WARNING SYSTEMS – Infiniti FX45 2008 – SYSTEM WIRING DIAGRAMS

WARNING SYSTEMS

Chime Wiring Diagram for Infiniti FX45 2008

List of elements for Chime Wiring Diagram for Infiniti FX45 2008:

74

• (behind instrument cluster) m45
• (on floor near driver seat) b15
• 15a
• 61a
• B14
• Bat (f/l)
• Bat (fuse)
• Batt
• Body control module (bcm) (behind left kick panel)
• Buzzer
• Can-h
• Can-l
• Comb sw in 1
• Comb sw in 2
• Comb sw in 3
• Comb sw in 4
• Comb sw in 5
• Comb sw out 1
• Comb sw out 2
• Comb sw out 3
• Comb sw out 4
• Comb sw out 5
• Combination meter
• Combination switch
• Computer data lines system
• Door ind
• Door sw (dr)
• Driver side front door switch
• Driver side front power seat
• Fuse 10a
• Fuse 15a
• Fuse block (j/b) (behind left kick panel)
• Fuse, fusible link & relay box (right rear of engine compt)
• Fusible link m 50a
• Gnd
• Gnd (power)
• Gnd (signal)
• Hot at all times
• Hot in on or start
• Ign sw
• Ignition knob switch
• Input1
• Input2
• Input3
• Input4
• Input5
• Inserted
• Intelligent key unit (if equipped) (behind left end of dash)
• Key sw
• Key switch
• Key switch & ignition knob switch (w/ intelligent key)
• M1 8a
• M45 (behind instrument cluster)
• M55
• M56
• Output1
• Output2
• Output3
• Output4
• Output5
• Pnk
• Push sw
• Pushed
• Red
• Removed
• Rx (comb meter)
• Seat belt buckle switch
• Seat belt ind
• Tx (comb meter)
• Unified meter & a/c amplifier (behind center console)
• Unified meter control unit
• W/ intelligent key
• W/o intelligent key
• Withdrawn

Lane Departure Warning Wiring Diagram for Infiniti FX45 2008

List of elements for Lane Departure Warning Wiring Diagram for Infiniti FX45 2008:

28

• (behind left kick panel)
• 5a m1
• Buzzer
• Can-h
• Can-l
• Combination meter
• Computer data lines system
• Fuse 10a
• Fuse block (j/b)
• Gnd
• Gnd can shd
• Gnd housing
• Gnd pcb
• Hot in on or start
• Ign
• Illum
• Ind
• Interior lights system
• Ldw camera unit (at top center of windshield)
• Ldw chime (behind center of dash)
• Ldw ind
• Ldw switch
• M45 (behind instrument cluster)
• Nca
• Red
• Signal
• Sw input
• Sys on ind

Tire Pressure Monitoring Wiring Diagram for Infiniti FX45 2008

List of elements for Tire Pressure Monitoring Wiring Diagram for Infiniti FX45 2008:

48

• (behind instrument cluster) m45
• 15a
• 5a m1
• Bat (f/l)
• Bat (fuse)
• Batt
• Body control module (bcm) (behind left kick panel)
• Buzzer
• Can-h
• Can-l
• Combination meter
• Computer data lines system
• Data link connector (lower left side of dash)
• Data out
• Display control unit (behind right side of dash)
• Exterior lights system
• Flsher output (left)
• Flsher output (right)
• Fuse & fusible link block (right rear of engine compartment)
• Fuse 10a
• Fuse 15a
• Fuse block (j/b) (behind left kick panel)
• Fusible link m 50a
• Gnd
• Gnd (power)
• Gnd (signal)
• Hot at all times
• Hot in on or start
• Ign
• Ign sw
• Kless tuner signal
• Kless tuner pwr sply
• M20
• M55
• M56
• Pnk
• Pwr sply
• Red
• Red
• Remote keyless entry receiver (behind right side of dash)
• Rx (comb meter)
• Sensor gnd
• Tire pressure ind
• Tire pressure warning check switch
• Tpms mode trg sw
• Tx (comb meter)
• Unified meter & a/c amplifier (behind center console)
• Unified meter control unit