Fiat BRAVO 1.9 JTD 16v – ELECTRIC REAR WINDOWS – – WIRING DIAGRAM, LOCATION COMPONENTS, OPERATIONAL DESCRIPTION – WIRING DIAGRAM, LOCATION COMPONENTS, OPERATIONAL DESCRIPTION

WIRING DIAGRAM - ELECTRIC REAR WINDOWS - Fiat BRAVO 1.9 JTD 16v

ELECTRIC REAR WINDOWS - WIRING DIAGRAM Fiat BRAVO 1.9 JTD 16v

COMPONENTS - ELECTRIC REAR WINDOWS - Fiat BRAVO 1.9 JTD 16v

Component code	Description	Reference to the operation
B001	JUNCTION UNIT
B002	JUNCTION UNIT UNDER DASHBOARD
B099	MAXI FUSE BOX ON BATTERY	-
C020	PASSENGER SIDE DASHBOARD EARTH	-
C030	LEFT REAR EARTH	-
C038	EARTH ON CENTRE TUNNEL	-
D030	DRIVER'S FRONT DOOR COUPLING	-
D035	LEFT REAR DOOR COUPLING	-
D036	RIGHT REAR DOOR COUPLING	-
H001	IGNITION SWITCH
H044	ELECTRIC WINDOW CONTROLS ON FRONT DRIVER'S DOOR
H053	ELECTRIC WINDOW SWITCH ON LEFT REAR DOOR
H054	ELECTRIC WINDOW SWITCH ON RIGHT REAR DOOR
M001	BODY COMPUTER
N065	LEFT REAR ELECTRIC WINDOW MOTOR
N066	RIGHT REAR ELECTRIC WINDOW MOTOR
P093	AERIAL FOR ALARM AND CENTRAL LOCKING RECEIVER	-

COMPONENT LOCATION - ELECTRIC REAR WINDOWS - Fiat BRAVO 1.9 JTD 16v

REAR ELECTRIC WINDOWS - COMPONENT LOCATION Fiat BRAVO 1.9 JTD 16v

获取访问所有汽车的接线图

Component code	Description	Reference to the operation
B001	JUNCTION UNIT
B002	JUNCTION UNIT UNDER DASHBOARD
B099	MAXI FUSE BOX ON BATTERY	-
C020	PASSENGER SIDE DASHBOARD EARTH	-
C030	LEFT REAR EARTH	-
C038	EARTH ON CENTRE TUNNEL	-
D030	DRIVER'S FRONT DOOR COUPLING	-
D035	LEFT REAR DOOR COUPLING	-
D036	RIGHT REAR DOOR COUPLING	-
H001	IGNITION SWITCH
H044	ELECTRIC WINDOW CONTROLS ON FRONT DRIVER'S DOOR
H053	ELECTRIC WINDOW SWITCH ON LEFT REAR DOOR
H054	ELECTRIC WINDOW SWITCH ON RIGHT REAR DOOR
M001	BODY COMPUTER
N065	LEFT REAR ELECTRIC WINDOW MOTOR
N066	RIGHT REAR ELECTRIC WINDOW MOTOR
P093	AERIAL FOR ALARM AND CENTRAL LOCKING RECEIVER	-

DESCRIPTION - ELECTRIC REAR WINDOWS - Fiat BRAVO 1.9 JTD 16v

The electric windows in the rear doors are activated using the switches in the actual doors and the driver''s front door.The motors are operated either manually or automatically, depending on the trim level.Automatic operation takes place as follows:- if the button is pressed is between 60 and 300 milliseconds, operation is manual: the glass goes up/down only with the key pressed;- f the key is pressed for longer than 300 milliseconds, operation is automatic: even if the button is released, the glass continues to move up/down until the end of travel position is reached or until the intervention of the anti-pinch safety system;- pressing the button again whilst the window is moving stops it in the position it is in;- if the button is pressed for less than 60 milliseconds, this is ignored (it is treated as an accidental knock).The electronic circuit inside the motor manages the antipinch function: i.e. it acquires information about the possible presence of an obstacle during window closure (rising); the antipinch function is performed by a Hall effect sensor that senses overloads on the window motor; the action threshold is set when the force of the obstacle encountered along the window travel (e.g. a finger, a hand) exceeds 7/8 kg.In addition, if a fault is detected, the control unit inhibits the automatic raising operation only allowing it in steps of 500ms each time the button is pressed.the windows are automatically opened or closed through the special prolonged (more than 2 seconds) command sent by the remote control button.The electric window function operates only with the ignition on, with the following exception: after key-off, the windows may be operated for a period of 3 minutes. When this period has elapsed, the system cannot receive new commands. If opening of one of the doors is detected during the timed period, no new commands are received but any commands received before door opening are completed. If one of the doors is already open at key off, any commands received before door opening are completed.The rear control lock (protection) is operated by means of a LOCK key among the driver''s controls: the locking status is indicated by an LED beside the key lighting up and the rear control buttons are not lit up. The electric windows cannot be operated using any of the buttons when the lock function is activated.768Electric windows system initialization:If the power supply has been disconnected the following procedure must be carried out to reset the electric windows system, using the controls on the driver''s front door.Proceed as follows for each door:- turn the ignition key to the ON position;- press the window closing button in "manual" mode (continuously) until the window is closed and keep it pressed for at least 1 second;When this procedure has been carried out, the anti-crush safety function and the automatic operation of the electric window are working.

FUNCTIONAL DESCRIPTION - ELECTRIC REAR WINDOWS - Fiat BRAVO 1.9 JTD 16v

Body Computer M1 - pin 32 of E - supplies the control unit on the driver''s door H44 - pin 1 and - if the LOCK button is not on - also the controls on the rear doors H53 and H54 - pin 2; this supply also turns on the lighting LEDs. Similarly, motors N65 (left) and N66 (right), pin 3, are supplied in accordance with the above strategy from pin 13 of connector D of M1.The Body Computer M1 receives a direct supply from the battery via the line protected by maxifuse B99 at pin 18 of connector F of the interface with the junction unit under the dashboard B2; the ignition-controlled supply (INT) reaches pin 9 of connector F of the interface with the junction unit B2.The services relay T13, located in the junction unit under the dashboard B2, supplies the motors N65 and N66 - pin 6 - via two lines protected by fuses F33 and F34 through the logic described above and controlled by the Body Computer M1 - pin 14 of connector F.The signals from the aerial-receiver of remote control unit P93, connected to pins 30 and 43 of connector B of M1, also control the opening/closing of the rear electric windows.