DescriptionIn the case of poor visibility, it is possibleto activate demisting of the rear windscreen and the door mirrors.The heating resistances for thesecomponents absorb a considerable amount of energy and they are thereforechecked and deactivated after a certain period: the defrosting istimed, according to the following logic, managed by the Body Computer:ignition ON (INT/A);activation signal from the relevant button, located onthe climate control system control panel.In these circumstances the resistances remainsupplied for a maximum of 20 minutes, then the power supply is cutoff.The power supply is also cut offunder the following conditions:ignition in OFF positiondeactivation signal from the relevant button;battery voltage below 8.5 Vafter the first 10 minutes operation, if the engine speedis below 1000 rpm.When the demister is on, a warning lighton the climate control system control unit is activated.
Functional description The heated rear windscreen relay T11,located in the underdashboard junction unit B2, controls the simultaneousactivation of the defrosting function for both the heated rear windscreenP55 and the resistances located in the mirrors P60 and P61 via thelines protected by fuses F40 and F41, respectively of junction unitB2. The supply for the coil for relay T11is 'controlled by the ignition' (INT/A) and is energized by an earthsignal coming from the Body Computer M1 - pin 6 of connector F; this signalis sent according to the complex control logic described previouslyand, in particular, when a signal arrives - at pin 32 of connectorG of M11 - from the heated rear windscreen button. This signal comes from climate control unit H80 ,which receives the feedback signal for activation of the relevantled - from pin 21 of connector H of M1 -.
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b).2044997
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212429579-7040A30Left instrument panellower TRIM - R.R.1. Disconnect the electrical connections (1a, 1b, 1c, 1d, 1e, 1f).2. Undo the left-threaded bolt securing the facia trim mount beam.3. Undo the bolts securing the body computer/junction unit.4. Move facia trim (4a) slightly and move body computer/junctionunit (4b) downwards.5. Disconnect the electrical connections (5a, 5b, 5c).6. Recover the body computer/junction unit.2045005
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect electronic control unit electrical connections (1a),(1b), (1c).2. Undo the bolts.3. Recover the control unit2045007
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect electronic control unit electrical connections (1a),(1b), (1c).2. Undo the bolts.3. Recover the control unit2045008
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Release the switch unit (1a), releasing the retainers (1b).2. Disconnect the electrical connections (2a (2b).3. Recover the switch unit.2045153
7005M12
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Release the switch holder trim (1a), releasing the retainers(1b).2. Disconnect the electrical connection.3. Keep the switch holder trim.2045154
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect the electric window motor connection.2. Undo the bolts.3. Remove the motor releasing the splined shaft.2045156
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Unscrew the motor retaining bolt.2. Disconnect the electrical connections for the motor (2a, 2b).3. Remove the distribution motor (3a) or the mixture motor (3b)releasing the intake.2044976
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212429574-7040A18glove compartment onfacia - arrange1. Unscrew the motor retaining bolt.2. Disconnect the motor electrical connection.3. Remove the motor releasign the intake.2044977
5040D96
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212429574-7040A18glove compartment onfacia - arrange1. Unscrew the motor retaining bolt.2. Disconnect the motor electrical connection.3. Remove the motor releasign the intake.2044978
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212429529-7015A04tailgate interior panel- r+r2429358-5050C34rear wiper arm with blade - r+r2429359-5050C42rear wiper motor - r+r1. Remove the rearscreen wiper motor shaft seal.2. Disconnect the heated rear window electrical connections (2a,2b).Move aside the electrical connections onthe rear window side so as not to damage them while cutting thebead of sealant.3. Apply a double layer of adhesive tape to protect the edges ofthe bodywork.2045199
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Fit a plastic spatula (1a) between the reflector (1b) and thecasing (1c) and release the reflector retainers (1d) from the circularsupport (1e).2. Disconnect the electrical connections for the reflector defroster.3. Recover the reflector.2045161
7005R36
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212429522-7005R35door mirror reflector- r r1. Undo the bolts.2. Disconnect the electrical connection.3. Keep the motor assembly.2045162
7005R37
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212429522-7005R35door mirror reflector- r r1. Release the two retainers (1a) and remove the cover (1b).2045163
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212429521-7005R30electrically controlleddoor mirror (one) - r+r2429522-7005R35door mirror reflector - r r2429523-7005R36door mirror motor - r r2429524-7005R37door mirror boot - r r1. Mark the position of the retainer (1b) on the pin (1a) (so thatthe spring (3) is correctly loaded when refitting) then releasethe retainer (1b) from its housing. 2. Remove the mirror shell.3. Keep the spring.4. Undo the bolts.5. Remove the flange and pin.6. Release the outside temperature sensor from its housing.7. Release the seal from its housing.8. Remove the cable loom, including the outside temperature sensor,releasing it from the retainers. 2045164
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Čeština
Dansk
Deutsch
Ελληνικά
English
English
Español
Suomi
Français
Français
עברית
Hrvatski
Magyar
Italiano
日本語
한국어
Nederlands
Polski
Português
Português
Română
Русский
Slovenčina
Slovenščina
Svenska
Türkçe
