TRANSMISSION – Chrysler Sebring LXi 1998 – SYSTEM WIRING DIAGRAMS

TRANSMISSION

Transmission Wiring Diagram (1 of 3) for Chrysler Sebring LXi 1998

List of elements for Transmission Wiring Diagram (1 of 3) for Chrysler Sebring LXi 1998:

• (eng harn, near tcm breakout)
• (eng harn, near turbine speed sensor breakout)
• 2-4 press sw
• 2-4 pressure switch
• 2-4 sol ctrl
• 2-4 solenoid
• A24
• A41
• Auto stick dn sw
• Body control module
• Ccd bus (+)
• Ccd bus (-)
• Controller anti-lock brake
• D21
• F11
• Fuse 11 10a
• Fused (b+)
• Fused ign out
• G102 (top of left front strut tower)
• Gnd
• Ground
• Hot in off, run or start
• Input spd sns sig
• Junction block
• K22
• K24
• Low/ reverse pressure switch
• Low/ reverse solenoid
• Low/rev press
• Low/rev sol. ctrl
• Od solenoid ctrl
• Output shaft speed sensor (on left side of transmission case)
• Output spd sns
• Over- drive solenoid
• Overdrive pressure switch
• Pnp sw sense
• S100
• S101
• S125
• S140
• S141
• Sci receive
• Sci transmit
• Sensor gnd
• Spd sensor gnd
• T10
• T13
• T14
• T15
• T16
• T19
• T20
• T41
• T42
• T44
• T47
• T50
• T52
• T54
• T59
• T60
• Torq mgmt req
• Tps sig
• Tr rng t42 sens
• Trans rly out
• Trans temp sig
• Transmission control module (on left front inner fender)
• Transmission solenoid & pressure switch assembly (transmission)
• Turbine speed sensor (on left side of torque converter housing)
• Ud solenoid ctrl
• Under- drive solenoid
• Vss sig
• Z13
• Z14

Transmission Wiring Diagram (2 of 3) for Chrysler Sebring LXi 1998

List of elements for Transmission Wiring Diagram (2 of 3) for Chrysler Sebring LXi 1998:

• (top of left front strut tower) g102
• Acc
• Automatic shutdown relay
• Autostick switch (integral with gearshift mechanism)
• Back-up lamp switch
• Engine starter motor relay, fuel pump relay
• Exterior lights system (back-up lamps)
• Fuse 3 20a
• Fuse 5 20a
• Fuse 8 20a
• G200 (left kick panel)
• Hall effect switches
• Hot at all times
• Ignition switch
• Junction block (under left side of dash)
• Lock
• Nol
• Off
• P3l
• Power distribution center
• Prnl
• Red
• Red/ tan
• Red/tan
• Run
• S101
• S102
• S104
• Start
• Trans temp sensor
• Transmission control relay
• Transmission range switch (in transmission, on top of valve body)

Transmission Wiring Diagram (3 of 3) for Chrysler Sebring LXi 1998

List of elements for Transmission Wiring Diagram (3 of 3) for Chrysler Sebring LXi 1998:

• (2.4l)
• (2.5l)
• (eng harn, 2.4l: near cam sensor breakout, 2.5l: near iac motor breakout)
• (eng harn, 2.4l: near map/iat sensor breakout, 2.5l: near egr breakout)
• (eng harn, 2.4l: near map/iat sensor breakout, 2.5l: near inj 6 breakout)
• (eng harn, in pcm breakout)
• (eng harn, internal to pdc)
• (eng harn, near ignition coil breakout)
• (eng harn, near pcm breakout) s120
• (eng harn, near pdc breakout)
• (top of left front strut tower)
• 2.4l
• 2.5l
• A14
• Battery temperature sensor
• Ccd bus (+)
• Ccd bus (-)
• Ckp sensor sig
• Column, bottom dash)
• Crankshaft position sensor
• D21
• Data link connector (left of steering
• Double start override
• Ect sensor sig
• Engine controls system
• Engine coolant temperature sensor (2.4l: on top left front of eng, 2.5l: near thermostat housing)
• Engine starter motor relay (in power distribution center)
• F12
• Fuel pump relay, controller anti-lock brake
• Fuse 10a
• Fuse 15a
• Fused b (+)
• G102
• Gnd
• Hot in run
• Hot in run & start
• Ign (run/start)
• Instrument cluster system
• Junction block
• K22
• K24
• K29
• K90
• P/n sw sense
• Power distribution center
• Powertrain control module (between air cleaner housing & power distribution center)
• Red/tan
• S101
• S105
• S110
• S115
• S116
• S117
• S121 (eng harn, in pcm breakout)
• S127
• S130 (eng harn, in pcm breakout)
• S132
• S133
• Sci transmit
• Sensor gnd
• Stop lamp switch (top of brake pedal)
• Stop lp sw sense
• T10
• T41
• Tan
• Throttle position sensor (on side of throttle body)
• Torque req sense
• Tp sens sig
• Vss signal
• Z12