ANTI-LOCK BRAKES – Dodge Cab & Chassis R2500 1997 – SYSTEM WIRING DIAGRAMS

ANTI-LOCK BRAKES

All-Wheel ABS Wiring Diagram for Dodge Cab & Chassis R2500 1997

List of elements for All-Wheel ABS Wiring Diagram for Dodge Cab & Chassis R2500 1997:

• (behind knee bolster) joint connector c
• (engine harn, in breakout to abs mod) s158
• (engine harn, in breakout to abs module) s208
• (engine harn, near breakout to abs module) s109
• (in breakout to hcu) s112
• (right fender side shield)
• (top of rear differential) rear wheels sensor
• 4 x 4 ind
• 4wd switch input
• 4x4 switch (on front of frame)
• 87a
• A20
• Abs 2-way power feed (left fender side shield)
• Abs lamp relay ctrl
• Abs pump relay (in power distribution center)
• Abs pump relay ctrl
• Abs warn ind
• Abs warning ind ctrl
• Abs warning lamp relay (in power distribution center)
• Acc
• Anti-lock brake system control module (left fender side shield)
• B113
• B114
• B116
• B120
• B18
• B19
• B243
• B245
• B248
• B249
• B252
• B254
• B47
• B60
• Brake warn indic.
• Brake warning ind
• Brake warning switch (on left frame rail)
• D11
• D12
• Data link connector (left bottom of i/p)
• Data link input
• Data link output
• Dump sol
• Engine controls (pcm)
• Fuse 20a
• Fuse 40a
• Fuse block
• G100 (left fender shield)
• G100 (left fender side shield)
• G101
• G104 (fender shield)
• G107
• G19
• G206 (i/p right center support)
• Ground
• Ground joint (near pdc)
• Hot at all times
• Hot in run
• Hydraulic control unit (rear of abs pump)
• Ignition
• Ignition switch
• Instrument cluster
• Isolate sol
• Left front reset
• Left front wheel sensor
• Left isolation and dump solenoids
• Lt frnt isolate sol ctrl
• Lt front dump ctrl
• Lt front wheel sensor
• Off
• Power distribution center
• Pump motor ctrl
• Pump motor feed
• Rear dump sol ctrl
• Rear isolate sol ctrl
• Rear reset
• Rear wheels sensor
• Red
• Reset sw
• Right front reset
• Right front wheel sensor
• Rt frnt isolate sol ctrl
• Rt front dump sol ctrl
• Rt front wheel sensor
• Rt isolation and dump solenoids
• Run
• Rwal valve (below master cylinder)
• S103
• S105 (engine harn, in breakout to horn)
• S108
• S110 (in breakout to abs mod)
• S208
• Start
• Stop lamp switch
• Stop lamp switch (on brake pedal bracket)
• V40
• Vacuum sensor (diesel only) (left fender side shield)

Rear Wheel ABS Wiring Diagram for Dodge Cab & Chassis R2500 1997

List of elements for Rear Wheel ABS Wiring Diagram for Dodge Cab & Chassis R2500 1997:

• (left bottom of i/p) data link connector
• 4wd indicator
• 4wd switch input
• 4x4 switch (on front of frame)
• A20
• Abs warning ind ctrl
• Abs warning lamp
• Acc
• B101
• B108
• B111
• B112
• B113
• B114
• Brake sw input
• Brake warning
• Brake warning lamp
• Brake warning switch (left side frame rail)
• Diagnostic signal
• Diesel
• Dump sol
• F32
• Fuse 20a
• Fuse block
• Fused b(+)
• Fused ign (run)
• G100 (left fender side shield)
• G104 (left fender shield)
• G107
• G11
• G19
• G206 (i/p right center support)
• Gasoline
• Ground
• Ground joint (near pdc)
• Hot at all times
• Hot in run
• Ignition switch
• Instrument cluster
• Isolate sol
• Joint connector b (near rear of fuse block)
• Joint connector c (behind knee bolster)
• Off
• Park brake indic.
• Park brake input
• Park brake switch (on brake bracket)
• Rear wheel anti-lock control module (center of i/p)
• Rear wheel sensor (+)
• Rear wheel sensor (-)
• Rear wheel speed sensor (left frame rail, near fuel tank)
• Reset
• Reset sw
• Run
• Rwal dump solenoid
• Rwal hydraulic valve (below master cylinder)
• Rwal isolate solenoid
• S103
• S109 (engine harn, near breakout to abs module)
• S208
• Start
• Stop lamp switch (brake pedal bracket)
• V40
• Vacuum sensor (diesel only) (left fender side shield)