All Wiring Diagrams for Chevrolet S10 Pickup 1996

AIR CONDITIONING

2.2L

2.2L (VIN 4), A/C Wiring Diagram for Chevrolet S10 Pickup 1996

List of elements for 2.2L (VIN 4), A/C Wiring Diagram for Chevrolet S10 Pickup 1996:

• +5v
• A tan
• A/c clutch diode
• A/c comp fuse 14 10a
• A/c compressor clutch
• A/c compressor clutch relay (engine compartment, left side of cowl)
• A/c on input
• A/c pressure
• A/c refrigerant pressure sensor
• Bi-lv
• Blend
• Blower motor
• Blower motor relay (right rear of engine compt)
• Blower resistors (right rear of engine compartment)
• Blower switch
• C 1995 vftc
• Clutch control
• Def
• G114 (rear of left cylinder head)
• G117 (rear of right cylinder head)
• Gauges fuse 4 20a
• Ground
• Hot at all times
• Hot in run
• Hot in run, bulb test or start
• Htr
• Htr a/c fuse 6 25a
• Hvac control assembly
• I/p fuse block
• Max
• Mode switch
• Nca
• Norm
• Off
• Pnk
• Powertrain control module (behind right side of i/p)
• Red
• Solid state
• Tan
• Temperature selector
• Temperature valve motor (right side of bulkhead)
• Vent

Heater Wiring Diagram for Chevrolet S10 Pickup 1996

List of elements for Heater Wiring Diagram for Chevrolet S10 Pickup 1996:

• A tan
• Blower motor
• Blower motor relay (right rear of engine compt)
• Blower resistors (right rear of engine compartment)
• Blower switch
• C 1995 vftc
• Def
• G114 (rear of left cylinder head)
• Hot at all times
• Hot in run
• Htr
• Htr a/c fuse 6 25a
• Hvac control assembly
• I/p fuse block
• Mode switch
• Off
• Red
• Solid state
• Tan
• Temperature selector
• Temperature valve motor (right side of bulkhead)
• Vent

4.3L

4.3L (VIN W), A/C Wiring Diagram for Chevrolet S10 Pickup 1996

List of elements for 4.3L (VIN W), A/C Wiring Diagram for Chevrolet S10 Pickup 1996:

• (rear of compressor)
• (right rear of engine compartment)
• A tan
• A/c clutch diode
• A/c comp fuse 14 10a
• A/c compressor clutch
• A/c compressor clutch relay (center rear of engine compartment)
• A/c high pressure cutout switch
• A/c low pressure cutout switch
• A/c on input
• Bi-lv
• Blend
• Blower motor
• Blower motor relay (right rear of engine compartment)
• Blower resistors (right rear of engine compartment)
• Blower switch
• C 1995 vftc
• Clutch control
• Def
• G114 (left side of engine, below exhaust manifold)
• G114 (rear of left cylinder head)
• Gauges fuse 4 20a
• Hot at all times
• Hot in run
• Hot in run, bulb test or start
• Htr
• Htr a/c fuse 6 25a
• Hvac control assembly
• I/p fuse block
• Max
• Mode switch
• Nca
• Norm
• Off
• Pnk
• Red
• Solid state
• Tan
• Temperature selector
• Temperature valve motor (right side of bulkhead)
• Vehicle control module (right side of engine compartment)
• Vent

Heater Wiring Diagram for Chevrolet S10 Pickup 1996

List of elements for Heater Wiring Diagram for Chevrolet S10 Pickup 1996:

• A tan
• Blower motor
• Blower motor relay (right rear of engine compt)
• Blower resistors (right rear of engine compartment)
• Blower switch
• C 1995 vftc
• Def
• G114 (rear of left cylinder head)
• Hot at all times
• Hot in run
• Htr
• Htr a/c fuse 6 25a
• Hvac control assembly
• I/p fuse block
• Mode switch
• Off
• Red
• Solid state
• Tan
• Temperature selector
• Temperature valve motor (right side of bulkhead)
• Vent

ANTI-LOCK BRAKES

2.2L

2.2L (VIN 4), Anti-lock Brake Wiring Diagrams for Chevrolet S10 Pickup 1996

List of elements for 2.2L (VIN 4), Anti-lock Brake Wiring Diagrams for Chevrolet S10 Pickup 1996:

• (left radiator support)
• Abs ind
• Abs lamp control
• Brake fuse 10a
• Brake ind
• Brake lamp control
• Brake pressure modulator valve (left rear of engine compt)
• Brake pressure warning switch
• Brake sw input
• Brake sw output
• Data link connector (left side of i/p)
• Diode module (above steering column)
• Ebcm ground
• G108
• Gauge fuse 10a
• Ground
• Hot at all times
• Hot in run
• Hot in run, bulb test or start
• I/p fuse block
• Ign
• Instrument cluster
• Left front wheel speed sensor
• Lft frt sensor (+)
• Lft frt sensor (-)
• Pnk
• Powertrain control module (right side of engine compt)
• Pump motor power
• Red
• Right front wheel speed sensor
• Rt frt sensor (+)
• Rt frt sensor (-)
• Serial data line
• Tan
• Vehicle speed sensor (left side of transmission)
• Vehicle speed sig
• Vss (+)
• Vss (-)
• Vss input

4.3L

4.3L (VIN W), Anti-lock Brake Wiring Diagrams for Chevrolet S10 Pickup 1996

List of elements for 4.3L (VIN W), Anti-lock Brake Wiring Diagrams for Chevrolet S10 Pickup 1996:

• Abs enable rly out
• Abs voltage
• Anti- lock ind
• Antilock lamp
• Bat
• Brake fuse 12 10a
• Brake ind
• Brake lamp
• Brake pressure modulator valve (left rear of engine compartment)
• Brake pressure sw
• Brake pressure warning switch (brake master cylinder)
• Brake switch sig
• Cruise control system
• Diode module (above steering column)
• Front axle switch
• Front axle switch (right of differential)
• G108 (left radiator support)
• Gauges fuse 4 10a
• Grd
• Hot at all times
• Hot in run
• Hot in run, bulb test or start
• I/p fuse block
• Ign
• Ign feed
• Instrument cluster
• Left front wheel speed sensor
• Lf iso solenoid
• Lf pwm solenoid
• Lf wheel speed-hi
• Lf wheel speed-lo
• Lft frt isolation sol fd
• Lft frt pwm sol feed
• Nca
• Pnk
• Pump driver
• Pump feedback
• Pump motor feed
• Pump motor relay
• Pump motor sens (+)
• Pump motor sens (-)
• Rear iso solenoid
• Rear isolation sol feed
• Rear pwm sol feed
• Rear pwm solenoid
• Red
• Rf iso solenoid
• Rf pwm solenoid
• Rf wheel speed-hi
• Rf wheel speed-lo
• Right front wheel speed sensor
• Rt frt isolation sol fd
• Rt frt pwm sol feed
• Tan
• Tcc/stoplamp switch (brake pedal bracket)
• Vehicle control module (right side of engine compartment)
• Vehicle speed sensor (left side of trans or rear of transfer case)
• Vss signal-hi
• Vss signal-lo

COMPUTER DATA LINES

2.2L

2.2L (VIN 4), Computer Data Lines for Chevrolet S10 Pickup 1996

List of elements for 2.2L (VIN 4), Computer Data Lines for Chevrolet S10 Pickup 1996:

• B11
• Brake pressure modulator valve (left rear of engine compt)
• Data clss 2
• Data link connector (below left side of i/p)
• Diagnostic energy reserve module (right kick panel)
• Dlc control
• G115 (rear of cylinder head)
• Hot at all times
• I/p fuse block
• Powertrain control module (right side of engine compt)
• Prog enable
• Pwr aux fuse 7 25a
• Remote keyless entry module (lower left side of i/p)
• Tan
• Uart data

4.3L

4.3L (VIN W), Computer Data Lines for Chevrolet S10 Pickup 1996

List of elements for 4.3L (VIN W), Computer Data Lines for Chevrolet S10 Pickup 1996:

• (pickup) g114 (rear of left cylinder head)
• B11
• Data clss 2
• Data link connector (below left side of i/p)
• Diag
• Diagnostic energy reserve module (behind right kick panel)
• Driver information display center (bravada only) (overhead console)
• G117 (utility) (rear of right cylinder head)
• Hot at all times
• I/p fuse block
• Prog enable
• Pwr aux fuse 7 25a
• Remote keyless entry module (lower left side of i/p)
• Tan
• Transfer case control module (behind center of i/p)
• Uart data
• Vehicle control module (right side of engine compt)

CRUISE CONTROL

Cruise Control Wiring Diagram for Chevrolet S10 Pickup 1996

List of elements for Cruise Control Wiring Diagram for Chevrolet S10 Pickup 1996:

• (2.2l vin 4)
• (4.3l vin w)
• (left rear of engine compt)
• (right side of engine compt)
• 2.2l vin 4
• 4.3l vin w
• 4000 pulses/mile
• A/t
• A12
• A13
• A14
• A15
• Brake fuse 12 10a
• Clutch pedal position switch (clutch pedal
• Cruise control module
• Cruise on input
• Cruise status
• Disengage input
• G114 (rear of left cylinder head)
• Ground
• Hot in run
• Hot in run, bulb
• I/p fuse block
• Ignition
• M/t
• Nca
• Off
• Powertrain control module (2.2l vin 4)
• R/a
• Resume/accel input
• Set sw
• Set/coast input
• Stop/haz fuse 1 20a
• Support)
• Tcc stoplamp switch (brake pedal support)
• Test or start
• Turn signal switch
• Vehicle control module (4.3l vin w)
• Vehicle speed input
• Vehicle speed sensor (vss)
• Vss return
• Vss signal

ENGINE PERFORMANCE

2.2L

2.2L (VIN 4), Engine Performance Wiring Diagrams (1 of 3) for Chevrolet S10 Pickup 1996

List of elements for 2.2L (VIN 4), Engine Performance Wiring Diagrams (1 of 3) for Chevrolet S10 Pickup 1996:

• (under left side of i/p) data link connector
• 5v ref voltage
• A/c refrig press sens
• A/c switch out
• Air conditioning system
• Anti-lock brakes system
• Cam pos sensor in
• Cam/crank sens grd
• Cam/crank sens pwr
• Camshaft position sensor (right side of engine)
• Class 2 data line
• Crank pos sensor in
• Crankshaft position sensor (right side of engine near coil pack assy)
• Cruise control system
• Cruise on signal in
• Ecm batt fuse 9 20a
• Ecm ign fuse 10 20a
• Ect sensor in
• Fuel gauge sens in
• Fuel inj 1 ctrl
• Fuel inj 2 ctrl
• Fuel inj 3 ctrl
• Fuel inj 4 ctrl
• Fuel injectors
• Fuel pump relay ctrl
• Fuse block
• G112 (left side of engine)
• G114 (left rear of cylinder head)
• H02s 2 signal in
• Ho2s 2 signal return
• Hot at all times
• Hot in run, bulb test or start
• Iac motor control
• Iat sens in
• Idle air control (iac) valve (on side of throttle assembly)
• Linear egr pos sens in
• Linear egr sol out
• Map sensor in
• O2s 1 signal in
• O2s 1 signal return
• Park/neutral position switch (left side of transmission)
• Pcm ground
• Pnk
• Power (battery)
• Power (ignition 1)
• Power (ignition)
• Powertrain control module (right front corner of engine compartment)
• Red
• Sensor return
• Tan
• Tp sensor in
• Trans pos sens in
• Trans press sens in
• Trans press sw in
• Trans temp sens in

2.2L (VIN 4), Engine Performance Wiring Diagrams (2 of 3) for Chevrolet S10 Pickup 1996

List of elements for 2.2L (VIN 4), Engine Performance Wiring Diagrams (2 of 3) for Chevrolet S10 Pickup 1996:

• A/c sensor (right side of engine compt)
• Engine coolant temperature (ect) sensor (front of engine)
• Engine fuse 15 20a
• Evaporative emissions canister purge solenoid valve (left rear frame rail)
• Evaporative emissions canister vent solenoid valve (crossmember, rear of fuel tank)
• Fuel tank vacuum sensor (front of fuel tank)
• Fuse block
• G114 (left rear of cylinder head)
• Gauges fuse 4 20a
• Hot in run
• Hot in run, bulb test or start
• Intake air temperature (iat) sensor (intake air ductwork)
• Linear exhaust gas recirc- ulation valve (top rear of engine)
• Manifold absolute pressure sensor (top of intake manifold)
• Nca
• Pnk
• Post converter oxygen sensor (behind catalytic converter)
• Pre convert- er oxygen sensor (left side of engine, in manifold)
• Red
• Tan
• Throttle position sensor (tps) (on side of throttle body)
• Trans fuse 24 10a
• Vehicle speed sensor (side of transmission)

2.2L (VIN 4), Engine Performance Wiring Diagrams (3 of 3) for Chevrolet S10 Pickup 1996

List of elements for 2.2L (VIN 4), Engine Performance Wiring Diagrams (3 of 3) for Chevrolet S10 Pickup 1996:

• (right side of engine) distributorless ignition control module
• 1-2 shift sol
• 2-3 shift sol
• 3-2 shift sol
• 3-2 shift sol ctrl
• A/c comp relay ctrl
• A/t
• Air conditioning system
• Anti-lock brakes system
• Automatic transaxle
• Brake fuse 12 20a
• Brake pedal sw in
• Canister purge sol ctrl
• Canister vent sol ctrl
• Cruise control system
• Fuel level
• Fuel pump & sender (fuel tank unit)
• Fuel pump oil pressure switch (right side of engine)
• Fuel pump prime connector
• Fuel pump relay (i/p relay center)
• Fuel tank press in
• G112 (left side of engine block)
• G112 (left side of engine)
• G114 (left rear of cylinder head)
• G415 (left rear frame rail)
• Hot in run
• I/p fuse block
• Ignition amplifier and switching module
• Ignition coil ctrl out
• Instrument cluster
• Knock sensor (side of engine block)
• Knock sensor in
• M/t
• Mil indic ctrl
• Nca
• Pcm ground
• Pcs hi
• Pcs lo
• Plugs spark
• Pnk
• Power (ignition 1)
• Powertrain control module (right front corner of engine compartment)
• Pressure switch manifold
• Red
• Sensor ground
• Service engine soon indic
• Shift sol a ctrl
• Shift sol b ctrl
• Solenoid power
• Tach input
• Tach signal out
• Tcc on signal
• Tcc on/off sol
• Tcc pwm sig out
• Tcc pwm signal
• Tcc/stop lamp switch (under left side of i/p)
• Trans force mtr feed
• Trans force mtr retrn
• Trans temp out
• Upshift indic (m/t only)
• Vss input
• Vss out
• Vss sensor in
• Vss sensor return

4.3L

4.3L (VIN W), Engine Performance Wiring Diagrams (1 of 4) for Chevrolet S10 Pickup 1996

List of elements for 4.3L (VIN W), Engine Performance Wiring Diagrams (1 of 4) for Chevrolet S10 Pickup 1996:

• (a/t)
• (m/t)
• 1-2 shift sol. ctrl
• 2-3 shift sol. ctrl
• 3-2 ctrl sol. ctrl
• A/c comp rly ctrl
• A/c compressor clutch relay (center rear of engine compartment)
• Anti-lock brake system (left front wheel speed sensor)
• Anti-lock brakes system (right front wheel speed sensor)
• Cam posit sens rtn
• Cam posit sens sig
• Camshaft position sensor (located within high voltage switch) (in distributor)
• Canister vent val sol
• Coil
• Crank posit sens ground
• Crank posit sens signal
• Crankshaft position sensor (lower right front of engine)
• Ect sens input
• Egr pintle posit input
• Evap emiss purge ctrl
• Evaporative emissions canister purge solenoid (evap) (top right center of engine)
• Evaporative emissions canister vent valve solenoid (if equipped)
• Fuel level input
• G114 (rear of left cylinder head)
• Hall effect sensor
• Iat temp sens sig
• Idle air control motor (top left side of engine)
• Idle air ctrl (iac) a hi
• Idle air ctrl (iac) a lo
• Idle air ctrl (iac) b hi
• Idle air ctrl (iac) b lo
• Ignition feed
• Inj no.1 ctrl
• Inj no.2 ctrl
• Inj no.3 ctrl
• Inj no.4 ctrl
• Inj no.5 ctrl
• Inj no.6 ctrl
• Knock sens sig
• Knock sensor (top rear of engine)
• Left bnk o2 sens hi
• Left bnk o2 sens lo
• Left front sens high
• Left front sens low
• Left oxygen sensor (in left exhaust pipe)
• Map sens input
• Mass air flow input
• Nca
• Pnk
• Pnk a
• Pnk c
• Post-ctlyst o2 sens hi
• Post-ctylst o2 sens lo
• Pre-converter oxygen sensor (forward of catalytic converter)
• Pre-ctlyst o2 sens hi
• Pre-ctlyst o2 sens lo
• Pump driver
• Pump motor relay
• Right bnk o2 sens hi
• Right bnk o2 sens lo
• Right front sens high
• Right front sens low
• Right oxygen sensor (right rear of engine in exhaust pipe)
• Sensor ground
• Tan
• Tcc on/off sol. ctrl
• Tcc pwm sol ctrl
• Tft sig
• Throttle posit sens
• Vehicle control module (vcm) (right side of engine compartment)
• Vehicle speed sensor (vss) (rear of transfer case) (a/t & 4wd) (left side of transmission) (m/t)
• Vss (hi)
• Vss (lo)

4.3L (VIN W), Engine Performance Wiring Diagrams (2 of 4) for Chevrolet S10 Pickup 1996

List of elements for 4.3L (VIN W), Engine Performance Wiring Diagrams (2 of 4) for Chevrolet S10 Pickup 1996:

• 1-2 shift sol.
• 2-3 shift sol.
• 3-2 control sol.
• Automatic transmission
• Ecm/ign fuse 10 20a
• Eng fuse 5 20a
• Fuel inj. no.1
• Fuel inj. no.2
• Fuel inj. no.3
• Fuel inj. no.4
• Fuel inj. no.5
• Fuel inj. no.6
• Hot in run, bulb test, or start
• I/p fuse block
• Linear exhaust gas recirculation (egr) solenoid valve (top front of engine)
• Nca
• Pnk
• Pnk pnk pnk
• Post-converter oxygen sensor (rear of catalytic converter)
• Pressure control solenoid (pcs)
• Red
• Tan
• Tcc on/off sol.
• Tcc pwm sol.
• Transmission fluid temperature (tft) sensor (internal)
• Transmission range (tr) pressure switch assembly

4.3L (VIN W), Engine Performance Wiring Diagrams (3 of 4) for Chevrolet S10 Pickup 1996

List of elements for 4.3L (VIN W), Engine Performance Wiring Diagrams (3 of 4) for Chevrolet S10 Pickup 1996:

• (rear of left cylinder head) g114
• (rear of right cylinder head) g117
• 5v ref
• A/t only
• Ecm batt fuse 9 20a
• Engine coolant temperature (ect) sensor (lower left side of engine)
• Four-wheel drive indicator assembly (center of floor console)
• Front axle switch (closed in 4wd) (front axle, right of differential)
• Fuel pump & sender (top of fuel tank)
• Fuel pump oil pressure switch (top rear of engine near distributor)
• Fuel pump prime connector
• Fuel pump relay
• Fuel tank pressure sensor
• G114 (rear of left cylinder head)
• Gauge input oil pressure
• Gauges fuse 4 10a
• Hot at all times
• Hot in run
• Hot in run, bulb test or start
• I/p fuse block
• Input fuel gauge
• Input speedometer
• Input tachometer
• Inside left frame rail
• Instrument cluster
• Intake air temperature (iat) sensor (left front of engine compartment in air intake duct)
• Malfunction indicator (mil) "service engine soon" lamp
• Manifold absolute pressure (map) sensor (top center of engine)
• Map
• Mass airflow sensor (left front of engine on air cleaner housing)
• Nca
• Pnk
• Red
• Ref lo
• Relay center
• Shift "upshift indicator" lamp
• Tan
• Tan a
• Temp
• Throttle position (tp) sensor (top left side of engine)
• Trans fuse 24 10a
• Transfer case control module (behind center of i/p)
• W/elec. shift ctrl
• W/o elec. shift ctrl

4.3L (VIN W), Engine Performance Wiring Diagrams (4 of 4) for Chevrolet S10 Pickup 1996

List of elements for 4.3L (VIN W), Engine Performance Wiring Diagrams (4 of 4) for Chevrolet S10 Pickup 1996:

• 12v ign feed
• 4wd fnt whl lock
• 4wd low ind sig
• 5v ref. voltage
• 5v return
• A/c high pressure cut/out switch (rear of a/c compressor)
• A/c on input
• A/t
• A/t only
• Abs enable relay
• Abs pump feed output
• Abs relay
• Abs voltage
• Abs warning lp ctrl
• Anti-lock brakes system (brake pressure warning switch)
• Brake fuse 12 10a
• Brake input
• Brake press sw input
• Brake pressure modulator valve (left rear of engine compartment)
• Brake switch input
• Brake warning lp ctrl
• Bravada
• Bravada only
• C4 b
• Clutch pedal position switch (on clutch pedal support bracket)
• Cruise control module (left rear of engine compartment, on cowl)
• Cruise ctrl eng sig
• Cruise on signal
• Cylinder no.1
• Cylinder no.2
• Cylinder no.3
• Cylinder no.4
• Cylinder no.5
• Cylinder no.6
• Data link connector (dlc) (lower left side of i/p)
• Distributor (top rear of engine)
• Distributor ignition control module (top right side of engine)
• Driver information display center (front of overhead console)
• Est output sig
• Fuel level input
• Fuel pump rly ctrl
• G114 (rear of left cylinder head)
• G117 (rear of right cylinder head)
• Ground
• High voltage coil wire
• Hot in run
• I/p fuse block
• Ign timing sig.
• Ignition coil (top right side of engine)
• Ignition feed
• Instrument cluster system (anti-lock ind., diode module & brake ind.)
• Isolation solenoid
• Left fnt pwm sol ctrl
• Left front
• Left front iso sol
• M/t
• Mil control
• Nca
• Pnk
• Pnk a
• Press ctrl sol lo
• Press ctrl sol. hi
• Pump drive output
• Pump driver feedback
• Pwm solenoid
• Range signal "a"
• Range signal "b"
• Range signal "c"
• Rear
• Rear iso sol ctrl
• Rear pwm sol ctrl
• Red
• Right fnt pwm sol ctrl
• Right front
• Right front iso sol
• Sensor ground
• Serial data sig
• Spark plugs
• System ground
• Tach. sig.
• Tcc/stoplamp switch (tcc/cruise release switch) (n.c) (on brake pedal support bracket)
• Upshift ind lp ctrl
• Utility
• Utility only
• Vehicle control module (vcm) (right side of engine compartment)
• Vss input
• Vss sig (4000 ppm)
• W/elec shift ctrl
• W/o elec shift ctrl

4.3L (VIN X), Engine Performance Wiring Diagrams (1 of 4) for Chevrolet S10 Pickup 1996

List of elements for 4.3L (VIN X), Engine Performance Wiring Diagrams (1 of 4) for Chevrolet S10 Pickup 1996:

• (a/t)
• (m/t)
• 1-2 shift sol. ctrl
• 2-3 shift sol. ctrl
• 3-2 ctrl sol. ctrl
• A/c comp rly ctrl
• A/c compressor clutch relay (center rear of engine compartment)
• Anti-lock brake system (left front wheel speed sensor)
• Anti-lock brakes system (right front wheel speed sensor)
• Cam posit sens rtn
• Cam posit sens sig
• Camshaft position sensor (located within high voltage switch) (in distributor)
• Canister vent val sol
• Coil
• Crank posit sens ground
• Crank posit sens signal
• Crankshaft position sensor (lower right front of engine)
• Ect sens input
• Egr pintle posit input
• Evap emiss purge ctrl
• Evaporative emissions canister purge solenoid (evap) (top right center of engine)
• Evaporative emissions canister vent valve solenoid (if equipped)
• Fuel level input
• G114 (rear of left cylinder head)
• Hall effect sensor
• Iat temp sens sig
• Idle air control motor (top left side of engine)
• Idle air ctrl (iac) a hi
• Idle air ctrl (iac) a lo
• Idle air ctrl (iac) b hi
• Idle air ctrl (iac) b lo
• Ignition feed
• Inj no.1 ctrl
• Inj no.2 ctrl
• Inj no.3 ctrl
• Inj no.4 ctrl
• Inj no.5 ctrl
• Inj no.6 ctrl
• Knock sens sig
• Knock sensor (top rear of engine)
• Left bnk o2 sens hi
• Left bnk o2 sens lo
• Left front sens high
• Left front sens low
• Left oxygen sensor (in left exhaust pipe)
• Map sens input
• Mass air flow input
• Nca
• Pnk
• Pnk a
• Pnk c
• Post-ctlyst o2 sens hi
• Post-ctylst o2 sens lo
• Pre-converter oxygen sensor (forward of catalytic converter)
• Pre-ctlyst o2 sens hi
• Pre-ctlyst o2 sens lo
• Pump driver
• Pump motor relay
• Right bnk o2 sens hi
• Right bnk o2 sens lo
• Right front sens high
• Right front sens low
• Right oxygen sensor (right rear of engine in exhaust pipe)
• Sensor ground
• Tan
• Tcc on/off sol. ctrl
• Tcc pwm sol ctrl
• Tft sig
• Throttle posit sens
• Vehicle control module (vcm) (right side of engine compartment)
• Vehicle speed sensor (vss) (rear of transfer case) (a/t & 4wd) (left side of transmission) (m/t)
• Vss (hi)
• Vss (lo)

4.3L (VIN X), Engine Performance Wiring Diagrams (2 of 4) for Chevrolet S10 Pickup 1996

List of elements for 4.3L (VIN X), Engine Performance Wiring Diagrams (2 of 4) for Chevrolet S10 Pickup 1996:

• 1-2 shift sol.
• 2-3 shift sol.
• 3-2 control sol.
• Automatic transmission
• Ecm/ign fuse 10 20a
• Eng fuse 5 20a
• Fuel inj. no.1
• Fuel inj. no.2
• Fuel inj. no.3
• Fuel inj. no.4
• Fuel inj. no.5
• Fuel inj. no.6
• Hot in run, bulb test, or start
• I/p fuse block
• Linear exhaust gas recirculation (egr) solenoid valve (top front of engine)
• Nca
• Pnk
• Pnk pnk pnk
• Post-converter oxygen sensor (rear of catalytic converter)
• Pressure control solenoid (pcs)
• Red
• Tan
• Tcc on/off sol.
• Tcc pwm sol.
• Transmission fluid temperature (tft) sensor (internal)
• Transmission range (tr) pressure switch assembly

4.3L (VIN X), Engine Performance Wiring Diagrams (3 of 4) for Chevrolet S10 Pickup 1996

List of elements for 4.3L (VIN X), Engine Performance Wiring Diagrams (3 of 4) for Chevrolet S10 Pickup 1996:

• (rear of left cylinder head) g114
• (rear of right cylinder head) g117
• 5v ref
• A/t only
• Ecm batt fuse 9 20a
• Engine coolant temperature (ect) sensor (lower left side of engine)
• Four-wheel drive indicator assembly (center of floor console)
• Front axle switch (closed in 4wd) (front axle, right of differential)
• Fuel pump & sender (top of fuel tank)
• Fuel pump oil pressure switch (top rear of engine near distributor)
• Fuel pump prime connector
• Fuel pump relay
• Fuel tank pressure sensor
• G114 (rear of left cylinder head)
• Gauge input oil pressure
• Gauges fuse 4 10a
• Hot at all times
• Hot in run
• Hot in run, bulb test or start
• I/p fuse block
• Input fuel gauge
• Input speedometer
• Input tachometer
• Inside left frame rail
• Instrument cluster
• Intake air temperature (iat) sensor (left front of engine compartment in air intake duct)
• Malfunction indicator (mil) "service engine soon" lamp
• Manifold absolute pressure (map) sensor (top center of engine)
• Map
• Mass airflow sensor (left front of engine on air cleaner housing)
• Nca
• Pnk
• Red
• Ref lo
• Relay center
• Shift "upshift indicator" lamp
• Tan
• Tan a
• Temp
• Throttle position (tp) sensor (top left side of engine)
• Trans fuse 24 10a
• Transfer case control module (behind center of i/p)
• W/elec. shift ctrl
• W/o elec. shift ctrl

4.3L (VIN X), Engine Performance Wiring Diagrams (4 of 4) for Chevrolet S10 Pickup 1996

List of elements for 4.3L (VIN X), Engine Performance Wiring Diagrams (4 of 4) for Chevrolet S10 Pickup 1996:

• 12v ign feed
• 4wd fnt whl lock
• 4wd low ind sig
• 5v ref. voltage
• 5v return
• A/c high pressure cut/out switch (rear of a/c compressor)
• A/c on input
• A/t
• A/t only
• Abs enable relay
• Abs pump feed output
• Abs relay
• Abs voltage
• Abs warning lp ctrl
• Anti-lock brakes system (brake pressure warning switch)
• Brake fuse 12 10a
• Brake input
• Brake press sw input
• Brake pressure modulator valve (left rear of engine compartment)
• Brake switch input
• Brake warning lp ctrl
• Bravada
• Bravada only
• C4 b
• Clutch pedal position switch (on clutch pedal support bracket)
• Cruise control module (left rear of engine compartment, on cowl)
• Cruise ctrl eng sig
• Cruise on signal
• Cylinder no.1
• Cylinder no.2
• Cylinder no.3
• Cylinder no.4
• Cylinder no.5
• Cylinder no.6
• Data link connector (dlc) (lower left side of i/p)
• Distributor (top rear of engine)
• Distributor ignition control module (top right side of engine)
• Driver information display center (front of overhead console)
• Est output sig
• Fuel level input
• Fuel pump rly ctrl
• G114 (rear of left cylinder head)
• G117 (rear of right cylinder head)
• Ground
• High voltage coil wire
• Hot in run
• I/p fuse block
• Ign timing sig.
• Ignition coil (top right side of engine)
• Ignition feed
• Instrument cluster system (anti-lock ind., diode module & brake ind.)
• Isolation solenoid
• Left fnt pwm sol ctrl
• Left front
• Left front iso sol
• M/t
• Mil control
• Nca
• Pnk
• Pnk a
• Press ctrl sol lo
• Press ctrl sol. hi
• Pump drive output
• Pump driver feedback
• Pwm solenoid
• Range signal "a"
• Range signal "b"
• Range signal "c"
• Rear
• Rear iso sol ctrl
• Rear pwm sol ctrl
• Red
• Right fnt pwm sol ctrl
• Right front
• Right front iso sol
• Sensor ground
• Serial data sig
• Spark plugs
• System ground
• Tach. sig.
• Tcc/stoplamp switch (tcc/cruise release switch) (n.c) (on brake pedal support bracket)
• Upshift ind lp ctrl
• Utility
• Utility only
• Vehicle control module (vcm) (right side of engine compartment)
• Vss input
• Vss sig (4000 ppm)
• W/elec shift ctrl
• W/o elec shift ctrl

EXTERIOR LIGHTS

Backup Lamps Wiring Diagram for Chevrolet S10 Pickup 1996

List of elements for Backup Lamps Wiring Diagram for Chevrolet S10 Pickup 1996:

• (4 cyl.: right side of engine; 6 cyl.: left side of trans.) backup lamp switch
• (inside left rear frame rail)
• A/t
• Hot in run, bulb test or start
• I/p fuse block
• Left backup lamp
• M/t
• Park/neutral position (pnp) switch (left side trans.)
• Pnk
• Right backup lamp
• Trailer wiring provision (w/ trailer tow pkg.)
• Turn b/u fuse 16 15a

Exterior Lamps Wiring Diagram for Chevrolet S10 Pickup 1996

List of elements for Exterior Lamps Wiring Diagram for Chevrolet S10 Pickup 1996:

• (inside left rear frame rail)
• (on brake pedal support bracket)
• Auxiliary lead (taped near junction block)
• Backup lamps circuit
• Center high mounted stop lamp (chmsl)
• Cruise control system
• G108 (left radiator support)
• G109 (right radiator support)
• G114 (rear of left cylinder head)
• G117 (rear of right cylinder head)
• Hazard
• Hazard flasher
• Head
• Headlamp switch
• Hot at all times
• Hot in run, bulb test or start
• I/p fuse block
• In-line fuse 30a
• Instrument cluster
• Interior lights system
• Junction block (left rear engine compt)
• Left front marker lamp
• Left front park/ turn lamp
• Left license lamp
• Left rear side marker lamp
• Left tail/ stop/ turn lamp
• Left turn
• Left turn ind.
• Normal
• Off
• Park
• Pk lps fuse 3 20a
• Pnk
• Power distribution center
• Power distribution center (behind center of i/p)
• Red
• Right front marker lamp
• Right front park/ turn lamp
• Right license lamp
• Right rear side marker lamp
• Right tail/ stop/ turn lamp
• Right turn
• Right turn ind.
• Stop haz fuse 1 20a
• Stop lamp relay (center rear of engine compt.)
• Tcc/stop lamp switch
• Trailer wiring provision
• Turn b/u fuse 16 15a
• Turn flasher
• Turn- hazard switch
• W/optional trailer tow package

GROUND DISTRIBUTION

Ground Distribution Wiring Diagram (1 of 2) for Chevrolet S10 Pickup 1996

List of elements for Ground Distribution Wiring Diagram (1 of 2) for Chevrolet S10 Pickup 1996:

• (4.3l only)
• (cut
• (cut wire)
• (rear of left cylinder head)
• 2.2l
• 4.3l
• 4wd indicator lamp
• A12
• Battery
• Brake pressure modulator valve
• Brake pressure warning switch
• Brake transmission shift interlock
• C10
• Center high mount stop lamp
• Cigarette lighter
• D10
• D12
• D13
• Data link connector
• Diagnostic energy reserve module
• Distributor ignition control module
• Door lock relay
• Drl relay
• Fuel pump and sender
• G101 (right front frame)
• G108 (left radiator support)
• G109 (left radiator support)
• G109 (right radiator support)
• G112 (left side of engine below exhaust manifold)
• G114
• G114 (rear of left cylinder head)
• G117 (rear of right cylinder head)
• G120 (engine block, near generator)
• I/p compartment box lamp
• Ignition switch
• Illuminated entry module
• Inside rear view mirror assembly
• Instrument cluster
• Left discriminating sensor
• Left door handle switch
• Left door jamb switch
• Left door lock switch
• Left horn
• Left low beam headlamp (w/ composite lamps)
• Left park/turn lamp
• Left power window switch
• Left vanity mirror
• Mass air flow sensor
• Outside rear view mirror switch
• Panel dimmer switch
• Powertrain control module
• Rear window washer pump
• Relay center
• Resistor
• Right discriminating sensor
• Right door handle switch
• Right door jamb switch
• Right headlamp (w/ sealed beam lamps)
• Right high beam headlamp (w/ composite lamps)
• Right horn
• Right low beam headlamp (w/ composite lamps)
• Right park/turn lamp
• Right power window switch
• Right vanity mirror
• Rke module
• Tan
• To g114
• Transfer case control module (4.3l only)
• Under- hood lamp
• Vehicle control module
• W/o rke
• Windshield washer pump
• Wiper motor
• Wire)

Ground Distribution Wiring Diagram (2 of 2) for Chevrolet S10 Pickup 1996

List of elements for Ground Distribution Wiring Diagram (2 of 2) for Chevrolet S10 Pickup 1996:

• (inside left rear frame rail)
• A/c compressor clutch
• A/c compressor clutch diode
• Ashtray lamp
• Audio alarm module
• Blower motor
• Blower motor relay
• Cruise control module
• Data link connector
• Diagnostic energy reserve module
• Drl module
• Fog lamp switch
• From wiper motor
• Fuel pump and sender
• Fuel pump relay
• G114 (rear of left cylinder head)
• G117 (rear of right cylinder head)
• Heater-a/c control lamp
• Heater-a/c control selector switch
• Instrument cluster
• Left
• Left backup lamp
• Left fog lamp
• Left oxygen sensor (4.3l only)
• Left rear marker lamp
• Left tail/stop turn lamp
• License lamp
• Outside air valve actuator motor
• Park/ neutral position switch
• Post convereter oxygen sensor (2.2l only)
• Post convereter oxygen sensor (4.3l only)
• Power distribution center
• Pre convereter oxygen sensor (4.3l only)
• Radio
• Relay center
• Right
• Right backup lamp
• Right fog lamp
• Right oxygen sensor (4.3l only)
• Right rear marker lamp
• Right tail/stop turn lamp
• Safety belt retractor switch
• Starter relay
• Steering column ground
• Stop lamp relay
• Trailer wiring provision

HEADLIGHTS

Headlight Wiring Diagram, with Composite Headlamps for Chevrolet S10 Pickup 1996

List of elements for Headlight Wiring Diagram, with Composite Headlamps for Chevrolet S10 Pickup 1996:

• A/t
• Accy
• B6 b6
• Bulb check
• Bulb test
• C206
• Daytime running lamps (drl) module (between hvac module and glove box)
• Daytime running lamps (drl) relay (in relay center)
• Drl indi- cator
• Drl relay ctrl
• Drl/fog fuse 15 10a
• E11
• E12
• E13
• Exterior lights system
• Fog lamp relay (behind glove compt., attached to relay center)
• Fog lamp switch
• Fog lamps
• G108 (left radiator support)
• G108 (left upper radiator support)
• G109 (right radiator support)
• G112 (4 cyl.) (left side of engine)
• G114 (6 cyl.) (rear of left cylinder head)
• Gauges fuse 4 10a
• Ground
• Head
• Headlamp dimmer switch
• Headlamp switch
• Hi beam indi- cator
• Hi bm feed
• Hi bm indicator
• Hot at all times
• Hot in run, bulb test or start
• I/p fuse block
• Ignition
• Ignition switch
• Illum lamp
• Instru- ment cluster system
• Instrument cluster
• Interior lights system
• Lamp feed
• Left fog lamp
• Left head- lamp
• Lock
• M/t
• Nca
• Off
• On indicator
• Park
• Park brake warning switch (on park brake)
• Pnk
• Right fog lamp
• Right head- lamp
• Run
• Start
• System
• Tan
• Trunk, tailgate,

Headlight Wiring Diagram, with Sealed Beam Lamps for Chevrolet S10 Pickup 1996

List of elements for Headlight Wiring Diagram, with Sealed Beam Lamps for Chevrolet S10 Pickup 1996:

• 1996 vftc c
• A/t
• Accy
• B6 b6
• Bulb check
• Bulb test
• C206
• Daytime running lamps (drl) module (between hvac module and glove box)
• Daytime running lamps (drl) relay (in relay center)
• Drl indi- cator
• Drl relay ctrl
• Drl/fog fuse 15 10a
• E11
• E12
• E13
• Exterior lights system
• Fog lamp relay (behind glove compt., attached to relay center)
• Fog lamp switch
• Fog lamps
• G108 (left upper radiator support)
• G109 (right radiator support)
• G112 (4 cyl.) (left side of engine)
• G114 (6 cyl.) (rear of left cylinder head)
• Gauges fuse 4 10a
• Ground
• Head
• Headlamp dimmer switch
• Headlamp switch
• Hi beam indi- cator
• Hi bm feed
• Hi bm indicator
• Hot at all times
• Hot in run, bulb test or start
• I/p fuse block
• Ignition
• Ignition switch
• Illum lamp
• Instru- ment cluster system
• Instrument cluster
• Interior lights system
• Lamp feed
• Left fog lamp
• Left head- lamp
• Lock
• M/t
• Nca
• Off
• On indicator
• Park
• Park brake warning switch (on park brake)
• Pnk
• Right fog lamp
• Right head- lamp
• Run
• Start
• System
• Tan
• Trunk, tailgate,

HORN

Horn Wiring Diagram for Chevrolet S10 Pickup 1996

List of elements for Horn Wiring Diagram for Chevrolet S10 Pickup 1996:

• (left
• (right
• C 1995 vftc
• Ctsy fuse 2 20a
• G108 radiator support)
• G109 radiator support)
• Horn
• Horn brush slip ring
• Horn relay
• Hot at all times
• I/p fuse block
• Left horn (left fender well)
• Relay center (behind i/p compartment box)
• Right horn (right fender well)
• Steering wheel
• Switches

INSTRUMENT CLUSTER

Instrument Cluster Wiring Diagram (1 of 2) for Chevrolet S10 Pickup 1996

List of elements for Instrument Cluster Wiring Diagram (1 of 2) for Chevrolet S10 Pickup 1996:

• (mil)
• (pick-up) (2.2l utility) (4.3l utility)
• (right side engine compt)
• (right side of engine compt) powertrain control module
• (right side of engine) ignition coil
• 4 cyl.
• 510 ohm
• 6 cyl.
• Air bag ind.
• Anti-lock brakes system
• Anti-lock brakes warning ind.
• Battery ind.
• Brake ind.
• Check gages ind.
• Check gages lamp driver
• Drl ind.
• Engine coolant temperature sender (lower left side of engine)
• Engine coolant temperature sensor (top front of engine)
• Exterior lights system
• Fuel gauge
• Fuel pump & sender (in fuel tank)
• Fuel pump/ oil pressure switch & sender (4 cyl.-right side of engine) (6 cyl.-near distributor)
• Fuse block: i/p
• G112 (left side of engine, below exhaust manifold)
• G114 g112 g117
• Gauges fuse 4 10a
• Head-
• Headlights
• Headlights system
• Hi beam ind.
• Hot at all times
• Hot in run
• Hot in run, bulb test or start
• Illumination lights (7-bulbs)
• Instrument cluster
• Interior lights system
• Left side of engine) rear of right cyl. head)
• Left turn ind.
• Light switch
• Mil ctrl
• Off
• Oil gauge
• Park/ neutral position switch
• Pnk
• Powertrain control module
• Powertrain control module (right side engine compt)
• Prndl circuit board
• Rear of left cyl. head) (pick-up: (2.2l utility: (4.3l utility:
• Right turn ind.
• Safety belt ind.
• Service engine soon ind.
• Shift ind.
• Shift lamp ctrl
• Solid state speedo/ tach
• Starting/ charging system
• System
• Tach out
• Tan
• Temp gauge
• Trans fuse 24 10a
• Vehicle control module
• Vehicle control module (right side engine compt)
• Volt meter
• Vss out
• Warning system

Instrument Cluster Wiring Diagram (2 of 2) for Chevrolet S10 Pickup 1996

List of elements for Instrument Cluster Wiring Diagram (2 of 2) for Chevrolet S10 Pickup 1996:

• (left side eng compt)
• 4 cyl.
• 6 cyl.
• A/t
• Acc
• Brake ind ctrl
• Brake pressure input
• Brake pressure modulator valve
• Brake pressure warning switch (left rear eng compt)
• Brake pressure warning switch (left rear engine compt)
• Bulb check
• Bulb test
• Daytime running lights module (above steering column)
• Diode module (above steering column)
• G112 (4 cyl.) (left side of engine, below (exhaust mainifold)
• G117 (6 cyl.) (rear of right cylinder head)
• Liftgate release solenoid (inside endgate)
• Lock
• M/t
• Nca
• Off
• Park brake warning switch (at park brake pedal)
• Run
• Start
• Vehicle control module (right side of engine compt)

INTERIOR LIGHTS

Courtesy Lamps Wiring Diagram for Chevrolet S10 Pickup 1996

List of elements for Courtesy Lamps Wiring Diagram for Chevrolet S10 Pickup 1996:

• (lower center of i/p)
• Bat
• Battery
• Courtesy switch
• Ctsy fuse 2 20a
• Dome lamp
• Door jamb switch input
• G112 (left side
• Gauges fuse 4 10a
• Grd
• Headlamp switch
• Hot at all times
• Hot in accy or run
• Hot in run, bulb test or start
• I/p compartment box lamp
• I/p fuse block
• Ign
• Illuminated entry
• Inside rearview mirror
• Interior lamp control module
• Lamp control
• Left door jamb switch
• Left i/p courtesy lamp
• Left vanity mirror lamp
• Map lamps
• Of engine)
• Panel dimmer switch
• Park lps fuse 3 20a
• Pnk
• Radio fuse 11 20a
• Remote keyless entry module (near park brake)
• Right door jamb switch
• Right i/p courtesy lamp
• Right vanity mirror lamp
• Transfer case control module (center of i/p)
• Underhood lamp

Instrument Illumination Wiring Diagram for Chevrolet S10 Pickup 1996

List of elements for Instrument Illumination Wiring Diagram for Chevrolet S10 Pickup 1996:

• (7) bulbs
• (left side of engine-pickup 2.2l, rear of right cylinder head-pickup except 2.2l, rear of left cylinder head-utility)
• 4wd indicator switch lamp
• Ash tray lamp
• Audio alarm module
• Automatic transmission position indicator lamp (bravada)
• Center
• Dim
• Display dim signal
• Driver information display control module
• Ecm batt fuse 9 20a
• Fog light switch
• G112-pickup 2.2l g117-pickup except 2.2l g114-utility
• Head
• Headlight switch
• High
• Hot at all times
• Hvac control module
• I/p dimmer switch
• I/p fuse block
• Illum fuse 21 10a
• Instrument cluster
• Lift- gate release switch
• Light switch
• Lights on input
• Off
• Park
• Power distribution
• Radio
• Rear window defogger switch
• Rear window wiper/ washer switch
• Underhood lamp

POWER DISTRIBUTION

Power Distribution Wiring Diagram (1 of 4) for Chevrolet S10 Pickup 1996

List of elements for Power Distribution Wiring Diagram (1 of 4) for Chevrolet S10 Pickup 1996:

• 4wd fuse 19 20a
• Audio alarm module
• Battery
• Blower motor relay
• Brake pressure modulator valve
• C 1995 vftc
• D14
• D15
• Data link connector (dlc)
• Daytime running light (drl) relay
• Door lock relay
• Driver's lumbar support pump
• Driver's power seat assembly
• Drl/fog fuse 15 10a
• Ecm batt fuse 9 20a
• Fog lamp relay
• Fuel pump oil pressure switch
• Fuel pump relay
• Generator
• Hazard flasher
• Head
• Headlight switch
• I/p fuse block
• Junction block
• Left door lock switch
• Off
• Park
• Passenger's lumbar support pump
• Pcm
• Pickup
• Pk lps fuse 3 20a
• Power auxiliary outlet
• Powertrain control module (pcm)
• Pwr acc circuit breaker a 20a
• Pwr aux fuse 7 25a
• Radio
• Rdo batt fuse 13 10a
• Rear window wiper motor and module (utility only)
• Red
• Red red
• Remote keyless entry module
• Right door lock switch
• Starter solenoid
• Stop-haz fuse 1 20a
• Tcc/ stoplamp switch
• To i/p fuse block
• To ignition switch
• Transfer case control module
• Underhood lamp
• Utility
• Utility only
• Vcm
• Vehicle control module (vcm)
• W/ 4.3l only
• W/ electronic shift 4wd only

Power Distribution Wiring Diagram (2 of 4) for Chevrolet S10 Pickup 1996

List of elements for Power Distribution Wiring Diagram (2 of 4) for Chevrolet S10 Pickup 1996:

• (blazer/jimmy) b
• (bravada) d
• 2 door
• 20a
• 4 door
• A13
• Accy
• Air valve actuator motor
• All except 2.2l base models
• Block
• Brake fuse 12 10a
• Brake pressure modulator valve
• Bulb test
• C 1995 vftc
• C206
• Cruise control module
• Cruise control switch
• Driver information display control module
• From fusible link
• Htr a/c fuse 6 20a
• Hvac select switch
• I/p fuse
• Ignition
• Inside rearview mirror lamp
• Left front window switch
• Lock
• Nca
• Off
• Pwr wdo circuit breaker b 30a
• Radio
• Radio fuse 11
• Rear window wiper/ washer switch (utility only)
• Red d2
• Right front window switch
• Run
• Start
• Switch
• Tcc/ stoplamp switch
• Vehicle control module
• W/ overhead console
• W/o overhead console
• Window lockout switch
• Windshield wiper motor and module
• Windshield wiper/ washer switch
• Wiper fuse 17 25a

Power Distribution Wiring Diagram (3 of 4) for Chevrolet S10 Pickup 1996

List of elements for Power Distribution Wiring Diagram (3 of 4) for Chevrolet S10 Pickup 1996:

• (4.3l vin w)
• (interior lights system)
• 2.2l
• 2wd m/t
• 4.3l
• 4wd m/t
• A/c compressor clutch relay
• A/t
• A/t only
• A10
• Accy
• Air bag fuse 22 10a
• Arming sensor
• Audio alarm module
• Auto trans shift lock control solenoid
• B10
• Backup light switch
• Bravada
• Bulb test
• C 1995 vftc
• C206
• Camshaft position sensor
• Clutch pedal position switch
• Clutch pedal position switch
• Crank fuse 20 10a
• Crankshaft position sensor
• D16
• Daytime running light (drl) module
• Daytime running light (drl) relay
• Diagnostic energy reserve module (derm)
• Diagnostic enrgy reserve module
• Distributor ignition control module
• Ecm ign fuse 10 20a
• Eng fuse 5 20a
• Entry
• Evaporative emissions canister purge solenoid
• Evaporative emissions canister vent valve solenoid
• Except bravada
• Four-wheel drive indicator
• From fusible link
• Front axle switch
• Fuel injector
• Fuel injectors
• Gauges fuse 4 10a
• I/p fuse block
• Ignition coil
• Ignition switch
• Illum fuse 14 10a
• Instrument cluster
• Interior light control module
• Interior lights
• Keyless entry module
• Left oxygen sensor
• Linear egr valve
• Lock
• M/t
• Mass airflow sensor
• Nca
• Off
• Panel dimmer switch assembly
• Park/ neutral position switch
• Park/neutral position switch
• Pnk
• Pnk a
• Pnk b
• Pnk b2
• Pnk c5
• Pnk c6
• Pnk d
• Pnk e
• Pnk f
• Post converter oxygen sensor
• Post- converter oxygen sensor
• Powertrain control module
• Powertrain control module (pcm)
• Pre- converter oxygen sensor
• Rear window defog switch
• Red
• Right oxygen sensor
• Run
• Start
• Trans fuse 24 10a
• Transfer case control module
• Transfer case select switch
• Transmission
• Turn b/u fuse 16 15a
• Turn signal flasher
• Vehicle control module
• Vehicle control module (vcm)
• W/ keyless
• W/ utility only
• W/ vcm only
• W/o keyless

Power Distribution Wiring Diagram (4 of 4) for Chevrolet S10 Pickup 1996

List of elements for Power Distribution Wiring Diagram (4 of 4) for Chevrolet S10 Pickup 1996:

• (blazer/jimmy)
• (bravada)
• (left side of engine)
• (right rear of engine)
• A/c comp fuse 14 10a
• A/c compressor clutch relay
• C 1995 vftc
• Cigarette lighter
• Dome lamp
• Driver information display center
• Endgate lock switch
• From fusible link
• G112 (2.2l)
• G117 (4.3l)
• Horn relay
• Horn/dm fuse 2 20a
• I/p compartment box lamp
• I/p fuse block
• Interior lamps control module
• Keyless entry module
• Left courtesy lamp
• Left vanity mirror
• Left vanity mirror lamp
• Liftgate glass release switch
• Pickup
• Power outside rearview mirror switch
• Rear dome lamp
• Rear window defog switch
• Rearview mirror lamps
• Red
• Remote keyless entry module
• Right i/p courtesy lamp
• Right vanity mirror
• Right vanity mirror lamp
• Rr defog fuse 8 30a
• Utility

POWER DOOR LOCKS

Door Lock Wiring Diagram for Chevrolet S10 Pickup 1996

List of elements for Door Lock Wiring Diagram for Chevrolet S10 Pickup 1996:

• Door lock relay (behind right side of i/p)
• G112 (left side of engine)
• Hot at all times
• I/p fuse block (left side of i/p)
• Left front door lock motor
• Left front door lock switch
• Lock
• Pwr accy circuit breaker a 20a
• Right front door lock motor
• Right front door lock switch
• Tan
• Tan a
• Unlock

Keyless Entry Wiring Diagram for Chevrolet S10 Pickup 1996

List of elements for Keyless Entry Wiring Diagram for Chevrolet S10 Pickup 1996:

• Batt
• C 1995 vftc
• Ctsy fuse 2 20a
• Data link connector (behind left
• Door lock relay (behind right side of i/p)
• G112 (left side of engine)
• Gauges fuse 4 20a
• Ground
• Hot at all times
• Hot in run, bulb test or start
• I/p fuse block (left side of i/p)
• Ignition
• Illum out
• Interior lights system
• Jamb sw in
• Left door jamb switch
• Left front door lock motor
• Left front door lock switch
• Lf unlck out
• Lock
• Lock output
• Lock relay
• Pnk
• Prgrm enable
• Pwr accy circuit breaker a 20a
• Remote keyless entry (rke) module (behind left hush panel)
• Right door jamb switch
• Right front door lock motor
• Right front door lock switch
• Side of i/p)
• Tan
• Unlck output
• Unlock
• Unlock relay

POWER MIRRORS

Power Mirror Wiring Diagram for Chevrolet S10 Pickup 1996

List of elements for Power Mirror Wiring Diagram for Chevrolet S10 Pickup 1996:

• 1996 vftc c
• Ctsy fuse 2 20a
• Down
• G117 (rear of right cylinder head)
• Hot at all times
• I/p fuse block
• Illumination
• Interior lights system
• Left
• Left outside rearview mirror
• Left/ right motor
• Mirror select switch
• Nca
• Power outside rearview mirror switch
• Right
• Right outside rearview mirror
• Up/down motor

POWER SEATS

6-Way Power Seat Wiring Diagram for Chevrolet S10 Pickup 1996

List of elements for 6-Way Power Seat Wiring Diagram for Chevrolet S10 Pickup 1996:

• (rear of right cylinder head)
• A nca
• B nca
• Back
• Down
• Entire seat
• For- ward
• Forward/ rearward motor
• Front height
• Front height motor
• G117
• Hot at all times
• I/p fuse block
• Nca
• Power seat actuator assembly
• Power seat control switch
• Pwr accy circuit breaker a 20a
• Rear height
• Rear height motor
• Tan

Lumbar Wiring Diagram for Chevrolet S10 Pickup 1996

List of elements for Lumbar Wiring Diagram for Chevrolet S10 Pickup 1996:

• C 1995 vftc
• G117 (rear of right cylinder head)
• Hot at all times
• I/p fuse block
• Left power lumbar support switch
• Nca
• Power accy circuit breaker a 20a
• Pump
• Right power lumbar support switch

POWER WINDOWS

Power Window Wiring Diagram, 2 Door for Chevrolet S10 Pickup 1996

List of elements for Power Window Wiring Diagram, 2 Door for Chevrolet S10 Pickup 1996:

• (pickup: rear of left cylinder head)
• (utility: right rear of cylinder head)
• C 1995 vftc
• Exp dn mod
• G112 (pickup)
• G117 (utility)
• Hot in run
• I/p fuse block (left side of i/p)
• Left front
• Left front window motor
• Left front window switch
• Pwr wdo circuit breaker 30a
• Right front
• Right front window motor
• Right front window switch
• Tan

Power Window Wiring Diagram, 4 Door for Chevrolet S10 Pickup 1996

List of elements for Power Window Wiring Diagram, 4 Door for Chevrolet S10 Pickup 1996:

• C 1995 vftc
• Exp dn mod
• G112 (2.2l) (4.3l: right rear of cylinder head) (2.2l: left side of engine)
• G117 (4.3l)
• Hot in run
• I/p fuse block (left side of i/p)
• Left front
• Left front window motor
• Left front window switch
• Left rear
• Left rear window motor
• Left rear window switch
• Pwr wdo circuit breaker 30a
• Right front
• Right front window motor
• Right front window switch
• Right rear
• Right rear window motor
• Right rear window switch
• Tan
• Window lockout switch

RADIO

Radio Wiring Diagrams for Chevrolet S10 Pickup 1996

List of elements for Radio Wiring Diagrams for Chevrolet S10 Pickup 1996:

• 2.2l
• 4.3l
• Antenna
• Antenna input
• Bat power
• Coaxial cable
• Disp dim signal
• G115 (rear of engine)
• Ground
• Hot at all times
• Hot in accy or run
• I/p fuse block
• Instrument cluster system
• Interior lights system
• Left front speaker
• Left rear speaker
• Lt frt spkr
• Lt rear spkr
• Panel light
• Power
• Powertrain control module
• Radio
• Radio fuse 11 20a
• Rdo-bat fuse 13 10a
• Right front speaker
• Right rear speaker
• Rt frt spkr
• Rt rear spkr
• S207
• S209
• S212
• Tan
• Vehicle control module
• Vss

SHIFT INTERLOCKS

Shift Interlock Wiring Diagram for Chevrolet S10 Pickup 1996

List of elements for Shift Interlock Wiring Diagram for Chevrolet S10 Pickup 1996:

• 1995 vftc c
• Brake/transmission shift interlock solenoid (on steering column)
• G112 (utility and 2.2l pickup) (left side of engine)
• G117 (4.3l pickup) (rear of right cylinder head)
• Hot in run bulb test or start
• I/p fuse block
• Park/ neutral position switch (left side of transmission)
• Pnk
• Tcc/ stoplamp switch (brake pedal support)
• Turn b/u fuse 16 15a

STARTING/CHARGING

Charging Wiring Diagram for Chevrolet S10 Pickup 1996

List of elements for Charging Wiring Diagram for Chevrolet S10 Pickup 1996:

• (near generator)
• (right front frame)
• (right radiator support)
• Battery
• Battery lamp
• G101
• G109
• G120
• Gauges fuse 4 10a
• Generator
• Hot in run, bulb test or start
• I/p fuse block
• Instrument cluster
• Ohms
• Pnk
• Power distribution system
• Red
• Starter relay
• Starter solenoid

Starting Wiring Diagram for Chevrolet S10 Pickup 1996

List of elements for Starting Wiring Diagram for Chevrolet S10 Pickup 1996:

• (left side of engine-pickup vin 4, rear of right cyl. head-pickup vin w or vin x, rear of left cyl. head-utility vin w or vin x)
• (left side of trans) park/neutral position switch
• (near generator)
• (right front frame)
• (right radiator support)
• A/t
• Accy
• Battery
• Battery junction block
• Bulb test
• Clutch pedal position switch (clutch pedal bracket)
• Crank fuse 20 10a
• Diagnostic energy reserve module
• G101
• G109
• G112 (pickup-vin 4) g117 (pickup-vin w or vin x) g114 (utility-vin w or vin x)
• G120
• Generator
• Hold- in coil
• I/p fuse block
• Ignition switch
• Lock
• M/t
• Nca
• Off
• Power distribution system
• Pull- in coil
• Red
• Run
• Start
• Starter motor
• Starter relay (center rear of engine compt.)
• Starter solenoid

SUPPLEMENTAL RESTRAINTS

Supplemental Restraint Wiring Diagram for Chevrolet S10 Pickup 1996

List of elements for Supplemental Restraint Wiring Diagram for Chevrolet S10 Pickup 1996:

• (806 or 1035)
• A/t
• A10
• A11
• A12
• Air bag fuse 22 10a
• Air bag warning lamp
• Arming sensor (left side frame rail, near center crossmember)
• B10
• B11
• B12
• Clutch pedal position switch (on pedal support)
• Crank fuse 20 10a
• Crank input
• Data link connector (behind left side of i/p)
• Diagnostic energy reserve module (derm) (behind right kick panel)
• Diagnostic requst in
• Driver 36 vlr
• Driver sense high
• Driver sense low
• Driver source sense
• G105 (right front frame rail)
• G114 (pickup) (rear of left cylinder head)
• G114 (rear of left cylinder head)
• G117 (utility) (rear of right cylinder head)
• Gauges fuse 4 10a
• Ground
• Hot in run, bulb test or start
• Hot in start
• I/p fuse block
• Ignition
• Instrument cluster
• Left forward discriminating sensor (left side of lower radiator support)
• M/t
• Nca
• Pnk
• Redundant indic, ign
• Right forward discriminating sensor (right side of lower radiator support)
• Safety belt switch
• Seat belt monitor
• Shorting bar
• Sir coil assembly (top of steering column)
• Sir indic low
• Starting/charging system (starter relay)
• Steering wheel inflator module (mounted on steering wheel)
• Tan
• Warning systems (audio alarm)

TRANSMISSION

2.2L

2.2L (VIN 4), Transmission Wiring Diagram for Chevrolet S10 Pickup 1996

List of elements for 2.2L (VIN 4), Transmission Wiring Diagram for Chevrolet S10 Pickup 1996:

• (eng harn, 19 cm from inj harn breakout) s115
• (eng harn, 34 cm from c175 breakout)
• (eng harn, 40 cm from c175 breakout)
• (left side of engine) g112
• 1-2 shift sol
• 1-2 shift sol ctrl
• 2-3 shift sol
• 2-3 shift sol ctrl
• 3-2 shift sol
• 3-2 shift sol ctrl
• 5v ref voltage
• Automatic transaxle
• Automatic transmission fluid pressure (tfp) manual valve position switch
• Brake fuse 12 20a
• Brake pedal sw in
• Cruise control
• Cruise on signal in
• Ecm batt fuse 9 20a
• Ecm ign fuse 10 20a
• Ect sensor in
• Engine controls
• Engine coolant temperature (ect) sensor (front of engine)
• Engine fuse 15 20a
• Fuse block
• G114 (left rear of cylinder head)
• Gauges fuse 4 20a
• Hot at all times
• Hot in run
• Hot in run, bulb test or start
• Instrument cluster
• Mil indic ctrl
• Park/neutral position switch (left side of transmission)
• Pc sol valve hi
• Pcm ground
• Pcs hi
• Pcs lo
• Pnk
• Pnp switch in
• Power (battery)
• Power (ignition 1)
• Power (ignition)
• Powertrain control module (right front corner of engine compartment)
• Red
• S100
• S101
• S106
• S107
• S109
• S112
• S116
• S227
• S237
• S277 (dash harn, 11 cm in tcc switch breakout)
• Sensor ground
• Sensor return
• Service engine soon indic
• Solenoid power
• Tcc on/off sol
• Tcc pwm signal
• Tcc pwm sol ctrl
• Tcc sol ctrl
• Tcc/stop lamp switch (under left side of i/p)
• Tft sensor signal
• Throttle position sensor (tps) (on side of throttle body)
• Tp sensor in
• Trans fuse 24 10a
• Trans range a in
• Trans range b in
• Trans range c in
• Trans temp out
• Vehicle speed sensor (side of transmission)
• Vss sensor in pc sol valve lo
• Vss sensor return

Transfer Case Wiring Diagram for Chevrolet S10 Pickup 1996

List of elements for Transfer Case Wiring Diagram for Chevrolet S10 Pickup 1996:

• (a/t) 4wd lo selected
• (a/t) pnp switch in (n)
• (a/t) pnp switch in (p)
• (center of i/p, above radio) transfer case select switch
• (m/t) pnp switch in (p)
• 12v battery
• 12v ignition
• 2 hi request
• 2 hi status lamp
• 2wd ind hi
• 2wd-hi
• 4 hi request
• 4 hi status lamp
• 4 lo request
• 4 lo status lamp
• 4wd fuse 19 20 amp
• 4wd hi
• 4wd ind hi
• 4wd ind lo
• 4wd lo
• 4wd lo in
• A/t only
• Axle sw in
• C10
• C11
• C12
• C14
• C16
• Chasis ground
• Crank fuse 20 10 amp
• D10
• D12
• D13
• D14
• D15
• D16
• Data link connector
• Encoder channel a
• Encoder channel b
• Encoder channel c
• Encoder channel d
• Encoder channel-a
• Encoder channel-b
• Encoder channel-c
• Encoder channel-d
• Encoder ground
• Encoder signal ground
• Front axle switch (on front axle)
• G112 (left cylinder head)
• G120 (right cylinder head)
• Gauges fuse 4 10 amp
• Hot at all times
• Hot in run or start
• Hot in run, bulb test or start
• Hot in start
• I/p fuse block (left end of i/p)
• M/t only
• Motor control a
• Motor control b
• Motor ground
• Park/neutral position and backup lamp switch (a/t only) (left side of transmission)
• Pickup
• Pk lps fuse 3 20 amp
• Pnk
• Pnk a
• Power ground
• Red
• S109
• S214
• S230
• S231
• S238
• S242
• Transfer case (left side of transfer case)
• Transfer case shift control module (behind center of i/p)
• Turn b/u fuse 16 15 amp
• Utility
• Vehicle control module (vcm) (right side of eng compartment)
• Vehicle spd out
• Vehicle speed in

4.3L

4.3L (VIN W), Transmission Wiring Diagram for Chevrolet S10 Pickup 1996

List of elements for 4.3L (VIN W), Transmission Wiring Diagram for Chevrolet S10 Pickup 1996:

• (behind left side of i/p)
• (dash harn, 20 cm from dlc) s110
• (eng harn, 19 cm from inj harn breakout) s115
• (left cylinder
• (upper intake manifold)
• 1-2 shift sol ctrl
• 1-2 shift sol.
• 2-3 shift sol ctrl
• 2-3 shift sol.
• 3-2 cntrl sol.
• 3-2 sol ctrl
• 5v reference
• All times
• And start
• Automatic transmission
• Battery feed
• Brake
• Brake signal
• Bravada only
• Cruise control
• Cruise engaged in
• Data link connector (below left side of i/p)
• Ecm batt
• Ecm ign fuse 10 20a
• Ect signal
• Engine controls
• Engine coolant temp sensor
• Fuse 12 10a
• Fuse 24 10a
• Fuse 9 20a
• G114 (left rear of engine)
• G115 (rear of engine)
• G117 (right rear of engine)
• Head)
• Hot at
• Hot in run
• Hot in run, bulb
• I/p fuse block
• Ignition feed
• Instrument cluster (bravada)
• Pnk
• Press ctrl sol "hi"
• Press ctrl sol "lo"
• Pressure control solenoid (pcs)
• Range signal "a"
• Range signal "b"
• Range signal "c"
• Red
• Run feed
• S106
• S107 (eng harn 34 cm from c175 breakout)
• S110
• S116
• S120
• S224
• Sensor ground
• Serial data
• System gnd
• Tcc brake and cruise control release switch (on brake pedal bracket)
• Tcc on/ off sol.
• Tcc pwm sol ctrl
• Tcc pwm sol.
• Tcc sol ctrl
• Test or start
• Tft signal
• Throttle position sensor
• Tp signal
• Trans
• Transmission fluid temperature (tft) sensor (internal)
• Transmission range (tr) pressure switch assembly
• Vehicle control module (vcm) (right side of eng compartment)
• Vehicle speed sensor (left rear of transmission)
• Vss hi
• Vss lo
• Vss output

4.3L (VIN X), Transmission Wiring Diagram for Chevrolet S10 Pickup 1996

List of elements for 4.3L (VIN X), Transmission Wiring Diagram for Chevrolet S10 Pickup 1996:

• (behind left side of i/p)
• (dash harn, 20 cm from dlc) s110
• (eng harn, 19 cm from inj harn breakout) s115
• (left cylinder
• (upper intake manifold)
• 1-2 shift sol ctrl
• 1-2 shift sol.
• 2-3 shift sol ctrl
• 2-3 shift sol.
• 3-2 cntrl sol.
• 3-2 sol ctrl
• 5v reference
• All times
• And start
• Automatic transmission
• Battery feed
• Brake
• Brake signal
• Bravada only
• Cruise control
• Cruise engaged in
• Data link connector (below left side of i/p)
• Ecm batt
• Ecm ign fuse 10 20a
• Ect signal
• Engine controls
• Engine coolant temp sensor
• Fuse 12 10a
• Fuse 24 10a
• Fuse 9 20a
• G114 (left rear of engine)
• G115 (rear of engine)
• G117 (right rear of engine)
• Head)
• Hot at
• Hot in run
• Hot in run, bulb
• I/p fuse block
• Ignition feed
• Instrument cluster (bravada)
• Pnk
• Press ctrl sol "hi"
• Press ctrl sol "lo"
• Pressure control solenoid (pcs)
• Range signal "a"
• Range signal "b"
• Range signal "c"
• Red
• Run feed
• S106
• S107 (eng harn 34 cm from c175 breakout)
• S110
• S116
• S120
• S224
• Sensor ground
• Serial data
• System gnd
• Tcc brake and cruise control release switch (on brake pedal bracket)
• Tcc on/ off sol.
• Tcc pwm sol ctrl
• Tcc pwm sol.
• Tcc sol ctrl
• Test or start
• Tft signal
• Throttle position sensor
• Tp signal
• Trans
• Transmission fluid temperature (tft) sensor (internal)
• Transmission range (tr) pressure switch assembly
• Vehicle control module (vcm) (right side of eng compartment)
• Vehicle speed sensor (left rear of transmission)
• Vss hi
• Vss lo
• Vss output

Transfer Case Wiring Diagram for Chevrolet S10 Pickup 1996

List of elements for Transfer Case Wiring Diagram for Chevrolet S10 Pickup 1996:

• (a/t) 4wd lo selected
• (a/t) pnp switch in (n)
• (a/t) pnp switch in (p)
• (center of i/p, above radio) transfer case select switch
• (m/t) pnp switch in (p)
• 12v battery
• 12v ignition
• 2 hi request
• 2 hi status lamp
• 2wd ind hi
• 2wd-hi
• 4 hi request
• 4 hi status lamp
• 4 lo request
• 4 lo status lamp
• 4wd fuse 19 20 amp
• 4wd hi
• 4wd ind hi
• 4wd ind lo
• 4wd lo
• 4wd lo in
• A/t only
• Axle sw in
• C10
• C11
• C12
• C14
• C16
• Chasis ground
• Crank fuse 20 10 amp
• D10
• D12
• D13
• D14
• D15
• D16
• Data link connector
• Encoder channel a
• Encoder channel b
• Encoder channel c
• Encoder channel d
• Encoder channel-a
• Encoder channel-b
• Encoder channel-c
• Encoder channel-d
• Encoder ground
• Encoder signal ground
• Front axle switch (on front axle)
• G112 (left cylinder head)
• G120 (right cylinder head)
• Gauges fuse 4 10 amp
• Hot at all times
• Hot in run or start
• Hot in run, bulb test or start
• Hot in start
• I/p fuse block (left end of i/p)
• M/t only
• Motor control a
• Motor control b
• Motor ground
• Park/neutral position and backup lamp switch (a/t only) (left side of transmission)
• Pickup
• Pk lps fuse 3 20 amp
• Pnk
• Pnk a
• Power ground
• Red
• S109
• S214
• S230
• S231
• S238
• S242
• Transfer case (left side of transfer case)
• Transfer case shift control module (behind center of i/p)
• Turn b/u fuse 16 15 amp
• Utility
• Vehicle control module (vcm) (right side of eng compartment)
• Vehicle spd out
• Vehicle speed in

WARNING SYSTEMS

Warning System Wiring Diagrams for Chevrolet S10 Pickup 1996

List of elements for Warning System Wiring Diagrams for Chevrolet S10 Pickup 1996:

• Audio alarm module (power distribution center)
• Fasten belts out
• Fuse block
• G112 (l4 vin 4) (lower left side of engine)
• G115 (v6 vin w) (rear of engine)
• Gauges fuse 4 10a
• Ground
• Hot at all times
• Hot in park or head
• Hot in run, bulb test or start
• Ignition on in
• Illum fuse 21 10a
• Instrument cluster
• Key-in warning
• Key-in warning buzzer switch
• Left door jamb switch
• Lights on in
• Nca
• Pnk
• Power in
• Safety belt in
• Safety belt lamp
• Safety belt retractor switch
• Stop-hz fuse 1 20a
• Tan

WIPER/WASHER

Front Wiper/Washer Wiring Diagram for Chevrolet S10 Pickup 1996

List of elements for Front Wiper/Washer Wiring Diagram for Chevrolet S10 Pickup 1996:

• (left radiator support)
• (rear of left cylinder head)
• C 1995 vftc
• G108
• G114
• Hot in acc or run
• I/p fuse block
• Low
• Mist
• Off
• Pnk
• Pulse
• Solid state
• Washer switch
• Windshield washer pump (left front of engine compt, in washer reservoir)
• Windshield wiper motor and module (center rear of engine compt)
• Wiper fuse 17 25a
• Wiper switch
• Wiper/ washer switch