DescriptionThe electric windows in the front doors are operated through the switches in the front driver's door (both windows) and the front passenger door (passenger side only).The operation is manual: the glass only goes up/down when the button is pressed. Both windows can only be operated when the ignition is ON.The circuit is operated by the services relay and protected by two fuses, both located in the junction unit under the dashboard: the supply is ensured both the ignition ON and with the ignition OFF: during starting, this relay is temporarily deactivated, whilst with the ignition OFF, the Body Computer keeps the relay activated for 3 minutes, but deactivates it 30 seconds after one of the doors is opened
Functional description The services relay T13, located in the unit under the dashboard B2, supplies with the above-mentioned logic and controlled by the Body Computer M1 - pin 14 of connector F - the switches H44 (electric windows switch in driver's door) and H50 (electric window switch in passenger door) via two lines, protected by the fuses F47 and F48. The same lines supply the LEDs that light up the actual switches. When the switches are operated a supply and earth are sent to the driver's electric window motor N60 or to the passenger one N61; reversing the signals according to the contact which closes, determines the direction of rotation of the motor.
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b).2050746
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212400802-7040A37fuse box cover - r r1. Disconnect the electrical connections (1a, 1b, 1c, 1d, 1e, 1f).2. Undo the bracket retaining bolt.3. Slightly move the bracket (3a) for the dashboard trim and undothe bolt (3b).4. Undo the other bolts securing the body computer/junction unit.5. Slightly move the body computer/junction unit assembly.6. Disconnect the electrical connections (6a, 6b, 6c).7. Recover the body computer/junction unit.2050752
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect electronic control unit electrical connections (1a),(1b), (1c).2. Undo the bolts.3. Recover the control unit.2050753
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect electronic control unit electrical connections (1a),(1b), (1c).2. Undo the bolts.3. Recover the control unit.2050754
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212400682-7005E12corner cover of onefront side door, lh or rh r r1. Undo the bolts.2. Move aside the switch unit.3. Disconnect the electrical connection.4. Disconnect the door opening rod (4a) from the retainers (4b).5. Recover the switch unit with trim.2050926
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect the electric window motor connection.2. Undo the bolts.3. Remove the motor releasing the splined shaft.2050929
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Open the cover giving access to the glass retainer.2. Provisionally connect the switch unit to its electrical connection(2a) and move the retainer (2b) of the glass (2c) to the accessposition (as illustrated in the figure). 3. Disconnect the retainer (2b) from the glass, then lift the glass(2c) to the end of its travel and secure it in this position witha hook (3a). 2050882
1. If adjustment is carried out after removing the door, tightenthe hinge bolts to the specified torque. 2. If the hinges had been removed from the door previously, fullytighten the hinge bolts. 3. Undo the bolt (3a) on the check strap (3b) and close the door to push the check strap back in. 4. Loosen the bolts securing the hinges to the bodyshell, usingthe specific tool.5. Adjust the door position, making use of the bolt slots, so thatit is perfectly aligned with the body. 23It is advisable to work on onehinge at a time. Possible adjustment movements are indicated byarrows.2050886
7005A24
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Undo the bolts fixing the hinge to the bodyshell.2. Remove the hinge (2a) and collect any shims (2b).2050888
7005A25
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Open the door and undo the bolt.2. Recover the bracket.2050890
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Čeština
Dansk
Deutsch
Ελληνικά
English
English
Español
Suomi
Français
Français
עברית
Hrvatski
Magyar
Italiano
日本語
한국어
Nederlands
Polski
Português
Português
Română
Русский
Slovenčina
Slovenščina
Svenska
中文 (中国)
