ENGINE PERFORMANCE – Chrysler Sebring GTC 2004 – SYSTEM WIRING DIAGRAMS

ENGINE PERFORMANCE

2.4L

2.4L, Engine Performance Wiring Diagram (1 of 3) for Chrysler Sebring GTC 2004

List of elements for 2.4L, Engine Performance Wiring Diagram (1 of 3) for Chrysler Sebring GTC 2004:

• (behind catalytic converter) oxygen sensor 1/2 (downstream)
• (front of engine compt)
• (left front strut tower)
• (near breakout to ign coil)
• (near breakout to pcm)
• (on exhaust manifold) oxygen sensor 1/1 (upstream)
• 1/2 htr ctrl
• A/c clutch
• A/c system
• Asd relay
• Battery temp
• Brake sw
• C24
• C27
• C28
• Ckp sig
• Cmp sig
• Coil 1
• Coil 2
• Cooling fans system
• Cruise control system
• Ect sig
• Evap purge
• Evap/ purge solenoid (left side of engine compt)
• F142
• Fuel injectors
• Fuel pump rly
• G103
• G103 (left front strut tower)
• Gen field
• Generator
• Hi speed fan
• Iac motor
• Iac return
• Iat sig
• Ignition coil
• Injector 1
• Injector 2
• Injector 3
• Injector 4
• K106
• K107
• K108
• K11
• K12
• K13
• K14
• K141
• K17
• K19
• K199
• K20
• K21
• K22
• K24
• K25
• K29
• K31
• K41
• K42
• K44
• K45
• K51
• K52
• K60
• K610
• K90
• K902
• K99
• Knock sensor
• Ks return
• Ks sig
• Lo speed fan
• Map sig
• Natural vacuum leak detection assembly (on fuel tank)
• Noise suppressor
• Nvld sol
• Nvld switch
• O2 1/1 htr
• O2 1/1 sig
• O2 1/2 sig
• O2 return
• Powertrain control module (left front of engine compt)
• S/c switch
• S/c vacuum
• S/c vent
• S127
• S135
• S148
• S150
• Sensor grd
• Shift interlock system
• Starter rly
• Starting system
• Stop- light switch (top of brake pedal)
• Tan
• Tan/red
• Tp sig
• V32
• V35
• V36
• V37

2.4L, Engine Performance Wiring Diagram (2 of 3) for Chrysler Sebring GTC 2004

List of elements for 2.4L, Engine Performance Wiring Diagram (2 of 3) for Chrysler Sebring GTC 2004:

• (at left front kick panel)
• (convertible) (left front side of trunk)
• (in pdc) s108
• (near breakout for camshaft position sensor)
• (on left kick panel) data link connector
• (on side of throttle body) idle air control motor
• A/c pressure transducer (top of a/c compressor)
• Ambient temperature sensor (rear side of front bumper beam)
• Automatic shut down relay (in power distribution center)
• Body control module (on junction block, left end of dash)
• Camshaft position sensor (rear of cylinder head)
• Crankshaft position sensor (right front of engine block)
• Engine coolant temperature sensor (top left front of engine)
• Fuel lev sens sig
• Fuel pump module (on fuel tank)
• Fuel pump relay (in power distribution center)
• Fuse 20a
• Fuse 30a
• G302 g300 (sedan) (center of trunk opening)
• Hot at all times
• Hot in run or start
• Instrument cluster
• Intake air temperature sensor (on intake manifold)
• Manifold absolute pressure sensor (on intake manifold plenum)
• Mil driver
• Pci bus
• Pnk
• Power distribution center (left side of engine compt)
• Red
• Red/ tan
• Red/tan
• S102
• S104
• S105
• S115 (near breakout for map/iat)
• S116 (near breakout for a/c compressor)
• S117
• S120
• S326
• Sci receive
• Service engine soon
• Tach control
• Tachometer
• Throttle position sensor (on throttle body)

2.4L, Engine Performance Wiring Diagram (3 of 3) for Chrysler Sebring GTC 2004

List of elements for 2.4L, Engine Performance Wiring Diagram (3 of 3) for Chrysler Sebring GTC 2004:

• (left front of engine compt) s111
• (left side of transmission)
• (near left front strut tower) g103
• 2-4 press
• 2-4 sol
• A/c pres sig
• A14
• A41
• Acc
• Air pump motor (below intake manifold)
• Air pump motor relay (below intake manifold)
• Air pump mtr rly ctrl
• Backup switch
• C18
• D15
• D20
• D21
• D25
• Exterior lights system
• F11
• F12
• Fuse 10a
• Fuse 20a
• Fuse 40a
• Fused b+
• Fused ign sw
• G108 (near left headlight)
• Ground
• Hot at all times
• Hot off, run or start
• Ignition
• Ignition switch
• Input speed sensor (on transmission, left of shift lever)
• Iss sig
• Junction block (left end of dash)
• K62
• K904
• Low/rev press
• Low/rev sol
• Nol
• O2 rtn down
• Od press sw
• Off
• Oss sig
• Output speed sensor (left side of trans- mission)
• Overdrive sol
• P3l
• Pci bus
• Pnk
• Power distribution center (left side of engine compt)
• Powertrain control module (left front of engine compt)
• Prnl
• Red
• Red/tan
• Run
• S100
• S123
• S125
• S160
• Sci receive
• Sci transmit
• Ss ground
• Start
• T13
• T14
• T15
• T16
• T19
• T20
• T41
• T42
• T47
• T50
• T52
• T54
• T59
• T60
• Tan
• Trans relay
• Trans temp
• Trans temp sensor
• Transmission control relay (in power distribution center)
• Transmission range sensor (on trans- mission)
• Transmission solenoid & pressure switches (left side of trans- mission)
• Trs t1
• Trs t3
• Trs t41
• Trs t42
• Underdrive sol
• Unlock
• Z12
• Z13
• Z14

2.7L

2.7L, Engine Performance Wiring Diagram, Early Production (1 of 3) for Chrysler Sebring GTC 2004

List of elements for 2.7L, Engine Performance Wiring Diagram, Early Production (1 of 3) for Chrysler Sebring GTC 2004:

• (eng harn, near break- out for gen- erator feed)
• (eng harn, near breakout for cmp sensor)
• (eng harn, near breakout for knock sensor)
• (eng harn, near breakout for left bank down ho2s)
• (eng harn, near breakout for left bank up ho2s) s118
• (eng harn, near breakout for right bank up ho2s)
• (in left fuel rail harn)
• (near left strut tower) g103
• A142
• Asd rly output
• Automatic shutdown relay
• Ckp sensor signal
• Cmp sensor signal
• Coil on plug drv 1
• Coil on plug drv 2
• Coil on plug drv 3
• Coil on plug drv 4
• Coil on plug drv 5
• Coil on plug drv 6
• Coils on plug
• Ect sensor signal
• F12
• Fuel injectors
• Fuse 20a
• Fuse 30a
• Fused ign sw out
• G103 (near left strut tower)
• Gen field driver
• Generator
• Gnd
• Heated oxygen sensor (ho2s) (left bank up) (on left exhaust manifold)
• Heated oxygen sensor (ho2s) (right bank up) (on right exhaust manifold)
• Heated oxygen sensor (left bank down) (on left exhaust pipe, behind catalytic converter)
• Heated oxygen sensor (right bank down) (on right exhaust pipe, behind catalytic converter)
• Ho2s ground
• Hot at all times
• Iat sensor signal
• Inj 1 driver inj 6 driver
• Inj 2 driver
• Inj 3 driver
• Inj 4 driver
• Inj 5 driver
• K11
• K12
• K127
• K13
• K14
• K20
• K21
• K22
• K24
• K241
• K38
• K41
• K42
• K44
• K58
• K90
• K91
• K92
• K93
• K94
• K95
• K96
• Knock sensor signal
• Left bank up ho2s
• Map sensor signal
• Nca
• Pcv heater
• Power distribution center (on left front inner fender)
• Powertrain control module (left front of engine compt)
• Red/tan
• Right bank up ho2s
• S104
• S108 (eng harn, internal to pdc)
• S134
• S137
• S139
• S143
• S149
• Sc on/off sw
• Start motor rly ctrl
• Starting/ charging system
• Tan
• Tan/pnk
• Tan/red
• Tp sensor signal
• V32
• Z108

2.7L, Engine Performance Wiring Diagram, Early Production (2 of 3) for Chrysler Sebring GTC 2004

List of elements for 2.7L, Engine Performance Wiring Diagram, Early Production (2 of 3) for Chrysler Sebring GTC 2004:

• (eng harn, left side of eng compt)
• (eng harn, near break- out for a/c compressor clutch)
• (eng harn, near breakout for cmp sensor)
• (next to coolant fill neck) engine coolant temperature sensor
• (on a/c compressor discharge line) a/c pressure transducer
• (on rear side of front bumper beam) ambient temperature sensor
• (on side of throttle body) idle air control motor
• A/c pressure
• Camshaft position sensor (on front of engine, at cyl head)
• Crankshaft position sensor (on left front side of engine block)
• Iac mtr 1
• Iac mtr 2
• Iac mtr 3
• Iac mtr 4
• Intake air temperature sensor (on air induction boot)
• Knock sensor
• Manifold absolute pressure sensor (on right front of intake manifold)
• Noise suppressor
• Red/tan
• S110
• S117 (eng harn, near break- out for cmp sensor)
• S121 (eng harn, near breakout for pcm)
• S124
• S155 (eng harn, near break- out for cmp sensor)
• S156
• Sensor gnd
• Signal
• Throttle position sensor (on side of throttle body)
• Transmission control module

2.7L, Engine Performance Wiring Diagram, Early Production (3 of 3) for Chrysler Sebring GTC 2004

List of elements for 2.7L, Engine Performance Wiring Diagram, Early Production (3 of 3) for Chrysler Sebring GTC 2004:

• (convertible)
• (near left strut tower) g103
• (sedan)
• A/c comp rly ctrl
• A/c press signal
• A/c system
• A/t
• A14
• Amb temp sen signal
• Anti-lock brake controller (lower left front of engine compt)
• Asd rly ctrl
• Body control module
• Brake lamp sw sense
• Brake lamp switch (top of brake pedal)
• Brake sw sense
• Brake transmission shift interlock solenoid
• C18
• C24
• C27
• C28
• Cooling fans system
• Cruise control system
• D20
• D21
• D25
• Data link connector (on left kick panel, above hood release)
• Eatx rmp signal
• Evap sol sense
• Evap/prge sol ctrl
• Evaporative purge solenoid (on left side of engine compt)
• Fuel level sensor
• Fuel lvl sensor sig
• Fuel pmp rly ctrl
• Fuel pump module (on top of fuel tank)
• Fuel pump motor
• Fuel pump relay
• Fuse 23 20a
• Fuse 8 20a
• Fused b (+)
• G300 (center of trunk opening, below latch)
• G302 (left front of trunk)
• Gnd
• Gnd
• High spd rly ctrl
• Hot at all times
• Hot in run or start
• Iac driver 1
• Iac driver 2
• Iac driver 3
• Iac driver 4
• Instrument cluster
• Junction block (left end of dash)
• K106
• K107
• K108
• K141
• K25
• K29
• K31
• K341
• K39
• K40
• K51
• K52
• K59
• K60
• K71
• Leak pmp sol ctrl
• Leak pmp sw sense
• Left bank down ho2s
• Low spd rly ctrl
• M/t
• Malfunction ind (chk eng lp ctrl)
• Malfunction indicator lamp (check engine)
• Pci bus
• Pnk
• Power distribution center (on left front inner fender)
• Powertrain control module (left front of engine compt)
• Red
• Red/tan
• Right bank down ho2s
• S102
• S105
• Sci receive
• Sci transmit
• Sensor gnd
• Speed control on/off sw sense
• Speed ctrl vent sol
• Speed ctrl vac sol
• Speed strl sw signal
• T10
• T41
• Tan/red
• Torque req sense
• Transmission control module (left front of engine compt)
• Transmission range sensor (on lower left side of transmission)
• Trs t41 sen
• Trs t41 sense
• V35
• V36
• V37
• Vapor canister leak detection pump (top of fuel tank, near evap canister)
• Vehicle speed control servo (on left strut tower)
• Vss sig
• Vss signal
• Z107
• Z109

2.7L, Engine Performance Wiring Diagram, Late Production (1 of 4) for Chrysler Sebring GTC 2004

List of elements for 2.7L, Engine Performance Wiring Diagram, Late Production (1 of 4) for Chrysler Sebring GTC 2004:

• (front of engine compt) s127
• (near breakout for generator feed) s149
• (near breakout for oxygen sensor 1/1 right bank up) s138
• 1/2 htr ctrl
• 2/1 htr ctrl
• 2/2 htr ctrl
• A/c clutch
• A/c system
• Asd relay
• Battery temp
• Brake sw
• C24
• C27
• C28
• Ckp sig
• Cmp sig
• Coil 1 cntrl
• Coil 2 cntrl
• Coil 3 cntrl
• Coil 4 cntrl
• Coil 5 cntrl
• Coil 6 cntrl
• Cooling fans system
• Cruise control system
• Ect sig
• Egr sens sig
• Egr sol cntrl
• Evap purge
• Evap/ purge solenoid (left side of engine compt)
• F142
• Fuel pump rly
• G103 (left front strut tower)
• Gen field
• Generator
• Hi speed fan
• Iac motor
• Iac return
• Iat sig
• Inj 1 cntrl
• Inj 2 cntrl
• Inj 3 cntrl
• Inj 4 cntrl
• Inj 5 cntrl
• Inj 6 cntrl
• K106
• K107
• K108
• K11
• K12
• K13
• K14
• K199
• K20
• K21
• K22
• K235
• K24
• K241
• K25
• K29
• K299
• K31
• K35
• K38
• K39
• K399
• K41
• K42
• K44
• K45
• K51
• K52
• K58
• K60
• K90
• K902
• K91
• K92
• K93
• K94
• K95
• K96
• K99
• Ks return
• Ks sig
• Lo speed fan
• Map sig
• Natural vacuum leak detection assembly (on fuel tank)
• Nvld sol
• Nvld switch
• O2 1/1 htr
• O2 1/1 sig
• O2 2/1 sig
• O2 return up
• Oxygen sensor 1/1 (right bank up) (at right front of engine)
• Oxygen sensor 1/2 (right bank down) (at rear of engine)
• Oxygen sensor 2/1 (left bank up) (at left front of engine)
• Oxygen sensor 2/2 (left bank down) (at right side of engine)
• Powertrain control module (left front of engine compt)
• S/c switch
• S/c vacuum
• S/c vent
• S140 (at front corner of left cylinder head)
• Sensor grd
• Starter rly
• Starting system
• Tan
• Tan/pnk
• Tan/red
• Tp sig
• V32
• V35
• V36
• V37

2.7L, Engine Performance Wiring Diagram, Late Production (2 of 4) for Chrysler Sebring GTC 2004

List of elements for 2.7L, Engine Performance Wiring Diagram, Late Production (2 of 4) for Chrysler Sebring GTC 2004:

• (on left fuel rail) s143
• Ambient temperature sensor (rear side of front bumper beam)
• Brake lamp switch (top of brake pedal)
• Coil on plugs
• Egr solenoid (left rear of engine)
• Fuel injectors
• G103 (left front strut tower)
• Knock sensor (below throttle body)
• Noise suppressor
• S137 (in engine valley, near left cylinder head)
• S139 (near breakout for knock sensor)
• S149
• Shift interlock system
• Tan
• Tan/pnk
• Tan/red

2.7L, Engine Performance Wiring Diagram, Late Production (3 of 4) for Chrysler Sebring GTC 2004

List of elements for 2.7L, Engine Performance Wiring Diagram, Late Production (3 of 4) for Chrysler Sebring GTC 2004:

• (convertible) (left front side of trunk)
• (left kick panel)
• (on left kick panel) data link connector
• (on side of throttle body)
• A/c pressure transducer (on a/c compressor discharge line)
• Automatic shut down relay (in power distribution center)
• Body control module (left kick panel)
• Camshaft position sensor (on front of engine, at cylinder head)
• Crankshaft position sensor (on left front side of engine block)
• Engine coolant temperature sensor (at front of engine, next to coolant fill neck)
• Fuel lev sens sig
• Fuel pump module (on fuel tank)
• Fuel pump relay (in power distribution center)
• Fuse 20a
• Fuse 30a
• G302 g300 (sedan) (center of trunk opening)
• Hot at all times
• Hot in run or start
• Idle air control motor
• Inlet air temperature sensor (on air induction boot)
• Instrument cluster
• Manifold absolute pressure sensor (on right front of intake manifold)
• Mil driver
• Pci bus
• Pnk
• Power distribution center (left side of engine compt)
• Red
• Red/ tan
• Red/tan
• S102
• S104
• S105
• S108 (in pdc)
• S117 (near breakout for throttle position sensor)
• S120
• S156 (near breakout for a/c compressor clutch)
• S326
• Sci receive
• Service engine soon
• Tach control
• Tachometer
• Throttle position sensor (on throttle body)

2.7L, Engine Performance Wiring Diagram, Late Production (4 of 4) for Chrysler Sebring GTC 2004

List of elements for 2.7L, Engine Performance Wiring Diagram, Late Production (4 of 4) for Chrysler Sebring GTC 2004:

• (left front engine compt) s100
• (left front of engine compt) s111
• (near left front strut tower) g103
• (near output speed sensor)
• 2-4 press
• 2-4 sol
• A/c pres sig
• A14
• A41
• Acc
• Backup switch
• C18
• D15
• D20
• D21
• D25
• Exterior lights system
• F11
• F12
• Fuse 10a
• Fuse 20a
• Fused b+
• Fused ign sw
• G108 (near left headlight)
• Ground
• Hot at all times
• Hot off, run or start
• Ignition
• Ignition switch
• Input speed sensor (left side of transaxle)
• Iss sig
• Junction block (left end of dash)
• K141
• K341
• K904
• Low/rev press
• Low/rev sol
• Nol
• O2 1/2 sig
• O2 2/2 sig
• O2 rtn down
• Od press sw
• Off
• Oss sig
• Output speed sensor (left side of transaxle case)
• Overdrive sol
• P3l
• Pci bus
• Pnk
• Power distribution center (left side of engine compt)
• Powertrain control module (left front of engine compt)
• Prnl
• Red
• Red/tan
• Run
• S123
• S125
• Sci receive
• Sci transmit
• Ss ground
• Start
• T13
• T14
• T15
• T16
• T19
• T20
• T41
• T42
• T47
• T50
• T52
• T54
• T59
• T60
• Trans relay
• Trans temp
• Trans temp sensor
• Transmission control relay (in power distribution center)
• Transmission range sensor (lower left side of transaxle)
• Transmission solenoid/ pressure switches (left side of transaxle)
• Trs t1
• Trs t3
• Trs t41
• Trs t42
• Underdrive sol
• Unlock
• Z12
• Z13
• Z14