DescriptionThis device allows maximum ease of manoeuvring during parking; with reverse gear engaged, it indicates if the driver is approaching an obstacle that could be outside his field of vision, as illustrated in the diagram below.The system operates in accordance with the ultrasound 'sonar' principle: four ultrasound transducers are located in the rear bumper. They send signals to a control unit, which processes this information and determines the distance of possible obstacles. A loudspeaker controlled by the control unit emits an intermittent tone, proportional to the distance of the obstacle detected. The control unit is activated when reverse gear is engaged: under these conditions it energizes the transducers and sends them a signal request, and receives response signals from them.The control unit emits a signal with intermittent tone: the frequency of this sound increases as the bumper comes close to an obstacle: when the calculated distance falls below 25 cm, the sound becomes acute and constant.If the distance measured from the obstacle increases, or if the driver disengages reverse gear, the sound stops. If the distance measured from the obstacle remains constant, the sound ceases after about 3 seconds. For more details and information on the operation of the system, 3308556Characteristic of working principle5580Hparking obstacle detection deviceThe control unit is located inside the luggage compartment, on the left side; beside the control unit there is an acoustic device.
Functional description Parking sensor control unit M84 is supplied pin 1 of connector A by the ignition-operated line (INT/A) for relay T24 of B45 protected by fuyse F78; Pin 8 of connector A is earthed. Pin 6 of connector A of M84 receives the reverse gear engaged signal SeeE2022 REVERSING LIGHTS . Pin 1 of connector A of M84 receives the speedometer signal from the instrument E50 pin 5 of connector B. The parking sensor P44 buzzer is connected to pins 2 and 10 of connector A of control unit M84. Pin 5 receives an inhibition signal if a trailer is connected via coupling D73 SeeE2050 TRAILER WIRING . The four parking sensors K97 are connected to connector C of control unit M84 : pin 1 supplies a reference earth, pin 6 the power supply, pins 5, 3, 2 and 4 are connected to sensors K97A , K97B , K97C and K97D . Self-diagnostic data can be read by connecting the unit to connector R10 pin 13: this receives signals from pin 12 of connector A of control unit M84 through the relevant tester line SeeE8010 DIAGNOSTIC MULTIPLE CONNECTOR .
0Removing201Refitting213314824-5505A18multi-function controlunit - r r . 1. Undo the bolt (1a) and push back the junction unit as far asnecessary to disconnect the electrical connections (1b).767For precise identification ofthe electrical connections, see Wiring Diagrams Section.2. Remove the junction unit.2010592
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Unscrew bolt (1a) and open fuse access cover (1b).2. Undo the bolt (2a) and remove the integrated multiservices unit(2b) after having disconnected the electrical connections (2c),(2d), (2e), (2f) and (2g).2010595
5505A29
0Removing201Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b) for theadditional junction unit.2071293
0Removing201Refitting213314864-5530B54battery cover - r+r . Make sure that the ignition key is in theOFF position.1. Disconnect the battery negative and positive terminals.2. Undo the bolt (2a) fixing the battery retaining bracket (2b).3. Remove the battery.2010647
5530B40
0Removing201Refitting213314864-5530B54battery cover - r+r1. Press and release the retainers (1a), then remove the cover (1b)for the supply box on the battery. 2071303
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). Lower the steering wheel and move it back.1. Undo the bolts (1a) and remove the upper half casing for thesteering column (1b).2010703
5560B12
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). Open the fuse carrier compartment flap.1. Using the tool (1a) and pushing the fuse carrier compartment,remove the surround (1b) complete with switches.2. Disconnect the elelectrical connections (2a), (2b) and (2c) andremove the surround complete with switches.2010706
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.