Fiat PANDA 1.2 8v – CONNECT – – WIRING DIAGRAM, LOCATION COMPONENTS, OPERATIONAL DESCRIPTION – WIRING DIAGRAM, LOCATION COMPONENTS, OPERATIONAL DESCRIPTION

Wiring Diagram - CONNECT - Fiat PANDA 1.2 8v

CONNECT - WIRING DIAGRAM Fiat PANDA 1.2 8v

Tüm kablolama şemalarına erişin araba

COMPONENTS - CONNECT - Fiat PANDA 1.2 8v

Component code	Description	Reference to the assembly
B1	JUNCTION UNIT
B2	JUNCTION UNIT UNDER DASHBOARD
C20	PASSENGER SIDE DASHBOARD EARTH	-
C30	REAR LEFT EARTH	-
D20	FACIA/REAR JUNCTION	-
D30	REAR COUPLING FOR /FRONT DOOR. DRIVER''S SIDE	-
D31	RIGHT FRONT DOOR REAR COUPLING/.	-
D97	SHORT CIRCUITING COUPLING	-
D110	CLOCK SPRING AND STEERING WHEEL CONTROLS COUPLING	-
H1	IGNITION SWITCH
M1	BODY COMPUTER
M60	AIR BAG CONTROL UNIT
M94	RADIO RECEIVER NODE	-
P25	AERIAL POWER SUPPLY/AMPLIFIER
P26	MICROPHONE	-
P35	SPEAKER ON FRONT DOOR LEFT
P36	SPEAKER ON FRONT RIGHT DOOR
P40	SPEAKER IN REAR LEFT DOOR
P41	SPEAKER ON RIGHT REAR DOOR
P45	LEFT TWEETER SPEAKER	-
P46	RIGHT TWEETER SPEAKER	-
P75	CD PLAYER/CHANGER	-
P92	SUBWOOFER	-

Component location - CONNECT - Fiat PANDA 1.2 8v

CONNECT - COMPONENT LOCATION Fiat PANDA 1.2 8v

Tüm kablolama şemalarına erişin araba

COMPONENTS - CONNECT - Fiat PANDA 1.2 8v

Component code	Description	Reference to the assembly
B1	JUNCTION UNIT
B2	JUNCTION UNIT UNDER DASHBOARD
C20	PASSENGER SIDE DASHBOARD EARTH	-
C30	REAR LEFT EARTH	-
D20	FACIA/REAR JUNCTION	-
D30	REAR COUPLING FOR /FRONT DOOR. DRIVER''S SIDE	-
D31	RIGHT FRONT DOOR REAR COUPLING/.	-
D97	SHORT CIRCUITING COUPLING	-
D110	CLOCK SPRING AND STEERING WHEEL CONTROLS COUPLING	-
H1	IGNITION SWITCH
M1	BODY COMPUTER
M60	AIR BAG CONTROL UNIT
M94	RADIO RECEIVER NODE	-
P25	AERIAL POWER SUPPLY/AMPLIFIER
P26	MICROPHONE	-
P35	SPEAKER ON FRONT DOOR LEFT
P36	SPEAKER ON FRONT RIGHT DOOR
P40	SPEAKER IN REAR LEFT DOOR
P41	SPEAKER ON RIGHT REAR DOOR
P45	LEFT TWEETER SPEAKER	-
P46	RIGHT TWEETER SPEAKER	-
P75	CD PLAYER/CHANGER	-
P92	SUBWOOFER	-

The system modules or the modules to which the system can be connected for obtaining information or requesting services are different.The CONNECT is equipped with a CD ROM player that is able to read and manage CD ROMs and audio CDs. The audio supports may be regular commercial audio CDs or CD ROMs containing files in MP3 format (all levels) and an external CD Changer can be operated or an analogue audio output accepted.The system is also equipped with a GSM Dual Band module and micro format SIM Card reader (that allows the user the insert a SIM Card). There is an external microphone (hands-free and voice recognition usage).The CONNECT system may be activated in two different modes:Automatic activation with the ignition key ONManual activation by means of ON buttonEmergency manual activation by means of SOS buttonWhen the ignition key is turned to MAR position, the CONNECT system turns on automatically to make all the functions described in this chapter active or enabled.With the ignition key in STOP position, the CONNECT system comes on when the ON button is pressed to make the following modes available:MAINAUDIONAVTELSOS and SERVICE (Targasys)769In this mode, the SETUP and TRIP modules can be activated but it is not possible to validate any parameter change, language change or measurement unit change or any other type of adjustment envisaged by the CONNECT system. These limitations are normal when the system is activated by means of the ON button. When the vehicle is not running (key OFF), the data transmission devices inside the vehicle are not operational. When ignition key is turned ON, the system begins to work.The CONNECT system may be activated in two different modes:deactivation independent of the ignition keydeactivation dependent on the ignition keyTo choose the deactivation mode, see the Power OFF submenu in the SEPUP menu.When the OFF mode is activated, irrespective of the ignition key, the CONNECT system can be turned off by pressing the ON button.The display shows the message DEACTIVATION PROCEDURE IN PROGRESS, WAIT A FEW MOMENTS.769With the ignition key OFF, the system deactivates with a delay of 20 minutes if a system destination has been set or if a phone conversation is in progress.When the Off mode is activated, the CONNECT system may be turned off by turning the ignition key to the OFF position.The Connect (NIT) includes an ANTITHEFT function that prevents it operating in the case of theft.The NIT is installed during producition and connnected to the CAN network in order to establish communication with the Body Computer and store an antitheft code known as the Exchange Code.At each subsequent Key On (and even if the battery is disconnected), an automatic authentication procedure is repeated: if the outcome of the Exchange Code check is positive, the system starts working, whilst if the codes compared are not the same, a message appears on the display and on the actual radio Code Card767The Master Code is pre-programmed in production and different for each NIT. It is also different from the Exchange Code.768The procedure for entering the Master Code manually is only necessary if the Body Computer is replaced or a NIT already used on another vehicle with a CAN is installed.768A new NIT (never installed on other vehicles) may be fitted using an automatic authentication procedure without manual input of the Master Code.The phone module allows normal phone activity, text messages, support for Service Calls to the Provider (described in the relevant chapter) and Internet access by means of WAP (Wireless Access Protocol) and can be partly managed using the controls on the steering wheel.The CONNECT module sends various information to the control panel via the CAN network on phone section operating status.The navigation system allows you to reach a destination set by the user by giving visual and acoustic instructions.The navigation module built into the NIT receives data on progress (forward motion and reverse) and direction changes from information made available on the CAN network by the NBC. It cross-checks this with information received from GPS satellites by means of the GPS aerial on the car roof to calculate the Estimated Car Point (car location).767The navigation module does not contain a gyroscope because if no signals are received from the satelllites, the Navigation system recognises the car''s motion using vehicle motion information received from the CAN network.Upon initial activation and each time the battery is disconnected, the GPS takes about 15 minutes to activate.The navigation system takes about 100km to self-regulate accurately from the first system start-up and when the tyres are changed.If the engine is turned off and the vehicle is moved with the system off (e.g. on a pick-up truck), at the next key-on, the GPS system will take a few minutes to determine the car''s new position.The navigation CD-ROM drive is located on the front of the Connect system and is the same as used for audio CDs.It is not therefore possible to use the audio player and the navigation drive simultaneously: The navigation system can, however, work partly even without the navigation CD-ROM inserted.The main function of the Navigation module is called Route Guidance. This is responsible for extracting, managing and processing the information required to guide the user to the set destination.With the key ON, the Connect and Navigation system mobile are activated. A message appears reminding the customer that the navigation system is a tool that can help guide through traffic but the reponsibility always lies with the driver and the highway code must be respected at all times. When the control knob is pressed, the vehicle is the vehicle is located by the satellites and then the vehicle position co-ordinates are displayed as shown in the figure below.The Trip Computer module integral with the Connect manages and calculates a lot of information that can then be displayed on screen to supply a set of useful data on the route followed by the user.Some information comes directly from the Navigation module, others comes from the various vehicle Nodes. For this reason, the Trip computer is fully operational only when the the ignition is ON and the network wakes up and can carry information required by the Trip Computer.When the TRIP key is pressed, the TRIP COMPUTER module is activated and a screen appears with the following information:ARRIVAL TIMEDISTANCE FROM THE DESTINATIONSPEED LIMITRANGEINSTANTANEOUS FUEL CONSUMPTIONDISTANCE TRAVELLEDAVERAGE SPEEDAVERAGE FUEL CONSUMPTIONThe Trip module is able to calculate this data using information made available by other nodes on the CAN network.

Operational Description - CONNECT - Fiat PANDA 1.2 8v

The radio receiver node M094- From connector A:pin 4: receives an ignition-operated supply from the line protected by fuse F35; the power supply is distributed by the short circuit coupling D097E to the controls on the steering wheel (pin 5);pin 7: receives a direct battery power supply from the line protected by fuses F39 and F01;pin 8: connection to earth C020connector B;pin 6: receives the side lights on signal for managing the instrument lighting;pin 5: connection with the aerial P025;pin 1, 3: connection to the CAN [EL1050].767Earth C020 is secured to the passenger compartment floor and is positioned near the right front wheel arch (footwell area).- From connector B:pin 1, 2, 7, 8: connection with the rear speakers P040 and P041; for the Hi-Fi type system, the sub-woofer P092 is also connected to the same lines;pin 3, 4, 5, 6: connection to the front speakers P035 and P036; for the Hi-Fi system the front tweeters P045 and P046 are connected to the same lines;From connector C, it provides the power supply for the sub-woofer P092 located under the front passenger seat for the Hi-Fi system.- From connector D:pin 10, 11: it receives the signals coming from the controls on the steering wheel;pin 12, it provides the reference earth for the controls on the steering wheel.From connector E it interfaces with the CD cartridge P075 housed inside the glove compartment.The infotelematic node M065 receives the milometer signal at pin 11 supplied by the body computer M001.Pins 9 and 18 receive reference signals from the hands-free microphone P026 whilst pin 12 is earthed.The E-CALL function which activates a call to the emergency centre is activated from pin 5 of the infotelematic node.767Couplings D020 and D031 are housed, in the passenger compartment, in the lower part of the right front pillar, near the door cable loom, passenger side. Coupling D030 is housed, in the passenger compartment, in the lower part of the left front pillar, near the door cable loom, driver side.