Wiring Diagram VW TOURAN 2008 - Airbag control unit - terminal 15 voltage supply relay 2 - steering column electronics control unit - driver side airbag igniter
![VW TOURAN 2008 – Airbag systems (with front passenger airbag deactivation) . Wiring diagrams, Pin Connector, Location Download PDF file](/images/pdf-80.jpg)
A | Battery |
B | Starter |
C | Alternator |
F138 | Airbag coil connector |
J234 | Airbag control unit, behind the lower console |
J519 | Onboard supply control unit |
J527 | Steering column electronics control unit |
J681 | Terminal 15 voltage supply relay 2, onboard supply control unit (460) |
J682 | Terminal 50 voltage supply relay |
N95 | Driver side airbag igniter |
SA1 | Fuse 1 on fuse holder A |
SB28 | Fuse 28 on fuse holder B |
SC6 | Fuse 6 on fuse holder C |
T4ak | 4-pin connector |
T10x | 10-pin connector |
T12k | 12-pin connector |
T40 | 40-pin connector |
T75 | 75-pin connector |
508 | Screw connection (30), on electronics box |
A200 | Positive connection 5 (15a), in dash panel wiring harness |
B163 | Positive connection 1 (15), in interior wiring harness |
D50 | Positive connection (30), in engine compartment wiring harness |
* | Models with 90 A/ 120 A alternator |
** | Models with 140 A alternator |
Wiring Diagram VW TOURAN 2008 - Airbag control unit - side airbag crash sensors - front passenger side airbag igniter - front passenger side airbag deactivated warning lamp
G179 | Side airbag crash sensor on driver side |
G180 | Side airbag crash sensor on front passenger side |
J234 | Airbag control unit, behind the lower console |
J519 | Onboard supply control unit |
K145 | Front passenger side airbag deactivated warning lamp |
N131 | Front passenger side airbag igniter 1 |
T3j | 3-pin connector, near front passenger airbag |
T4al | 4-pin connector |
T75 | 75-pin connector |
109 | Earth connection, in airbag wiring harness |
312 | Earth connection 2, in airbag wiring harness |
T3 | Connection, in airbag wiring harness |
*** | only models with side airbag |
Wiring Diagram VW TOURAN 2008 - Airbag control unit - side airbag igniter - key operated switch to deactivate front passenger side airbag
E224 | Key operated switch to deactivate front passenger side airbag |
J234 | Airbag control unit, behind the lower console |
J519 | Onboard supply control unit |
N199 | Side airbag igniter on driver side |
N200 | Side airbag igniter on front passenger side |
T3ad | 3-pin connector, in driver seat backrest |
T3ae | 3-pin connector, in front passenger seat backrest |
T3k | 3-pin connector, under driver seat |
T3l | 3-pin connector, under front passenger seat |
T8g | 8-pin connector |
T75 | 75-pin connector |
T5 | Connection 2, in airbag wiring harness |
*** | only models with side airbag |
Wiring Diagram VW TOURAN 2008 - Airbag control unit - rear side airbag crash sensors - belt tensioner igniter - curtain airbag igniter
G256 | Rear side airbag crash sensor on driver side |
G257 | Rear side airbag crash sensor on front passenger side |
J234 | Airbag control unit, behind the lower console |
J519 | Onboard supply control unit |
N153 | Driver seat belt tensioner igniter |
N154 | Front passenger seat belt tensioner igniter |
N251 | Driver side curtain airbag igniter |
N252 | Front passenger side curtain airbag igniter |
T3m | 3-pin connector, behind D-pillar trim on lower left |
T3n | 3-pin connector, behind D-pillar trim on lower right |
T3o | 3-pin connector, behind B-pillar trim on lower left |
T3p | 3-pin connector, behind B-pillar trim on lower right |
T75 | 75-pin connector |
** | models with curtain airbag only |
*** | only models with side airbag |
Wiring Diagram VW TOURAN 2008 - Airbag control unit - driver side belt switch - front passenger side belt switch - seat occupied sensor - front passenger side
E24 | Driver side belt switch |
E25 | Front passenger side belt switch |
G128 | Seat occupied sensor, front passenger side |
J234 | Airbag control unit, behind the lower console |
J519 | Onboard supply control unit |
T2o | 2-pin connector, under front passenger seat |
T2q | 2-pin connector, under driver seat |
T75 | 75-pin connector |
109 | Earth connection, in airbag wiring harness |
B383 | Connection 1 (drive train CAN bus, high), in main wiring harness |
B390 | Connection 1 (drive train CAN bus, low), in main wiring harness |
** | models without front passenger seat contact switch only |
--- | models with front passenger seat contact switch only |
Wiring Diagram VW TOURAN 2008 - Dash panel insert - data bus diagnostic interface - self-diagnosis connection - airbag warning lamp - seat belt warning system warning lamp
J285 | Control unit with display in dash panel insert |
J519 | Onboard supply control unit |
J533 | Data bus diagnostic interface, on left under dash panel |
K19 | Seat belt warning system warning lamp |
K75 | Airbag warning lamp |
T16 | 16-pin connector, under dash panel left behind storage compartment, self-diagnosis connection |
T20 | 20-pin connector |
T36 | 36-pin connector |
A204 | Connection (dash panel insert CAN bus, high), in dash panel wiring harness |
A205 | Connection (dash panel insert CAN bus, low), in dash panel wiring harness |
B383 | Connection 1 (drive train CAN bus, high), in main wiring harness |
B390 | Connection 1 (drive train CAN bus, low), in main wiring harness |
B397 | Connection 1 (convenience CAN bus, high), in main wiring harness |
B406 | Connection 1 (convenience CAN bus, low), in main wiring harness |
VW TOURAN 2008 Overview of control units
1 - | ABS control unit -J104- |
q | 26-pin connector assignment |
q | 47-pin connector assignment |
2 - | Engine control unit -J623- |
q | 121-pin connector assignment |
q | 154-pin connector assignment |
3 - | Aerial selection control unit -J515- |
4 - | Vehicle inclination sender -G384- |
5 - | Convenience system central control unit -J393- |
q | Connector assignment |
6 - | Traffic information control unit -J559- /Chip card reader control unit -J676- |
q | Fitting location |
7 - | Climatronic control unit -J255- |
7 - | Air conditioning system control unit -J301- |
8 - | Control unit in dash panel insert -J285- |
q | Connector assignment 32-pin connector -T32- |
8 - | Traffic data aerial -R173- |
9 - | Steering column electronics control unit -J527- |
q | Fitting location from May 2010 |
q | Connector assignment to May 2010 |
q | Connector assignment from May 2010 |
q | Connector assignment |
11 - | Park assist steering control unit -J791- / Parking aid control unit -J446- |
q | Fitting location |
q | Connector assignment |
12 - | Onboard supply control unit -J519- |
q | Connector assignment to May 2010 |
q | Fitting location from May 2010 |
q | Connector assignment from May 2010 52-pin connector -T52 A--black- |
q | Connector assignment from May 2010 52-pin connector -T52 B--white- |
q | Connector assignment from May 2010 52-pin connector -T52 C--brown- |
q | Connector assignment |
13 - | Mechatronic unit for dual clutch gearbox -J743- |
q | 20-pin connector assignment |
Dual clutch gearbox 0AM: |
q | Fitting location |
q | 25-pin connector assignment |
14 - | Voltage stabiliser -J532- |
15 - | Headlight range control unit -J431- |
q | Connector assignment |
15 - | Control unit for cornering light and headlight range control -J745- |
q | Connector assignment |
q | Connector assignment 75-pin connector -T75- |
q | Connector assignment 50-pin connector -T50- |
17 - | Power steering control unit -J500- |
q | Connector assignment |
q | Fitting location from May 2010 |
|
26-pin connector assignment: |
A - | ABS control unit -J104- |
Connector: |
B - | 26-pin connector -T26a- on wiring harness |
Back to overview |
47-pin connector assignment: |
A - | ABS control unit -J104- |
Connector: |
B - | 47-pin connector -T47- /-T47a- on wiring harness |
Back to overview |
|
121-pin connector assignment: |
A - | Engine control unit -J623- |
Connector: |
B - | 81-pin connector -T81- on wiring harness |
C - | 40-pin connector -T40- on wiring harness |
Note
-T121- is comprised of items B and C. |
Back to overview |
154-pin connector: |
A - | Engine control unit -J623- |
Connector: |
B - | 94-pin connector -T94- on wiring harness |
C - | 60-pin connector -T60- on wiring harness |
Note
-T154- is comprised of items B and C. |
Back to overview |
|
|
Connector assignment: |
A - | Convenience system central control unit -J393- |
Connector: |
B - | 6-pin connector -T6- on wiring harness |
C - | 18-pin connector -T18- on wiring harness |
D - | 8-pin connector -T8- on wiring harness |
E - | 6-pin connector -T6- on wiring harness |
F - | 18-pin connector -T18a- on wiring harness |
Back to overview |
|
|
|
36-pin connector -T36- on wiring harness: |
1 - | Voltage supply positive, terminal 15 |
2 - | Voltage supply positive, terminal 30 |
3 - | Vacant |
4 - | Vacant |
5 - | Brake fluid level warning lamp -K33- |
6 - | Handbrake warning switch -F9- |
7 - | Immobiliser reader coil -D2- |
8 - | Immobiliser reader coil -D2- |
9 - | Speedometer -G21- Output signal on instrument cluster, not assigned in current flow diagram |
10 - | Vacant |
11 - | Vacant |
12 - | Data bus diagnostic interface -J533- Dash panel CAN, low |
13 - | Data bus diagnostic interface -J533- Dash panel CAN, high |
14 - | Vacant |
15 - | Data bus diagnostic interface -J533- Dash panel CAN wake-up wire |
16 - | Vacant |
17 - | Fuel gauge -G1- (full) |
18 - | Fuel gauge -G1- (empty) |
19 - | Earth connection 2, in main wiring harness -367- Terminal 31 |
20 - | Vacant |
21 - | Vacant |
22 - | Front left brake pad wear sender -G34- |
23 - | Vacant |
24 - | Fuel tank flap lock warning lamp |
25 - | Oil pressure switch -F1- |
26 - | Oil level and oil temperature sender -G266- |
27 - | Vacant |
28 - | Sliding sunroof adjustment control unit -J245- ,Control unit with display for radio and navigation -J503- Speedometer signal, output |
29 - | Vacant |
30 - | Vacant |
31 - | Vacant |
32 - | Vacant |
33 - | Earth connection (sender earth) in interior wiring harness -401- |
34 - | Windscreen washer fluid level sender -G33- |
35 - | Coolant shortage indicator sender -G32- |
36 - | Ambient temperature sensor -G17- |
Back to overview |
32-pin connector -T32- on wiring harness: |
1 - | Fuel gauge sender -G- (full) |
2 - | Fuel gauge sender -G- (empty) |
3 - | Vacant |
4 - | Vacant |
5 - | Vacant |
6 - | Vacant |
7 - | Immobiliser reader coil -D2- |
8 - | Immobilizer reader coil 2 -D3- |
9 - | Vacant |
10 - | Vacant |
11 - | Oil level and oil temperature sender -G266- |
12 - | Vacant |
13 - | Vacant |
14 - | Vacant |
15 - | Front left brake pad wear sender -G34- |
16 - | Earth connection 22, in main wiring harness -367- |
17 - | Washer fluid level warning lamp -K37- |
18 - | Coolant temperature and coolant shortage warning lamp -K28- |
19 - | Ambient temperature sensor -G17- |
20 - | Earth connection 1 (sender earth) in main wiring harness -410- |
21 - | Vacant |
22 - | Vacant |
23 - | Vacant |
24 - | Vacant |
25 - | Handbrake warning lamp -K139- |
26 - | Brake fluid level warning lamp -K33- |
27 - | Oil pressure warning lamp -K3- |
28 - | Data bus diagnostic interface -J533- Dash panel CAN, high |
29 - | Data bus diagnostic interface -J533- Dash panel CAN, low |
30 - | Vacant |
31 - | Voltage supply positive, terminal 15 |
32 - | Voltage supply positive, terminal 30a |
Back to overview |
|
|
Connector assignment: |
A - | Steering column electronics control unit -J527- |
B - | Airbag connector: |
1 - | Airbag 1 - |
2 - | Airbag 1+ |
3 - | Airbag 2+ |
4 - | Airbag 2 - |
C - | Connector for turn signal switch -E2- / Headlight dipper and flasher switch -E4- / Cruise control system switch -E45- : |
1 - | Cruise control system terminal 15 voltage supply |
2 - | CCS off |
3 - | Cruise control system (CCS) SET button -E227- Res (+), Set (-) |
4 - | CCS on/off |
5 - | Earth CCS |
6 - | Cruise control system terminal 58 illumination |
7 - | Headlight flasher |
8 - | Main beam |
9 - | Turn signal |
10 - | Turn signal earth |
D - | 20-pin connector -T20d- on wiring harness |
1 - | Taxi two-way radio 2 |
2 - | Taxi two-way radio 1 |
3 - | Taxi alarm 2 |
4 - | Taxi alarm 1 |
5 - | Vacant |
6 - | Vacant |
7 - | Vacant |
8 - | Vacant |
9 - | Vacant |
10 - | Powertrain CAN shielding |
11 - | Data bus diagnostic interface -J533- / Connection 1 (powertrain CAN bus, low), in main wiring harness -B390- |
12 - | Data bus diagnostic interface -J533- / Connection 1 (powertrain CAN bus, high), in main wiring harness -B383- |
13 - | Cruise control system, output |
14 - | Data bus diagnostic interface -J533- / Connection 1 (convenience CAN bus, high), in main wiring harness -B397- |
15 - | Data bus diagnostic interface -J533- / Connection 1 (convenience CAN bus, low), in main wiring harness -B406- |
16 - | Selector lever locked in position P switch -F319- |
17 - | Terminal 15 |
18 - | Terminal 50 |
19 - | Terminal 30 |
20 - | Terminal 31 |
E - | 4-pin connector -T4ak- on wiring harness |
1 - | Airbag 1 - |
2 - | Airbag 1+ |
3 - | Airbag 2+ |
4 - | Airbag 2 - |
F - | 12-pin connector -T12j- / ignition/starter switch -D- / ignition key withdrawal lock solenoid -N376- : |
1 - | Vacant |
2 - | Vacant |
3 - | 2-pin connector -T2dy- / ignition key withdrawal lock solenoid -N376- Terminal 30 |
4 - | 2-pin connector -T2dy- / ignition key withdrawal lock solenoid -N376- Earth |
5 - | Vacant |
6 - | Vacant |
7 - | Ignition/starter switch -D- Terminal 50, output |
8 - | Ignition/starter switch -D- Terminal 30 |
9 - | Ignition/starter switch -D- Terminal S, output |
10 - | Ignition/starter switch -D- Terminal X, output |
11 - | Ignition/starter switch -D- Terminal P, output |
12 - | Ignition/starter switch -D- Terminal 15, output |
G - | Connector for intermittent wiper switch -E22- / sliding sunroof adjustment regulator -E38- / washer pump switch (automatic wash/wipe and headlight washer system) -E44- / multifunction display call-up button -E86- / reset button -E92- : |
1 - | Wiper switch signal |
2 - | Earth wiper |
3 - | Rear lid wash/wipe signal |
4 - | Vacant |
5 - | MFD signal |
6 - | Earth MFD, interval potentiometer |
7 - | Intermittent operation speeds signal |
8 - | Vacant |
H - | Connector for steering angle sender -G85- : |
1 - | Photoelectric beam 5 |
2 - | Photoelectric beam 3 |
3 - | Photoelectric beam 1 |
4 - | 12 Volt voltage supply, steering angle sender |
5 - | 5 Volt voltage supply, steering angle sender |
6 - | Photoelectric beam 6 |
7 - | Photoelectric beam 4 |
8 - | Photoelectric beam 2 |
9 - | Earth |
10 - | Photoelectric beam 7 |
I - | 10-pin connector -T10x- / coil connector -F350- / airbag coil connector and return ring with slip ring -F138- : |
1 - | Vacant |
2 - | Vacant |
3 - | Airbag 1 + |
4 - | Airbag 1 - |
5 - | Airbag 2 + |
6 - | Airbag 2 - |
7 - | Earth for coil connector, multifunction steering wheel and signal horn |
8 - | CCS in detent -Off-, signal horn |
9 - | LIN bus, heated steering wheel temperature sensor |
10 - | Multifunction steering wheel voltage supply terminal 15 |
Back to overview |
Steering column electronics control unit -J527- , from May 2010 |
Fitting location: |
1 - | Steering column electronics control unit -J527- |
Near steering column switch |
Connectors: |
q | -A-16-pin connector -T16k- |
q | -B-4-pin connector -T4k- |
Back to overview |
|
1 - | Fuse 6 on fuse holder B -SB6- via B504 Positive connection 8 (30a) in interior wiring harness |
q | Only models with no start/stop system |
- Fuse 57 on fuse holder C -SC57- via B321 Positive connection 7 (30a) in main wiring harness |
q | Only models with start/stop system |
2 - | 382 Earth connection 17 in main wiring harness |
3 - | B406 Connection 1 (convenience CAN bus, low), in main wiring harness |
4 - | B397 Connection 1 (convenience CAN bus, high), in main wiring harness |
5 - | Engine control unit -J623- , GRA E_A) |
6 - | Onboard supply control unit -J519- , (T52c/14), (terminal 50) |
7 - | Terminal S, vacant |
8 - | Vacant |
9 - | Vacant |
10 - | Vacant |
11 - | Selector lever locked in position P switch -F319- , P locked |
12 - | B390 Connection 1 (powertrain CAN bus, low), in main wiring harness |
13 - | B383 Connection 1 (powertrain CAN bus, high), in main wiring harness |
14 - | Onboard supply control unit -J519- , (T52c/13, T52c/31) |
15 - | Vacant |
16 - | Vacant |
|
1 - | Airbag control unit -J234- , (T50/21), (airbag 1+) |
2 - | Airbag control unit -J234- , (T50/20), (airbag 1–) |
3 - | Vacant |
4 - | Vacant |
Back to overview |
|
|
Connector assignment: |
A - | Data bus diagnostic interface -J533- |
Connector: |
B - | 20-pin connector -T20- on wiring harness |
Back to overview |
|
A - | Park assist steering control unit -J791- / Parking aid control unit -J446- |
B - | Front parking aid warning buzzer -H22- |
Back to overview |
Connector assignment: |
A - | Parking aid control unit -J446- / park assist steering control unit -J791- |
B - | 16-pin connector -T16j- |
Connector assignment: |
1 - | Fuse 11 on fuse holder B -SB11- Terminal 15 |
2 - | Rear parking aid warning buzzer -H15- Pin 1 - |
3 - | Vacant |
4 - | Parking aid button -E266- Pin 4 |
5 - | Vacant |
6 - | Data bus diagnostic interface -J533- , Powertrain CAN bus high |
7 - | Vacant |
8 - | Earth connection |
9 - | Warning light for park assist steering -K241- Pin 2 |
10 - | Rear parking aid warning buzzer -H15- Pin 1 + |
11 - | Vacant |
12 - | Vacant |
13 - | Parking aid warning lamp -K136- Pin 2 |
14 - | Vacant |
15 - | Data bus diagnostic interface -J533- Powertrain CAN bus low |
16 - | Park assist steering button -E581- Pin 5 |
C - | 12-pin connector -T12t- |
Connector assignment: |
1 - | Front sender, pin 3 - |
2 - | Front sender, pin 1 + |
3 - | Front parking aid warning buzzer -H22- Pin 2 - |
4 - | Front parking aid warning buzzer -H22- Pin 1 + |
5 - | Front left parking aid sender -G255- Pin 2 signal |
6 - | Front centre left parking aid sender -G254- Pin 2 signal |
7 - | Front centre right parking aid sender -G253- Pin 2 signal |
8 - | Front right parking aid sender -G252- Pin 2 signal |
9 - | Front left sender for park assist steering on left side of vehicle -G568- Pin 2 signal |
10 - | Front right sender for park assist steering on right side of vehicle -G569- Pin 2 signal |
11 - | Vacant |
12 - | Vacant |
D - | 12-pin connector -T12n- |
Connector assignment: |
1 - | Vacant |
2 - | Rear centre right parking aid sender -G205- Pin 2 signal |
3 - | Rear centre left parking aid sender -G204- Pin 2 signal |
4 - | Rear right parking aid sender -G206- Pin 2 signal |
5 - | Rear left parking aid sender -G203- Pin 2 signal |
6 - | Vacant |
7 - | Vacant |
8 - | Rear sender Pin 3 - |
9 - | Vacant |
10 - | Vacant |
11 - | Rear sender, pin 1 + |
12 - | Vacant |
Back to overview |
|
Connector assignment: |
A = 11-pin connector -T11b- on wiring harness |
1 - | Terminal 30 |
2 - | Right dipped beam bulb/ right gas discharge light control unit |
3 - | Right main beam bulb (not for xenon) |
4 - | Right fog light bulb |
5 - | Right dipped beam screen motor (xenon) |
6 - | Front right turn signal bulb |
7 - | Left side light bulb |
8 - | Vacant |
9 - | Earth |
10 - | Fuel pump control unit |
11 - | Terminal 50 voltage supply relay |
B = 12-pin connector -T12a- on wiring harness: |
1 - | Right reversing light bulb, automatic anti-dazzle interior mirror |
2 - | Vacant |
3 - | Vacant |
4 - | Rear left fog light bulb |
5 - | Right brake light bulb |
6 - | Vacant |
7 - | Footwell lighting bulb front left, footwell lighting bulb front right |
8 - | Vacant |
9 - | Right tail light bulb |
10 - | Rear right turn signal bulb |
11 - | Left interior light, right interior light, button illumination bulb |
12 - | Terminal 58d |
Back to overview |
C = 12-pin connector -T12m- on wiring harness: |
1 - | Heated driver seat control unit, heated front passenger seat control unit |
2 - | Left brake light bulb |
3 - | Vacant |
4 - | Vacant |
5 - | Vacant |
6 - | Vacant |
7 - | Vacant |
8 - | Number plate light |
9 - | Additional brake light bulb |
10 - | Left tail light bulb |
11 - | Rear left turn signal bulb |
12 - | Left reversing light bulb (only models without rear left fog light bulb) |
D = 11-pin connector -T11c- on wiring harness: |
1 - | Terminal 30 |
2 - | Left fog light bulb |
3 - | Left headlight main beam bulb |
4 - | Left headlight dipped beam bulb |
5 - | Earth |
6 - | Left dipped beam screen motor |
7 - | Bridge to T8a/2- |
8 - | Headlight washer system relay |
9 - | Vacant |
10 - | Right side light bulb |
11 - | Front left turn signal bulb |
E = 16-pin connector -T16k- on wiring harness: |
1 - | Lighting switch terminal 58 |
2 - | Brake light switch |
3 - | Vacant |
4 - | Vacant |
5 - | Vacant |
6 - | Fog light switch |
7 - | Earth (only models with manual gearbox not for American markets) |
7 - | Clutch position sender (only models with manual gearbox for American markets) |
8 - | Lighting switch terminal 56 |
9 - | Vacant |
10 - | Vacant |
11 - | Vacant |
12 - | Vacant |
13 - | Rear fog light switch |
14 - | Light switch, driving light assist |
15 - | Vacant |
16 - | Light switch (daytime running lights) |
Back to overview |
F = 8-pin connector -T8a- on wiring harness: |
1 - | Terminal 50 voltage supply relay |
2 - | Bridge to Connector -T11c/7- |
3 - | Windscreen wiper motor, rain and light sensor (LIN bus) |
4 - | Alternator -C- |
5 - | Bonnet contact switch |
6 - | Vacant |
7 - | Terminal 30 |
8 - | Terminal 31 |
G = 12-pin connector -T12n- on wiring harness: |
1 - | Steering column electronics control unit terminal 50 |
2 - | Indicator lamp for hazard warning light |
3 - | Vacant |
4 - | Switch and instrument illumination regulator |
5 - | Vacant |
6 - | Vacant |
7 - | Convenience CAN bus low |
8 - | Convenience CAN bus high |
9 - | Hazard warning light switch |
10 - | Switch and instrument illumination regulator |
11 - | Steering column electronics control unit terminal 15 |
12 - | Switch and instrument illumination regulator |
H = 12-pin connector : |
- | Pin connector H is vacant. |
Back to overview |
I = 2-pin connector -T2z- on wiring harness: |
1 - | Fuses terminal 30 |
2 - | Terminal 75a |
J = 6-pin connector -T6l- on wiring harness: |
1 - | Washer pump fuse |
2 - | Washer pump |
3 - | Horn fuse |
4 - | Washer pump |
5 - | Earth |
6 - | Treble tone horn, bass tone horn |
K = 10-pin connector -T10- on wiring harness: |
1 - | Heated rear window |
2 - | Vacant |
3 - | Vacant |
4 - | Vacant |
5 - | Fuse terminal 30 |
6 - | Heated rear window fuse |
7 - | Vacant |
8 - | Vacant |
9 - | Vacant |
10 - | Terminal 30g |
L = 2-pin connector -T2- - on wiring harness: |
1 - | Fuse terminal 30 |
2 - | Interior terminal 15 |
Back to overview |
|