Čeština
Dansk
Deutsch
Ελληνικά
English
English
Español
Suomi
Français
Français
עברית
Hrvatski
Magyar
Italiano
日本語
한국어
Nederlands
Polski
Português
Português
Română
Русский
Slovenčina
Slovenščina
Türkçe
中文 (中国)
Wiring Diagram VW JETTA NF 2016 - Mechatronic unit for dual clutch gearbox
| G487 | Gear selector movement sensor 1 |
| G488 | Gear selector movement sensor 2 |
| J743 | Mechatronic unit for dual clutch gearbox |
| N433 | Valve 1 in sub-gearbox 1 |
| N434 | Valve 2 in sub-gearbox 1 |
| N435 | Valve 3 in sub-gearbox 1 |
| N436 | Valve 4 in sub-gearbox 1 |
| N437 | Valve 1 in sub-gearbox 2 |
| N438 | Valve 2 in sub-gearbox 2 |
| N439 | Valve 3 in sub-gearbox 2 |
| N440 | Valve 4 in sub-gearbox 2 |
| SB1 | Fuse 1 on fuse holder B |
| SB2 | Fuse 2 on fuse holder B |
| T25 | 25-pin connector |
| 150 | Earth connection 2 in automatic gearbox wiring harness |
| 641 | Earth point 3, left in engine compartment |
Wiring Diagram VW JETTA NF 2016 - Mechatronic unit for dual clutch gearbox - Fuse 13 on fuse holder C - Diagnostic connection
| G270 | Gearbox hydraulic pressure sender |
| G489 | Gear selector movement sensor 3 |
| G490 | Gear selector movement sensor 4 |
| G510 | Temperature sender in control unit |
| G612 | Gearbox input speed sender 2 |
| G617 | Clutch travel sender 1 |
| G618 | Clutch travel sender 2 |
| G632 | Gearbox input speed sender 1 |
| J743 | Mechatronic unit for dual clutch gearbox |
| SC13 | Fuse 13 on fuse holder C |
| T16 | 16-pin connector |
| T25 | 25-pin connector |
| U31 | Diagnostic connection |
| V401 | Hydraulic pump motor |
| D51 | Positive connection 1 (15), in engine compartment wiring harness |
Wiring Diagram VW JETTA NF 2016 - Selector lever - Onboard supply control unit - Data bus diagnostic interface - Selector lever sensors control unit - Engine control unit
| E313 | Selector lever |
| J519 | Onboard supply control unit |
| J533 | Data bus diagnostic interface |
| J587 | Selector lever sensors control unit |
| J623 | Engine control unit |
| SC20 | Fuse 20 on fuse holder C |
| T10s | 10-pin connector |
| T20 | 20-pin connector |
| T73b | 73-pin connector |
| T73c | 73-pin connector |
| T94 | 94-pin connector |
| 44 | Earth point, lower part of left A-pillar |
| 366 | Earth connection 1, in main wiring harness |
| 367 | Earth connection 2, in main wiring harness |
| 605 | Earth point, on top end of steering column |
| A19 | Connection (58d), in dash panel wiring harness |
| A116 | Connection 2 (58d), in dash panel wiring harness |
| B172 | Positive connection 4 (30), in interior wiring harness |
| B383 | Connection 1 (powertrain CAN bus, high), in main wiring harness |
| B390 | Connection 1 (powertrain CAN bus, low), in main wiring harness |
| * | see applicable current flow diagram for engine |
Wiring Diagram VW JETTA NF 2016 - Selector lever - Selector lever sensors control unit - Selector lever position display
| E313 | Selector lever |
| J587 | Selector lever sensors control unit |
| T10t | 10-pin connector |
| Y26 | Selector lever position display |
| * | According to equipment |
Wiring Diagram VW JETTA NF 2016 - Selector lever - Selector lever locked in position P switch - Selector lever sensors control unit - Selector lever lock solenoid - Ignition key withdrawal lock solenoid
| E313 | Selector lever |
| F319 | Selector lever locked in position P switch |
| J587 | Selector lever sensors control unit |
| N110 | Selector lever lock solenoid |
| N376 | Ignition key withdrawal lock solenoid |
| T4dr | 4-pin connector |
| T10s | 10-pin connector |
| A167 | Positive connection 3 (30a) in dash panel wiring harness |