Alfa Romeo 159 1.9 JTD 16V Fino a 12/05 – MAIN BEAM HEADLAMPS – – Xenon Gas headlamps – WIRING DIAGRAM, LOCATION COMPONENTS, OPERATIONAL DESCRIPTION – WIRING DIAGRAM, LOCATION COMPONENTS, OPERATIONAL DESCRIPTION

WIRING DIAGRAM - MAIN BEAM HEADLAMPS - Alfa Romeo 159 1.9 JTD 16V Fino a 12/05

MAIN BEAM HEADLIGHTS - WIRING DIAGRAM Alfa Romeo 159 1.9 JTD 16V Fino a 12/05

COMPONENTS - MAIN BEAM HEADLAMPS - Alfa Romeo 159 1.9 JTD 16V Fino a 12/05

Component code	Description	Reference to the operation
B001	JUNCTION UNIT
B002	JUNCTION UNIT UNDER DASHBOARD
B099	MAXIFUSE BOX ON BATTERY
C010	LEFT FRONT EARTH	-
C011	RIGHT FRONT EARTH	-
C020	PASSENGER SIDE DASHBOARD EARTH	-
D001	FRONT/DASHBOARD COUPLING	-
E050	INSTRUMENT PANEL
F010	LEFT HEADLAMP
F011	RIGHT HEADLAMP
H005	STEERING COLUMN SWITCH UNIT
M001	BODY COMPUTER
M089	STEERING LOCK CONTROL UNIT (NBS)

COMPONENT LOCATION - MAIN BEAM HEADLAMPS - Alfa Romeo 159 1.9 JTD 16V Fino a 12/05

MAIN BEAM HEADLIGHTS - COMPONENT LOCATION Alfa Romeo 159 1.9 JTD 16V Fino a 12/05

获取访问所有汽车的接线图

Component code	Description	Reference to the operation
B001	JUNCTION UNIT
B002	JUNCTION UNIT UNDER DASHBOARD
B099	MAXIFUSE BOX ON BATTERY
C010	LEFT FRONT EARTH	-
C011	RIGHT FRONT EARTH	-
C020	PASSENGER SIDE DASHBOARD EARTH	-
D001	FRONT/DASHBOARD COUPLING	-
E050	INSTRUMENT PANEL
F010	LEFT HEADLAMP
F011	RIGHT HEADLAMP
H005	STEERING COLUMN SWITCH UNIT
M001	BODY COMPUTER
M089	STEERING LOCK CONTROL UNIT (NBS)

DESCRIPTION - MAIN BEAM HEADLAMPS - Alfa Romeo 159 1.9 JTD 16V Fino a 12/05

If the vehicle is equipped with GAS DISCHARGE headlamps, there are two main beams: the first is a specific SPOT light, the second a gas discharge bulb that lights up like a full beam once the shutter for the dipped beam mode is raised.The main beams are switched on by the steering column switch unit:- with the dipped beams on, by pushing the lever towards the dashboard (stable mode)- in flashing mode, by pulling the lever toward the steering wheel (unstable mode)The switching between the dipped beam and main beam functions for xenon bulbs causes the raising of the shutter in the gas discharge bulb, with the switch to the main beam; at the same time, the main beam SPOT light also comes on. The spot light main beam comes on by itself through the flasher control (unstable mode) with the main beams switched off.The low beam activation relay is controlled by the Body Computer relay energizing is activated by enablement signals with the TEG inserted (INT) and from the specific signal from the steering column switch unit.Activation/deactivation information is sent via the CAN network: in this way, the main beam warning light is activated in the instrument panel.767for legal reasons, if the dusk sensor is activated, only the flasher can be operated and the main beams cannot be turned on permanently; the AUTO function must be switched off in order to activate these lights.

FUNCTIONAL DESCRIPTION - MAIN BEAM HEADLAMPS - Alfa Romeo 159 1.9 JTD 16V Fino a 12/05

The dipped headlamps (earth) activation signal (stable mode) is sent to pin 4 of connector I of the Body Computer M1 from the steering column switch unit H5; the flasher activation (earth) signal (unstable mode) is, on the other hand, sent to pin 33 of connector G of the Body Computer M1.The Body Computer M1 controls the supply for the dipped headlamps sending an earth signal to relay T2 in the junction unit in the engine compartment B1 from pin 9 of connector A of M1 which energizes relay T2: this supplies the dipped headlamps F10 (left) and F11 (right). Each circuit is protected by a fuse in the junction unit B1 : F15 for the left headlamp and F14 for the right.Both electronic systems inside the headlamps F10 (left) and F11 (right) are supplied - pin 9 - from the INT line of junction unit B2 protected by fuse F37.Pins 12 of the two control units are connected to one another by means of a special serial line, whilst the speedometer signal from the Body Computer M1 (pin 28 of connector B) reaches pin 10 of the junction unit located in headlamp F10.Pins 11 of the two headlamps are connected to the diagnostic K lineThe Body Computer M1 is connected via the CAN line to the instrument panel E50 to manage the "main beam headlamps" warning light.