DescriptionThe front courtesy light includes two bulbs with three control switches.one of the lights only can be turned on using the external switches;the centre switch can be used to turn on both the lights constantly or with the delay function, as described below, or it can be used to disactivate them both.On versions with a sun roof there are two side rear courtesy lights, both with one bulb only, which can be switched on or off using the relevant switch.the centre switch can be used to turn on both the lights constantly or with the delay function, as described below, or it can be used to disactivate them both.when one of the doors is opened, the courtesy light is timed to stay on for 3 minutes and this function is reactivated each time one of the doors is opened;if a door remains open for longer than three minutes, the courtesy lights go out and remain off until one of the doors is next opened;If, during this period of 3 minutes, all the doors are closed again, a second period of 10 seconds is activated and is interrupted if the ignition key is turned on;when the doors are opened using the remote control (door unlocking), the front courtesy lights come on for 10 seconds; the timing is interrupted if the ignition key is turned ON;when the vehicle is locked (door locking) the courtesy lights go off;when the ignition key is turned OFF and extracted (the Body Computer checks that there is no Transponder): the courtesy lights are activated for 10 seconds;the courtesy lights are also turned on if the inertia switch is operated (the information is sent via the instrument panel CAN). for a period of 15 minutes.The switching on and off takes place gradually (dimmer) with a cycle lasting 2 seconds.If one or more of the doors is open, this is shown on the instrument panel display; in addition, the warning light remains on until all the vehicle doors and the boot are perfectly closed. In addition if this signal is associated with a particular speed threshold being surpassed, an acoustic signal is activated.The power supply for all the courtesy lights follows the battery voltage control logic (SBMT); with the ignition OFF, when any of the doors or the boot is opened, or if the doors are unlocked, the timer is set at 15 minutes after which all the courtesy lights are deactivated.
Functional description The Body Computer M1 receives door open input signals at pin 8 of connector D (driver side front door) and pin 16 of connector D (left rear door), pin 25 of connector E (front passenger door), pin 26 of connector E (right rear door) and, lastly, pin 36 of connector E (boot). According to the SBMT control logic described previously, both the front courtesy light G10 and the rear courtesy lights G25 and G26 are supplied by the Body Computer M1 from pin 33 of connector E through the direct line protected by fuse F39 of the junction unit under the dashboard B2 . The front courtesy light G10 is also controlled by the Body Computer M1 with a timed earth signal from pin 21 of connector E. The Body Computer M1 is connected to the instrument panel E50 via the CAN line:from the latter it receives the 'inertia switch operated' signal and this information is shown on the display and lights up the general failure warning light.a signal is sent, when necessary, which lights up the doors open warning light and, at the same time, the information is shown on the display.
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b).2050746
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212400802-7040A37fuse box cover - r r1. Disconnect the electrical connections (1a, 1b, 1c, 1d, 1e, 1f).2. Undo the bracket retaining bolt.3. Slightly move the bracket (3a) for the dashboard trim and undothe bolt (3b).4. Undo the other bolts securing the body computer/junction unit.5. Slightly move the body computer/junction unit assembly.6. Disconnect the electrical connections (6a, 6b, 6c).7. Recover the body computer/junction unit.2050752
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect electronic control unit electrical connections (1a),(1b), (1c).2. Undo the bolts.3. Recover the control unit.2050753
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect electronic control unit electrical connections (1a),(1b), (1c).2. Undo the bolts.3. Recover the control unit.2050754
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Prise out courtesy light (1a) by undoing retainers (1b).2. Move aside the courtesy light unit and disconnect the electricalconnection.3. Keep the courtesy light.2051106
7040E12
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Prise out courtesy light (1a) by undoing the retainers (1b).2. Move aside the courtesy light unit and disconnect the electricalconnection.3. Keep the courtesy light.2051108
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect the electrical connection for the microswitch.2. Undo the bolts.3. Move the lock (3a) slightly and disconnect the electrical connection(3b) for the motor.4. Remove the lock assembly (4a) releasing the emergency openingcable (4c) from the retainers (4b).2400755-7015B70tail-gate lock motor - r r and check lock supplyline , if necessary. 2050996
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect the electrical connection.2. Undo the nuts securing the outer handle.2050999
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Open the cover giving access to the glass retainer.2. Provisionally connect the switch unit to its electrical connection(2a) and move the retainer (2b) of the glass (2c) to the accessposition (as illustrated in the figure). 3. Disconnect the retainer (2b) from the glass, then lift the glass(2c) to the end of its travel and secure it in this position witha hook (3a). 2050882
1. If adjustment is carried out after removing the door, tightenthe hinge bolts to the specified torque. 2. If the hinges had been removed from the door previously, fullytighten the hinge bolts. 3. Undo the bolt (3a) on the check strap (3b) and close the door to push the check strap back in. 4. Loosen the bolts securing the hinges to the bodyshell, usingthe specific tool.5. Adjust the door position, making use of the bolt slots, so thatit is perfectly aligned with the body. 23It is advisable to work on onehinge at a time. Possible adjustment movements are indicated byarrows.2050886
7005A24
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Undo the bolts fixing the hinge to the bodyshell.2. Remove the hinge (2a) and collect any shims (2b).2050888
7005A25
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Open the door and undo the bolt.2. Recover the bracket.2050890
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Open the door and remove the seal.2050896
Passenger front. door lock geared motor
N51
N51
Left rear. door lock geared motor
N55
rear side door assembly
7010A08
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Open the cover giving access to the glass retainer.2. Provisionally connect the switch unit to the electrical connection(2a) and move the retainer (2b) of the glass (2c) to the accessposition (as illustrated in the figure). 3. Disconnect the retainer (2b) from the window, then lift the glass(2c) to the end of its travel and secure it in this position witha hook (3a). 4. Disconnect the electrical connection.2050937
1. If adjustment is made after removing the door, tighten the hingebolts to the specified torque. 2. If the hinges were removed from the door previously, tightenthe hinge bolts. 3. Undo the bolt (3a) of the door check strap (3b) and close thedoor again to push the check strap back in. 2050941
7010A24
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Undo the bolts fixing the hinge to the bodyshell.2. Remove the hinge (2a) and collect any shims (2b).2050943
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Open the door and remove the seal.2050950
7010A50
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Open the door and remove the seal.2050951
Rear door lock geared motor right
N56
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Čeština
Dansk
Deutsch
Ελληνικά
English
English
Español
Suomi
Français
Français
עברית
Hrvatski
Magyar
Italiano
日本語
한국어
Nederlands
Polski
Português
Português
Русский
Slovenčina
Slovenščina
Svenska
Türkçe
中文 (中国)
