarm control unit M30 - pin 6 of connector A - and remote control receiver M35 - pin 2 - ( 3309960SeeE7015ALARM ). Pin 8 is connected to Code control unit M20 - pin 5 - ( 3309948SeeE7010CODE ). Pin 7 is connected to engine management control unit M10 via a dedicated line.
0Removing201Refitting213314824-5505A18multi-function controlunit - r r . 1. Undo the bolt (1a) and push back the junction unit as far asnecessary to disconnect the electrical connections (1b).767For precise identification ofthe electrical connections, see Wiring Diagrams Section.2. Remove the junction unit.2010592
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Unscrew bolt (1a) and open fuse access cover (1b).2. Undo the bolt (2a) and remove the integrated multiservices unit(2b) after having disconnected the electrical connections (2c),(2d), (2e), (2f) and (2g).2010595
5505A29
0Removing201Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b) for theadditional junction unit.2071293
0Removing201Refitting213314864-5530B54battery cover - r+r . Make sure that the ignition key is in theOFF position.1. Disconnect the battery negative and positive terminals.2. Undo the bolt (2a) fixing the battery retaining bracket (2b).3. Remove the battery.2010647
5530B40
0Removing201Refitting213314864-5530B54battery cover - r+r1. Press and release the retainers (1a), then remove the cover (1b)for the supply box on the battery. 2071303
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). Lower the steering wheel and move it back.1. Undo the bolts (1a) and remove the upper half casing for thesteering column (1b).2010703
5560B12
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). Open the fuse carrier compartment flap.1. Using the tool (1a) and pushing the fuse carrier compartment,remove the surround (1b) complete with switches.2. Disconnect the elelectrical connections (2a), (2b) and (2c) andremove the surround complete with switches.2010706
0Removing201Refitting21Undo the wing bolts and removethe boot left side trim. Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). Disconnect the electrical connections forthe loudspeakers' amplifier.1. Undo the nuts and move aside the on-board navigator componentsmounting as far as necessary.Disconnect the electrical connection fromthe navigation system CD player/changer.Disconnect the electrical connections ofthe audio CD player/changer.2. Remove the complete on-board navigator components mounting.2010738
0Removing201Refitting21 Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 3314048-1016A40ignition coil cover on cylinder head- r+r . 3314111-1048A48throttle heater sleeve - r r . 1. Disconnect the electrical connection from the butterfly casingintegrated with the M.D.S.2. Disconnect the electrical connections (2a) and (2b) from theinjection/ignition control unit and the earth lead (2c) from thebutterfly casing integrated with the M.D.S.3. Disconnect the accelerator cable from the butterfly casing integratedwith the M.D.S.4. Disconnect the injection/ignition wiring from the mounting bracket.5. Undo the bolts (5a) and remove the butterfly casing integratedwith the M.D.S. (5b) complete with the injection/ignition controlunit (5c).2007326
1056B21
0Removing201Refitting21 Ensure that the ignition key is in OFFposition, then disconnect the battery negative terminal ( 3314861-5530B10battery - r+r ). Proceed with the removal 3315197-7040D14engine bay rear sidecover (one) lh or rh - r r (Right side). 1. Loosen the band (1a) and disconnect the oil vapour recirculationpipe (1b) from the corrugated hose.2. Loosen the bands (2a) and remove the hose between resonator andthrottle body (2b), complete with resonator (2c).2007327
1056B48
0Removing201Refitting21 Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 3314048-1016A40ignition coil cover on cylinder head- r+r . 1. Disconnect the electrical connection from the phase transformerelectro-magnet.2. Undo the bolts (2a) and remove the phase transformer electro-magnet(2b).2007334
1056B50
0Removing201Refitting21 Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 3314110-1048A28vacuum air circuit resonator pipe - r+r1. Disconnect the electrical connection from the engine coolanttemperature sensor.2. Undo and remove the engine coolant temperature sensor.2007335
0Removing201Refitting21 Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 3314048-1016A40ignition coil cover on cylinder head- r+r . Discharge the fuel supply pressure (seeGroup 10 Warnings).1. Disconnect the rapid attachment for the fuel supply pipe.2. Disconnect the electrical connections from the injectors (2a)and the electrical connection from the phase transformer electro-magnet(2b).3. Undo the two bolts (3a) and remove the single fuel manifold pipe(3b) complete with injectors (3c).2007337
1056B68
0Removing201Refitting211. Remove the clips (1a) and remove the injectors (1b) from thesingle fuel manifold pipe.2. Remove the seals from the injectors.2007338
Make sure that the ignition key is in theOFF position. Check that: the air conditioning is switchedoff, the accelerator pedal is never pressed and the accelerator cableis correctly positioned (refer to op. 33141321068A30accelerator control cable - r + r ). Connect the tool to the diagnostic socketand place the knob in position 3.Connect the Examiner diagnostic equipment.Connect the Examiner diagnostic equipment.Using the Examiner, enter the "ControlUnit Test" ambient.Place the ignition key in the ON position.Using the Examiner, enter the "ActiveDiagnosis" ambient, then select "Reset self-adjustmentparameters" and "Idle actuator".Using the Examiner, press "Carry outactive diagnosis".Place the ignition key in the OFF positionand wait for 30 seconds.Place the ignition key in the ON positionand wait for 30 seconds.Using the Examiner, re-establish the dialoguewith the engine control system.Using the Examiner, enter the "Parameters"ambient and select the following tests from the menu - "Idle recognitiontest - carried out" and "Idle recognition signals - synchronized".767If at least one of the parametersdoes not conform, place the ignition key in the OFF position andrepeat the procedure. If this non conformity persists, check thatthe diagnostic cable is correctly connected and check the operationof the instrument.Place the ignition key in the OFF positionand wait for 30 seconds.Start up the engine without acting on theaccelerator pedal.Disconnect the diagnostic equipment.Test the vehicle by driving for severalkilometres then, with the engine warmed up, check that it is idlingcorrectly.
1056B82
0Removing201Refitting21 Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 1. Release and disconnect the electrical connections (1a) and (1b)from the injection/ignition system control unit.2. Undo the nuts (2a) and remove the injection/ignition controlunit (2b).2007339
1056B82
0Removing201Refitting21 Ensure that the ignition key is in OFFposition, then disconnect the battery negative terminal ( 3314861-5530B10battery - r+r ). Proceed with the removal 3315197-7040D14engine bay rear sidecover (one) lh or rh - r r (Right side). 1. Loosen the band (1a) and disconnect the oil vapour recirculationpipe (1b) from the corrugated hose.2. Loosen the bands (2a) and remove the hose between resonator andthrottle body (2b), complete with resonator (2c).2007340
0Removing201Refitting21 Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 1. Disconnect the electrical connection from the intake air temperaturesensor.2. Undo and remove the intake air temperature sensor.2007791
1056B62
0Removing201Refitting21 Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). Discharge the fuel pressure (see GR 10- WARNINGS).1. Disconnect the electrical connections from the injectors.2007793
0Removing201Refitting21 Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 1. Disconnect the electrical connection from the altitude corrector. 2. Undo the attachments and remove the altitude corrector.2007796
1056B79
0Removing201Refitting211. Remove the buttons (1a) using the tool (1b) and remove the protection(1c).2. Open the two protective covers (2a) and undo the nuts (2b) underneathfixing the control unit cover.3. Undo the bolts (3a) and remove the control unit cover (3b).2007797
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Unscrew bolt (1a) and open fuse access cover (1b).2. Undo the nuts (2a) and remove the electronic key anti-theft controlunit (2b) after having disconnected the electrical connections (2c)and (2d).2010733
0Removing201Refitting21Ensure that the ignition keyis in stop position, then disconnect the battery negative terminal3314911-5550D16third stop light - r+r . 1. Undo the bolts fixing the anti-theft remote control receiverto the rear parcel shelf.2. Remove the anti-theft device remote control receiver (2a) afterhaving disconnected the electrical connection (2b).2010735
5580E46
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3315190-7040B13load compartment/load platform right side trim -r r . 1. Undo the bolt (1a) and the nut (1b) fixing the anti-theft devicealarm/control unit.2. Disconnect the electrical connections (2a) and (2b), then removethe anti-theft device alarm/control unit (2c).2010736
5580E50
0Removing201Refitting211. Press in the direction of the arrow and lower the volumetricsensor unit (1a), releasing it from the inner retainers (1b) and(1c). 2071341
0Removing201Refitting21Position the vehicle on theramp. Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 3315196-7040D12engine front side cover (one) lh or rh - r r (left). 3315197-7040D14engine bay rear side cover (one) lh or rh - r r (left). Remove the cap with built-in brake fluidlevel switch and drain the brake/clutch fluid from the reservoir usinga suitable syringe.1. Disconnect the comb from the A.B.S. hydraulic and electroniccontrol unit.2. Release the A.B.S. pipes from their clip.3. Disconnect the pipes from the A.B.S. hydraulic and electroniccontrol unit and move them aside.2009904
0Removing201Refitting21 Make sure that the ignition is in the OFFposition, then disconnect the negative battery terminal (refer toop. 33148615530B10battery - r+r ). 1. Undo the bolts (1a) and remove the right and left trims (1b).2009600
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3315182-7040A45facia rh side cover - r r . 1. Remove the switch for deactivating the passenger Air Bag (1a)using the tool (1b) after having disconnected the electrical connection(1c).2010723
0Removing201Refitting21- 7045A10 l/h or r/h front seat (one) - r+r - 7045A98 front seat rear pouch panel, lh or rh - r r 3315250-7045B10l/h or r/h front seat head restraint - r+r- 7045A84 Front set BACKREST COVER - R.R. with seat removed - 7045A88 Front seat BACKREST UPHOLSTERY, left or right - R.R.with seat removed 7691. Disconnect the electrical connection for the sidebag. Take careto remove without damaging it. 2. Undo bolt (2a) and disconnect the sidebag earth cable (2b) 3. Cut the collars securing the wiring to the chassis.4. Release the sidebag module and wiring from the protective casing.5. Remove the wiring by withdrawing from its seat.2010731
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.