All Wiring Diagrams for Isuzu Pickup S 1995 model – Sheme ožičenja za avtomobile

AIR CONDITIONING

A/C Wiring Diagram for Isuzu Pickup S 1995

List of elements for A/C Wiring Diagram for Isuzu Pickup S 1995:

(2.3l)
(2.3l: in fuse/relay box)
(2.6l)
2.3l
2.6l
A/c compressor clutch
A/c dual pressure switch (behind left side of radiator grille)
A/c switch
A/c thermostat relay (2.6l: behind right side of i/p, at kick panel)
Blower motor
C 1995 vftc
C210
C214
C282
C289
C290
Charge relay
Electronic thermostat (behind glove box)
Engine control module (at left kick panel)
Evaporator temperature sensor
Fast idle solenoid valve (right rear of engine)
Fast idle solenoid valve (right side of engine compartment on inner fender panel)
Fuse 7 20a
Fuse 8 10a
Fuse/ relay box
G101 (right side of engine compartment)
G119 (right front of engine, on intake manifold)
G202 (below left side of i/p, behind ecm)
G203 (at right kick panel)
Heater- a/c relay
Heater-a/c control panel
Hot at all times
Interior lights system
Main fuse 1 60a
Nca
Off
Resistor block (behind glove box)
Solid state

Heater Wiring Diagram for Isuzu Pickup S 1995

Získajte prístup ku všetkým schémam zapojenia automobilu

List of elements for Heater Wiring Diagram for Isuzu Pickup S 1995:

Blower motor
C282
C289
C290
Charge relay
Fuse 7 20a
Fuse/ relay box
G101 (right side of engine compartment)
G203 (at right kick panel)
Heater- a/c relay
Heater-a/c control panel
Hot at all times
Interior lights system
Main fuse 1 60a
Nca
Off
Resistor block (behind glove box)

ANTI-LOCK BRAKES

Anti-lock Brake Wiring Diagrams for Isuzu Pickup S 1995

Získajte prístup ku všetkým schémam zapojenia automobilu

List of elements for Anti-lock Brake Wiring Diagrams for Isuzu Pickup S 1995:

(at parking
(below right front seat)
(left i/p)
(mounted on brake
4wd ind.
4wd indicator switch (right side of transfer case)
4wd switch in
Battery in
Brake
Brake ind.
Brake ind. ctrl
Brake light
Brake switch
Brake switch in
Brake valve (right rear
Charging system
Combination valve pressure differential switch (in brake fluid valve)
D.g. conn. in
D.g. connector (left kick panel)
Dash fuse box
Differential speed sensor (on top of differential)
Diode box d (behind left i/p, taped to harness)
Dump solenoid
Dump solenoid ctrl
Engine compt)
Fuse 10a
Fuse 20a
G105 (right rear fender)
G301
Ground
Hot at all times
Hot in on
Hot in on or start
Ignition in
Indicators
Instrument cluster
Iso solenoid ctrl
Isolation solenoid
Or acc
Parking
Pedal
Pnk/
Press. switch in
Rabs ind. ctrl
Rear wheel anti-lock
Rear wheel anti-lock brake controller (below right front seat)
Red
Red/
Release)
Reset switch
Reset switch in
Rr. anti- lock brake ind.
Speed sensor-hi
Speed sensor-lo
Support)
Switch
Test connector (left kick panel)

COMPUTER DATA LINES

2.3L

2.3L, Computer Data Lines for Isuzu Pickup S 1995

Získajte prístup ku všetkým schémam zapojenia automobilu

List of elements for 2.3L, Computer Data Lines for Isuzu Pickup S 1995:

"check engine" malfunction indicator lamp (mil)
(rear of left front fender)
(right side of engine)
C274
Dash fuse box (left side of i/p)
Data link connector (left kick panel)
Diagnostic trouble code terminal (left kick panel)
Dlc/dtc input
Engine control module (left kick panel)
Fuse 10a
G104
G120
Hot in on or start
Instrument cluster
Mil control

2.6L

2.6L, Computer Data Lines for Isuzu Pickup S 1995

Získajte prístup ku všetkým schémam zapojenia automobilu

List of elements for 2.6L, Computer Data Lines for Isuzu Pickup S 1995:

"check engine" malfunction indicator lamp (mil)
(right side of engine)
C274
C275
Dash fuse box (left i/p)
Data link connector (left kick panel)
Diagnostic trouble code terminal (left kick panel)
Dlc/dtc input
Engine control module (left kick panel)
Fuse 10a
G120
Hot in on or start
Instrument cluster
Mil control

DEFOGGERS

Heated Mirrors Wiring Diagram for Isuzu Pickup S 1995

Získajte prístup ku všetkým schémam zapojenia automobilu

List of elements for Heated Mirrors Wiring Diagram for Isuzu Pickup S 1995:

(behind right side of i/p, above kick panel)
(left side kick panel)
15a
Dash fuse box (left side of i/p)
Defogger switch
Door mirror switch
Fuse 6
G200
G201
Hot in on or start
Interior lights system
Left door mirror
Off
On indicator
Right door mirror

ENGINE PERFORMANCE

2.3L

2.3L, Engine Performance Wiring Diagrams (1 of 2) for Isuzu Pickup S 1995

Získajte prístup ku všetkým schémam zapojenia automobilu

List of elements for 2.3L, Engine Performance Wiring Diagrams (1 of 2) for Isuzu Pickup S 1995:

"check engine" malfunction indicator lamp (mil)
(left side of engine compartment, on inner fender panel)
(right side of engine compartment, on inner fender panel)
(top center of engine, on rear of carburetor)
A/c on input
Air conditioning system
Air inj react vsv cont
Air management valve (amv)
C213
C214
C221
C222
C274
C275
Dash fuse box (left side of i/p, behind panel)
Data link connector (dlc) (below left side of i/p, at kick panel)
Diagnostic trouble code (dtc) terminal (below left side of i/p, at kick panel)
Dlc/dtc input
Duty sol control
Duty solenoid (top center of engine, in front of carburetor)
Dwell lead (right side of engine compartment, taped to harness)
Ect sensor input
Efe heater relay cont
Egr vsv control
Engine control module (ecm) (below left side of i/p, at kick panel)
Engine control module (ecm) relay
Engine rpm input
Evap cnstr purge vsv
Evaporative emission canister purge vacuum switching valve (right side of engine compartment, on inner fender panel)
Exhaust gas recirculation (egr) vacuum switching valve (calif only)
Exhaust gas temp sen
Fuse 1 10a
Fuse 3 10a
Fuse 7 10a
Fuse 8 10a
Fuse/relay box (right side of engine compartment, on inner fender panel)
G101 (right side of engine compartment, on inner fender panel)
G104 (left rear corner of engine compartment, on inner fender panel)
G131 (right side of engine, on intake manifold)
Ground
Hot at all times
Hot in on or start
Idle vacuum switch in
Ignition input
Instrument cluster
Manifold absolute pressure (map) vacuum switching valve
Map sensor input
Map vsv control
Mil control
Oxygen sensor (lower left side of engine, in exhaust manifold)
Oxygen sensor input
Power input
Ref voltage
Slow cut sol control
Slow cut solenoid
Vss input

2.3L, Engine Performance Wiring Diagrams (2 of 2) for Isuzu Pickup S 1995

Získajte prístup ku všetkým schémam zapojenia automobilu

List of elements for 2.3L, Engine Performance Wiring Diagrams (2 of 2) for Isuzu Pickup S 1995:

(right side of engine, in intake manifold)
Accelerator switch (below left side of i/p, on top of accelerator pedal)
C274
Charge relay
Charging system
Choke heater
Dash fuse box (left side of i/p, behind panel)
Distributor assembly (right rear corner of engine)
Distributor cap
Efe heater (right side of engine, below caburetor)
Efe heater relay
Engine coolant temperature (ect) sensor
Exhaust gas temperature sensor (calif. only) (lower right side of engine compartment, below intake manifold)
Fuse 2 10a
Fuse 6 10a
Fuse 9 15a
Fuse/relay box (right side of engine compartment, on inner fender panel)
Fuse/relay box (right side of engine compartment, on inner fender panel)
G105 (right side of engine compartment, on inner fender panel)
Generator (lower left of engine)
Ground
Heater
Hot at all times
Hot in on or start
Idle vacuum switch (right side of engine compartment, on inner fender panel)
Ignition coil (right rear corner of engine)
Ignition control module solid- state: do not check resistance
Ignition vacuum switching valve (right side of engine compartment on inner fender panel)
Indicator control
Instrument cluster
Main fuse 1 60a
Manifold absolute pressure (map) sensor (right side of of engine compartment, on inner fender panel)
Nca
Noise condenser (right side of engine, on intake manifold)
Pick- up coil
Pick-up coil control
Power
Primary
Primary output control
Secondary
Spark plugs
Timer core
Vehicle speed sensor
Voltage regulator
Wire coil

2.6L

2.6L, Engine Performance Wiring Diagrams (1 of 3) for Isuzu Pickup S 1995

Získajte prístup ku všetkým schémam zapojenia automobilu

List of elements for 2.6L, Engine Performance Wiring Diagrams (1 of 3) for Isuzu Pickup S 1995:

"check engine" malfunction indicator lamp (mil)
(top center of engine)
A/c on input
A/c system
A/t only
Air cntrl vsv cntrl
C207
C208
C210
C211
C274
C275
Dash fuse box (left side of i/p, behind panel)
Data link connector (dlc) (below left side of i/p, at kick panel)
Diagnostic trouble code (dtc) terminal (below left side of i/p, at kick panel)
Dtc/dlc input
Ect sensor input
Egr duty sol cntrl
Egr vsv cntrl
Engine control module (ecm) (below left side of i/p, at kick panel)
Evap can purg vsv
Fuel inj no.1 cntrl
Fuel inj no.2 cntrl
Fuel inj no.3 cntrl
Fuel inj no.4 cntrl
Fuel injector no.1
Fuel injector no.2
Fuel injector no.3
Fuel injector no.4
Fuel pres cntrl vsv
Fuse 12 10a
Fuse 3 10a
Fuse 7 10a
Fuse 8 10a
G105 (right side of engine compartment on inner fender panel)
G120 (right side of engine, on intake manifold)
Ground
Hot at all times
Hot in on or start
Hot in start
Idle input
Ignition switch input
Input
Instrument cluster
Map sensor input
Mil cntrl
Not used
Oxygen sensor input
Park/neutral position switch (right side of transmission)
Power
Power input
Power signal input
Red
Reference voltage
Shield ground
Signal input
Starting/ charging system (diode box b, in fuse/relay box)
Starting/ charging system (starter relay)
Trans posit input
Vehicle speed input
Wide open throttle

2.6L, Engine Performance Wiring Diagrams (2 of 3) for Isuzu Pickup S 1995

Získajte prístup ku všetkým schémam zapojenia automobilu

List of elements for 2.6L, Engine Performance Wiring Diagrams (2 of 3) for Isuzu Pickup S 1995:

(lower right side of engine, below intake manifold)
(right side of engine compartment, on inner fender panel)
(top center rear of engine on valve cover)
(top center rear of engine, on valve cover)
Air flow sensor (solid state: do not measure resistance) (left front of engine compartment, on air flow sensor)
Air flow sensor shield
Air management valve (amv) (left front of engine compartment, right of airflow assembly)
C274
Cluster
Diode box b
Electronic control module (ecm) relay
Engine coolant temperature (ect) sensor
Evaporative emission canister purge vacuum switching valve
Exhaust gas recirculation (egr) duty solenoid (calif. only)
Exhaust gas recirculation (egr) vacuum switching valve (calif. only)
Fuel pressure control valve vacuum switching valve
Fuse 1 15a
Fuse/relay box (right side of engine compartment, on inner fender panel)
G105 (right side of engine compartment, on inner fender panel)
Ground
Hot at all times
Idle
Instrument
Manifold absolute pressure (map) sensor (right side of engine compartment, on inner fender panel)
Output
Power
Red
Vehicle speed sensor (vss)
Wide open throttle (wot) switch (top center rear of engine, on throttle assembly)
Wot

2.6L, Engine Performance Wiring Diagrams (3 of 3) for Isuzu Pickup S 1995

Získajte prístup ku všetkým schémam zapojenia automobilu

List of elements for 2.6L, Engine Performance Wiring Diagrams (3 of 3) for Isuzu Pickup S 1995:

(not used)
Air conditioning system
Air regulator (lower right rear of engine, below intake manifold)
Braided wire
C134
C274
C275
Charge relay
Charging system
Coil wire
Crankshaft position sensor (solid state: do not check resistance) (right rear of engine, in bottom of distributer assembly)
Dash fuse box (left side of i/p, behind panel)
Diode box a
Distributer assembly (top right rear corner of engine)
Distributer cap
From oil pressure switch
Fuel pump (beneath truck bed, in top of fuel tank)
Fuel pump relay
Fuse 11 20a
Fuse 2 20a
Fuse 6 10a
Fuse 7 10a
Fuse 9 15a
Fuse/relay box (right side of engine compartment, on inner fender panel)
Fuse/relay box (right side of engine compartment, on inner fender panel)
G105 (right side of engine compartment, on inner fender panel)
G119 (right front of engine, on intake manifold)
G120 (right side of engine on intake manifold)
G202 (below left side of i/p behind engine control module)
G409 (beneath truck bed on rear of right frame rail)
Generator (lower left front of engine)
Ground
Heated oxygen sensor (ho2s) (lower left side of engine, in exhaust manifold)
Hot at all times
Hot in on or start
Hot in start
Ignition coil (top center rear of engine, on valve cover)
Indicator control
Instrument cluster
Main fuse 1 60a
Nca
Noise condensor (top center rear of engine, on valve cover)
Power
Power distrib- ution system
Power signal input
Power switch (solid state: do not check resistance) (right side of engine, below intake manifold)
Primary
Primary winding control
Red
Reference voltage
Secondary
Signal output
Spark plugs
Tachometer (solid-state: do not check resistance)
Tachometer test connector (right side of engine compartment, behind fuse/ relay box)
Timer core
Voltage regulator

EXTERIOR LIGHTS

Back-up Lamps Wiring Diagram for Isuzu Pickup S 1995

Získajte prístup ku všetkým schémam zapojenia automobilu

List of elements for Back-up Lamps Wiring Diagram for Isuzu Pickup S 1995:

Back up lights switch (on left side of transmission)
Dash fuse box (left side of i/p)
Exterior lights system
Fuse 10a
G417 (beneath truck bed, on rear of right frame rail)
Hot in on or start
Left back up light
Left taillight assembly
Right back up light
Right taillight assembly

Exterior Lamps Wiring Diagram for Isuzu Pickup S 1995

Získajte prístup ku všetkým schémam zapojenia automobilu

List of elements for Exterior Lamps Wiring Diagram for Isuzu Pickup S 1995:

(beneath truck bed, on rear of right frame rail)
(left rear of eng compt, on inner fender panel)
(left side kick panel)
(rear of left fender)
10a
15a
Brake light switch (on brake pedal support)
C274
C275
Dash fuse box (left side of i/p)
Flasher unit (behind left side of i/p, above kick panel)
Fuse 1
Fuse 2
Fuse 3
Fuse 7
Fuse/ relay box (right side of eng compt)
G104
G200
G417
Gnd
Hazard
Head
Headlights system
High mount stop lamp
Hot at all times
Hot in on or start
Instrument cluster
Interior lights system
Left front combination light
Left front side marker light
Left taillight assembly
Left turn
License lights
Light switch
Off
Output
Park
Park/ stop light
Power
Red
Right front combination light
Right front side marker light
Right taillight assembly
Right turn
Stop
Turn
Turn signal ind.
Turn signal light
Turn signal/ hazard warning switch (combination switch)
W/ rear bumper

GROUND DISTRIBUTION

Ground Distribution Wiring Diagram (1 of 2) for Isuzu Pickup S 1995

Získajte prístup ku všetkým schémam zapojenia automobilu

List of elements for Ground Distribution Wiring Diagram (1 of 2) for Isuzu Pickup S 1995:

2.3l
2.3l only
2.6l
4wd indicator switch
Air regulator
Battery
Braided wire
C213
C214
Charge relay
Data link connector (dlc)
Diagnostic trouble code (dtc) terminal
Ecm relay
Efe heater
Engine control module (ecm)
Fast idle solenoid valve
Fuel pump relay no.1
Fuse/ relay box
G101 (right front fender)
G104 (rear of left fender)
G115 (rear of engine)
G119 (right front of engine)
G120 (right side of engine)
G130 (left top side of transaxle)
G131 (intake manifold)
Heated oxygen sensor (ho2s)
Heater- a/c relay
Ignition vacuum switching valve
Left front combination light
Left front side marker light
Rear wheel anti-lock brake valve
Right front combination light
Right front side marker light
Windshield washer motor
Windshield wiper motor
Windshield wiper relay or connector plug

Ground Distribution Wiring Diagram (2 of 2) for Isuzu Pickup S 1995

Získajte prístup ku všetkým schémam zapojenia automobilu

List of elements for Ground Distribution Wiring Diagram (2 of 2) for Isuzu Pickup S 1995:

(not used)
2.6l
2.6l 4wd pickup
Back up
Braided wire
C210
C211
C224
C314
Cigarette lighter
Combination switch
Crankshaft position sensor
Crankshaft position sensor shield
Data link connector (dlc)
Defogger switch
Diagnostic trouble code (dtc) terminal
Door mirror switch
Driver's seat belt switch
Engine control module (ecm)
Flasher unit
Fuel pump
Fuel tank unit
G131 (intake manifold)
G200 (left side kick panel)
G201 (right side of i/p)
G301 (below right front seat)
G409 (rear of cargo bed)
Heater and a/c control panel
Heater- a/c control panel
High mount stop lamp
Illumination controller
Instrument cluster
Left door mirror
Left license light
Left taillight assembly
License light
Light switch
Overdrive off switch
Park/stop
Radio
Rear wheel anti-lock controller
Remind buzzer control unit
Right license light
Right power mirror
Right taillight assembly
Safety lock controller
Turn
W/ rear bumper
W/o rear bumper

HEADLIGHTS

Headlight Wiring Diagram for Isuzu Pickup S 1995

Získajte prístup ku všetkým schémam zapojenia automobilu

List of elements for Headlight Wiring Diagram for Isuzu Pickup S 1995:

(left side kick panel)
(right side of safety wall)
10a
15a
Battery
C274
Dash fuse box (left side of i/p)
Dimmer/ passing switch (combination switch)
Dimming switch
Exterior lights system
Flash to pass switch
Fuse 10
Fuse 6
Fuse 9
Fuse/ relay box (right side of eng compt)
G123
G200
Head
Head- light relay
High beam indicator light
Hot at all times
Hot in on or start
In-line fuse 15a (right side of eng compt, near fuse/ relay box)
Instrument cluster
Interior lights system
Left headlamp
Left off-road light
Light switch
Main fuse 2 30a
Off
Off- road lights relay (right rear of eng compt)
Off- road lights switch
Park
Red
Right headlamp
Right off-road light
Splice connector (behind left side of i/p, near fuse relay box)

HORN

Horn Wiring Diagram for Isuzu Pickup S 1995

Získajte prístup ku všetkým schémam zapojenia automobilu

List of elements for Horn Wiring Diagram for Isuzu Pickup S 1995:

(behind right side of radiator grille)
10a
2.6l only
Contact ring
Fuse 4
Fuse/ relay box (right side of eng compt)
Horn switch
Horn switches
Hot at all times
Low note horn (behind right side of radiator grille)

INSTRUMENT CLUSTER

Instrument Cluster Wiring Diagram for Isuzu Pickup S 1995

Získajte prístup ku všetkým schémam zapojenia automobilu

List of elements for Instrument Cluster Wiring Diagram for Isuzu Pickup S 1995:

(2.3l) (2.6l)
(left side kick panel)
(right front fender)
10a
2.3l
2.6l
4wd indicator light
4wd indicator switch (on right side of transmission)
A10
A11
A12
B10
B11
B12
Brake warning light
C214 c211
C274
C275
Charge warning light
Combination valve pressure differential switch (left rear of eng compt, in brake fluid valve)
Dash fuse box (left side of i/p)
Diode box d (behind left side of i/p, taped to harness)
Engine control module (left side of i/p, at kick panel)
Engine controls system
Engine controls system (diode box a)
Engine controls system (ecm)
Engine coolant temperature (ect) gauge sender (right front of eng, below intake manifold)
Engine coolant temperature gauge
Exterior lights system
Fuel gauge
Fuel tank unit (right side fuel tank)
Fuse 7
G101
G200
G417 (beneath truck bed, on rear of right frame rail)
Head- lights system
Hi beam indicator light
Hot in start
Ignition coil (top center of eng, on valve cover)
Illumination (w/o tacho- meter: 2 bulbs, w/ tacho- meter: 9 bulbs)
Instrument cluster
Interior lights system
Internal voltage regulator
Left turn signal indi- cator light
Low fuel warning light
Malfunction indicator lamp (mil) (check engine)
O2 sensor indicator light
Oil pressure gauge
Oil pressure sending unit (w/ tachometer) (lower right front of eng, near oil filter)
Oil pressure switch (lower right rear of eng, above oil pan)
Oil pressure warning light
Parking brake switch (on parking brake lever)
Pnk
Rear anti- lock brake warning light
Rear wheel anti-lock brake controller (below right front seat)
Right turn signal indi- cator light
Seat belt warning light
Starting/ charging system
Tachometer (2.6l)
Vehicle speed sensor
Voltage meter
Warning systems